Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | STRUCTURAL REPAIRS & EXTERNAL PAINTING: |
| 2 | SUPPLYING AND ERECTING SINGLE/DOUBLE BAMBOO ALONGWITH HASSION CLOTH SCAFFOLDING:- Supplying and erecting Single or double bamboo scaffolding as per site conditions along with hassion clothas required with verticals @ 1.2m to 1.8m c/c inner as well as outer faces and horizontals and braces on the Building structure or any other places without any puncher to wall surface etc. including the removal of scaffolding after completion of the work etc. all complete as per the direction of Consulting Engineer / in-charge.Rate Inculding providing and fixing full cover hassion cloth vertical surface of the buidling for entire execution of work and necessary safety nylon net fixing on horizontal surface in the premises as required location. NOTE- MODE OF MEASUREMENT OF SCAFFOLDING WILL BE AS PER BUILDING LENGTH IN PERIPHERI & HIGHT UP TO PARAPET WALL LEVEL.ITEM OF SCAFFOLDING WILL BE PAID ONLY ONE TIMEFOR THE ENTIRE WORK EXECUTION.FOR ERECTION OF SCAFFOLDING WILL PAID 50% OF QUOTED RATE AND REMAIN 50% WILL BE PAID AFTER REMOVEING THE SAME BILLING WILL BE AS PER THE EXECUTEDQUANTITY AND MEASUREMENT. |
| 3 | DOUBLE SCAFFOLDING SYSTEM(cup lock type):Providing and fixing double scaffolding system (cup lock type) on the exterior side of G + 13 storeyed building/structure for all heights above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform,net for capturing falling debris, hessian fabric cloth ( having opaqueness > 90 % ) for safety etc. and maintaining it in a serviceable condition duringexecution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once (one time) only for execution of all the items of works requiring scaffolidng (3) No extra/additional payment shall be made for removal and refixing of scaffolding, if done by the contractor for any reason/s. (4) Entire scaffolding material used shall be the property of the contractor and shall be removed and taken away by the contractor after completion of work. (5) Any damages to the wall and other parts of the building caused due to the fixing and removing of scaffolding shall be repaired by the contractor on his own cost. Rate Inculding providing and fixing full cover hassion cloth vertical surface of the buidling for entire execution of work and necessary safety nylon net fixing on horizontal surface in the premises as required location. NOTE- MODE OF MEASUREMENT OF SCAFFOLDING WILL BE AS PER BUILDING LENGTH IN PERIPHERI & HIGHT UP TO PARAPET WALL LEVEL.ITEM OF SCAFFOLDING WILL BE PAID ONLY ONE TIMEFOR THE ENTIRE WORK EXECUTION.FOR ERECTION OF SCAFFOLDING WILL PAID 50% OF QUOTED RATE AND REMAIN 50% WILL BE PAID AFTER REMOVEING THE SAME BILLING WILL BE AS PER THE EXECUTEDQUANTITY AND MEASUREMENT. |
| 4 | WINDOW COVERING :Providing and fixing 6 mm thick old/ new commercial plywood in servicable condition with new/ old jungle wood frame work of 50 x 35 mm size at 60 cm on One ways for closing the window portion/openings for protection from falling debris, dust etc. including cutting, fixing with nails and removing after the same after completion of the work. (In event of any damage to existing windows, shall be the same shall be repaired by the contractor on his own cost) |
| 5 | REMOVAL OF EXISTING CEMENT PLASTER:-Dismantling/ Removal of the existing old plaster (both internal and external) of any thickness and at all levels by chisel & hammer / cutter plate or skirting including raking out joints and cleaning the surface for re-plaster. Rates quoted to include removing all debris, spalls, including cleaning the site, lowering down the debris to the ground without causing dust nuisance and damage to the structure and disposing & carting away the debris outside the building compound upto the municipal dump site with necessary municipal permision with all lead and lift. |
| 6 | BREAKING/CHIPPING LOOSE CONCRETE:-Chipping and removing theloose/ unsound/ weak concrete with manual chisel and/ or by standrad power driven percussion type of approved make equipment upto reinforcing bars, without removing the reinforcement, including tapering of all edges, making square shoulders of cavities, removing all the loose materials, cleaning the surface by water jet pressure pump to make all the exposed surface free from dust, oil and all impurities, etc. and air drying the surface, etc. complete as directed for all locations. Including disposing & carting away the debris outside the building compound upto the municipal dump site with necessary municipal permision with all lead and lift.(Note:-Exposed Surface area prepared for repair of structural member shall be considered for payment)Only the damaged area of concrete will be measured. |
| 7 | REMOVAL OF EXISTING WATERPROOFING:Removing the existing waterproofing layers of china mosaic flooring/screed ofany thickness on theexisting terraceincluding surface prepration & cleaning it. Rates shall be quoted to include removing all debris, spalls, including cleaning the site, lowering down the debris to the ground floor without causingdust nuisance and damage to the structure and disposing & carting away the debris outside the building compound upto the municipal dump with required municipal permision with all lead and lift, etc. complete as directed. |
| 8 | STRUCTURAL POLYMER REPAIR (UPTO 15mm THICKNESS):Repairing to the existing RCC structural members (vertical or horizontal) using ready mix Polymer Modified Mortar (Fibre reinforced structural grade repair mortar) of approved brand where the thickness of repair is upto 15 mm. It can be used for carrying out extensive repairs to beams, columns, slab, and other structural elements, repairing of structural members subjected to repetitive loading for strengthening. Procedure for carrying out repair Polymer Modified Mortar -Surface preparation- (separate payment shall be made ) All loose traces of concrete or mortar, dust, grease oil, etc. must be removed. Damaged or contaminated concrete shall be removed to obtain a keyed aggregate exposed surface. Non-impact/ vibrating cleaning methods, e.g. grit or high pressure water blasting are recommended. Clean all exposed reinforcement to a minimum grade of Sa 2 according to ISO 8501-1 / ISO 2944-4. Ensure all visible portions of the reinforcing bar is clean. Where reinforcing bars are corroded, cut back the concrete around the reinforcing bars, Grit blast to remove corrosion products from around reinforcing bars and coat with approved epoxy coating for corrosion protection or any other protective coating as recommended by the Structural Engineer to protect from corrosion. Replace the affected part of rebar if the diameter after grit blasting is found reduced by more than 20% of the original diameter on the advice of the structural engineer responsible for the works. Bond Coat- (separate payment shall be made only for bond coat used for old surface to new surface) Providing & applying One coat of structural grade epoxy bond coat by brush conforming to ASTM-C-882-87 to the prepared concrete surface to be repaired / strengthened and repairingwith PMM shall be done when the surface is tacky. Mixing -Only full bags are mixed. Damaged or opened bags should not be used. Mix the ready-mix Polymer Modified Mortar in a forced action pan mixer, or with a helical paddle attached to alow speed (300-600rpm) mixer for 3 minutes until a lump free, thixotropic consistency is achieved. Only use clean water. Mixing water needed: 3.75 to 4.25 litres per 25kg bag or as recommended by the Manufacturer of Polymer Modified Mortar. Allow the mortar to rest for 2 - 3 minutes and then nremix briefly before pouring into formwork. If temperature more than 40°C then use chilled water for mixing.Mortar application- The minimum temperatures must be maintained duringapplication and for at least 24 hours thereafter for optimumcuring of the product. The prepared substrate should be presoaked, preferably for 24 hours, but at least 2 hours beforeapplying Polymer Modified Mortar. The surface must besaturated surface dry, but without standing water. PolymerModified Mortar can be spray- or hand-applied. Apply mixedproduct directly to the prepared damp substrate, or wet on wetonto the primed surface. Spraying the material with the necessary pressure will ensure good adhesion o fthematerial.A thin scrape coatorcontac tlayer before building upto ther equired thickness, wet on wet, will improveadhesionespecially in case of hand application. Apply to the desiredlayer thickness upto 15 mm and level using a screeding bar,trowel or woodenboard. Smoothing with a trowel or finishingby float or sponge can be done as soon as the mortar hasbegun to stiffen.Protective coatings - Subsequent coatings of any anticarbonation barriers or silaneimpregnationsshouldbeapplieifrecommendedbytheStructural Engineer.Plaster- (No separate payment shall be made).The repaired surface shall be matched to the surroundingsurface by providing required thickness of plaster internal orexternal plaster.CuringMinimum 7 days curing shall be done to the newly repairedareausingany suitablemethodRequiredCompressivestrength(ASTC1097cmcube)ReadyMixPolymerModifiedMortar used on site shall besentfortestingofcompressivestrengthandminimumstrengthrequired to be achieved is as follows – 1 Day-15 MPa, 3 Day-25 MPa, 7 Day-35 MPa, 28 Day-45 MPa.Surface Coating -Providing surfsce coating of polymer after completion of structural repair work. |
