Tender For Total Turnkey Interior Fit Out Works In The Eighth Floor (B- Block) Iitmrp, Chennai-Tamil Nadu

TDR : 52963869

Tender Notice
BOQ

19 Days Left

Chennai , Tamil Nadu

Tender Brief : Tender For Total Turnkey Interior Fit Out Works In The Eighth Floor (B- Block) Iitmrp

Document Fees
Refer document

EMD
₹ 1250000.0 /-

Tender Value
Refer document

Submission Date
06-01-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Interior
2	Partitions
3	Drywall solid partition system
4	97.0mm thick Gypwall Habito partition consist ofMetal framework having maximum reachable height of 3600mm satisfying L/240 criterion at 200Pa, possessing fire rating of 60mins, tested in accordance to BS-476 Part 20 & 22 & sound insulation (Rw) of 43dB, tested in accordance to ISO 10140-2/ASTM E90 & spectrum adaption term as per ISO 717-1, having U-value of 0.425W/m²K & Heavy duty rating as per BS 5234 part. Partition comprises of single layer, tapered edge Gypsum Board, certified GreenPro by CII & strategic location of manufacturing plants results in lower carbon emissions. Partition includes single layer of 12.5mm thick®Habito conforming to IS 2095 Part 1:2011 / EN 520: 2004 - Type A,D,R,I,HB having flexural strength – {Longitudinal > 1010N & transverse > 550N} on both side of framing.™ Metal frame work, in compliance with BS EN 14195 & manufactured using CR1 Grade Steel as per IS 513, having yield stress of 300MPa & tensile strength of 340MPa with surface finish of AZ150 as per IS 15961/AS 1397 & tested for 500hrs of salt spray test as per ASTM B117, includes 70x34x36x0.5mm™ C-Stud with lip of 6.5mm and H-cutout on web enabling the services to pass, having moment of inertia 61909mm4 about major axis, positioned at 610mm c/c in 72x32x32x0.5mm™ Floor Channel & 72x32x32x0.5mm™ Ceiling Channel with flanges bend at 5° acute angle. Floor & Ceiling Channel is anchored with® Rawl plug Ø8x45mm having Pull Out strength of 6.8KN or Nail**, fixed at 600mm c/c in zig zag manner. 70x40x40x0.5mm™ Noggin Channel to be fitted at the horizontal joints of board. ®Habito board strip is placed between ceiling channel and soffit when fire rating is more than 30mins® Boards to be Screw fixed with®Habito Screw of 25mm with 30nos per m2 at 300mm at centre and 150mm at periphery. 50mm Glass wool of density 20kg/m3 shall be placed in Metal framework with the help of holding Clip. Edges & joints to be finished with® Pro-Fill JC conforming to ASTM C475 &®Paper tape. Periphery & cut-outs of the partition to be treated with suitable Fire & Acoustic Sealant. All the performance test are carried out at NABL accredited/ government approved lab.
5	Rate to include provisions to be made for fixing writing boards and soft board fabrics on to it. Rate to include on coat of altek patty and two coats of acrylic emulsion paint finish all complete. Rate to also include 50mm high aluminium skirting from JEB or Bottomline.
6	Rate to include cutouts with necessary support frames for services such as HVAC ducting, return air, and fresh air. No additional cost to be claimed for the same
7	Wall lining with Habito beside block wall for better thermal insulation and acoustic performance
8	62.5mm(Min.) thick Wall lining with C-stud partition which includes single layer of tapered edge 12.5mm thick®Habito conforming to IS 2095 Part 1:2011 / EN 520:2004 - Type A,D,R,I,HB having flexural strength – {Longitudinal > 1010N & transverse > 550N} of size 1219x2438mm mmscrew fixed to C-stud which is placed adjacent to brick/RCC wall. 48x0.5mm™ C-stud {Material-IS 513,Y/S-300Mpa, Finish - AZ150 (IS 15961)} placed at 610mm c/c in 50x0.5mm™ {Material-IS 513,Y/S-300Mpa, Finish - AZ150 (IS 15961} floor and ceiling channel. Floor & Ceiling channel is anchored to the floor & True ceiling using® Rawl plug Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} /Hilti Nail anchor fasteners at 600mm c/c in centreline manner. A™ Noggin channel {Material-IS 513,Y/S-300Mpa, Finish - AZ150 (IS 15961)} of 48x0.5mm width has to be provided at the horizontal joints of outer boards. Single layer of® boards to be screw fixed with® drywall screws of 25mm at minimum spacing of 300mm at centre and 150mm at periphery. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with® Pro-Fill Jointing compound Air Dry (Conforms to ASTM C475),® Joint Paper tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Acoustic sealant. All other detailing and specifications to be followed as per approved drawing of.
9	Vertical drop partitions till lintel level - From 2.7m to 3.8m level, bottom of true roof slab.
10	Supply and fixing vertical drop partitions from slab bottom at 3.8m level till lintel of item no\"s 5 & 6The vertical drop to be made up of 50 x 25 mm aluminium section framework at every 600mm c/c and to be strengthened appropriately with anchorfastners to the slab soffit and the civil walls at the ends. Note that the vertical drops are to be sturdy enough to hold the TG glass partition with aluminium framework. The vertical drop frame to be panelled with 2x12.5mm gypsum board on both sides of the framework. All joints and gaps to be sealed with silicon sealant to make the partition air tight.
11	Rate to include one coat of altek patty and two coats of acrylic emulsion paint finish all complete.
12	Rate to include cutouts with necessary support frames for services such as HVAC ducting, return air, and fresh air. No additional cost to be claimed for the same
13	SINGLE GLAZED SYSTEM - 10 mm TOUGHENED GLASS PARTITION - 1200 - 2700 mm high
14	Supply and Installation of Clipper Sleek Series aluminium profile for single glazed straight partition with top, bottom and side profiles of size 21mmx30mm black anodizedfinish with suitable gaskets for insertion for 10 mm thickToughened glass. It consists of 2way polycarbonate profile, 90 deg L junction, T junction and suitable fasteners for fixing profiles. Partition Height 1500mm
15	SINGLE GLAZED SYSTEM - 10 mm TOUGHENED GLASS PARTITION - 0 - 2700 mm high
16	Supply and Installation of Clipper Sleek Series aluminium profile for single glazed straight partition with top, bottom and side profiles of size 21mmx30mm black anodizedfinish with suitable gaskets for insertion for 10 mm thickToughened glass. It consists of 2way polycarbonate profile, 90 deg L junction, T junction and suitable fasteners for fixing profiles. Partition Height 2700mm
17	DOUBLE GLAZED SYSTEM
18	Supply and installation of Clipper Influence Series aluminium profile for double-glazed straight glass partition with top, bottom and side profiles of 82mmx38mm black anodised finish with suitable gaskets for insertion of 10mm thick clear toughened glass+Airgap + 12mm thick clear toughened glass. It consist of 2way polycarbonate profile and suitable fasteners for fixing profiles Price including supply and installation. Glass partition Height considered as 2700mm - The supplied toughened glass to have Low E glass from ST Gobain make or equivalent.
