|
| 1 | Material and labour for attending the emergent complaint and repairs to centrifugal monoblock pumpset of 30/40 HP including carrying out minor repairs etc as required to make the system in order/functional and necessary gland, rubber sheet, nuts, bolts, washers and phase sequence change, electric supply connections from switchgear/starter/panel etc complete all as specified and directed. |
| 2 | Material and labour for attending the emergent complaint and repairs to centrifugal monoblock pumpset of 3 HP to 12.5 HP including carrying out minor repairs etc as required to make the system in order/functional and necessary gland, rubber sheet, nuts, bolts, washers and phase sequence change, electric supply connections from switchgear/starter/panel etc complete all as specified and directed. |
| 3 | Material and labour for attending the emergent complaint and repairs to centrifugal monoblock pumpset, online booster pump, pressure pump, lifting pump of upto 2 HP including carrying out minor repairs etc as required to make the system in order/functional and necessary gland, rubber sheet, nuts, bolts, washers and phase sequence change, electric supply connections from switchgear/starter/panel etc complete all as specified and directed. |
| 4 | Taking down/up for repair centrifugal Pump sets from foundation, separating pump and motor, disconnecting the water and electric connnection and transporting to work shop, opening the pump for inspecting all parts to identify defective parts, cleaning/servicing & greasing including refixing and replacement unsv bearings for drive end and non drive end, gun metal bushes, impeller, shafts, shaft seal, worn out gland packing, gland nut bolt & replacement of damaged foundation bolts, reassembling of pumping set and transporting back to pump house, installing, connecting with water & electric connection and testing for performance for following capacities complete all as specified and directed. |
| 5 | (a) pump capacity upto 10 HP |
| 6 | (b) pump capacity 10 to 15 HP |
| 7 | (c) pump capacity 30 HP to 40.0 HP |
| 8 | Taking down/up for electric motor by disconnection from terminal & pump coupling & foundation complete removing of motor, carrying to workshop and return after opening motor removing burnt Copper wire, cleaning all parts throughly rewinding motor with same gauge and same No of turns of super enamelled Copper wire including insulating materials like varnishing, heating etc and replacement unsv ball bearings, terminal plate, foundation bolts and reassembling the electric motor by connecting with pump and electrical connections testing on completion of following capacities complete all as specified and directed. |
| 9 | (a) Motor capacity upto 10 HP |
| 10 | (b) Motor capacity 10 HP to 15 HP |
| 11 | (c) Motor capacity 30 HP to 40.0 HP |
| 12 | Taking out pumps alongwith motor from foundation, disconnecting the water and electric connection and transporting to work shop, opening the pump for inspecting all parts to identify defective parts, cleaning/servicing and greasing including replacement of unsv bearings for drive and non drive end, bushes, impeller, bearing, shafts, shaft seal, worn out gland packing and rewinding of electric motor by disconnection from terminal removing burnt Copper wire, cleaning all parts throughly rewinding motor with same gauge and same No of turns of super enamelled Copper wire including insulating materials like varnishing, heating etc and replacement unsv ball bearings, terminal plate, foundation bolts and reassembling the electric motor by connecting with pump and electrical connections testing on completion of following capacities ccomplete all as specified and directed. |
| 13 | (a) Pump set capacity 0.5/1/1.5 HP |
| 14 | (b) Pump set capacity upto 2/3/5 HP |
| 15 | (c) Pump set capacity upto 7.5 HP |
| 16 | (d) Pump set capacity upto 12.5 HP |
| 17 | Supply & fix in replacement of following sizes DOL starter in sheet metal enclosure complete all as specified and directed. |
| 18 | (a) 230 volts 50 Hz single phase for electric motor of capacity upto 2 HP |
| 19 | (b) 415 volts 50 Hz three phase for electric motor of capacity 3-5 HP |
| 20 | (c) 415 volts 50 Hz three phase for electric motor of capacity 7.5 HP |
| 21 | Supply & fix in replacement 415 volts 50 Hz three phase for electric motor of capacity 12.5 HP/15HP Fully automatic Star Delta Starter in sheet metal enclosure complete all as specified and directed. |
| 22 | M&L for disconnect the electric cable from panel and taking out the unserviceable/burnt out submersible Pump set of capacity upto 3.0/7.5 HP from the bore with the help of chain pully and tripod and transporting to work shop for carrying out rewinding the motor with same gauge and same no of turns of with water proof PVC insulated Copper wire of existing guage and size to achieve the specified/required RPM after taking out old unserviceable winding wire, cleaning/repairing damaged slots and also replacement of impellers, bearings, thrust bearings, gun metal bushes and NRV as per existings of pump, and installing/inserting back in position connecting up water and electric connections complete all as specified and directed. Note:-Supply only submersible cable & nylon rope etc will be measured paid separately. |