| 9 | STRUCTURAL POLYMER REPAIR (From 15mm to 30mm THICKNESS): Repairing to the existing RCC structural members (vertical or horizontal) using ready mix Polymer Modified Mortar (Fibre einforced structural grade repair mortar) of approved brand where the thickness of repair is upto 30 mm in two layers. Itcan be used for carrying out extensive repairs to beams, columns, slab, and other structural elements, repairing of structural members subjected to repetitive loading for strengthening. Procedure for carrying out repair Polymer Modified Mortar - Surface preparation- (separate payment shall be made )All loose traces of concrete or mortar, dust, grease oil, etc.must be removed. Damaged or contaminated concrete shallbe removed to obtain a keyed aggregate exposed surface.Non-impact/ vibrating cleaning methods, e.g. grit or highpressure water blasting are recommended. Clean all exposedreinforcement to a minimum grade of Sa 2 according to ISO8501-1 / ISO 2944-4. Ensure all visible portions of thereinforcing bar is clean. Where reinforcing bars are corroded,cut back the concrete around the reinforcing bars, Grit blast toremove corrosion products from around reinforcing bars andcoat with approved epoxy coating for corrosion protection orany other protective coating as recommended by theStructural Engineer to protect from corrosion. Replace theaffected part of rebar if the diameter after grit blasting is foundreduced by more than 20% of the original diameter on theadvice of the structural engineer responsible for the works.Bond Coat- (separate payment shall be made only for bondcoat used for old surface to new surface)Providing & applying One coat of structural grade epoxy bondcoat by brush conforming to ASTM-C-882-87 to the preparedconcrete surface to be repaired / strengthened and repairingwith PMM shall be done when the surface is tacky.Mixing -Only full bags are mixed. Damaged or opened bags should notbe used. Mix the ready-mix Polymer Modified Mortar in aforced action pan mixer, or with a helical paddle attached to alow speed (300-600rpm) mixer for 3 minutes until a lump free,thixotropic consistency is achieved. Only usec leanwater.Mixing water needed: 3.75 to 4.25 litres per 25kg bagorasrecommendedManufacturerofPolymerModifiedMortar.Allowthemortar to rest for 2 - 3 minutes and thenremix briefly beforepouring into formwork. If temperature morethan 40°C then use chilled water for mixing.Mortar application-The minimum temperatures must be maintained duringapplication and for at least 24 hours thereafter foroptimumcuring of the product. The prepared substrate should be presoaked,preferably for 24 hours, but at least 2 hours beforeapplying Polymer Modified Mortar. The surface must besaturated surface dry, but without standing water. PolymerModified Mortar can be spray- or hand-applied. Apply mixedproduct directly to the prepared damp substrate, or wet on wetonto the primed surface. Spraying the material with thenecessary pressure will ensure good adhesion of the material.A thin scrape coat or contact layer before building uptotherequiredthickness,wetonwet,willimproveadhesionespeciallyincaseofhandapplication.Applytothedesiredlayerthickness upto 15 mm in single layer and after hardening,provide second layer of required thickness (total upto 30 mm)and level using a screeding bar, trowel or wooden board. Ifrequired, bond coat shall be provided as per therecommendation of manufacturer between two layers ofpolymer Modified Mortar and no separate payment shall bemade for it. (However, between old & new surface of concretebond coat shall be applied & paid separately) Smoothing witha trowel or finishing by float orsponge can be done as soon asthe mortar has begun to stiffen.Protective coatingsSubsequent coatings of any anticarbonation barriers or silaneimpregnationsshouldbeapplieifrecommendedbytheStructural Engineer.Plaster- ((No separatepaymentshallbe made))The repaired surface shall be matched to thesurroundingsurface by providing required thickness of plaster internal orexternal plaster.CuringMinimum 7 days curing shall be done to the newlyrepaired/jacketed area using any suitable method.Required Compressive strength (ASTM C109 7cm cube)Ready Mix Polymer Modified Mortar used on site shall be sentfor testing of compressive strength and minimum strengthrequired to be achieved is as follows – 1 Day-15 MPa, 3 Day-25 MPa, 7 Day-35 MPa, 28 Day-45 MPa. Surface Coating - Providing surfsce coating of polymer after completion of structural repair work. |
| 10 | MICRO CONCRETE:Repairing the existing damaged RCC structural members (vertical or horizontal) or strengthening itby supplying & applyingready mix Micro Concrete of approved brand & make conforming to EN1504 Part 3 (Properties: 28 days compressive strength≥ 55 MPa and Bond Shear Strength ≥ 10 MPa at 14 days), where the thickness of repair is more than 30 mm and upto 115 mmwhen the epoxy bond coat is tacky, including supplying & applyingbond coat ???, cost of fixing and removal of good quality shuttering or forms treated with a chemical release agent and braced to withstand the pouring pressure, pouring the microconcrete in forms at all levels & heights, proping, finishing the surface, curing, etc. complete as directed. The quoted rate shall include cost ofall these necessary operations relating to extensive repairs to beams,columns and other structural members. For repairs beyond 80mm to 115mm in thickness, extend Ready Mix Micro Concrete with up to 25kg of 5-12mm sized washed, saturated surface-dry (SSD), graded low absorption, high density aggregates. The microconcrete shall be mixed, applied and cured as per the manufacturer\"s technical specifications (Note: Payment is to be made by weight premixed of micro concrete product consumed as per site register records) |
| 11 | GROUTING NIPPLE:Providing, drilling and fixing Nipples for pressure injection grouting of polymer cement grout etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 12 | INJECTION GROUTING:Providing Grouting by specially prepared grout of approved make chemical with cement in proportion 1:3.5 (1 part chemical & 3.5 part cement by weight) along with 50 ml super plasticizer non cracking antiwash high strength polymer cement grout P C grout available in bags or equivalent with proper water for injectable consistency and applying it in the body of structure like slab, beam, column, pillars, deckslab, retaining wall, basement, underground and elevated water storage reservoir concrete and brick wall, crack portion of structure etc. by injecting method, to achieve its original strength including drilling of suitable diameter drills holes at 2 to 4 Nos. per sqm. using caps and nozzle grouting machinery necessary, scaffolding, finishing etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 13 | SHEAR CONNECTOR: Make 10/12 mm Dia holes using heavy duty electrically operated hammer drills in the concrete of RCC members to a depth of about 75 mm at 500 mm c/c or at suitable grid in zig-zag fashion, clean the holes using air jet and fix pre-fabricated 100 x 50 mm L-shape 8mm Dia rebar using Anti Corrosive protective coating so that 75 mm out of 100 mm is inserted inside the concrete and 25 mm remain outside along with 50 mm bend. The shear connectors are used to tie the additional reinforcement bars with \"Fischer / Hilti\" system and chemical, etc. complete. Steel to be paid separately etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 14 | NEW REINFORCEMENT STEEL:Providing, fabricating, welding & fixing steel reinforcement (Fe500) in existing damaged reinforcement in RCC as required Dia of approved brand i.e. TATA/SAIL or equivalent. For column, beams & slab. Etc. including transporting the same to site, cutting, bending, tying at all heights and in all positions, providing concrete covers as required at any height etc. Rates to include MS/TS dowel pins /staple/shear pins including drilling holes in concrete and providing labour and materials for fixing the pins etc. Complete as per the direction and approval of Consulting Engineer In-charge. |
| 15 | M.S. STEEL PROPS:-Providing and erecting steel tubular props of required height upto 14\" feet, L head or flat head braced at center and supporting a continuous 2\" x 3\" wooden runner, resting on wedge and block minimum capacity 3 Ton to support the structure provisionally during repair and jacketing etc. and maintaining them in position till all required item are complete. The props are erected in perfect vertical in plumb taking / transferring the load equally / uniformly. The location of every prop should be one over another floor and it should not be eccentric. The tightening of every prop should be uniform to all props to strain the building uniformly, removing the same as per the direction and approval of Consulting Engineer In-charge. Payment will be made location wise and based on nos. of props. fix at site. |
| 16 | EXTERNAL SAND FACE PLASTER:Providing and applying external sand faced cement plaster at all positions and levels with cement mortar ( 1 cement :4 fine screened sand ) in two coats for masonry and concrete surfacesincluding surface preparation, raking out joints, hacking concrete surface, base coat of 15mm thick in C.M. 1:4 added with approved water proofing admixture conforming to IS 2645 and 6mm long polypropylene fibers conforming to ASTM C 1116 Type III in proportions recommended by the manufacturer specifications and curing the same for not less than three days and keeping the surface of base coat rough to receive the sand face treatment 6 to 8 mm thick of C. M 1:3 finishing the surface by taking out grains and curing for 7- 10 days, providing bands, drip moulds, grooves, finishing corners, etc complete as per instructions and directions of the Engineer-in-Charge. Phaseof all repaired foundation shall be coated with DECKGAURD S (protective layer ) or approved equivalent mentioned in the tender document in 2 coats at the rate of 0.35 lt/ sq.m. |
| 17 | DASH COAT:Providing Dash Coat plaster in C:M. 1:4 upto 40 mm thick to concrete or brick surface in all positions including racking out joints, curing etc. complete.as per the direction and approval of Consulting Engineer In-charge. |
| 18 | SEPARATION JOINT FILLING :Providing and applying crystalline mortar by mixing in the ratio of 4.5:1 (4.5 parts crystalline mortar: 1 part water) for the treatment of cracks on the surface of walls, ceilings, junction of RCC and masonry, etc. by opening the cracks for a size of 50 mm wide and 75 mm deep from either side of the cracks using cutter machine or chiseling with a well sharpened chisel and hammer cutting to form a V groove all along the length of the crack, cleaning the groove with wire brush, surface preparation by washing with water jet, priming the grooved area with integral crystalline slurry at 0.05 Kg/ running meter and e and while the surface is tacky, fill the groove upto existing plaster surface with crystalline mortar @1.50 kg/running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05 kg/running metre per coat and making the surface similar to the adjacent plastered surface using wooden floats/ punch, etc. complete as specified and directed by the Engineer-in-Charge. |
| 19 | CHICKEN MESH:Providing and fixing chicken wire mesh of 22 gauge of 30 cm width at the junction of RCC members and brick work of approved quality, prior to plastering, including fixing mesh in necessary position at all positions by necessary drilling/ nailing in concrete/ masonry, etc. complete as specified and directed by the Engineer-in-Charge at all locations. |
| 20 | INTERNAL PLASTER STAIRCASE AND INTERNAL FLAT AREA:Providing and applying internal plaster in single coat in CM 1:4in 10 to 13 millimeter thickness to previously plastered surface/or on newly brick surface(Excluding rough cast plaster)in all position including preparing and Finishing the surface scaffolding etc.completeas per the direction and approval of Consulting Engineer In-charge. Item inculding scaffolding and hassion cloth as requiredPhaseof all repaired foundation shall be coated with DECKGAURD S (protective layer ) or approved equivalent mentioned in the tender document in 2 coats at the rate of 0.35 lt/ sq.m. |