19	Moveable & Collapsible acoustic partition system.
20	ACOUSTIC OPERABLE PARTITION – VARIFLEX SOLID 100 (SEMI AUTOMATIC) or equivalentGeneral Description and Acoustical PerformanceOperable Partition consisting of series of individual flat elements of 100 mm thick travelling along the ceiling track assembled to form a solid wall. The entire system must function as a solid wall and even when closed should reveal minimal screws, fixing or other similar solid metal parts. The sound insulation of the operable partition should be 50/52/55 db* tested under third party reputed laboratory in accordance to EN 20140-3. The test certificate should show the make and model of the system.ConstructionElements must be constructed of a torsion-free steel horizontal tube frame and torsion-stiff vertical aluminium profiles, bolted together to make the element strong and sturdy. The frame must be clad either side with 16mm MDF panels hung in acoustic free suspension from the panel frame. The panel skin shall be installed on site and able to be replaced without totally disassembling the panel frame. The element must be constructed in accordance with the specified sound insulation requirements. The elements must be inter-connected by means of a positive locking concave/convex aluminium profile with an integrated magnetic strip and sealing lip having a linear attraction of 40N/m. The spindle mechanism in every element should be connected to the top and bottom horizontal seals which should be constructed of aluminium plates with flexible rubber at the contact point. Specially formed polyurethanecorner rubber seal to be provided for overlapping acoustic seals horizontal sealing strip. Operation (Semi Automatic)Each element must have a spindle mechanism which should be connected to the spring loaded top and bottom retractable seal. The spindle mechanism should be operated driven by a 24V DC electric motor. The power supply should be conducted from element to element via end-face plug contacts and a system connection to the mains supply via a plug-in power supply unit and a central master switch to be provided. In order to ensure functional efficiency even in the event of a malfunction or fault (power failure) an emergency unlocking device shall be provided for all the elements. The horizontal top and bottom seals must be retracted as per the operating mechanism and should ensure a contact pressure of 800N when the seals are completely extended. The spring loaded retractable horizontal seals should also be able to adjust to minor floor undulation for better acoustic efficiency. The seal spindle mechanism must be accessible while the panel is hanging for servicing and adjustment if necessary. Total disassembly of the panel frame to access internal components is not acceptable. No fixed sweep seals allowed in top and bottom of the element that would rub against the track or floor while moving the element. Telescopic / End Closure ElementThe telescopic element or the end closure element must open and close 120mm horizontally through an additional telescopic panel made of 16mm MDF provided and fixed to the telescopic element. The movement of the telescopic panel and the operation of the horizontal top and bottom seal and must be operated by a single mechanism. The telescopic element must maintain all the same quality criteria as the other elements.Pass Door (Optional)If pass door elements are required thethickness of the element needs to be 100 mm with a portal frame consisting of rigid steel profiles and two side post\"s with pressure tubes. Additional interlocking and centring of doors stiles via automatically operated floor pins to be provided. Door leaf to be flush with face of Partition. Door leaf should consist of steel frame and automatically operated retractable floor seal. Sealing mechanism (top seal and floor plugs) to be operated at the edge of the element with integrated door leaf mechanism (no additional manual operation).Element Suspension (for single element weight < 500 kgs)**An aluminium track profile shall be installed to ensure easy, low-noise operation of the elements. Additional track cladding must not be necessary. It shall be possible to implement all right-angled and positive-guidance stacking track assemblies with this track design.Each element must be suspended on the aluminium track by \"maintenance free\" multi-directional trolley capable of withstanding a minimum load of 500kgs per element. Additional ledge should be provided on the track for the movement of the trolleyproviding the extra strength to the track and smooth movement of the element. The trolley shall consist of a four sided die cast aluminium body. Multidirectional ball bearing wheels shall be steel-rimmed mounted to each of the four side and shall be capable of navigating track intersection. The trolley shall incorporate four nylon horizontal navigating wheels, mounted to the top of the trolley body, to provide guidance for smooth operation. To allow for minor structural sag in the ceiling, the elements must be designed for easy height adjustment without the need to open up either the ceiling or the element.
21	Doors
22	Clipper Influence Series System for single Glazed Stile Glass door.
23	Supply and Installation of Clipper Sleek series Door frame size 55X32mm and Single leaf single glazed stile door frame size 40 x 82 mm with black finish withHardware -make Flush Hinges (5 Nos) & 300mm offsetHandle with NSL dead Lock 35mm backset, oval escutcheons , strike plate, EPC cylinder both side key-70mm and SGF840 Exposed Door closer with Hold Open unit with 11.52mmlaminated glassand necessary seals to be provided all around the door frames and drop down seal .-Single leaf Glass Door 1000x2400mm
24	Clipper Influence Series System for double Glazed Stile Glass door.
25	Supply and installation of Clipper Influence series Door frame size 82X38mm and Single leaf Double glazed stile door frame size 40 x 82 mm with black finish withHardware -make Flush Hinges (6Nos) & 300mm offsetHandle (02nos) with NSL dead Lock 35mm backset, oval escutcheons , strike plate, EPC One Side Key other side knob-70mm and concealedDoor closer with Hold Open unit with 6mmtoughened glass+ airgap+8mm toughened glass and necessary seals to be provided all around the door frames and drop down seal .-Single leaf Glass Door 1200x2400mm
26	Steel doors - Providing and fixing clean room steel doors with 1 hour fire rated door, drop leaf hinges and seal. Size 1000mm x 2400mm (Shakthimet or equivalent). Rate to include vision panel, Door closer of approved make or equiv, handles, locks etc. all complete.
27	Solid flush doors - finished with laminate as per drg. Rate to include all hardware etc. all complete with Door closer(approved make or equv)- 1000x2400mm with a 200 mm x300 mm vision panel and louvers of size 150 x 300mm in the lower panel of the door. Door frame with 75X40mm teak wood to be considered with enamel paint finish.
28	Solid flush doors - finished with laminate as per drg. Rate to include all hardware etc. all complete with Door closer(approved make or equv)- 1000x2400mm. Door frame with 75X40mm solid teak wood to be considered with natural melamine polish finish and rebate as per standards.
29	Miscellaneous
30	Panelling on wall / column - Laminated finish - Providing and fixingwith 12mm plywood fixed directly on wall or column finished with 1m laminate as per design till 1200mm leveland soft board above it till 2400mm level which will be paid separately / drawing all complete.
31	Same as above but panelling to be done with 6mm lacquered glass - make (basic rate to be 400/sft) - With 6 mm commercial ply backing and to be flushed with the rest of the panelling surface level.
32	Panellingoncolumns - Laminated finish- Providing and fixingwith 12mm MDF over framework of Aluminium sections of 25x50 mm directly on columns finished with 1m laminate as per design / drawing all complete. Gap of boxing to be 50 mm.
33	Same as above but panelling to be done with 6mm lacquered glass - make (basic rate to be 400/sft)
34	Acoustic panelling - Providing and fixing acoustic boards with 12mm thick Synthetic wool petpanels (Basic rate not less than Rs 100/sft).The panel to be fixed on to the wall or partition with Aluminium L trim for a solid wall and dry wall surface application.
