|
| 1 | S&FStructuralsteelpostof angle iron 65x65x6mm, 4.50 Mtr long, weight as per IS 2062-1984 including fabrication of 0.60 Mtr both side long top portion swan neck V type at 30 degree to vertical, including making six round holes of 15 mm dia on vertical posts and for fixing of nuts and bolts and three Nos of 15 mm dia holes for fixing strut and five Nos notches on the swan neck and welding of two Nos of 16 mm MS rod each of 0.23 mtr length to bottom end of picket for anchorage including one coat of red oxide primer and two coat of synthetic enamel paintforexposedsurfaceof angle above GL complete and twocoatofbituminouspaint embedded portion of angle 0.45mtr. Make : Jindal/ SAIL/ TATA/Equivalent ISI Marked complete all as specified and directed by Engineer-in-Charge |
| 2 | S&F Structural steel post of angle iron 65x65x6mm, 3.30 Mtr long, weight as per IS 2065- 1984+B12, including fabrication for strut post bending at top portion, including making three Nos holes of 15 mm dia on vertical posts for fixing of nuts and bolts and three Nos of 15 mm dia including 0.23 mtr 16 mm dia MS rod two piece to be welded at bottom for anchoring purpose including one coat of red oxide primer and two coat of synthetic enamel paint for exposed surface of angle above GL complete and two coat of bituminous paint for stud 0.45mtr below GL for one side of the post complete all as specified and directed by Engineer-in-Charge. Make : Jindal/ SAIL/ TATA/Equivalent ISI Marked |
| 3 | S&F Galvanised two or three strand steel barbed wire (line wire) of 2.24mm diameter of wire, barbs at 75mm spacing. The barbs are (point wire) 02mm thick wire shall be ISI marked as per IS:278 of 1978 (Third revision) with amdt No 1 to 4. The points of barbs shall be sharp. The line and point wires shall be circular in section free from scales and point wires shall be circular in section free from scales and defects and shall be uniformity Galvalium. The barbed wire shall be manufacturedasperclause 11.2.1 and 11.2.2 respectively of IS specification cited above read with IS 4826/79 (first revision).Make:SAIL/TATA/ APLApollo/RINL/JSW complete all as specified and directed by Engineer-in-Charge |
| 4 | S&F Galvanised steel chain link fence fabric of mesh size 125mm x 125mm (+/-) 4mm of 4.00mm nominal diameter. The size of chain link fence fabric shall be 2.7 mtr x 15 mtr mesh wire. Galvalium chain link shall be manufactured as per IS 4823 complete all as specified and directed by Engineer-in-Charge. Make : TATA/JSW/RINL/ Jindal/SAIL. |
| 5 | S&F MS plat of 40x3 mm, 2.70 mtr long with 6 holes of 15 mm dia, including one coat of red oxide primer and two coats of synthetic enamel paint. 3.02 Kg per flat. Make of steel: Jindal/ SAIL/ TATA/Equivalent ISI Marked complete all as specified and directed by Engineer-in-Charge. |
| 6 | S&F Mild steel bolts with hexagonal head at one end and screwed the other end fitted with one nut and two washers. The bolts shall be 12mm dia and 50mm long. Strong long lasting, resistant to corrosion and 100% recyclable complete all as specified and directed by Engineer-in-Charge. Make:JINDAL / SAIL/ TATA/ APL Apollo/ JSW/ RINL |
| 7 | S&F MS round bars 10mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer. Make: JINDAL/ SAIL/ TATA/ APL Appolo/ JSW/ RINL complete all as specified and directed by Engineer-in-Charge. |
| 8 | S&F MS round bars 16mm dia with hook on both sides made to shape including two coats of synthetic enamel paint over a coat of red oxide primer Make: JINDAL/SAIL/TATA/APL Apollo/JSW/RINL complete all as specified and directed by Engineer-in-Charge. |
| 9 | Material and labour for excavating in Soft and dense soil trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in depth and gettingoutinsoft/loosesoil complete all as specified and directed by Engineer-in-Charge |
| 10 | Material and labour for PCC Type D2 (1:3:6) using 40 mm graded stone aggregate as in foundation, mass concreting etc complete all as specified and directed by Engineer-in-Charge |
| 11 | Material and labour for PCC Type B1 (1:2:4) using 20 mm graded stone aggregate as in foundation, mass concreting base (on ground level) chain-link fencing floor etc complete all as specified and directed by Engineer-in-Charge |
| 12 | M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 in soft/loose soil complete all as specified and directed by Engineer-in-Charge. |
| 13 | M&L removing excavated soil material exc 250 m but n exc 500 m and depositing where complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L GI binding wire 1.2mm as per IS specifications dia complete all as specified and directed by Engineer-in-Charge |
| 15 | M&L Cement Base Paint complete all as specified and directed by Engineer-in-Charge (Make: Snowcem/Jhonson/ Asian) |
| 16 | M&L Steel form work for Fdn pedestal flat Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter Make : Jindal/ SAIL/ TATA/Equivalent ISI complete all as specified and directed by Engineer-in-Charge. |
| 17 | M&L Lime (Chuna) complete all as specified and directed by Engineer-in-Charge |
| 18 | S&F Concertina Coil. Punched Tape Concertina Coil - 1A shall confirm to CQA(EE), Pune specification No. CQAE/5660/1602/a (including spike and handle) with dimensions as follows:- Dia of coil when closed :1050mm (+50mm- 0.00mm), dia of coil when opened 915mm (+50mm -0.00mm), wt of one coil : 15.2 Kg (+5% & -5 %) without packing material and coil wound with bituminized hessian cloth for providing protective coating as per standard specification. Punched tape concertina coil shall have a core wire of high carbon spring steel of high tensile strength not less than 1620 N/Sq mm. The punched tape and core wire are to be electro galvanised to provide protection against outdoor exposure with minimum zinc coating of 230 gm /sq m. The punched tape should be mechanically crimped over the core wire forming into a coil. Provn of steel clips to connect the individual turns of the coil to each other for to opens like an accordion. The width of strip shall be 19mm and spacing of clips shall be 23.5mm to 24.5mm C/C. Each coil to be slandered up to 12.50 mtr. All as specified and directed by Engineer-in-Charge. Make : SAIL/TATA/APL Apollo/RINL/JSW. |
| 19 | S&F Steel Main Gate. Steel gate 5.5 Mtr wide with Gate pillar made of RCC of size 500x400mm complete all as directed (alongwith reinforcement, RCC Column, Painting and Black Granite Cladding on gate pillars) as shown in drawing complete all as specified and directed by Engineer-in-Charge. Make : SAIL/TATA/APL Apollo/RINL/JSW |
| 20 | S&F Wicket Gate. Steel gate 1.2mtr wide with Gate Pillar made of RCC of Size 300x200mm complete all as directed (alongwith reinforcement, RCC Column, Painting and Black Granite Cladding on gate pillars) as shown in drawing. Make : SAIL/TATA/APL Apollo/RINL/JSW |
| 21 | Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment. |