| 21 | WATER TANK INSIDE WATERPROOFING:Providing and applying a base coat comprising of 1 Kg Polydee-MC and 1 Kg fresh cement after wetting the surface followed by drying the surface for 2 days, apply primer coat of TP-40 and after drying, applying Polydee-11 two component (mixing ratio 2 A : 1 B) ) Antibacterial food grade certified by CFTRI or similar organisation coating inside drinking water tank in two coats with time interval of minimum 8 hrs. covering 7 years guarantee on non-judicial stamp Paper of Rs. 100/- etc. complete as per the direction and approval of Consulting Engineer In-charge. Item inculding scaffolding proper cleaning as required. |
| 22 | CHAJJATOP WATERPROOFING:Providing & laying Waterproofing Treatment to chajja Top upto required thickness including scaffolding, preparation of surface as required, waterproofing procedure consisting of following operations: A) Cleaning the surface & making free from loose particles, filling the cracks on slab, applying waterproof chemical in two coats on the terrace slab as per the specifications of Manufacturer. B) Laying brickbat coba using old broken brick/brick bats 25mm to 100 mm size with cement mortar upto 50% 1:5 (1cement: 5 coarse sand) admixed with proprietary waterproofing compound conforming to IS: 2645 over 20mm thick layer of cement mortar mix 1:5 (1 cement 5 coarse sand) admixed with proprietary waterproofing compound conforming to IS: 2645 to required slope and treating similarly the adjoining walls upto 300mm height including rounding of junction of walls and slabs. C) After two days of proper curing providing & laying IPS in C.M 1:4 i/c marking lines to give appearance of tiles of 30cm x30cm or other size laid diagonally/square, ponding the entire area for 07 days etc. complete as per the direction of Consulting Engineer / in-charge.Rate of chajja waterproofing must be including of Round Vatta of 6” thick including making of strip mould at the junction of vatta and wall plaster. And making of drip mould in bottom of chajja.as per the direction and approval of Consulting Engineer In-charge. |
| 23 | TERRACE TOP WATERPROOF IPS & CHINA MOSAIC:Filling all the cracks/voids with cement sand mortar to making the surface smooth then providing 02 coat of waterproof chemical of approved brand two coats of waterproofing chemical with a broad stiff brush in long paralleled strokes complete and thereafter providing & doing Cement mortar (IPS) made from cement and fine sand in proportion of 1:5 is spread uniformly on the surface of 20 mm to 25 mm uniformly. This bed is left to harden for one day and make the surface rough to receive the china Mosaic. Cure the finished IPS for atleast seven days.Providing & Fixing mix colourd china mosaic in cement mortar 1:4 and pressed & filled in position. The joints between these two pieces shouldn’t exceed more than 3 to 4 mm. These pieces are hammered with wooden mallet to achieve uniform surface. Make the projected edge (kani) between the parapet plaster and the watta on second day.The surface is cleaned with saw dust to remove excess cement sticking to the glazed china mosaic surface. If surface is not cleaned thoroughly by this method then the same shall be cleaned with dilute acid after one month, as directed by the consultants. Completed work is then cured for 15 days by ponding method including stitching of joints between terrace & Parapet as per direction of consulting Engineer In-Charge. |
| 24 | TERRACE, LIFT ROOM, WATER TANK TOP, STAIRCASE HEAD ROOM AND PARAPET WALL SURFACE WATERPROOFING COATING OF DR. FIXIT ROOFSEAL ULTRA OR EQUIVALENT:-After surface prepration as per the product data sheet of Dr. Fixit roofseal ultra apply by using Dilute 2 parts of Dr. Fixit Primeseal with 1 part of water to cover 8 sq. m. Allow the primer coat to dry for 6 to 8 hours. Stir well before using.then Apply the 1st coat of Dr. Fixit Roofseal Ultra waterproof coating without dilution at a rate of 0.70-0.75 liters per sq. m. per coat. Lay down a 45 GSM fiber glass mesh into the coating as a sandwich layer while the first coat is still wet.Second coat application: Allow the first coat to dry for approximately 4-6 hours before applying the second coat at a 90° angle to the first coat. Apply the second coat of Dr. Fixit Roofseal Ultra waterproof coating without dilution at a rate of 0.70-0.75 liters per sq. m. per coat, ensuring total material consumption of 1.40–1.50 liters per sq. m. in 2-3 coats. Ensure there are no pinholes or air bubbles on the membrane. Allow the system to air cure for a minimum of 7 days.All work carryout as per the product data sheet of Dr. Fixit roofseal ultra and as per the Consulting engineer in-charge. rate inculidng for propoer surface prepration along with roughness of chinamosic surface to receive waterproofing coating. Performance warranty should be of 05 years. |
| 25 | PROVIDING AND FIXING PVC PIPE 100mm W/C LINE PVC :-Removing Existing Plumbing Lines & Providing and fixing new PVC pipes after removing the existing plumbing lines, Sealing the joints with leadwith all fittings and Nails, cutting holes in walls and remaking good the demolished portion complete and providing required GI Brackets as per the direction and approval of Consulting Engineer In-charge. NOTE: Rate including the provision of temporary plumbing lines during the execution if required. Item inculding scaffolding and hassion cloth as required.100mm W/C LINE PVC:-Providing & fixing new B class 100 mm PVC pipes of approved brand, with necessary fitures and fitting and Sealing the Joints with lead with all required fittings like connector Y & T and Nails, cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 26 | PROVIDING AND FIXING PVC PIPE 160mm RAIN WATER LINE PVC :-Removing Existing Plumbing Lines & Providing and fixing new PVC pipes after removing the existing plumbing lines, Sealing the joints with leadwith all fittings and Nails, cutting holes in walls and remaking good the demolished portion complete and providing required GI Brackets as per the direction and approval of Consulting Engineer In-charge. NOTE: Rate including the provision of temporary plumbing lines during the execution if required. Item inculding scaffolding and hassion cloth as required.160mm RAIN WATER LINE PVC:-Providing & fixing new B class 160 mmPVC pipes of approved brand, with necessary fitures and fitting and Sealing the Joints with lead with all required fittings like connector Y & T and Nails, cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 27 | PROVIDING AND FIXING PVC PIPE 75mm BATH/KITCHEN/BALCONY LINE PVC :-Removing Existing Plumbing Lines & Providing and fixing new PVC pipes after removing the existing plumbing lines, Sealing the joints with leadwith all fittings and Nails, cutting holes in walls and remaking good the demolished portion complete and providing required GI Brackets as per the direction and approval of Consulting Engineer In-charge. NOTE: Rate including the provision of temporary plumbing lines during the execution if required. Item inculding scaffolding and hassion cloth as required.75mm BATH/KITCHEN/BALCONY LINE PVC:-Providing & fixing new B class 75 mm PVC pipes of approved brand, with necessary fitures and fitting and Sealing the Joints with lead with all required fittings like connector Y & T and Nails, cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 28 | PROVIDING AND FIXING PVC PIPE 50mm VENT LINE PVC :-Removing Existing Plumbing Lines & Providing and fixing new PVC pipes after removing the existing plumbing lines, Sealing the joints with leadwith all fittings and Nails, cutting holes in walls and remaking good the demolished portion complete and providing required GI Brackets as per the direction and approval of Consulting Engineer In-charge. NOTE: Rate including the provision of temporary plumbing lines during the execution if required. Item inculding scaffolding and hassion cloth as required.50mm VENT LINE PVC:-Providing & fixing new B class 50 mm PVC pipes of approved brand, with necessary fitures and fitting and Sealing the Joints with lead with all required fittings like connector Y & T and Nails, cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 29 | PROVIDING AND FIXING PVC PIPE 32mm DIA AC PVC PIPE :-Removing Existing Plumbing Lines & Providing and fixing new PVC pipes after removing the existing plumbing lines, Sealing the joints with leadwith all fittings and Nails, cutting holes in walls and remaking good the demolished portion complete and providing required GI Brackets as per the direction and approval of Consulting Engineer In-charge. NOTE: Rate including the provision of temporary plumbing lines during the execution if required. Item inculding scaffolding and hassion cloth as required.32mm DIA AC PVC PIPE:-Providing & fixing new B class 32 mm PVC pipes of approved brand, with necessary fitures and fitting and Sealing the Joints with lead with all required fittings like connector Y & T and Nails, cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 30 | FIXING NEW DOWNTAKE, UPTAKE CPVC LINES 50mm DIA CPVC MAIN SUPPLY LINE:-Removing Existing Plumbing Lines, carting away dismantled material outside the building compound and Providing & fixing new CPVC pipes of approved brand, Sealing the Joints with lead with all required brass fittings like elbow etc., cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound inculding and providing required GI Brackets etc complete as per the direction and approval of Consulting Engineer In-charge. 50mm DIA CPVC MAIN SUPPLY LINE:-Providing and fixing 50 MM CPVC pipe of apprved brand at all level with required brass fitting and other required fitting etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 31 | FIXING NEW DOWNTAKE, UPTAKE CPVC LINES 25mm DIA CPVC PIPE:-Removing Existing Plumbing Lines, carting away dismantled material outside the building compound and Providing & fixing new CPVC pipes of approved brand, Sealing the Joints with lead with all required brass fittings like elbow etc., cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound inculding and providing required GI Brackets etc complete as per the direction and approval of Consulting Engineer In-charge. 25mm DIA CPVC PIPE:-Providing and fixing 25 MM CPVC pipe of apprved brand at all level with required brass fitting and other required fitting etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 32 | FIXING NEW DOWNTAKE, UPTAKE CPVC LINES 20mm DIA CPVC PIPE:-Removing Existing Plumbing Lines, carting away dismantled material outside the building compound and Providing & fixing new CPVC pipes of approved brand, Sealing the Joints with lead with all required brass fittings like elbow etc., cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound inculding and providing required GI Brackets etc complete as per the direction and approval of Consulting Engineer In-charge. 20mm DIA CPVC PIPE:-Providing and fixing 20 MM CPVC pipe of apprved brand at all level with required brass fitting and other required fitting etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 33 | FIXING NEW DOWNTAKE, UPTAKE CPVC LINES - REMOVING & REFIXING OF 50mm Dia Upvc/Cpvc PIPES :-Removing Existing Plumbing Lines, carting away dismantled material outside the building compound and Providing & fixing new CPVC/UPVC pipes of approved brand, Sealing the Joints with lead with all required brass fittings like elbow etc., cutting holes in walls & after fixing of pipe fill the gabda with waterproof compound inculding and providing required GI Brackets etc complete as per the direction and approval of Consulting Engineer In-charge. REMOVING & REFIXING OF 50mm Dia Upvc/Cpvc PIPES:-Removingandrefixingexisting Upvc/CPVC pipe50mm Dia CPVC pipes with allnew brass fittings if necessary complete including cleaning. as per the direction and approval of Consulting Engineer In-charge. |