35	EOS 500 ROLLERSHADESSPECIFICATIONS FOR approved make or equivalentProviding and fixing Roller Blinds manufactured by Hunter Douglas, to the following specifications:TheDRIVEUNITshallbeofpatentedclutchforquick,easyandsafeinstallation, molded plastic with steel spring support and inserted into the tube end. It shall be driven by a ball chain pulley with ball chain and can be positioned at right side or left hand side of the Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a built in friction lock. Universal clutch for left and right hand operation. Chain Gear Ratio of 1.75:1The END PLUG shall be molded of plastic with a steel location pin. The plug shall be inserted into the tube end. (Opposite to the Drive Unit) for ease of installation.The SUPPORTBRACKETS(Bracket55)shall be of coated steel & provided with covers and used in right hand or left hand positions differentiated by the acceptance oftheoftherectangulardriveunitsupportortheroundidlerplugpin.Canbe installed a) On Face b) Ceiling Mount c) On Frame d) in RecessThe Bracket should be protruding outside maximum of 80mmTheROLLERTUBEshallbeofextrudedaluminiumwith50mmdiameter&skin thicknessof 1mmandshallincorporateakeywayintegralwiththetube to accommodate the spline.The BOTTOM RAIL shall be a Flat Bottom rail of Aluminium Extruded as a stiffening element inserted into a bottom rod pocket. The material may be timber, PVC covered steel tube or VB Bottom rail
36	Blackout Fabric Specification:Basic Material: 100% PolyesterFabric Width: 200 / 250 cmFabric Weight: 270 - 295 g/m2Thickness: 0.50 mmFinishing: Blackout Fabric, reverse & front side pigment colour coatedColour Fastness: > 5-6Rubbing Fastness Depending on colourShrinkage (%)- Warp: < 0.5 % Weft: < 0.5 %
37	Screen Fabric Specification:Fabric Specification 3%Openness:Mario Fabric made up of 24% Polyester and 76% PVC coated110tex Tilter Basket weave of thickness 0.61mm(ISO 2286-3) and weighing 485gsm±5%(ISO 2286-2)with openness factor of 3% .UV Screen Up to 97% ,The tear resistance (Warp: >_120N &Weft: >120N) As perISO 4674, and Fire, Smoke classification FR (US) - NFPA 701 TM#1 &BS (GB) - 5867 Part2 Type B & B1(CN)-GB50222. Break Resistance (Warp: >1600N/5cm & Weft: >1800N/5cm as per (ISO 13934-1) Bacterial & Fungal Resistance ASTM G21-09, ASTM E 2180-07 Reduce more than 99.9% of bacteria. Greenguard GOLD, EN71 Part 3:1994. Colour fastness Grade 6 ISO105 B02:2014 >_4.0 AATCC TM 16.3-2014; Option 3; Xenon Arc Lamp, Health/Safety-Oekotex Standard 100 Class IV certification
38	Motor Specification:ThesearequietACmotorsthatareidealforrollershades.Theavailablestandard mechanicallimitversionofferssimpleadjustmentoftheupperandlowerlimit positionswithpreciselimitswitches.MotorscanbeoperatedfromstandardAC switches.Nominal Torque (Nm): 4 Output Speed: 26 rpmFinal limit Position range: 40 revolutions Mains Voltage: 230V / 50HzPower Consumption: 90 WNominal Current Consumption (A): 0.39 Operating Mode: 4 MinDegree of Protection: IP 44
39	White boards -Magnetic type with 3M coated film on surface- Rate to include providing Aluminium trim all around.
40	Pelmets - Providing and fixing of laminated pelmets with 18mm ply 200 mm deep and 200 mm wide with laminate finish from both internal & external surfaces. Edges to be finished with PVC edge banding of approved make or equivalent
41	Boxing - Providing and fixing boxing in locations as per drg. With 12mm mdf over necessary framework of Aluminium sections of 50x25mm with 1mmlaminate finish. Rate to include providing grooves, shapes all as per drg., hardware all complete. Surface area of panelling around the boxing will be measured for payment.
42	Dirt matting -From approved make or equivalent as per approved sample.
43	Skirting
44	Providing and fixing proprietary Anodized Aluminium Skirting of 50mm high, as per details and Architect\"s approval.Bottomline or equivalent.
45	Trap doors
46	Providing and fixing factory fabricated Trap doors in the false ceiling as per service requirements as follows. Trap Door Frames are made of Aluminium Alloy 6063 with the Thickness of 1.5mm and 30mm width.• Core Panel made out of Synthetic Board (12.5mm thickness).• Corners of the frame are reinforced with non-corrosive galvanized steel angles with Shutter removable hinges.• Safety latch secured by galvanized angle on the inner side of frame Various dimensions available.• Shutter to be pressed open with click lock.• Self-activating pressured spring locks. Certified to be used for 500 times (open and close).• Shutter extra supported with guard hook and SS rope for safety purpose.
47	Material:Frames made from stable Aluminium profile.Closing / Opening Mechanism:2 x Spring loaded galvanized steel locks with safety roped hook.Connecting Frame Parts:Galvanized steelMaterial Inlay:USG Boral (MR) Moisture resistant gypsum board / Synthetic Board /Aluminium Panel.Material Screws:Phosphate, rust-prevented, spike protected with cap.Standard Sizes:• 200 x 200 mm• 300 x 300 mm• 400 x 400 mm• 450 x 450 mm• 500 x 500 mm• 600 x 600 mm• 900 x 900 mm• 600 x 900 mm• 600 x 1200 mm• 1200 x 1800 mm• Any Custom size’s also made as per client requirement\"s.
48	Architrave
49	P&F Beech wood architrave 40mm x 18mm as per design and detail around existing doors, shutters. Rate to include fixing the same on walls, mitre joining at the corners and melamine polish as per desired shade.
50	To close wall openings with mdf board of 12mm thickness and to accommodate services like ducts of specific sizes and sealed and finished with mdf beading all around the opening made in the board. To include finish with PE paint as well.
51	3MM - Epoxy Self Levelling Flooring System
52	Note: All the new flooring substrate shall be allowed to cure and dry completely according to standard practice. The substrate shall be of minimum M20 grade with VDF / IPS finish. The base should be hard & strong (minimum tensile strength of 1.5 N/Sqmm). The base should be free from random cracking & potholes. Flatness of the base should be checked for level to ensure that the specified thickness of treatment can be applied over the whole area. All the expansion & movement joints should be properly cut and maintained for terminations. The preferred method of surface preparation is by mechanical means. The substrate shall have moisture content of less than 5%. This product shall not be applied on the floors that are known to have rising moisture or have relative humidity of greater that 75% at the time application. All application shall be not carried out where temperature less than 10 Deg C or above 40 Deg C
53	Surface preparation:- Cleaning the entire floor surface to make it free from dirt, dust, loose particles, wax, polish, efflorescence, laitance, curing compound and other contaminants by using suitable equipment\"s like wire brush, grinding all sharp edges to make it flush with the surface, etc and undulations should be levelled with epoxy mortar etc and complete as per manufacturer\"s specification.
54	Priming:- Providing and applyingAsian or equivalent Apcoflor HFP 120/ Apcoflor HFP 130, solvent free epoxy primer coat of coverage 200 gms / sqm, using a brush or short / medium spike roller at a time gap of 8 hrs by ensuring a uniform coating is achieved and compensated the differences in surface porosity, allowing second coat to dry for 24 Hrs, etc and complete as per manufacturer\"s specification.
55	Epoxy Self Levelling screed:-Providing and laying,Asian or equivalent Apcoflor LSC3high performance, self levelling epoxy resin flooring system by mixing all 3 components using heavy duty slow speed drilling machine fixed with mixing paddle, pouring of mixed material on the primed surface and spreading it using suitable trowel / pin rake trowel at 2mm thickness, gently rolling the spike roller to remove the entrapped air, etc and complete as per manufacturer\"s specification.
56	Epoxy self levelling Topping : Providing and laying, Asian or equivalent Apcoflor SL1 TC, high performance, epoxy resin self levelling flooring system at 1mm thick by mixing all components including Pigment, using heavy duty slow speed drilling machine fixed with mixing paddle, pouring of mixed material on the primed surface and spreading it using suitable trowel at 1mm thickness, gently rolling the surface of Apcoflor SL1 TC using spike roller to remove the entrapped air, etc and complete as per manufacturer\"s specification.
57	Providing and fixing of Aluminium L profile of size 12mmx12mm on top open edge oflaminated wall panelling.
58	Providing and fixing ofss Transition profiles in the flooring for covering the jointsbetween two different flooring materials and even for serving as a transition profile between two different floor levels. The ss profile is to be 32mm in width and to have a brushed finish. SS Grade to be 316L and 1.2 mm thick. Profile to be flushed with floor level.
59	Carpet flooring - 20 oz and above
60	Supply and application of Nylon carpet tile flooring as per the specifications as mentioned below. Note that the rates to include pattern making and customisation as per flooring concepts and design enclosed for reference.
61	Size - 500 x 500 mm
62	Construction - Multilevel pattern loop pile
63	Yarn - 100% BCF Nylon 6.0
64	Dye method - 100% solution dyed
65	Gauge - 1/12
66	Production weight - 22 oz psy
67	Total thickness - 7.0 mm
68	Secondary Backing - Condensed Vinyl with Fibreglass Reinforcement
69	Packing - 20 pcs per box.
70	Rate to include covering of finished flooring with poly urethane sheet as a protective layer till the space is handed over.
