|
| 1 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundation, manholes cesspits, shafts and for laying of underground cable and getting out in any type of soil complete all as directed by the Engineer-in-Charge |
| 2 | M&L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm in all kinds of soil complete all as specified and as directed. |
| 3 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. |
| 4 | M&L for providing PCC 1:2:4 type B-0 as in roof kerbs or mud stops rounded or chamfered on edges, saucer drain (using 12.5mm graded stone aggregate) complete all as specified and directed. |
| 5 | M&L for PCC 1:3:6 type C-1(using 20mm graded stone agg) for bed block for fixing hold fast complete all as specified and directed. |
| 6 | M&L for RCC Type B1 1:2:4 (using 20mm aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 7 | Supply only WPC complete all as specified and directed. |
| 8 | M&L for brick work with sub class `B’ bricks, straight on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed. |
| 9 | M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed. |
| 10 | S&F plain framed solid, chowkhats and frames, wrought rebated on solid rounded or chamfered put together with glue pinned supplied and fixed 2nd class hard woodcomplete all as specified and as directed. |
| 11 | S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 12 | Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete. |
| 13 | All asper item no 12here-in-before but exc 1.50 sqm but n.exc 4.00sqm each. |
| 14 | S&F Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Clustery window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rick husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 15 | S&F Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 30 mm thickcomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hingesshall be paid separately complete all as specified and directed. |
| 16 | S & F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed. |
| 17 | S & F 200 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed. |
| 18 | S&F Aluminium alloy, anodised, sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extruded sections or cast aluminium alloy and fixed 200 mm long complete. |
| 19 | S&F Aluminium alloy, anodised, sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extruded sections or cast aluminium alloy and fixed 300 mm long complete. |
| 20 | Supply & fixing butt hinges medium weight (SS) stainless steel of 100mm long complete all as specified and directed. |
| 21 | S & F aluminium handle, cast type anodized 150mm size. |
| 22 | Supply & fixing tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges all as specified. |
| 23 | S&F mild steel wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium staple and around all beading complete all as specified and as directed |
| 24 | S&F framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard; barred iron doors; ladders; framed balusters; walk ways; railing and similar work Con-forming to Fe 290 Gde E-165. |
| 25 | M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts,if required: hooks (stay),heavy,for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securingpurlinstowood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specifiedf and as directed. |
| 26 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. |
| 27 | M&L Rolled sections channel angle Tee section and in tubular section as in main and cross beams, hip and jack rafters; purlins, post where connected to common rafters and running rails and embedded in concrete complete. |
| 28 | Supply & fixing Steel windows with side hung shutters including box type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 29 | All as per item No.28 herein before but without glazing bars complete all as specified. |
| 30 | Supply & fixing steel ventilators with top hung shutters including hinges steel peg stay complete all as specified and directed. |
| 31 | S&F powder coated Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified. |
| 32 | S&F powder coated aluminium windows and ventilator shutters, side hung type without sash, aluminium sections weighing 0.55 Kg/m including necessary jointing cleat, glazing clips, rubber packing anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (01 Nos) hinges type B-21 100mm long (2 Nos) suitable handles (1 No) complete all as specified and as directed. |
| 33 | S&F Anodised aluminium snap grid frame work for false ceiling of grid size 605mm x 605mm complete all as specified and directed |
| 34 | S&F corrugated pre-painted aluminium zinc steel sheet (galvalumebase) or thickness0.50mmhaving tensile strength of 550 MPA , in colour and to be factory moulded as in roof covering /cladding and fixed withself-tapping screws /self-drilling screws, to suit the roofing in customizedcolour matching with the colour of roofing and screws are to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified. |
| 35 | S&F plain prepainted aluminium zinc steel sheet (galvalumebase) or thickness0.50mmhaving tensile strength of 550 MPA , in colour and to be factory moulded as in roof covering /cladding and fixed withself-tapping screws /self-drilling screws, to suit the roofing in customizedcolour matching with the colour of roofing and screws are to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified. |
| 36 | S & F 4mm thick non- asbestos E-board cement building board for insulation and acoustic purpose, 600 x 600 mm size fixed with staples on snap grid as in ceiling complete all as specified and directed. |
| 37 | M&L for 0.9mm thick decorative laminate type 1 of surface finish, colour and patters as approved, fixed with approved adhesive as per manufacturer\"s instructions, complete all as specified. |