| 34 | WALL PIECE:-Providing and fixing new Wall Piece of required sizes 25 mm with all necessary fittings after removing the existing lines, filling the joints, providing PVC sleeves on top, cutting holes in external walls complete as per the direction and approval of Consulting Engineer In-charge. |
| 35 | GATE VALVE 50mm :Providing and fixing gun metal gate valve with C.I. wheel of approved barand of 50 mm nominal bore complete as per the direction and approval of Consulting Engineer In-charge. |
| 36 | GATE VALVE 25mm :Providing and fixing gun metal gate valve with C.I. wheel of approved barand of 25 mm nominal bore complete as per the direction and approval of Consulting Engineer In-charge. |
| 37 | EXTERNAL TEXTURE PLASTER:Thoroughly cleaning all external wall surfaces, removing all fungus / plantation, removing old caulk from the plaster surface, making the surface imperfections such as holes, dents, small visible cracks by filling using mixture. Pre wetting of wall surfaces. Then apply one coat of base coat of paint then Mixing the product with clean water thoroughly with an electrical mixer for 3-5 minutes until the desired homogeneous paste is achieved so as to ensure that the mixture is free from lumps before use. Applying average thickness of 1.5 of the homogeneous paste thus prepared on the plastered surface with a steel trowel so as to have the desired texture finish. All this works to be carried out in accordance with the manufacturer’s specs and as per the direction and approval of Consulting Engineer In-charge. |
| 38 | EXTERIOR ELASTOMERIC BASED PAINT: Scrapping the surface to remove all loosely adhered particles followed by washing with plenty of water using wire brush and jet pressure washer so as to ensure thorough cleaning. Providing and applying 2 coats of (Asian Paints SmartCare Crack Seal) flexible, glass fibre reinforced acrylic crack filler after widening cracks up to 3mm width and any depth using scrapper blade or angle cutter. Prime the cracks using (Asian Paints Acrylic Exterior Wall Primer )before applying crack seal.Providing and applying one coat of (Asian Paints Ultima Protek BaseCoat) fibre reinforced liquid applied membrane having crack bridging ability up to 2.00 mm with topcoats without dilution . Also need to ensure forced coverage of 30-35 Sq.Ft/Ltr/Coat.Providing and applying twocoats of (Asian Paints Ultima Protek TopCoat) Organo-Silicon, UV Cross linking emulsion having (advanced anti algal) high resistance to growth of algae, (DPUR) Superior resistance to dust and dirt accumulation, (colour stay) resistance to fading of colours, protection against bird dropping and longevity of waterproofing and paint performance for 05 years so as to obtain an acceptable finish and ensuring coverage of 60 - 65 Sq.Ft/Ltr with 30-35% dilution with water. The work should be done by the manufacturer recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company representative. Note : Same scaffolding , hassion clost erected for civil works to be used for Exterrnal painting works. |
| 39 | STAIRCASE, INTERNAL FLATS & PARKING CELINGPAINTING:-Providing and applying first single coat of approved primer and two coats of acrylic plastic emulsion paint of an approved make and colour as per manufacturers specifications to any surface, at all height and locations as directed including reuuired scaffolding, cleaning and preparing surfaces for painting by any approved means etc. completeas per the direction and approval of Consulting Engineer In-charge. Item inculding scaffolding and hassion cloth as required. |
| 40 | SCRAPPING THE EXISTING PAINT/POP/LIME PUNNING/PUTTY LAYER IN STAIRCASE AND STILT: Scrapping the layer upto cement plastered surface from walls and ceiling area either manually with wire brush or blades or using mechanical devices and rubbing with sand paper at all locations and heights including scaffolding, tools, tackles, filling the cracks by supplying & applying premium acrylic crack filler putty of approved brand & make , even up the surface by any approved means, etc. complete as directed by the Engineer-in-Charge |
| 41 | WALL CARE PUTTY ON on STAIRCASE, STILT & FLAT INTERNAL REPAIR AREA:Providing and applying Two coats of wall care Putty as requireed thickenss as per the site conditions on plastered surface of Ceiling and Walls to prepare surface smooth of approved make, etc complete.as per the direction and approval of Consulting Engineer In-charge. |
| 42 | REMOVING OLD PAINT FROM STEEL:Removing old paint from steel and other metal surfaces and making the surfaces with hand scrappingetc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 43 | OIL PAINT ON OLD/NEW STEEL:Providing and applying first single coat of approved primer and two coats of synthetic enamel paint/flat oil paint of an approved make and colour as per manufacturers specifications to the steel surfaces at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 44 | INTERNAL RENOVATION OF FLATS |
| 45 | REMOVAL OF EXISTING CEMENT PLASTER:-Dismantling/ Removal of the existing old plaster (both internal and external) of any thickness and at all levels by chisel & hammer / cutter plate or skirting including raking out joints and cleaning the surface for re-plaster. Rates quoted to include removing all debris, spalls, including cleaning the site, lowering down the debris to the ground without causing dust nuisance and damage to the structure and carting away the debris outside the building compound upto the municipal dump with required municipal permision with all lead and lift. |
| 46 | BREAKING/CHIPPING LOOSE CONCRETE:-Chipping and removing theloose/ unsound/ weak concrete with manual chisel and/ or by standrad power driven percussion type of approved make equipment upto reinforcing bars, without removing the reinforcement, including tapering of all edges, making square shoulders of cavities, removing all the loose materials, cleaning the surface by water jet pressure pump to make all the exposed surface free from dust, oil and all impurities, etc. and air drying the surface, etc. complete as directed for all locations. (Note:-Exposed Surface area prepared for repair of structural member shall be considered for payment)Only the damaged area of concrete will be measured. |
| 47 | REMOVAL OF EXISTING WATERPROOFING:Removing the existing waterproofing layer of the existing toilet / bath areawithout causing any damage to Brick-bets & any of the structural member throighlight weight chippermachine and cleaning the same of any loose material etc. complete as per the direction and approval of Consulting Engineer In-charge. |
| 48 | REMOVING OF TILES, MARBLE, GRANITE: Removing mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles, vitrified tiles of any thickness in flooring and dado including the bedding cement mortar or tile adhesive and removing all debris, spalls, including cleaning the site, lowering down the debris to the ground floor without casuding dust nuisance and damage to the structure and carting away the debris outside the building compound upto the municipal dump with required municipal permision with all lead and lift, etc. complete. |
| 49 | STRUCTURAL POLYMER REPAIR (UPTO 15mm THICKNESS):Repairing to the existing RCC structural members (vertical or horizontal) using ready mix Polymer Modified Mortar (Fibre reinforced structural grade repair mortar) of approved brand where the thickness of repair is upto 15 mm. It can be used for carrying out extensive repairs to beams, columns, slab, and other structural elements, repairing of structural members subjected to repetitive loading for strengthening. Procedure for carrying out repair Polymer Modified Mortar -Surface preparation- (separate payment shall be made ) All loose traces of concrete or mortar, dust, grease oil, etc. must be removed. Damaged or contaminated concrete shall be removed to obtain a keyed aggregate exposed surface. Non-impact/ vibrating cleaning methods, e.g. grit or high pressure water blasting are recommended. Clean all exposed reinforcement to a minimum grade of Sa 2 according to ISO 8501-1 / ISO 2944-4. Ensure all visible portions of the reinforcing bar is clean. Where reinforcing bars are corroded, cut back the concrete around the reinforcing bars, Grit blast to remove corrosion products from around reinforcing bars and coat with approved epoxy coating for corrosion protection or any other protective coating as recommended by the Structural Engineer to protect from corrosion. Replace the affected part of rebar if the diameter after grit blasting is found reduced by more than 20% of the original diameter on the advice of the structural engineer responsible for the works. Bond Coat- (separate payment shall be made only for bond coat used for old surface to new surface) Providing & applying One coat of structural grade epoxy bond coat by brush conforming to ASTM-C-882-87 to the prepared concrete surface to be repaired / strengthened and repairingwith PMM shall be done when the surface is tacky. Mixing -Only full bags are mixed. Damaged or opened bags should not be used. Mix the ready-mix Polymer Modified Mortar in a forced action pan mixer, or with a helical paddle attached to alow speed (300-600rpm) mixer for 3 minutes until a lump free, thixotropic consistency is achieved. Only use clean water. Mixing