71	Main Company logo
72	Company logo to be cut and shaped as per details enclosed, Signage to be done in acrylic backlit with LED lighting.
73	Glass ledges - 650 x 450 mm deep.
74	Supply and fixing of 12 mm thick toughened glass ledges to be fixed with ss finished D brackets and all compete.
75	Architectural films - Providing and fixing of 3M dusted crystal film on glass as per design and pattern. Rate to include shape cutting
76	Supply & fixing of 300 mm wide 12 mm thick with pvc edge banding - pre laminated sill panelling along the running length of the external glazing.
77	Mirrors -as per drg. Rate to include backing ply, fixing with 3m double side tape, laminated or polished wooden frames as reqd Basic rate for mirrors 250 per sft
78	3mm safety walk film on ramp for providing more grip and anti skid surface on inclined spaces.
79	Providing and fixing of spot lightsupporting ply board of 6mm thick for supporting spot lights and recessed down lighters in the grid ceiling system.
80	Providing & fixing Planter box with laminate finish in various locations below double ply with round cutting near storage - 300 X 300 X 600 MM in length- To be made with 12 mm ply and laminate finish.
81	Supply and installation of Raised access flooring as per standards, height to be 200 mm with all frameworks and accessories all complete. Unitile, Flexifloor or equivalent.
82	Bare Raised Flooring
83	Providing and fixing raised floor system as per below mentioned specification
84	Vinyl top finish panels
85	Nominal size of floor panel : 600 mm x 600 mm
86	Permissible thickness : 35 mm
87	Concentrated Loads : 450 Kgs ( 1000 lbf ) with a top-surface deflection under load and a permanent set not to exceed , respectively,2.54 & 0.25 mm ( 0.10 & 0.010 inch ) according to CISCA A/F, Section I ‘’ Concentrated Loads’’
88	Ultimate Concentrated Load: 1125 kgs (2500 lbf ) without failing according to CISCA A/F, Section II ‘’ Ultimate Loading’’
89	Rolling Loads : 225 kgs ( 500 lbf )of the following magnitude, with a combination of local and overall deformation not to exceed1.02 mm (0.040 inch) according to CISCA A/F, Section III ‘’ Rolling Loads’’ CISCA AF Rolling Load: 10000 Passes
90	Pedestal Axial Load Test : 22 kN axial Load per pedestal, according to CISCA A/F, Section V, ‘’Pedestal Axial Load Test ’’
91	Pedestal Over Turning Moment Test : 113 N x meters, according to CISCA A/F, Section VI, ‘’Pedestal Overturning Moment Test’’
92	Uniformly Distributed Load (UDL) : 1350 kg/m2 with a maximum permissible deflection of not more than 1.52 mm as per definition of “Uniform load” of CISCA tested over an area of 300x300 mm square for 126 kgs load
93	Fire Rating : The Panels shall confirm to Class O & Class 1 Fire Ratings tested as per BS 476 Part 6 (Fire Propagation) & 7 (Surface spread of flame) as also ASTM E84 1998 (Flammability) and ASTM E136 (Combustibility)
94	Panels : Access Floor panel of size 600x600 mm shall be all steel welded construction, with an enclosed bottom panandtop plain sheet which are fuse welded atvariouslocationstoformapanelofanoverallthicknessof35mm.Thepanelaftercleaning,degreasing,to the panel surface and corrosion resistance. The inner empty core of the panel shall be injected with a light weight fire retardant, non combustible cementitious compound at high pressure to fill in all the crevices of the panel and ensures support of not less than 90% of the top surface area of the panel.The panel shall have located corner holes on all edges for bolting the panel to the substructure to form a rigid monolithic smooth levelled floor.
95	SUB STRUCTURE -PEDESTAL ASSEMBLY :Sub structure installed to support the panel shall be suitable to achieve a minimum finished floor height of 150 mm to a maximum of 600 mm from the existing floor level. Pedestal design shall confirm speedy assembly and removal for relocation and maintenance. The assembly shall provide easy adjustment of levelling and accurately align panels for a maximum ± 25 mm in the vertical direction. Pedestals shall support an axial load without permanent deflection and an ultimate load as laid out in System Performance requirement.The Pedestal head assembly shall consist of a 75 x 75 x 3.50 mm embossed head mechanically riveted to a100mm long ¾” Dia rolled formed stud and 2 check nuts for level adjustment and arresting vertical movement.ThePedestalBaseassemblyshallconsistof22.20mmODpipemechanicallylockedonapressforperpendicularity and then welded to a base plate of 100 x 100 x 2 mm thick with stiffening folds.The sub structure assembly shall be suitably anchored to the floor with suitable adhesiveas recommended by the consultant / manufacturer. All steel components shall be zinc electro plated.
96	There shall be grommets given to corner of tiles to suit the grid design for power / data / voice outlets.
97	The raised Access Flooring shall be as per PSA MOB PF2/S/SPUstandards.
98	200 mm High
99	Supplying two-cup vacuum suction lifting handles suited to the Raised floor system.
100	Provide and install 75 mm dia. Heavy Guage PVC grommets with rotating cover and passage for cables in pre-cut openings. The edges of the openings to be properly polished to prevent any injuries
101	Approved make or equivalent
102	Supply and application of Vinyl rool flooring.
103	Size - 2.6mm thick x 2000 mm x 15 m long
104	Production weight - 4000 gms/sqm
105	Total thickness - 2.6mm
106	Product code - 0503
107	Shade name - Honey - Fonteny
108	Basic rate - 125 per sft
109	Rate to include installation with welding rods
110	European classification - 34-43
111	Fire rating(EN) - Bfl-s1
112	Static electrical propensity <2
113	Slip resistance wet - R9
114	Abrasion resistance - ≤2
115	Thermal conductivity - 0.25
116	Special maintenance treatment - ProtecsolTM
117	Anti-bacterial activity(E.coli - S.aureus - MRSA) - > 99% inhibits growth
118	Supply and erection of acrylic marker/duster holders - 75x75x200 mm
119	Rate to include covering of finished flooring with poly urethane sheet as a protective layer till the space is handed over.
120	Supply and installation of Raised access flooring as per standards, height to be 300 mm with all frameworks and accessories all complete. Unitile, Flexifloor or equivalent.
121	Soffit panelling on wall vertical surface
122	Supply of Vicstrip (single slat/double slat) having size of 2400x600x13mm(+/- 0.5mm) thickness, backing of 12 mm PET panel with front facia of 1 mm laminate. The product use for absorption of medium and high frequency range with NRC of 0.50 direct fix. Panel Should be anti fungal as per ASTM G:21and also Non-toxic, non-irritant, and fire compliance with safety standards confirm as per BS 476 Part 6 passes (Fire Propagation) & Part 7class2 (Surface spread of flame) ,for interior applications-The product must come with EPD certificate and Declare Label.The product should be 100% make in India and OEM must have ISO CERTIFICATIONS- complying to- IGBC membershipISO 14184-2 (no formaldehyde)ISO 9001 (Quality Management System)ISO 14001 (Environmental Management System)ISO 45001 (Occupational health & safety management system) Approved Make or equivalent
123	Restroom HPL Cubicle
124	Model Type: Shower Cubicles
125	Size of Cubicles : As Per Drawing
126	Colour of HPL Boards: As Per Vendor shade card
127	Thickness of Compact Laminate : 12mm
128	Door: 600mm*1785mm
129	Shower Cubicles (Thickness 12mm, Door 600x1785, Divider Height 1820, Overall Height 1995 )
130	SCOPE OF WORK Supply and installation of (Nylon) series cubicles of width and depth as per specifications/site drawings.
131	ITEM DESCRIPTION Made from High Pressure Laminate (HPL) compact panel manufactured as per IS:2046 and EN-438 by applying high pressure on a bunch of kraft papers impregnated with thermosetting phenolic resin and decorative papers, impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti and moisture resistance along with anti-bacterial properties.