| 23 | Supply only in replacement for lowering the submersible Copper conductor multi stranded cable of size 3 core x 2.5 Sq mm with necessary connections from motor to starter complete all as specified and directed. |
| 24 | Supply only in replacement for lowering the submersible Copper conductor multi stranded cable of size 3 core x 4 Sq mm with necessary connections from motor to starter complete all as specified and directed. |
| 25 | Supply only in replacement nylon rope 8 and 12 mm dia with necessary locking arrangements complete all as specified and directed. |
| 26 | Material and labour for repairs/servicing to suction sweeper assembly of capacity upto 3 HP including replacement of unserviceable parts such as motors, wire brushes and replacing of axle with bearings including front and rear wheels, working handle, brush etc and painting with 2 coats of epoxy paint over a coat of epoxy primer complete all as specified and directed. |
| 27 | Supply only in replacement sucton sweeper plastic pipe of size 40mm dia good quality after removing from the suction sweeper complete all as specified & directed. |
| 28 | Comprehensive maintenance for filteration plant-03 nos at ASI Swimming Pool (outdoor ) (preventive, breakdown, Monthly, Quarterly, Half yearly maintenance). Taking out and removing existing sand, gravel, accumulated mud etc. from filter media form the pressure filters including cleaning of filter thoroughly inside etc and keeping safe custody in good condition of filter media as of different sizes as suitable for reuse and remaining unusable qty to be removed/disposal of to a distance not exceeding 100 Mtr complete including testing and commissioning complete all as specified & directed.Note : (a) Replacing the filter media such as sand, gravel and cleaning the gravels. Rejected gravels to be replaced with new gravels directed by Engineer-in-Charge which will be measured and paid for separately under relevant items. (b) Inspection/checking the pressure gauges, control valves including connecting pipes etc. damaged/corroded nuts bolts, arresting leakages by replacing gasket with new parts. Welding as required etc/deemed to be included quoted rates. (c) Testing and commissioning the plant complete all as specified and directed.complete. |
| 29 | Supply only Fresh nature river sand filter media 0.4 mm to 0.8 mm size complete |
| 30 | Supply only fresh gravel filter media in filter beds for the following sizes complete all as specified and directed. |
| 31 | (a) Fresh gravel filter media 25 mm to 50 mm |
| 32 | (b) Fresh gravel filter media 12 mm to 25 mm |
| 33 | (c) Fresh gravel filter media 03 mm to 12 mm |
| 34 | (d) Fresh gravel filter media 01 mm to 03 mm |
| 35 | Supply only TCCA-90 (TRICHLOROISOCYANURIC ACID) high strength chlorinator of opproved make for water disinfectant in factory sealed HDPE container (40 to 50 Kg each) complete all as specified and directed. |
| 36 | Supply only alum crystal free from impurity class I suitable for swimming pools complete all as specified and directed. |
| 37 | Supply only Copper sulphate in 40/50Kg packaging complete all as specified & directed. Note for item no. 18 to 20 : These items will be added to the swimming pool by DEL/M&O staff at the time of installations. |
| 38 | S&F in replacement cast Iron double flanged non-rising spindle type sluice valve having stainless steel to AISI 410 spindle & gun metal working parts, manually handwheel operated PN-1.6 with ISI marked, flange ends drilled complete all as specified and directed. |
| 39 | (a) 80mm dia |
| 40 | (b) 100mm dia |
| 41 | (c) 150mm dia |
| 42 | Supply and fixing in replacement cast Iron foot valve, ISI marked both end flanged with nut bolt washers and rubber gasket ISI marked, installation, testing of following sizes complete all as specified and directed. |
| 43 | (a) 80 mm dia. |
| 44 | (b) 100 mm dia |
| 45 | (c) 50 mm dia |
| 46 | (d) 200 mm dia |
| 47 | Supply and fix in replacement gun metal gate valve with Iron wheel head screwed both ends including dismantling the old unserviceable gate valve for Iron pipe of size complete all as specified and directed. |
| 48 | a) 15 mm bore |
| 49 | b) 20 mm bore |
| 50 | c) 25 mm bore |
| 51 | d) 40 mm bore |
| 52 | e) 50/65 mm bore |
| 53 | Supply and fix in replacement non return valve or reflex valve both end flanged ISI marked including making new flanged joints with 3 mm thick rubber gasket with necessary bolts, nuts, washer etc of suitable size of following size complete all as specified and directed |
| 54 | a) 50 mm bore |
| 55 | b) 80 mm bore |