water needed: 3.75 to 4.25 litres per 25kg bag or as recommended by the Manufacturer of Polymer Modified Mortar. Allow the mortar to rest for 2 - 3 minutes and then nremix briefly before pouring into formwork. If temperature more than 40°C then use chilled water for mixing.Mortar application- The minimum temperatures must be maintained duringapplication and for at least 24 hours thereafter for optimumcuring of the product. The prepared substrate should be presoaked, preferably for 24 hours, but at least 2 hours beforeapplying Polymer Modified Mortar. The surface must besaturated surface dry, but without standing water. PolymerModified Mortar can be spray- or hand-applied. Apply mixedproduct directly to the prepared damp substrate, or wet on wetonto the primed surface. Spraying the material with the necessary pressure will ensure good adhesion o fthematerial.A thin scrape coatorcontac tlayer before building upto ther equired thickness, wet on wet, will improveadhesionespecially in case of hand application. Apply to the desiredlayer thickness upto 15 mm and level using a screeding bar,trowel or woodenboard. Smoothing with a trowel or finishingby float or sponge can be done as soon as the mortar hasbegun to stiffen.Protective coatings - Subsequent coatings of any anticarbonation barriers or silaneimpregnationsshouldbeapplieifrecommendedbytheStructural Engineer.Plaster- (No separate payment shall be made).The repaired surface shall be matched to the surroundingsurface by providing required thickness of plaster internal orexternal plaster.CuringMinimum 7 days curing shall be done to the newly repairedareausingany suitablemethodRequiredCompressivestrength(ASTC1097cmcube)ReadyMixPolymerModifiedMortar used on site shall besentfortestingofcompressivestrengthandminimumstrengthrequired to be achieved is as follows – 1 Day-15 MPa, 3 Day-25 MPa, 7 Day-35 MPa, 28 Day-45 MPa.Surface Coating -Providing surfsce coating of polymer after completion of structural repair work. |
| 50 | STRUCTURAL POLYMER REPAIR (From 15mm to 30mm THICKNESS): Repairing to the existing RCC structural members (vertical or horizontal) using ready mix Polymer Modified Mortar (Fibre einforced structural grade repair mortar) of approved brand where the thickness of repair is upto 30 mm in two layers. Itcan be used for carrying out extensive repairs to beams, columns, slab, and other structural elements, repairing of structural members subjected to repetitive loading for strengthening. Procedure for carrying out repair Polymer Modified Mortar - Surface preparation- (separate payment shall be made )All loose traces of concrete or mortar, dust, grease oil, etc.must be removed. Damaged or contaminated concrete shallbe removed to obtain a keyed aggregate exposed surface.Non-impact/ vibrating cleaning methods, e.g. grit or highpressure water blasting are recommended. Clean all exposedreinforcement to a minimum grade of Sa 2 according to ISO8501-1 / ISO 2944-4. Ensure all visible portions of thereinforcing bar is clean. Where reinforcing bars are corroded,cut back the concrete around the reinforcing bars, Grit blast toremove corrosion products from around reinforcing bars andcoat with approved epoxy coating for corrosion protection orany other protective coating as recommended by theStructural Engineer to protect from corrosion. Replace theaffected part of rebar if the diameter after grit blasting is foundreduced by more than 20% of the original diameter on theadvice of the structural engineer responsible for the works.Bond Coat- (separate payment shall be made only for bondcoat used for old surface to new surface)Providing & applying One coat of structural grade epoxy bondcoat by brush conforming to ASTM-C-882-87 to the preparedconcrete surface to be repaired / strengthened and repairingwith PMM shall be done when the surface is tacky.Mixing -Only full bags are mixed. Damaged or opened bags should notbe used. Mix the ready-mix Polymer Modified Mortar in aforced action pan mixer, or with a helical paddle attached to alow speed (300-600rpm) mixer for 3 minutes until a lump free,thixotropic consistency is achieved. Only usec leanwater.Mixing water needed: 3.75 to 4.25 litres per 25kg bagorasrecommendedManufacturerofPolymerModifiedMortar.Allowthemortar to rest for 2 - 3 minutes and thenremix briefly beforepouring into formwork. If temperature morethan 40°C then use chilled water for mixing.Mortar application-The minimum temperatures must be maintained duringapplication and for at least 24 hours thereafter foroptimumcuring of the product. The prepared substrate should be presoaked,preferably for 24 hours, but at least 2 hours beforeapplying Polymer Modified Mortar. The surface must besaturated surface dry, but without standing water. PolymerModified Mortar can be spray- or hand-applied. Apply mixedproduct directly to the prepared damp substrate, or wet on wetonto the primed surface. Spraying the material with thenecessary pressure will ensure good adhesion of the material.A thin scrape coat or contact layer before building uptotherequiredthickness,wetonwet,willimproveadhesionespeciallyincaseofhandapplication.Applytothedesiredlayerthickness upto 15 mm in single layer and after hardening,provide second layer of required thickness (total upto 30 mm)and level using a screeding bar, trowel or wooden board. Ifrequired, bond coat shall be provided as per therecommendation of manufacturer between two layers ofpolymer Modified Mortar and no separate payment shall bemade for it. (However, between old & new surface of concretebond coat shall be applied & paid separately) Smoothing witha trowel or finishing by float orsponge can be done as soon asthe mortar has begun to stiffen.Protective coatingsSubsequent coatings of any anticarbonation barriers or silaneimpregnationsshouldbeapplieifrecommendedbytheStructural Engineer.Plaster- ((No separatepaymentshallbe made))The repaired surface shall be matched to thesurroundingsurface by providing required thickness of plaster internal orexternal plaster.CuringMinimum 7 days curing shall be done to the newlyrepaired/jacketed area using any suitable method.Required Compressive strength (ASTM C109 7cm cube)Ready Mix Polymer Modified Mortar used on site shall be sentfor testing of compressive strength and minimum strengthrequired to be achieved is as follows – 1 Day-15 MPa, 3 Day-25 MPa, 7 Day-35 MPa, 28 Day-45 MPa. Surface Coating - Providing surfsce coating of polymer after completion of structural repair work. |
| 51 | GROUTING NIPPLE:Providing, drilling and fixing Nipples for pressure injection grouting of polymer cement grout etc. complete |
| 52 | INJECTION GROUTING:Providing Grouting by specially prepared grout of approved make chemical with cement in proportion 1:3.5 (1 part chemical & 3.5 part cement by weight) along with 50 ml super plasticizer non cracking antiwash high strength polymer cement grout P C grout available in bags or equivalent with proper water for injectable consistency and applying it in the body of structure like slab, beam, column, pillars, deckslab, retaining wall, basement, underground and elevated water storage reservoir concrete and brick wall, crack portion of structure etc. by injecting method, to achieve its original strength including drilling of suitable diameter drills holes at 2 to 4 Nos. per sqm. using caps and nozzle grouting machinery necessary, scaffolding, finishing and covering gurantee of 10 years on court stamp paper of Rs. 100/and necessary testing etc. complete. (Prior permission of S.E. in writing is necessary before inclusion of this item in estimate) |
| 53 | NEW REINFORCEMENT STEEL:Providing, fabricating, welding & fixing steel reinforcement (Fe500) in existing damaged reinforcement in RCC as required Dia of approved brand i.e. TATA/SAIL or equivalent. For column, beams & slab. Etc. including transporting the same to site, cutting, bending, tying at all heights and in all positions, providing concrete covers as required at any height etc. Rates to include MS/TS dowel pins /staple/shear pins including drilling holes in concrete and providing labour and materials for fixing the pins etc. Complete as per the direction of Consulting Engineer / in-charge. |
| 54 | M.S. STEEL PROPS:-Providing and erecting steel tubular props of required height upto 14\" feet, L head or flat head braced at center and supporting a continuous 2\" x 3\" wooden runner, resting on wedge and block minimum capacity 3 Ton to support the structure provisionally during repair and jacketing etc. and maintaining them in position till all required item are complete. The props are erected in perfect vertical in plumb taking / transferring the load equally / uniformly. The location of every prop should be one over another floor and it should not be eccentric. The tightening of every prop should be uniform to all props to strain the building uniformly, removing the same as per the direction of Consulting Engineer / in-charge complete. Payment will be made location wise and based on nos. of props. |
| 55 | MASONRY BRICK WALL: Brickwork with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor 7 level in all shapes and sizes in cement mortar 1:4 (1 cement : 4 coarse sand) |
| 56 | INTERNAL PLASTER:Providing and applying internal plaster in single coat in CM 1:4 including wall punning with plaster of paris (with plaster of paris material of Ambuja/Mor Chap or equivalent make) in 10 to 13 millimeter thickness to previously plastered surface/or on newly brick surface(Excluding rough cast plaster)in all position including preparing and Finishing the surface scaffolding etc.complete.Phaseof all repaired foundation shall be coated with DECKGAURD S (protective layer ) or approved equivalent mentioned in the tender document in 2 coats at the rate of 0.35 lt/ sq.m. |
| 57 | FLOORING TILES:-Providing and laying doublle charge vitrified stone effect finish tiles having size 590 to 605mm x 590 to 605 mm of 10 mm thickness of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curign and cleaning etc. complete. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 58 | SKIRTING TILES:Providing and laying double charge vitrified tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete |
| 59 | TOILET FLOORING TILES:Providingand laying Anti skid Ceramic tiles of approved quality of size 30cm x 30cm and confirming to IS15622-2006 (Group-BIIA) for anti skid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. |
| 60 | TOILET WALL TILES:Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with ready made adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. |
| 61 | TOILET WATERPROOFING :Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years\" guarantee on requisite stamp paper including curing etc. complete |