132	DOORS All doors will be of single colour and made of 12 mm thick HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3. Nylon PA - 6 made hinges affixed to the pilasters. Nylon PA - 6 made coat hook and lock set are provided with each door
133	PILASTERS All pilasters will be made of 12 mm thick HPL compact panel with chamfered edge and completed with SS made thumb-turn lock set. Aluminium made door stopper profiles with rubber linings for dampening the noise while door closing will be provided at the vertical ends of the pilasters. Pilasters will be anchored to the floor using Nylon PA - 6 made adjustable legs. The bottom gap is 150-200 mm.
134	DIVIDERS All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. They are affixed with aluminium made U-channel at their ends for ultimate stability of the system. Design No. as specified by Arch./Engr. in suede finish. Size of panels to be as per drawing.
135	HARDWARE AND ACCESSORIES • Semi-spherical (Top) head frame structure for surface protection, size to be 50 x 32 x 1.6T. Corner joinery section, size to be 40 x 16.5 x 1.8T. U-Channel Wall joinery section, size to be 22 x 16 x 1.6T. Door stopper section, size to be 21 x 12.5 x 1.6T • Nylon Polyamide grade 6 adjustable pedestal footing of base minimum diameter 70 mm, giving a clearance height of min 150 mm to max 200 mm • Self closing hinges (gravity mechanism) made from nylon polyamide grade 6. Colour to be as per specifications • Round Coat hook with base diameter 53 mm made from nylon polyamide grade 6. Colour to be as per specifications • Round Door knob diameter 48 mm with thumb-recess made from Nylon polyamide grade 6. Colour to be as per specifications • Rotating thumb-turn locking system with privacy indicator locking system made from Nylon polyamide grade 6. Colour to be as per specifications • Anti-noise rubber padding • SS grade 304 screws • Anti-rotation nylon polyamide grade 6 expandable wall plugs • The work shall complete as per drawing , under supervision of engineer in-charge and company experts
136	Accessories Details : Aluminium, Nylon
137	a) Nylon Adjustable foot
138	b) Aluminium U Channel
139	c) Nylon Gravity hinges
140	d) Nylon Coat Hook
141	e) Nylon Door Knob
142	f) Nylon Thumb Turm Indicator
143	g) Aluminium Door Stopper Channel
144	h) Aluminium Top Rail
145	I)Screws, Wall Plugs & Noise Tape
146	j)Nylon Towel rail
147	Installation Charges per cubicle
148	Wall finishes
149	Providing and applying 2 (two) or more coats of paint of approved manufacturer and shade to walls, ceilings, and other similar areas at all levels, applied evenly to produce uniform even surface to approved finish including cleaning and preparing the surface, puttying with Birla putty or equivalent all as per manufacturer\"s specifications, applying a coat of approved primer, including scaffolding, wetting and curingsurface in case of applying cement paint etc., complete.(Please note that in the case of ceiling paints, painting of exposed beams shall be considered for payment, but if there is a wall underneath the beam, the paint on the beam will be payable at the wall painting rate only)
150	Application ofapproved make or equivalent Putty to wall surfaces. Putty not to be applied on those surfaces which are getting panelled. All wall surfaces to be marked for putty work and approval taken
151	Plastic emulsion painting - Supply and application ofwashable interior grade Asian or equivalent plastic emulsion paint on walls with 1coat of wall primer and 2 or more coats of plastic emulsion paint as per manufacturers\" specifications etc. all complete. All painting final coats to be done after removal of face plates of switch boards in co ordination with the electrical contractor and face plates to be fixed only after satisfactory completion of painting.
152	Same as above but for ceiling painting.
153	Enamel paint
154	P& applying satin enamel paint on walls as per manufacturer\"s specifications ( Asian paints or equivalent)
155	POP punning
156	Supply and application of POP punning to a thickness of 10-12 mm. Application after cleaning the wall surface to get a seamless finish. Application to be done as per manufacturers\" specifications etc. all complete.
157	Special texture paint
158	Supply and application of special paint from Stuhhi or Gioio with metallic or stone finish textures, Basic rate to be considered is 245inr/ sft.
159	Storages
160	Duct shutters
161	P&F laminated shutters for janitors closet made with 19mm waterproof plywood. Rate to include providing Aluminium frame all-round and at 450mm C/C vertically to avoid bend in shutter, concealed type hinges and dead lock and recessed handles and concealed tower bolts. Typical shutter width not to exceed 450 mm.
162	DB shutters/ battery rack shutters.
163	P&F laminated shutters tp conceal Elec DB\"s at various locations made with 19mm thk waterproof plywood. Rate to include providing Aluminium frame all-round and at 450mm C/C vertically to avoid bend in shutter, concealed type hinges and dead lock and recessed handles and concealed tower bolts. Typical shutter width not to exceed 450 mm.
164	Pantry /Utility counter and storage
165	Storage in pantry - 600mm depth, 900mm high with granite top - Providing and fixing in position storage made of waterproof ply with 18mm thk. polished granite top with edge as per profile in drawing. storage box construction same as item F1. Unit to have a top row of drawers and shutter storage below. Rate to include making skirting, groves, all hardware etc. all complete. Storage to have laminated finish in the internal sides and the shutters to be made with aluminium frame and G profile for handle provision, Lacquered glass of 6mm thickness to be fixed onto the aluminium frame as per standard. Shutters to be fixed with soft close hinges. Elevation area considered for quantity measurement. Laminate and glass finish to supplied as per approved sample.
166	Janitor closet with shutters
167	P&F laminated shutters at various locations made with 19mm thk waterproof plywood. Rate to include providing Aluminium frame all-round and at 450mm C/C vertically to avoid bend in shutter, concealed type hinges and dead lock and recessed handles and concealed tower bolts. Typical shutter width not to exceed 450 mm.
168	False ceiling works
169	Soffit panelling on ceiling - Suspended from true ceiling
170	Supply and fixing of 1mm (10% +/-) Polymer Based Soffit ceilings of PARE Innovations with Perforation if deemed required, of panel sizes of 340mmx 3060mm//340mm x 4000mm along with option to custom size to a maximum of 12800mm in length in approved shade, manufactured in India, made with High temperature thermal transfer technology, waterproof, fire retardant and anti-bacterial. Termite resistant, rust proof material. Panels to be installed with Aluminium/ GI sections of suitable gauge & size, subject to change according to site conditions. Panels to be installed using suitable, same shade J-Trim with dimensions 39x20x3060/4000 (all in mm) for edge profiles and Connector with dimensions 76x20x3060/4000 mm, using same shade for connecting panels, using outside corner with dimensions 61x63x3060, which can be used in +90 degree corners and inside corner having dimensions 28x76x3060 which can be used for -90 degree corners. Panels are maintenance free and with 10 years warranty for colour & finish of the panels Including trims of PARE Innovations. All material, accessories, ancillary component all as per recommendation of PARE Innovations. or equivalent
171	Refer to tender drawings for details
172	Suspended Baffle ceiling - 300 mm deep x 2400 mm long
173	Providing and fixing floating ceiling with 25mm thick synthetic wool Baffles, the ceiling to be suspended with Gripple wire as per standards from the available true ceiling as per details mentioned. The suspension depth is to be as per the details enclosed. The acoustic board to be cut to shape as shown the presentation and views enclosed. Rate to include provisions to be made for housing service like, FAS systems, lights and HVAC etc. Note that the whole area of application will be measured for this installation. Basic rate for acoustic panel to be considered is 225 inr/sft from Techno acoustic panels or equivalent.
174	Sound Absorption:Products tested by ARAINRC value: Up to 0.9 NRC
175	Composition: 100% PET
176	Panel Dimensions: 2440 mm * 1220 mm
177	Same as above but in curved profile along the vertical plane as per design and details indicated in tender drawings and presentation
178	Same as above but in curved concentric circles shapes as per design and details indicated in tender drawings and presentation
179	Same as above but with 12 mm thickness panels and in open cell gird of 150 x 150 mm c/c spacing in conference rooms and executive cabins.