| 56 | Maintenance and servicing of sluice valve, non return valve, foot valve of any size by disconnecting the water connnection opening the valves for inspection of all parts to identify defective parts, cleaning/servicing & greasing including refixing and replacement unserviceable parts, shafts, shaft seal, rubber washers, gates, rubber seal, worn out gland packing, gland nut bolt & replacement of damaged bolts, reassembling of valves, installing, connecting with water & electric connection and testing for performance complete all as specified and directed. |
| 57 | M&L in replacement connecting pieces one end flanged and other end socket or spigot and bell mouth pieces one end flanged other end tapering as bell mounth, CI bends tapers, tees, pieces (Single or double branch) any Type and angle/radius and straight connecting pieces for CI/GI/DI pipe upto 150 mm bore complete all as specified and directed. |
| 58 | M&L in replacement bends, tapers, tee pieces (single & double branch) any type and angle/radius and straight connecting pieces but all ends flanged any type and angle/radius and straight connecting pieces for CI/GI/DI pipe upto 150 mm bore complete all as specified and directed. |
| 59 | M&L for MS work for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated with including two coat of aluminum paint and coat of primer including dismantling of old unsviceable MS framed works complete all as specified and directed. Note: (i) Scaffolding, ladder etc for welding of MS ladder/angle for Semi UG sump/OH tank up to 20 Mtr to be arrange by the contractor. and the rates quoted by the contractor shall be deemed to be included for the above and nothing shall be paid extra on this account |
| 60 | M&L for construction of brick masonry valve pit, chamber one brick thick wall in cement mortar 1:4 on 100mm thick PCC 1:4:8 (using 40mm graded stone aggregate) in foundation, rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS sheet valve pit cover, welded with 40X5mm flat Iron frame alround including provision of hinges, handle and locking arrangement and 40 x 40 x 6mm angle Iron frame fixed on top of valve pit by means of holdfast 150mm long, embedded in PCC 1:2:4 (Type B1 using 20mm graded stone aggregates) block of size 230 x 200 x 100 mm including applying two coats of anti-corrosive paint over a coat of Red Oxide Zinc Chrome Primer after preparation of all exposed to Steel surfaces including necessary Earth work and excavation in soft/loose soil including demolition of old unserviceable valve pit of following sizes complete all as specified and directed. |
| 61 | (a) 600 x 600 x 600 mm (Internal Dimension) |
| 62 | (b) 900 x 900 x 900 mm (Internal Dimension) |
| 63 | (c) 1000 x 1000 x 1000 mm (Internal Dimension) |
| 64 | (d) 2000 x 2000 x 2000 mm (Internal Dimension) |
| 65 | M&L for preparing old painted surfaces pumps, motors, panels, pipes suction/delivery line by scraping and removing old paints, rust etc and painting with two coats of synthetic enamel paint complete all as specified and directed. |
| 66 | M&L for preparation of new or previously untreated steel surfaces over 10mm width or girth of any description, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 67 | Taking out all loose dirt, scales etc from the inner walls of under ground sumps by scraping with wire brush, cleaning with disinfectant chemicals, bleaching powder etc and providing two coats of white wash after preparing the surface thoroughly including writing date of cleaning of tank on outer side of walls for the following capacity of tank complete all as specified and directed.Note: (i) Scaffolding, brushes, bleaching powder, lime etc for cleaning the internal surface of under ground pump to be arrange by the contractor. and the rates quoted by the contractor shall be deemed to be included for the above and nothing shall be paid extra on this account (ii) Pumping arrangement for pumping out water below wash out shall be arrange by the contractor. |
| 68 | (a) 80000 ltrs at OLD NDA pump house |
| 69 | (b) 136000 ltrs at OLD NDA pump house |
| 70 | (c) 170000 litres at ASI pump House |
| 71 | Taking out all loose dirt scales etc from the inner walls of 1.2 lakh Gallons at OLD NDA complex pump house over head reservoir upto 20 metre high staging by scraping with wire brushes, cleaning with disinfectant chemicals, bleaching powder etc and providing two coats of whie wash after preparing the surface thoroughly including writing date of cleaning on outer side of walls for the sumps complete all as specified and directed.Note: (i) Scaffolding, ladder, brushes, bleaching powder, lime etc for cleaning the internal surface of under ground pump to be arrange by the contractor. and the rates quoted by the contractor shall be deemed to be included for the above and nothing shall be paid extra in this account (ii) Pumping arrangement for pumping out water below wash out shall be arrange by the contractor. |
| 72 | Surface dressing in soft/loose soil not exeeding 15 cm deep, across the pipe lines with including site clearance, cutting and cleaning of branches/bushes/plants/grass obstructing to the pipe lines/valves/chambers/sumps/OHTs on either sides and water supply Installation area including disposal of materials up to a distance not exceeding 50 mtr complete all as specified and directed. |