| 38 | M & L for Machine cut, mirror polished Kota stone slab flooring 18-20mm thick over and including cement screed base 15mm thick in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 39 | M & L for Machine cut, mirror polished Kota stone 18-20mm thick in steps, riser, skirting, dado and pillar over and including cement screed base 10mm thick in cement mortar 1:4, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 40 | M&L for 75mm thick cement concrete 1:3:6 type C-2 using 20mm graded agg as in plinth protection including all necessary form work & finishing surface even & smooth using extra cement complete all as specified and as directed. |
| 41 | M&L for 75mm thick cement concrete 1:4:8 type D-2 using 20mm graded agg as in sub base finishing surface even and rough complete all as specified and as directed. |
| 42 | M&L Glazed coloured ceramic tiles in vertical surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match with back coat of screed bed or bedding layer 15mm thick 1:4 and pointed in white or coloured cement to match complete all as specified. |
| 43 | M&L Joint free non-skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:4 and pointed in white or coloured cement to match complete. |
| 44 | Dismantling floor, hearth, wall tiling including taking down plastering in cement mortar removing serviceable tiles to store and rubbish off the premises |
| 45 | Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturer’s instructions and finishing the surface even and smooth (without using extra cement) etc. complete all as specified. |
| 46 | Material and labour for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per manufacturer’s instructions and finishing the surface even and smooth (without using extra cement) etc.complete all as specified NOTE -WPC shall be measured and paid separately. |
| 47 | Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc complete. |
| 48 | M&L Preparing new plastered or un-plastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & including a coat of primer complete. |
| 49 | Material & Labour preparation of newly plastered surfaces of wall and applying a layer of wall care putty 2mm thick (averaging in two layer) on wall surfaces including cornices etc for proper levelling of plaster and applying two coats of exterior emulsion paint over a priming coat (as per manufacturers instruction) including all preparation complete all as specified and directed |
| 50 | S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete. |
| 51 | S&F Sheet glass 4.8mm thick tinted glass and glazing in squares complete. |
| 52 | M&L preparation wood Surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on newly prepared wooden surfaces complete all as specified and directed. |
| 53 | M&L for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer on steel surfaces over 10cm width or girth including preparation of surface complete. |
| 54 | Supply and Laying Steel Water Tubing 15mm dia (Bore), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed. |
| 55 | All as per Item No. 54 here–in–before, but for 20mm dia (Bore). |
| 56 | All as per Item No. 54 here–in–before, but for 25mm dia (Bore). |
| 57 | Taking up or down GI Water Tubing 15mm dia (bore) including Connections and Fittings, segregating serviceable Pipes & Fittings and Stacking properly at Site(s) for re-use, complete all as specified and as directed. |
| 58 | All as per Item No. 57 here–in–before, but for 20mm dia (Bore). |
| 59 | All as per Item No. 57 here–in–before, but for 25mm dia (Bore). |
| 60 | Dismantling water tanks of capacity n exc 500 ltr capacity complete including removing and lowring down from roof etc. complete all as specified and as directed. |
| 61 | S&F rotational moulded polythene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position 500 ltrs capacity with and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high-density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed. |
| 62 | S&F in repair 15mm dia bib taps CP Brass with Capstan head, screwed down, screwed for iron pipe of bore 15mm complete. |
| 63 | S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified. |
| 64 | S&F in repair Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 65 | S&F 15mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified. |
| 66 | S&F Gate valve 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 67 | S & F Stainless Steel grating 125mm dia complete all as specified. |
| 68 | S&F PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed. |
| 69 | Supply & fixing in repair 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed including necessary fittings like socket, bend, elbow, single/double tee etc in any length with rubber ring joints in any length with rubber ring joints, laid in trenches or in floors and making good with cement mortar 1:3 or with PCC 1:2:4 complete all as specified and directed. |
| 70 | Supply & fixing in repair 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed including necessary fittings like socket, bend, elbow, single/double tee etc in any length with rubber ring joints fixed with clamps of flat iron and including bolts and nuts and securing ends of stays to wall or roof and making good with cement mortar 1:3 or with PCC 1:2:4 including two coats of cement base paint /colour wash complete all as specified and directed. |
| 71 | M&L for cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes of 160mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed. |
| 72 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white/coloured (including fixing bolts & flush pipe, plastic water closet seat, black, closed pattern with bottom, and cover and mild steel chromium plated or aluminised hinging device etc.) complete all as specified and directed by Engineer-in-Charge |
| 73 | S& F vitreous china wash basin, white, flat back, size 550mm x 400mm, including brackets, PVC waste pipe 32mm dia, waste coupling brass, chromium plated and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs complete all as specified and directed. |