180	STRETCH CEILING WITH LED BACK LIGHT
181	Stretch ceiling
182	Stretch fabric ceiling - \"Barisol-Euroceil \" or equivalent.. Rate to include supply and installation.
183	Supply and installation of demountable PVC stretch ceiling welding with harpoon ready to install
184	Fire rated to European standards b-s1-d0/b-s2-d0/B1/B2*
185	UL Classified as per standards - UL 723
186	10 Years warranty on membrane seam raptures & profile. All joints to be fused/provided with approximate interface trims to be able to demount the ceiling to access the lights. Lighting solution with LED, necessary drivers, accessories. The ceiling shall be installed as per details drawing using proprietary aluminium profile complete as per Manufacturer’s installation guidelines and as per approved shop drawings in line with the design intent and approval by the Architect/PM.
187	PHYSICAL PROPERTIES-Thickness -0.17mm, Weight - 220 gms/sq.m
188	MECHANICAL PROPERTIES-Breaking Strength-Lengthwise : 204Kg/Sacm (DIN-EN ISO 527-3/2/200 Standard, Widthwise : 204Kg/Sacm (DIN- EN ISO 527-3/2/200 Standard)
189	Elongation Under Tensile- Lengthwise : 140% (DIN- EN ISO 527-3/2/200 Standardi, Widthwise: 150% (DIN - EN ISO 527.3/2/200 Standard)
190	LIGHT TRANSMISSION & REFLECTION PROPERTIES OF TRANSLUCENT PVC FABRIC
191	Light Transmission 41%/EN410:20111
192	Light Reflection 57 8% (EN410.201 11
193	Rate to also include LED strip light from OSRAM or equivalent with 8W per Meter output with 4700 K colour temperature and minimum 5 years warranty.
194	Basic rates for Stretch ceiling and LED strip light to be 1250 per sft.
195	Rate to also include AMC for Minimum 3 years for general upkeep of the installation including the lighting.
196	Supply and fixing ofceiling panels with Rigitone false ceiling system
197	M/F Rigitone Activ’Air 8/18 Ceiling includes 20x28x30x0.5mmTM Perimeter Channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is fixed along the perimeter of existing wall with the help of HILTI HPS - 1 (6x40) impact anchor at 600mm centres. 25x10x0.5mmTM Ceiling Angle {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is suspended by fixing it to the 27x37x25x1.6mm® soffit cleat {GI(IS513)YS-260Mpa,Finish-Galvanised 120GSM(IS277)}. Soffit Cleat and® Rawl Plug- Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} creating 1000mm x 900mm grid. 15x45x15x0.9mmTM Intermediate channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277) fixed to the ceiling angle at every 1000mm c/c} andTMCeiling Angle is fixed at every 900mm along the length of Intermediate channel with M6 x 12mm Hex Bolt & Nut arrangement {Material–As per EN 10083 Finish – Zinc Plating} or with 2 Nos of Ø4.2x13® metal to metal screw {Material-Carbon steel EN-ISO 7049/50 Finish- Zinc Coating Thickness- 4.14micron.}. 80x26x0.5mmTMCeiling Section {Material-GI (IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is then fixed to theTM Intermediate Channel {Material-GI(IS513),YS-260Mpa, Finish-Galvanised 150GSM(IS277)} with the help of® Connecting Clip {Material -High carbon spring steel wire(BS970Gr.En42),46-48HRC,Finish-Zinc plating 4-6 micron} and in direction perpendicular to the Intermediate channel at 333mm c/c. Boarding shall start from the center of ceiling area. Single layer 12.5mm Rigitone Activ’Air 8/18 board of size 1188x1998mm having all four square edges, 15.5% perforation area of board & hole size of 8mm diameter at a c/c of 18mm; backed with acoustic tissue, having NRC values 0.55, is then screw fixed to ceiling section with 30mm Rigitone screws/25mm drywall screws {Material-Carbon steel EN-ISO 7049/50,Finish-Case hardened Grey Phosphating} at 170mm centres. For higher NRC value, Resin bonded glass wool of 24kg/M3 and 50mm thick can be placed on top of the board ( Refer Rigitone Activ’Air 8/18- PDS for the NRC values). Finally all square edges of the boards are to be jointed and finished so as to have a flush look. The joint filling using Vario joint filler and Rigitone joint filler set technique should be employed for the joint-less installation of Rigitone perforated boards with continuous Perforation. After installation and joint-filling, the boards should be primed and then painted with a short haired paint roller. Paint should not be applied using a brush or spray diffuser . Serrated steel section has effective thickness of 2T (2xdepth), better load carrying capacity, enhanced screw retention, Improved acoustic performance & fire resistance as compared to plain steel section.
198	Rate to include two coats of acrylic emulsion paint with primer as per approved sample as well.
199	M/F Suspended Plain Ceiling includes™ Perimeter Channel {Material-GI(IS513),YS-260Mpa,Finish- Galvanised 150GSM(IS27 )} is fixed along the perimeter of existing wall/ partition with the help of HILTI HPS - 1 (6x40) impact anchor, at 600mm centres.™ Ceiling Angle {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is suspended by fixing it to the® soffit cleat {GI(IS513)YS-260Mpa,Finish-Galvanised 150GSM(IS277) }. Soffit Cleat and ® Rawl Plug- Ø8x45mm {Material-IS 513 CR2 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} creating 1220mm x 1220mm grid.™ Intermediate channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277) } is fixed to the™ Ceiling Angle with M6 x 12mm Hex Bolt & Hex Nut arrangement {Material–As per EN 10083 Finish – Zinc Plating} or with 2 Nos of Ø4.2x13® metal to metal screw {Material-Carbon steel EN-ISO 7049/50 Finish- Zinc Coating Thickness- 4.14micron.} The™ Ceiling Section {Material -GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is then fixed to the™ Intermediate Channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} with the help of® Connecting Clip {Material-High carbon spring steel wire(BS970Gr.En42)-46-48HRC,Finish- Zinc plating 4-6 micron} and in direction perpendicular to the Intermediate channel at 457mm c/c.5. Single layer of 12.5mm tapered edge Gypboard® Plain (conforming to IS 2095-Part 1:2011, Certified board) is then screw fixed to ceiling section with 25mm drywall screws {Material-Carbon steel EN-ISO 7049/50,Finish-Case hardened Grey Phosphating} at 230mm centres on ceiling section & 150mm at periphery of ceiling. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with® Pro-Fill Jointing compound (Conforms to ASTM C475),® Joint Paper tape. Serrated section has effective thickness of 2T ( 2xdepth), better load carrying capacity, enhanced screw retention,Improved acoustic performance & fire resistance as compared to plain steel section.
200	GUIDE SPECIFICATION FOR MODULAR GRID CEILING SYSTEM
201	GRID CEILING
202	Supply and installation of modular Grid ceiling as per specifications enclosed,
203	Silhouette Grid
204	Reveal : 6mm wide in white color
205	Tile thickness - 15mm
206	Edge detail - Straightedge
207	Humidity resistance - 95%
208	NRC - 0.5
209	Light reflectance - 90%
210	Fire performance - Class 0/Class 1 (BS 476)
211	Sound Attenuation - 30 DB
212	Ceiling Suspension System
213	Proprietary supplied ceiling suspension system to consist of 2mm or 3mm GI suspension rod/wire with adjustable butterfly clip securely affixed to structural ceiling using soffit angle fixing bracket and 10mm dia hook type anchor fastener. Ceiling suspension system to be fixed at interval (grid) of 1200mm in both directions.
214	Grid System
215	Supply of proprietary concealedGrid System to consist of Main Runners @ 600mm and joined by Cross Tees @ 600mm to form overall grid opening of 600mm x 600mm. Additional cross tees are to be placed where appropriate for light fixtures, AC diffusers.
216	The grid system used shall be hot dipped galvanised steel sections, with exposed surfaces chemically cleaned and capped prefinished in baked polyester paint
217	Lay-in Tile
218	The grid system to have shadow wall angle as per details
219	600mm x 600mm x 15mm mineral fibre grid tile - CertainTeed- Sand Micro Tiles.