| 73 | M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in filling and mass concrete for foundation of pumps/motors/pipes including embedding necessary MS frame work/MS channel complete all as specified and directed. |
| 74 | M&L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 Mtr deep below normal ground level, with top edge of the plate vertically to a depth not less than 1.5 Mtr below ground level connected to and including GI strip 32 x 6 mm and GI pipe 40 mm dia light grade for protection upto the extent of 7.5 Mtr as earthing strip by means of GI bolts, nuts and washers etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Part-I including RCC cover with RCC 1:2:4 type B1 and MS angle Iron frame, watering arrangement with GI pipe 20 mm dia medium grade and MS funnel, concrete pit with including necessary excavation and earth work in any type of soil and testing on completion etc complete all as specified and directed.Note :-GI strip beyond 7.50 Mtr will be measured and paid separately. |
| 75 | S&F in replacement of old first aid box complete at various E/M installations complete all as specified and directed. |
| 76 | M&L for periodical checking of pumping sets complete, testing and adjusting all moving parts, lubricating, checking of alignment, checking of unusual sounds, heating, water leakages, etc complete all as specified and directed. |
| 77 | Supply & lay in replacement 15 mm dia GI pipe medium grade including all fittings fixed to walls/ceiling or laid in floors complete all as specified and directed. |
| 78 | Supply & lay in replacement 20 mm dia GI pipe medium grade including all fittings fixed to walls/ceiling or laid in floors complete all as specified and directed. |
| 79 | Supply & lay in replacement 25 mm dia GI pipe medium grade including all fittings fixed to walls/ceiling or laid in floors complete all as specified and directed. |
| 80 | Supply & lay in replacement 40 mm dia GI pipe medium grade including all fittings fixed walls/ceiling or laid in floors complete all as specified and directed. |
| 81 | Supply & lay in replacement 50 mm dia GI pipe medium grade including all fittings fixed walls/ceiling or laid in floors complete all as specified and directed. |
| 82 | Supply & lay in replacement 80 mm dia GI pipe galvanized, medium grade including all fittings fixed walls/ceiling or laid in floors complete all as specified and directed. |
| 83 | Supply & lay in replacement 100 mm dia GI pipe galvanized, medium grade including all fittings fixed walls/ceiling or laid in floors complete all as specified and directed. |
| 84 | M&L for LED sign board/display board etc on LED board minimum of size1.2m x 0.3 m, suitable for outdoor application, water proof, indoor brightness, auto/manual, can be viewed from long distance, high quality chip, without flickering, display ability like scrolling text, random text, numeric, date and time, animated text, long lasting, unbreakable, high brightnesss, scratch resistant and plug & ready to use, wall mounted, wIFI/bluetooth programming interface method, multi colour with all accessories and including wall mounting bracket of suitable size including clamps, nut bolts etc. including all accessories internally pre-wired and connecting up with twin core twisted flexible Copper conductor cable with suitable size complete all as specified and directed. |
| 85 | Material and labour for suction sweeper assembly of capacity upto 3 HP including parts such as motors, wire brushes and axle with bearings including front and rear wheels, working handle, brush etc and painting with 2 coats of epoxy paint over a coat of epoxy primer complete all as specified and directed. |
| 86 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 87 | M&L for 75 mm thick cement concrete 1:3:6, type C2, using 40 mm graded stone aggregate in floor/plinth protection finish the surface even and smooth without using extra cement including filling the expansion joints with bitumenfiller/filler boards complete all as specified and directed. |
| 88 | M&L for machine pressed precast concrete glossy interlocking Paver block any shape and size confirming to IS of 600 mm thickness M-35 grade with grey cement and pigment including 25 mm thick sand cushioning complete all as specified and directed. |
| 89 | Supply and fixing mechanical joint of made out of CI of thickness not less than 10 mm fabricated as per existing site requirement including long MS nut, bolt, rubber gasket, cutting/fixing of pipe in position of any size CI/GI/DI pipe with the help of manually as well as mechanical T&P including taking down old existing mechanical joint of following sizes :complete all as specified and directed. |
| 90 | (a) 40/50 mm bore dia |
| 91 | (b) 80/100 mm bore dia |
| 92 | (c) 150 mm bore dia |