| 62 | WATERPROOF PLASTER FOR TOILET WALLS:Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram per bag of cement of approved makeand manufacturer and curingetc.complete. (Excluding Tiles) (As directed by Engineer in Charge) |
| 63 | EUROPEAN TYPE WC:Providing and fixing European type white glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the out side face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32mm dia. UPVC flush pipe with fittings and clamps, 20mm dia. UPV Cover flow pipe, mosquito proof couplings G.I.chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing etc.complete.(prior approval of sample and brand by Ex.Engineer is necessary before use) |
| 64 | WALL MIXER:Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia |
| 65 | SHOWER:Providing and fixing C.P. wall mixer with provision for over head shower with 115mm longbend pipe andwall flange of approvedmake including necessary sockets/union nutetc. complete |
| 66 | WASH BASIN:Providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black coloured granite of 180mm thick stone black kadappa frame work including chromium plated coupling bottle Trap using CERA company or equivalent oval typawash basinmodel no 3448 as per detailed drawing or asdirected by engg incharge etccomplete. (Counter size 1.20m x 0.60 m) |
| 67 | TWO-WAY BIB COCK:Providing and fixing C.P. 2Way BIB cock with wall flangeof approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. |
| 68 | STOP COCK:Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete. |
| 69 | PILLAR COCK:Providing and fixing C.P. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete. |
| 70 | NAHANI TRAP:Providing and fixing 10 cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete. |
| 71 | TOWEL RAIL:Providing and fixing 600 mm SS towel rail with SS screws and other required fittingsof approved quality and colour. |
| 72 | TOILET PAPER HOLDER:Providing and fixing JAQUAR MAKE,HOTELIER series Model No. 1551 Toilet Paper Holder Recessed type (S.Steel) including cutting and making goodthe wall wherever required etc complete. |
| 73 | MIRROR:Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357mm |
| 74 | ANGLE COCK:Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.15 mm nominal bore |
| 75 | SOAP DISH:Providing and fixing C.P.soap dish (polyurethane) jaquar make continental (Cat. No. AQN 7733 ) |
| 76 | WALL CARE PUTTY ON WALL & CEILING:Providing and applying Two coats of wall care Putty on plastered surface of Ceiling and Walls to prepare surface even and smooth of approved make, etc complete. |
| 77 | INTERNAL PLASTIC PAINT ( FLAT AREA ):Providing and applying first single coat of approved primer and two OR More coats of acrylic plastic emulsion paint of an approved make and colour as per manufacturers specifications to any surface, at all height and locations as directed including scaffolding, cleaning and preparing surfaces for painting by any approved means etc. complete as directed by Engineerin- charge. |
| 78 | MODULAR FURNITURE WARDROBE INCLUDING LOFT: WARDROBE- Providing, making & assembling Bedroom 1 Wardrobe 1900-1950 x 600 x 2100 mm in heightas per architectural drawing and instructions. The system shallcomprise with following:Ply Boxing - Providing, making and fixing 18mmthick commercial ply (IS 303) boxing (for Vertical & horizontal sides). Centrevertical portion shall be made of 2nos. 18mm thick sandwiched commercial ply (IS 303). 12mm commercial ply (IS 303) shall be fixed to the Wardrobe back work as per architectural drawing & instructions. Finished the wardrobe with 1mm thick approved white laminate (IS 2046-1969/1995)from inside and 1mm thick approved laminate (IS 2046-1969/1995) from out side at visible side and hidden surface shall be finished with french polish as per drawing. Wardrobe Shutters- Providing & making 4 nos. equal wardrobe shutters 2100 mm high made out 25mm thick block board (IS 1659:2004) hungto the ply boxing with heavy duty ss hinges of approved make. Shutter shall be finished with 1mm thick approved laminate (IS 2046-1969/1995) from out side and 1mm thick approved white laminate (IS 2046-1969/1995)from inside. 12mm thick teak wood beading for shutter finished with approved melamine polish matching to the laminate (IS 2046-1969/1995) as per drawings. Drawers -Providing & fixing 4 Nos approx. 400 x 165 mm high Drawers to be made in 18 mm thick commercial ply (IS 303)front & side, back & bottom from 12 mm thick commercial ply (IS 303)drawer shall be finished with 1 mm thickapproved laminate (IS 2046-1969/1995) from out side and 1mm thick approved white laminate (IS 2046-1969/1995)from inside. Fixed the drawers to thewardrobe with telescope channels properly as per architectural drawings and as per specification and instruction. Rate also included providing, making & fixing 20mm thick fixed shelves ( 2 nos 850 x 600mm in size approximately) made of 18mm commercial ply(IS 303) finished with approved 1mm thick white laminate (IS 2046-1969/1995) at all sides. Rate also included p/f 8mm thick modi or equivalent make approved mirror on shutter as per architectural drawing including necessary hardware of approved make, necessary beads, mouldings, 75 mm high skirting, lipping, providing & fixing 25mm dia. 850 mm long 2no. SS pipe for hanger of approved make, providing & fixing 8 nos ss hooks of approved make completed as specified. LOFT - Providing, making & assembling Wardrobe Loft of 1950 x 600 x 550 mm in heightas per architectural drawing and instructions. The system shallcomprise with following:Ply Boxing for Loft - Providing, making and fixing 18mmthick commercial ply (IS 303) boxing (for Vertical & horizontal sides). Centrevertical portion shall be made of 2nos. 18mm thick sandwiched commercial ply (IS 303). 12mm commercial ply (IS 303) shall be fixed to the Wardrobe back work as per architectural drawing & instructions. Finished the wardrobe with 1mm thick approved white laminate (IS 2046-1969/1995)from inside and 1mm thick approved laminate (IS 2046-1969/1995) from out side at visible side and hidden surface shall be finished with french polish as per drawing. Loft Shutters- Providing & making 4 nos. equal shutters made out 25mm thick block board (IS 1659:2004) hungto the ply boxing with heavy duty ss hinges of approved make. Shutter shall be finished with 1mm thick approved laminate (IS 2046-1969/1995) from out side and 1mm thick approved white laminate (IS 2046-1969/1995)from inside. 12mm thick teak wood beading for shutter finished with approved melamine polish matching to the laminate (IS 2046-1969/1995) as per drawings and with all necessary fittings.Hardware fittings & Fixtures--a) SS finished Heavy duty \"L\" Hinges (75 x 19 x 6mm in size)- 16 nos. b) Concealed Lock- 2 nos. c)150 mm long SS Tower Bolt- 2nos. e)Heavy duty magnetic catch- 4 Nos. f) SS handle 300 mm long - 4 nos. g) Drawer lock - 4 nos. h) SS Hooks - 8Nos. . |
| 79 | MODULAR FURNITURE WARDROBE INCLUDING LOFT: Providing, making & assembling Bedroom 1 Wardrobe 1200-1250 x 600 x 2100 mm in heightas per architectural drawing and instructions. The system shallcomprise with following Ply Boxing - Providing, making and fixing 18mmthick commercial ply (IS 303) boxing (for Vertical & horizontal sides). Centrevertical portion shall be made of 2nos. 18mm thick sandwiched commercial ply (IS 303). 12mm commercial ply (IS 303) shall be fixed to the Wardrobe back work as per architectural drawing & instructions. Finished the wardrobe with 1mm thick approved white laminate (IS 2046-1969/1995)from inside and 1mm thick approved laminate (IS 2046-1969/1995) from out side at visible side and hidden surface shall be finished with french polish as per drawing. Wardrobe Shutters- Providing & making 4 nos. equal wardrobe shutters 2100 mm high made out 25mm thick block board (IS 1659:2004) hungto the ply boxing with heavy duty ss hinges of approved make. Shutter shall be finished with 1mm thick approved laminate (IS 2046-1969/1995) from out side and 1mm thick approved white laminate (IS 2046-1969/1995)from inside. 12mm thick teak wood beading for shutter finished with approved melamine polish matching to the laminate (IS 2046-1969/1995) as per drawings.Drawers -Providing & fixing 4 Nos 400 x 165 mm high Drawers to be made in 18 mm thick commercial ply (IS 303)front & side, back & bottom from 12 mm thick commercial ply (IS 303)drawer shall be finished with 1 mm thickapproved laminate (IS 2046-1969/1995) from out side and 1mm thick approved white laminate (IS 2046-1969/1995)from inside. Fixed the drawers to thewardrobe with telescope channels properly as per architectural drawings and as per specification and instruction. Rate also included providing, making & fixing 20mm thick fixed shelves ( 2 nos 850 x 600mm in size approx.) made of 18mm commercial ply(IS 303) finished with approved 1mm thick white laminate (IS 2046-1969/1995) at all sides. Rate also included p/f 8mm thick modi or equivalent make approved mirror on shutter as per architectural drawing including necessary hardware of approved make, necessary beads, mouldings, 75 mm high skirting, lipping, providing & fixing 25mm dia. 850 mm long 2no. SS pipe for hanger of approved make, providing & fixing 8 nos ss hooks of approved make completed as specified. LOFT - Providing, making & assembling Wardrobe Loft of 1250 x 600 x 550 mm in heightas per architectural drawing and instructions. The system shallcomprise with following:Ply Boxing for Loft - Providing, making and fixing 18mmthick commercial ply (IS 303) boxing (for Vertical & horizontal sides). Centrevertical portion shall be made of 2nos. 18mm thick sandwiched commercial ply (IS 303). 12mm commercial ply (IS 303) shall be fixed to the Wardrobe back work as per architectural drawing & instructions. Finished the wardrobe with 1mm thick approved white laminate (IS 2046-1969/1995)from inside and 1mm thick approved laminate (IS 2046-1969/1995) from out side at visible side and hidden surface shall be finished with french polish as per drawing. Loft Shutters- Providing & making 4 nos. equal shutters made out 25mm thick block board (IS 1659:2004) hungto the ply boxing with heavy duty ss hinges of approved make. Shutter shall be finished with 1mm thick approved laminate (IS 2046-1969/1995) from out side and 1mm thick approved white laminate (IS 2046-1969/1995)from inside. 12mm thick teak wood beading for shutter finished with approved melamine polish matching to the laminate (IS 2046-1969/1995) as per drawings and with all necessary fittings.Hardware fittings & Fixtures--a) SS finished Heavy duty \"L\" Hinges (75 x 19 x 6mm in size)- 16 nos. b) Concealed Lock- 2 nos. c)150 mm long SS Tower Bolt- 2nos. e)Heavy duty magnetic catch- 4 Nos. f) SS handle 300 mm long - 4 nos. g) Drawer lock - 4 nos. h) SS Hooks - 8Nos. . |