220	Same as above but with 600x600 tiles with either laminated finish or moisture resistant finish both on the rear and the front of the tiles - Gyprex® Majesty Tiles.
221	VMT Clouds - Printed suspended ceiling system
222	Supply of VMT Printed Clouds (in shape of Round/ Triangle/Hexagaon/Petal)which shall be processed with VMT technology for surface customization, colour options andpattern as per the designers requirement(from our lookbook) the Clouds shall be made from--100% polyester fiber, with up to 70% recycled fiber. Centre Thickness - 40mm (+/-1mm)Panel Should be anti fungal as per ASTM G:21and also Non-toxic, non-irritant, and fire compliancewith safety standards confirm as per BS 476 Part 6 (Fire Propagation) & Part 7 (Surface spread of flame) ,ASTM E 84 Class A, EN 13501 part 1C, S2,d0 for interior applications. Noice reduction coefficient (NRC) - varies from 0.30 to 0.60The product should be 100% make in india and OEM must have ISO CERTIFICATIONS- complying to- IGBC membershipISO 14184-2 (no formaldhyde)ISO 9001 (Quality Mangement System)ISO 14001 (Environmental Management System)ISO 45001 (Ocupational helth & safety management system) Approved make or equivalent
223	Round - 1500mmdia
224	Hexagon - 750mm one side
225	Triangular - 1500 mm one side
226	Furniture
227	Reception desk in lift lobby
228	Size : 1200 x550 x 750mm & 1050mm(H)
229	Fabricating and fixing ofa tableas per details indicated below
230	Providing and fixing of reception desk lower level formed out of 18 mm plywood with soffit pvc panelling for front and side cladding as indicated in the table view and all verticals and side panels to be of the same.All connections and inserts to be carpentered as per details and complete in all aspects.Top to have laminate finish as indicated in the view.
231	The table shall have suspended CPU stand as per details and approval.
232	Soft seating - Supply & Fixing of upholstered sofa seater as per requirements with high density Memory foam and leatherette upholstery as per approved sample. Frame work to be made with sold wood frame.
233	Single seater
234	L-shaped sofa of size - 2.65 m x 2 m as indicated in the plan.
235	Supply and fixing of coffee/ side / centre table as per requirements
236	Size - 450 x 450 mm
237	Size - 900 x 450 mm
238	Civil and related works
239	FLOORING AND CLADDING WORKS
240	Note:
241	Rates quoted in the following items shall include cost of all surface/substrate preparation, base plaster coat in the case of wall cladding/dado works, protection of flooring by providing a polythene sheet and a layer of POP.Rates to including carrying out works on all levels and heights, cartage, wastage etc.
242	Basic rates shall be the cost of material at suppliers place without taxes. Taxes, wastage up to 10%, carting, transport to site, labour for unloading, stacking, laying, cleaning and grouting etc all complete of the following items is to be taken by the contractor and added to basic price for quoting overall rate.
243	Providing and applying sample for approval to be carried out site level at no extra cost
244	I) Granite - Rs. 3000 per sqm
245	II) Ceramic tiles - flooring - Rs. 550 / sqm
246	iii) Ceramic tiles dado - Rs. 650 /sqm
247	iv) Vitrified tiles - Rs. 850 /sqm
248	v) Marble- Rs. 6500 /sqm
249	A maximum of - or + 5% variation is acceptable in basic rates indicated above.
250	Granite Stone on Counters
251	Providing and laying 3/4\" thick Granite Stone Slabs on counters, shelves, sills, and facias, laid on a 3/4\" thick bed of 1:4 Cement Mortar (1 Cement : 4 Coarse Sand), jointed with cement slurry mixed with pigment to match the shade of granite including mirror polishing, rounding off edges, edge-polishing etc. (Allow necessary cut-outs for fixing wash basin, pipes, waste couplings etc.)
252	Providing and laying in floors 20 mm thick pre-polished granite slabs over a bed of 40mm - 50 mm thick bedding mortar 1:4 (1 cement : 4 coarse sand) jointed with white cement slurry mixed with pigments as per approved colour.
253	Same as above but in skirting, risers and dado. Rate to include 6 mm edge chamfering wherever desired
254	Same as above but in treads etc. Rate to include half round nosing, edge polishing, making grooves as desired
255	Extra over as item \"a\" and \"c\" but with \"leather\" finished granite.
256	Vitrified tile flooring- laticrete grout
257	Same as item no 1.2 but for vitrified tile flooring of size 600 x 600 mm, 12 mm thickness anti-skid tiles
258	Same as item no 1.2 but for vitrified tile flooring of size 600 x 600 mm, 15 mm thickness anti-skid external grade full body tiles
259	Same as item 1.3 but for vitrified tile wall cladding of min size 300 x 600 mm, 12mm thickness
260	Demolition of existing walls
261	Demolition of existing walls on existing 6th floor - Rate to include demolition w/o any damage to any other other item and existing floor. Rate also to include carting away the debris to GF and to some other location as approved by us . Debris to be cleared from GF on the same day.
262	Core cutting to be done for waste water pipes.
263	100 Dia core cutting to be carried out in the site based on the location of the waste water drain outlets. The location to be marked and approval to be sought from the base builder prior to the commencement of the process of core cutting- Hilti core cutting system or equivalent
264	General design specifications and precautions Location and scanning: Before any cutting, use a ground penetrating radar (GPR) or a cover meter to precisely locate all embedded elements, including reinforcing bars, post-tensioning cables, and electrical conduits. Cutting post-tensioning cables is extremely dangerous and can cause catastrophic structural failure.Avoid critical areas: Core cuts should be avoided in high-stress zones of structural elements, such as:Beams: Do not cut cores through beams.Columns: Never core-cut through structural columns.Near supports: Avoid drilling close to beam-column joints, column-slab junctions, or other support locations, as these are subject to high shear forces.Size limitations:The diameter of the core cut should be as small as possible.A common standard for coring for strength testing requires the core diameter to be at least three times the maximum size of the concrete aggregate.Structural analysis: A structural engineer must perform an analysis to confirm that the integrity of the wall or slab will not be compromised by the proposed opening. The analysis should consider the hole\"s size, location, and proximity to other openings. Specific guidelines for walls Load-bearing walls: Cutting cores in load-bearing walls is especially critical and may require a review of the entire wall\"s load-carrying capacity. Reinforcing the wall may be necessary.Shear walls: Core cutting in shear walls, which are designed to resist lateral forces from wind or earthquakes, is highly discouraged. A structural engineer must be consulted for any modifications to these elements.Rebar clearance: The core must be drilled to avoid all reinforcing steel. If a rebar is inadvertently cut, a structural engineer must be notified immediately to design a repair or reinforcement solution. Specific guidelines for slabs Slab thickness: Consider the slab\"s thickness in relation to the core diameter. A deep, large-diameter core cut can significantly reduce the slab\"s flexural capacity.Pre-stressed/post-tensioned slabs: It is extremely hazardous to core-cut into a pre-stressed or post-tensioned slab without expert supervision. Damage to tendons can cause the structure to fail.Multiple holes: If multiple cores are required, they must be spaced far enough apart to prevent a reduction in the concrete\"s strength between them. A structural engineer should approve the spacing.Mid-span vs. supports: When core cutting is necessary, it is generally safer to make the cut at the centre of the slab, away from the support areas where bending moments and shear forces are typically highest. Repair and reinstatement Fill materials: After the core cut is completed, the hole must be filled with a non-shrinkage, high-strength grout or concrete. A bonding agent is often applied before filling to ensure a strong connection with the existing concrete.Surface preparation: Before filling, clean and roughen the surfaces of the core hole to ensure a good bond.Reinforcement replacement: If a rebar was cut, additional reinforcing may be required, such as bonding steel plates or using fiber-reinforced polymer (FRP) wraps, following the engineer\"s specifications.Preventing moisture intrusion: Proper repair is essential to prevent moisture from entering the concrete and causing corrosion of the rebars.