| 74 | Supply& Fixing Soap Dish CP Brass complete all as specified & directed. |
| 75 | Supply & fixing PVC Flushing Cistern 10 litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS brackets, CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed. |
| 76 | S& F 600x 450mm bevelled edge mirror or selected quality glass mounted on 6mm thick AC bldg board or commercial plywood and fixed to wooden plugs with CP brass screws and cup washers complete all as specified and as directed. |
| 77 | S&F Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium plated bracket guard and SS railing complete all as specified and as directed. |
| 78 | S&F Brass chromium plated shower rose 125mm size with shower arm, including fixing to steel pipe or union complete all as specified and directed. |
| 79 | Demolition of brick work built in cement work complete. |
| 80 | Demolition of cement concrete in ground floor and paving n.exc 15cm thickness (below or above ground level) complete all as specified and as directed. |
| 81 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete. |
| 82 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 83 | Dismantling timber scantlings 40sqcm and over in section of any description not otherwise provided for, in any position complete all as specified and as directed. |
| 84 | Dismantling asbestos cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified and as directed. |
| 85 | Dismantling plain or corrugated steel sheeting of any thickness in roof covering complete all as specified and as directed. |
| 86 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 87 | Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia 150mm, set in cement mortar complete. |
| 88 | M&L unplasticized PVC pipe 160mm dia type \"B\" with wall thickness 4mm (Min) of pressure rating 4 KN/Sqm laid in trenches and jointed with cement solvent including testing complete all as specified and directed. |
| 89 | S & F PVC floor tarps of size 75mm with grating including jointing to PVC pipe with lead joint all as specified and as directed. complete fixed in repair including making joint water tight. |
| 90 | Taking down carefully Aluminium/copper wiring of any size (for light, fan, socket or power etc complete) (fittings such as switches, sockets, ceiling roses, pendent holders’ regulators, tube lights etc to be measured and paid separately) and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed. |
| 91 | M & L point wiring for one light point/ fan/ bell/ 5Amps socket out let (independent) point controlled by one, one way switch with 1.5 sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FRLS)PVC cable drawn into & including medium grade PVC conduit (not less than 20mmouter dia) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) including metal flush box covered with 3mm thick plastic laminated sheet and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistrandedcopper conductor cable earth wire and connected to earth dolly complete all as specified and directed. |
| 92 | All as per item No. 91 here in before but for One modular socket outlet 3 pin 6 amps controlled by one switch on same board. |
| 93 | All as per item No. 91 here in before but for wiring with 2.5sqmm copper wire (FRLS) PVC and 2.5 sqmm earth wire for modular socket outlet 5 pin 16 amps on independent board. |
| 94 | S&F switch piano flush type single pole, one way 5 Amp complete all as specified and directed. |
| 95 | S&F socket out let 2 in 1 multi 3 pin, 5 Amps, flush type complete all as specified and directed. |
| 96 | S&F switch piano flush type single pole, one way 15 Amp complete all as specified and directed. |
| 97 | S&F socket out let 2 in1,6 pin, 5 and 15 Amp, flush type completes all as specified and directed. |
| 98 | S&F ceiling rose, PVC/ Poly carbonate, isolated body three terminal complete all as specified and directed. |
| 99 | S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed. |
| 100 | Supply and fix High quality LED light fitting 1x20 Watt (warm/milky white as required). 220V, AC decorative box type with driver, holder including LED tube light, internally pre wired of 1.5 sqmm twin twisted flexible copper cable, life of tube light not less than 50000 hours complete all as specified & directed. |
| 101 | S&F MCB SP, 240 volts, AC \"B\" curve, 10 KA 6 to 32 Amps complete with connection testing and commissioning all as specified and as directed. |
| 102 | S&F MCB SPN, 240 volts, AC \"C\" curve, 10 KA 40-63 Amps complete with connection testing and commissioning all as specified and as directed. |
| 103 | S&F sheet metal enclosure for DBs (double door type) single pole and neutral 8 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed. |
| 104 | S & F LED bulk head fitting, 1 x 10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed. |
| 105 | S & F Exhaust fan plastic body heavy duty ISI mark, 250 mm size with louvers including all connecting accessories and cutting opening on wall and making good as per existing surface complete all as specified and directed |
| 106 | Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 cores, including taking down old LT U/G cable from trenches/protection pipe etc. complete. |
| 107 | M & L for dry clean sand filling in trenches below and around under ground cable cushioning complete all as specified and as directed. Note:- Thickness of sand cushioning shall be measured after punning |
| 108 | Supply and fix unreinforced PCC cable cover class LV type I of size 250mmx150mmx40mm complete all as specified and as directed. |
| 109 | Supply and Fixing steel tube light grade galvanised 50mm bore with all fittings for protection of UG cable under road/ culvert and fixing on wall with saddle, screw complete all as specified and as directed. |