| 93 | M&L for attending the emergency repairs to leakage/damage GI/UPVC/PPR pipe of size 20/25 mm dia including carrying out minor repairs to arrest the leakages all directed including necessary excavation, earth work, returning filling of excavated soil and removal of water by manually/mechanically and jointing with and including new fittings, accessories such as saddle clamp with rubber packing and nuts, bolts, washers etc union/sockets/tee/tee reducer etc as required basis complete all as specified and directed. |
| 94 | M&L for attending the emergency repairs to leakage/damage GI/UPVC/PPR pipe of size 40/50 mm dia including carrying out minor repairs to arrest the leakages all directed including necessary excavation, earth work, returning filling of excavated soil and removal of water by manually/mechanically and jointing with and including new fittings, accessories such as saddle clamp with rubber packing and nuts, bolts, washers etc union/sockets/tee/tee reducer etc as required basis complete all as specified and directed. |
| 95 | M&L for attending the emergency repairs to leakage/damage CI/GI/DI pipe of size 80/100 mm dia including carrying out minor repairs to arrest the leakages all directed including necessary excavation, earth work, returning filling of excavated soil and removal of water by manually/mechanically and jointing with and including new fittings, accessories such as saddle clamp with rubber packing and nuts, bolts, washers etc union/sockets/tee/tee reducer etc as required basis complete all as specified and directed. |
| 96 | M&L for attending the emergency repairs to leakage/damage CI/GI/DI pipe of size 150/200 mm dia including carrying out minor repairs to arrest the leakages all directed including necessary excavation, earth work, returning filling of excavated soil and removal of water by manually/mechanically and jointing with and including new fittings, accessories such as saddle clamp with rubber packing and nuts, bolts, washers etc union/sockets/tee/tee reducer etc as required basis complete all as specified and directed. |
| 97 | M&L for cutting existing CI/GI/DI tubing for alteration or additions of sizes including screwing existing GI tubing for arresting leakages, tapping or making new connections etc complete all as specified and directed. Note: excavation and earthwork will be measured and paid separately. |
| 98 | (a) 15 mm bore dia |
| 99 | (b) 20 mm bore dia |
| 100 | (c) 25 mm bore dia |
| 101 | (d) 40/50 mm bore dia |
| 102 | (e) 80/100/150 mm bore dia |
| 103 | Burning out unsv leakage lead joint in position, including removing old lead including necessary excavation and earth work in soils, returning, filling and removal of accumulated water by using pump of following sizes complete all as specified and directed. Note : (i) M&L Lead joint will be measured and paid separetly under respective items. |
| 104 | (a) 80 mm dia |
| 105 | (b) 100 mm dia |
| 106 | (c) 150 mm dia |
| 107 | M&L for run Lead joint in spigot and socket pipes and fittings of size 80 mm dia including necessary caulking the spun yarn as required complete all as specified and directed. |
| 108 | M&L for run Lead joint in spigot and socket pipes and fittings of size 100 mm dia including necessary caulking the spun yarn as required complete all as specified and directed. |
| 109 | M&L for run Lead joint in spigot and socket pipes and fittings of size 150 mm dia including necessary caulking the spun yarn as required complete all as specified and directed. |
| 110 | Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth and getting out in soft/loose soil for laying of pipe etc complete all as specified and directed. |
| 111 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soil complete all as specified and directed. |
| 112 | Removing excavated meterial (soil) to a distance not exc 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed. |
| 113 | Cutting of road/hard standing for taking out of unsviceable water pipe line and making new connection and making good with PCC (1:2:4) using 12.5mm graded stone aggregate including making good the disturbed portion to match the existing complete all as specified and directed. |
| 114 | M&L for running welding of thickness not exc 6 mm complete all as specified and directed. |
| 115 | Material and labour for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of old rusted surface of steel exc 10 cm width/grith, at any height of tank and water supply vertical pipes of pumping and distribution pipe lines as per different colour code including marking of arrow for flowing of water with approved color shade paint complete all as and directed. Note :-Scaffolding and connected allied items etc to be arranged by the contractor the rate quoted by the contractor shall be deemed to be included. |
| 116 | M&L for pipe support for all types of pipes including hangars/fastners/elbows/supports/tees complete all as specified and directed. |
| 117 | Supply and fix GI specials of following sizes complete all as specified and directed. |
| 118 | (a) 15mm dia elbow/socket/union/bend etc |
| 119 | (b) 20mm dia elbow/socket/union/bend etc |
| 120 | (c) 25mm dia elbow/socket/union/bend etc |
| 121 | (d) 40mm dia elbow/socket/union/bend etc |
| 122 | (e) 50mm dia elbow/socket/union/bend etc |