| 80 | KITCHEN PLATFORM: Providing andconstructing granite kitchenplatform withfixing of stainlesssteelsink 600 mm x 450mm size as per detaileddrawing including vertical bothside polishedkadappah stone 25 to 30 mm thick supports with kadappahtop 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two verticalgranitesupports15cmheightandtopgraniteof75x40cmincludingcutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m). |
| 81 | KITCHEN PLATFORM GRANITE: Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc., providing edge moulding and polishing of top and edges to give high gloss finish etc. complete at all levels. - Granite stone slab of colour black, Cherry/Ruby red with Area of slab over 0.50 sqm |
| 82 | MODULAR KITCHEN UNITS BOTTOM :Supplying pre-fabricated / factory made modular kitchen units below existing kitchen platform/counter ( approximately 750 mm in height and 700 mm in depth) as per the following specifications and enclosed sketch. The frame work of the cabinets including drawer fascia/ sides/bottom, shelves etc. shall be made out of 16 mm thick Marine plywood ( Century plywood, Kit Gold, Greenply, Western India Plywood, AEON or approved equivalent make). Shutters shall be made out of 16 mm thick Marine plywood (Century plywood, Kit Gold, Greenply, Western India. Each shutter shall be fixed to the framework using two numbers of best quality EURO type Slip/Auto Hinges (Ebco, Hettich, Hafele or approved equivalent make) and provided with one approved quality and profile brush finished Stainless Steel (SS) handle of grade 304 (minimum 150 mm long) Each drawer fascia shall be made out of 16 mm thick Marine plywood (Century plywood, Kit Gold, Greenply, Western India Plywood, AEON or approved equivalent make) and approved quality and make SS 304 grade baskets / accessories (Hettich, Ebco, Hafele or approved equivalent make) shall be mounted on approved quality, high precision telescopic channels/slides (Ebco, Hettich, Hafele or approved equivalent make) to be designed as per drawer size and to meet the weight requirement with minimum length of 500 mm to ensure smooth movements of drawer with /without content weightsand provided with approved quality 150mm size SS handles of grade 304. The telescopic channel rails may be provided as per specifications. In each kitchen there should be a minimum of 1No. perforated Cutlery basket(4” size), 1 No. cup & saucer basket(6” size), 1 No. \"Thali\" basket(8” size), 4 Nos of plain multipurpose baskets(8” size), 1 No. three tier oil/masala ‘Pull out’, 1 No. 2 tier detergent ‘Pull out’, 1 No. shutters below the sink with bin holder(Dia 250mm, Height 145mm),1 No foldable shutter at the mid corner portion for gas cylinder & 2Nos plain shutters each at both wall 1 and wall 2. The shutters shall be of 1618mm Marine plywood fascia/ sides/bottom as required as per the drawings given.All the stainless steel baskets shall be of maximum size which can be accommodated in the respective space available inside each cabinets for smooth functioning of railing. The Stainless Steel rods provided in the baskets shall be of combination of 5.5mm dia and 2.8mm dia rods and the spacing of these various steel rods in the baskets shall not be less than that of the samples\" baskets available with the Bank(Tenderers are advised to view the baskets available with the bank before quoting rate). All shelves shall be supported on approved quality Stainless Steel(SS) pins and shall be adjustable for various height requirements. The unit shall be firmly fixed to the walls/slabs/floor using non-corrossive metal screws of appropriate size and rawl plugs. All exposed surfaces and internal surfaces of the units shall havemachine pressed lamination having thickness 1mm and 0.8mm respectively of approved shade and make (Merino, Greenlam or approved equivalent) and pasted withsynthetic resin based adhesive (Fevicol, Vamicol or approved equivalent) etc. The thickness of four edge PVC lipping for shutters and drawer fascia shall be 2mm thick, thickness of edge lipping of carcass/ plywood partition should be 0.8mmand thickness of four edge lipping around the rebate of glass shutter shall be 0.6mm.The lippings/banding shall match with the external laminate shade. All faces and edges of Kadappahsupport slabs below the kitchen slab, wooden planks for supporting telescopic channel rails and wooden fillers shall be painted with a coat of synthetic enamel primer and two coats of white colour synthetic enamel paint. Payment shall be made on the basis of front elevation area of modular units only. It is clarified that sides, top and bottom surfaces will not be measured for payment. The wooden frame for shutter shall be made of minimum 70 mm wide marine plywood with lamination, wherever required. The telescopic channel shall be supported with 75 mm wide vertical and horizontal marine plywood members with laminate fixed on vertical Kadaph stone. If there is a need of erecting additional vertical marine plywood members with laminate on account of site conditions, the quoted rate shall have provision of carrying out these works. All necessary hardwares, wooden members with required thickness for fixing telescopic channel rails and filling the gaps shall be included in the quoted rate. The quoted rate shall include making of vertical partition below the existing kitchen slab with 16 mm thick marine plywood if necessary to accommodate modular kitchen units as per the requirement. |
| 83 | KITCHEN PLATFORM TOP CABINET UNITS :Supplying of pre-fabricated / factory made Over head kitchen cabinet units of 600 mm in high and 300 mm in depth as per the following specifications and enclosed sketch. The frame work or carcass of the cabinets, its sides/bottom, shelves etc. shall be made out of 16 mm thick Marine plywood (Century plywood, Kit Gold, Greenply, Western India Plywood, AEON or approved equivalent make). Glazed shutters ofcabinets as per the drawing shall be made out of 16 mm thick Marine plywood (Century plywood, Kit Gold, Greenply, WIP,AEON or approved equivalent make). Each shutter shall be fixed to the framework /carcass by using two numbers of best quality EURO type Slip/Auto Hinges (Ebco, Hettich, hafele or approved equivalent make) and provided with an approved quality and profile brush finished SS handle (minimum 150 mm long) of 304 grade. The glazed shutters shall have 5mm thick float glass fitted in 16 mm thick marine plywood frame alround with necessary cleats, clips and magnetic catchers. There will be one glass shelf of 10 mm thick edge polished float glass for horizontal partition in each cabinet. The thickness of four edge PVC lipping for shutters shall be 2mm thick, thickness of edge lipping of carcass/ plywoodpartition should be 0.8mmand thickness of four edge lipping around the rebate of glass shutter shall be 0.6mm.The lippings/banding shall match with the external laminate shade. All shelves shall be supported on approved quality SS pins and shall be adjustable for various height requirements. The over head cabinet carcass shall be fitted to the wall with PVC capped 2mm thick concealed MS hanging brackets each having width of 15mm and depth of 50mm @ 2 brackets for each cabinet which is fixed on wall with necessary screws. All exposed surfaces and internal surfaces of the units shall havemachine pressed lamination having thickness 1mm and 0.8mm respectively of approved shade(Merino, Greenlam or approved equivalent) and pasted withsynthetic resin based adhesive (Fevicol, Vamicol or approved equivalent) etc.Measurement will be taken on the basis of front length and height of overhead cabinet units. It is clarified that sides, top and bottom surfaces will not be measured for payment. All necessary hardwares, wooden members for filling the gaps etc shall be included in the quoted rate. 3 Supplying wooden shutters for the existing vertical storage space at the wall 3 top side in the kitchen with 6 shutters; eachwith two auto hinges and one brush finished SS handle ( minimum size 150 mm ) and as per details below :Supplying wooden shutters for the existing vertical storage space at the wall 3 top side in the kitchen with 6 shutters; eachwith two auto hinges and one brush finished SS handle ( minimum size 150 mm ) and as per details below : Shutters as per the sketch shall be made out of 16 mm thick Marine plywood (Century plywood, Kit Gold, Greenply, WIP,AEON or approved equivalent make). Each shutter shall be fixed to the wooden framework by using two numbers of best quality EURO type Slip/Auto Hinges (Ebco, Hettich, hafele or approved equivalent make) and provided with an approved quality and profile brush finished SS handle (minimum 150 mm long) of 304 grade. The thickness of four edge PVC lipping for shutters and drawer fascia shall be 2mm thick with shade matching with the external laminate. All exposed surfaces and internal surfaces of the units shall havemachine pressed lamination having thickness 1mm and 0.8mm respectively of approved shade and make(Merino, Greenlam or approved equivalent) and pasted withsynthetic resin based adhesive (Fevicol, Vamicol or approved equivalent) etc. Measurement will be taken on the basis of front length and height of wooden shutters only. All necessary hardwares, wooden members filling the gaps shall be included in the quoted rate. |
| 84 | KITCHEN SINK:Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required, etc. complete as per the directions of the Engineer-in-Charge - Kitchen sink with drain board of size 510 x 1040 mm and bowl depth 250 mm |
| 85 | KITCHEN SINK COCK :Providing and fixingsink cock with regular swinging spout (Wall / floor Mounted Model) with wall flange having flow rate up to6.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalentmake incluidng other necessary fitting, etc. complete as directed by Engineer in charge.( Make shall conform to manufacturer\"s Green product and shall got approved from the Engineer In Charge.) |
| 86 | DOOR FRAME: Providing second class teak wooden frames of approved sizes for doors, windows, ventilators, clerestory windows and other frames, including fixing the frame in position by providing 40 x 5 mm flat iron hold fast lugs of 400 mm long and fixing the hold fast to the frames with 10 mm diameter bolts, nuts and wooden plugs and embedding embedding in cement concrete block 300x100x150 mm 1:3:6 mix or with dash fasteners of required dia & length or with suitable anchor fasteners of approved size and length, all moulding, rebating, jointing and finishing with 3 coats of French polish or one coat of primer and synthetic enamel paint in two coats, etc. complete as directed and specified by the Engineer-in-Charge |
| 87 | DOOR SHUTTER 35 MM: Providing and fixing 35 mm thick ISI marked flush door shutters of approved make conforming to IS : 2202 (Part I) with core of block board construction with frame of 1st class hard wood and well matched teak with decorative type 3 ply veneering with vertical grains or cross bands and face veneers on one side and non-decorative type 3 ply veneering with vertical grains or cross bands and face veneers on another side including fixing to the frames with required nos of stainless steelbutt hinges conforming with IS 12817 of size 125 x 64 x 2.50 mm with necessary SS screws andlipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters, etc. complete as directed by Engineer in charge. |
| 88 | DOOR SHUTTER 30MM: Providing and fixing 30 mm thick ISI marked flush door shutters of approved make conforming to IS : 2202 (Part I) with core of block board construction with frame of 1st class hard wood and well matched teak with non- decorative type 3 ply veneering with vertical grains or cross bands and face veneers on both the faces of the shutter including fixing to the frames with required nos of stainless steelbutt hinges conforming with IS 12817 of size 125 x 64 x 2.50 mm with necessary SS screws andlipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters, etc. complete as directed by Engineer in charge. |
| 89 | Providing and applying white cement based putty of approved brand and manufacture of average thickness of 2 mm or more in two coats, over the door shutters and preparing the surface even and smooth complete including cleaning and preparing surface for painting, etc. to the satisfaction of the Engineer-in-Charge. |
| 90 | Painting with two coats of synthetic enamel paint of approved brand and manufacture of required colour to give an even shadeincluding one coat of approved primer, scaffolding, cleaning, preparing the surface for painting by approved means, applying additional coats wherever required to achieve even shade and colour, etc. complete as directed by the Engineer-in-Charge. |
| 91 | Providing and applying two or more coats of french spirit polishing of approved brand and manufacturer including a coat of wood filler inlcuding preparing the surface for painting by approved means, applying additional coats wherever required to achieve even shade and colour, etc. complete as directed by the Engineer-in-Charge. |
| 92 | Providing and fixing 125 mm long chromium plated brass handles for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete |
| 93 | Providing and fixing 300 mm long Stainless Steel aldrops set made of 16mm diameter bars for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete |
| 94 | Providing and fixing Stainless Steel hanging type door stopper set for doors with necessary materials and fixtures like screws etc. and all labour etc. complete |
| 95 | Providing and fixing 250 x 10 mm bright finished brass tower bolts (barrel type) for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete |
| 96 | Providing and fixing 100 x 10 mm bright finished brass tower bolts (barrel type) for doors and windows and with necessary materials and fixtures like screws etc. and all labour etc. complete |
| 97 | Providing and fixing Stainless Steel with chromium plated peep holes, manufactured as per IS, for doors with necessary materials and fixtures like screws etc. and all labour etc. complete |
| 98 | Providing and fixing type-2 (reversible latch) single side key operated rim locks along with the set of three keys manufactured as per best engineering practice of approved brands condorming to IS 9131 having 1 no. of deadbolt with double turn and 1 latch bolt for strong locking and safety locking/ unlocking from the inside with knob turn mechanism for main doors with necessary mounting accessories, materials and fixtures like screws etc. and all labour etc. complete |
| 99 | Providing and fixing Fiber Glass Reinforced plastic (FRP) DoorFrames of cross-section 90mm x 45mm having rebates of 32mm x15mm size to receive shutter of 30mm thickness. The laminate shallbe moulded with fire resistant grade unsaturated polyester resin andchopped mat. Door frame laminate shall be 2mm thick and shall befilled with suitable wooden block in the frame. The frame shall becovered with fiberglass from all sides. M.S. stay shall be provided atthe bottom to steady the frame etc. complete as directed. |
| 100 | Providing and fixing to frames 30 mm thick Fibre Glass Reinforced Plastic (FRP) panelled / extruded profiled door shutter of approved colour, brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels conforming to IS: 14856 - 2000 etc complete as directed. |
| 101 | CURTAIN ROD: Providing and fixing 25 mm dia chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., complete as directed and specified by the Engineer-in-Charge |
| 102 | WINDOW FRAME:Providingandfixingmarbleof18to20mm thich and approved colourfordoorframe/dado/window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing,etc. complete. |
| 103 | Providing and fixing Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)works for frames and shutters of doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, including fixing with dash fasteners of required dia and size, necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, providing and fixing hinges/ pivots and fittings wherever required including the cost of required EPDM rubber / neoprene gasket, etc.The Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required inluding cleat angles, aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, etc. all complete as per architectural drawings and the directions of Engineer-in-charge. etc. (Glazing will be paid for separately) |
| 104 | Providing and fixing Fly proof stainless steel grade 304 wire gauge/mesh with 0.5 mm dia. wire and 1.4 mm wide aperture in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . |
| 105 | Providing and fixing glazing with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . |
| 106 | MS GRILL:Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre asperdrawing including fixtures,necessarywelding andpainting withone coatsof anticorrosive paint and two coats of oil painting complete. |
| 107 | Dismantlingofexisting electricalmaterial in one flat i.e wiring,switches,sockets, Boards, PVC casing MCB\"s & DB\"s, ceilingfans,fittingsetcincluding disconnection and stacking of material in suitable place as per direction of Engineer-in Charge. |
| 108 | Wiringforlightpoint/fanpoint/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit(including), with modular switch, modularplate,suitableGIboxand earthingthepointwith1.5sq.mm FRLS PVC insulated copper conductorsinglecorecableetc.as required. |
| 109 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor,singlecorecableinthe existing surface/ recessed steel/ PVC conduit as required: 2 x 1.5 sq. mm |
| 110 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor,singlecorecableinthe existing surface/ recessed steel/ PVC conduit as required: 3 x 1.5 sq.mm |
| 111 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor,singlecorecableinthe existing surface/ recessed steel/ PVC conduit as required: 6 x 1.5 sq.mm |
| 112 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor,singlecorecableinthe existing surface/ recessed steel/ PVC conduit as required: 2 x 2.5 sq. mm |
| 113 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor,singlecorecableinthe existing surface/ recessed steel/ PVC conduit as required: 2 x 4 sq. mm |
| 114 | CONDUITING: Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required: 20 MM |
| 115 | CONDUITING: Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required: 25 MM |
| 116 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required: 12 Module Box |
| 117 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required: 6 Module Box |
| 118 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required: 3 Module Box |
| 119 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required: 2 Module Box |
| 120 | Supplyingandfixingfollowing modularswitch/socketon the existing modular plate & switch box including connections but excluding modular plate etc. as required.: 5/6 A switch |
| 121 | Supplyingandfixingfollowing modularswitch/socketon the existing modular plate & switch box including connections but excluding modular plate etc. as required.: 3 Pin 5/6 A Socket |
| 122 | Supplyingandfixingfollowing modularswitch/socketon the existing modular plate & switch box including connections but excluding modular plate etc. as required.: 6 Pin 15/16 A Socket |
| 123 | Providing and Fixing of Blank Dummy Swith |
| 124 | TELEPHONE SOCKET: Supplying and fixing Telephone socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 125 | TV SOCKET: Supplying and fixing TV socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 126 | TV CABLE: Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required |
| 127 | LED LIGHT:Supplying,installation,Testing& Commissioning of 30W Suspended/SurfaceMounted1x4ft LED Ceiling Light with White PowdercoatedCRCAHousing, lumenoutput notlessthan100 lm/watt,CCTnotlessthan5700K, CRI>80, PF>0.90 , & operating 230Volt 50Hz Power Supply i/c connectionwith3core1sqmm FRLS cu conductor etc complete as required. |
| 128 | FAN: Supply, Installation, Testing and Commissioningof1200mm sweep, BEE 5 star rated, ceiling fan with Brush LessDirect Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cmlongdownrod,2nos.canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value(CMM/W)minimum6.85,Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD lessthan10%,remoteorelectronic regulator unit for speed control and all remainingaccessoriesincludingsafety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase ACSupply,earthingetc.completeas required. |
| 129 | DISTRIBUTION BOARD (DBs):Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator): 12 way , Double door |
| 130 | MCB:Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required: Single pole |
| 131 | MCB:Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required: Double pole |
| 132 | RCCB: Supplying and fixing of following rating, double pole (single phase and neutral) 240V residual current circuit breaker (RCCB) having a sensitivity of 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required:40 A Rating |
| 133 | SUPPLY AND INSTALLATION OF CHIMNEY FOR KITCHEN: 60 CM wall mount filterless autocleaning with oil collection tray with suction capacity of 1500 cum/hr, curved SS/glass body, touch control, with necessary ducting, with 5 years comprehensive warranty |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