265	Aerocon panel- 75mm thick, A sandwich panel of two fiber-reinforced cement sheets enclosing a light weight concrete core composed of Portland cement and Fly-ashFully cured at factory, with a Unique “Tongue and Groove” jointing system. Rate to include patty and two coats of acrylic emulsion paint finish as per approved shade. Rate to include basic MS structure anchor bolts, scaffolding and erection. Rate to also include MS frame work around doors, windows and wall openings for services etc.
266	Materials & CompositionFace Sheets: Two layers of fiber-reinforced cement sheets. Core: Lightweight concrete made from Portland cement, binders, fly ash, fibers, and mineral aggregates. Key SpecificationsThickness: Available in standard thicknesses -75mm. Dimensions:Width: Typically 600mm. Height: 2.4mWeight: Around 58 kg/sqm, depending on the thickness. Thermal Conductivity: Around 0.17-0.22 W/mK. Axial Load/Meter Width: Can support loads of approximately 55-85 KN/m. Performance & FeaturesFire Resistance: Certified for fire resistance, providing a significant safety rating. Thermal & Acoustic Insulation: Offers good sound and thermal insulation properties. Water & Termite Resistance: Provides excellent resistance to water and termites. Dry Wall System: Designed for dry wall partition construction, eliminating the need for wet trades. Eco-Friendly: Made with recyclable materials and considered a green building material. Quick Installation: The interlocking tongue and groove system allows for fast and easy installation. Long Lifespan: Properly installed panels can last for over 50 years.
267	Plastering
268	Plasters to be prepared with Cement Mortars only with specified composition of cement and sand. Rates to include application on all type of surfaces, at all levels. Allow for p&f galvanized chicken mesh, min. 300mm wide, 24 SWG, 12mm size at junctions of brick and concrete members. Mesh to be properly stretched and nailed ensuring equal thickness of plaster on both sides of the mesh.No separate payment shall be made for providing and fixing chicken mesh. Make sufficient allowances for preparation of surface, providing necessary plaster grooves, making adequate keys, making drip-moulds to design etc., complete. Rate to include scaffolding for plastering up to 4 m height from the nearest slab level
269	Plastering - On walls and ceiling. Rate to include any surface preparation etc. all complete.
270	Providing and laying ½\"-3/4\" thick plaster of 1:4 Cement Mortar (1 Cement : 4 Fine Sand) on all internal vertical surfaces and wherever specified. For surfaces requiring thick plastering (like the uneven side of 4½\" thick brick masonry wall) , a preliminary coat may be applied of suitable thickness, allowed to set about 6 hours before application of the final coat.
271	Waterproofing of RCC slabs
272	Providing and applying Chemical waterproofing treatment using Sika Plastocrete or equivalent system in areas where toilets and other wet areas are being created. Rate to include dismantling existing screed/ flooring, surface preparation of mother slab, laying fresh screed to create slope, applying waterproofing system as per manufacturer\"s specifications and preparing the surface to received floor finish. Rate to include pond testing and making good any damages if leaks are found. - As per Architects approved make and Method statement for the works shall be submitted/ obtain approval prior to commencement of works.
273	Concrete screed flooring 75mm thick
274	Providing and laying 75mm thick 1:2:4 Cement Concrete (Indian Patent Stone with 1 Cement : 2 Coarse Sand : 4 graded stone aggregate of 20 mm and down gauge) laid in two layers, under layer of 40mm thick cement concrete 1:2:4 and top layer with 12mm thick with metallic concrete hardener of approved quality mixed in the ratio as specified by the manufacturer. Rate to include providing slope as desired, finishing smooth, curing 7days, watering, cleaning etc. complete. Hand held power trowel to be used for levelling.
275	MASONRY WORK & PLASTER
276	Brickwork in Superstructure
277	Brickwork of 9\" thickness
278	Providing and laying brick masonry above plinth for superstructure, for walls, pillars, parapet, cabins, architectural elements and other similar locations etc., in 1:6 Cement Mortar (1 Cement : 6 Coarse Sand by volume) in true line, level and plumb, including raking the joints up to 20 mm depth, rubbing and cleaning the surface, with necessary scaffolding, curing,soaking & the bricks adequately before construction, complete as directed and specified. Well burnt 1st class table moulded, good quality approved bricks
279	Exposed brickwork 9\" thick
280	Half brick partition walls
281	Providing and laying 4½\" thick half brickwork in partition walls,fins, parapets, architectural elements etc., with well burnt 1st class table moulded, good quality approved bricks in 1:4 Cement Mortar (1 Cement : 4 Coarse Sand by volume) including providing 2 Nos., 6 mm Dia.,FE 500 MS ribbed bars at every 4th course, including soaking the bricks in water adequately and drying, scaffolding, curing, rubbing the surface, raking out the joints etc., complete as directed and specified for walls, parapet, platform supports etc., at all floor levels.
282	Rcc counters for wash basins & benches
283	100 MM thick M25 Grade RCC counter with single matt 8 - 10 Dia steel reinforcement FE 500 to be cast at site as per sizes indicated in the drawings. 4½\" Brick wall under counter support to be considered. Quantity will be covered in item 12c. Providing, installing and de-shuttering Formwork with ordinary finish with plywood / steel for all in-situ concrete members as per technical specifications including strutting, staging, propping, supports, bracings, scaffolding single stage or multistage for locations and levels. Minimum 7 days of curing time to be considered.
284	Pergola covered structure for outdoor canteen in open terrace.
285	The glass skylight shall consist of a 13.52 mm thick laminated glass panel system, comprising 6 mm thick clear toughened glass + 1.52 mm PVB interlayer + 6 mm thick clear toughened glass, supported on a mild steel (MS) structural framework integrated with a pergola system and finished with powder coating. The MS structural framework shall be fabricated using 75x100x3 mm thick box sections for secondary members and 200x200 mm box sections for columns or as per structural design. The entire MS structure shall be fabricated and assembled at site, and fixed to the RCC slab or beam using base plates, anchor bolts, and neoprene isolation pads to allow for thermal expansion and minimize corrosion risk. All MS sections shall be treated with one coat of zinc-rich epoxy primer (minimum 40 microns DFT), followed by two coats of PU paint (minimum 100 microns total DFT), or hot-dip galvanized if exposed. The glass panels shall be secured using a two-way aluminium pressure plate glazing system, with all joints sealed using structural silicone and EPDM flashings to ensure weatherproofing. The skylight shall be installed at a minimum slope of 5 degrees to ensure proper drainage, with integrated aluminium perimeter flashings and a concealed gutter system provided to prevent water ingress and manage runoff. The entire system shall be designed to withstand wind and live loads in accordance with IS 875, with structural deflection limited to L/175 or less. All materials and workmanship shall conform to relevant Indian Standards, including IS 2062 for steel, IS 2553 for safety glass, and IS 16231 for structural glazing systems.
286	Rate to include access ladder as per safety standards to the top side of the pergola structure. Hook arrangement to be provided for locking it into the framework for secure access to the surface.Ladder to be provided with harness anchorage system.
287	Metal puff infill panel
288	50 mm thick partition- Metal sandwich panels with PU Foam insulation - Roof infill panels
289	TECHNICAL SPECIFICATION OF DOUBLE SKIN FACTORY INSULATED PUF PANEL
290	MONOWALL 50mm from Metecno make or equivalent.
291	External steel in 0.5mm thick (TCT) PPGI Z120GSM, 280-330 Mpa, groove in 2.5mm depth spaced at 62.5mm internval.External coating in RMP and External colour in RAL9002 shadeCore Insulation in CFC / HCFC[ ZERO ODP] Free PUF, Density 40+2 Internal steel in 0.5mm thick (TCT) PPGI Z 120GSM, 280-330 Mpa, groove in 2.5mm depth spaced at 62.5mm internval.External coating in RMP and External colour in RAL9002 spaced at 62.5mm internval.External coating in RMP and External colour in RAL9002 shadeEffective cover width of the panel will be 1000mmThickness of the panel 50+2mmThermal Transmittance [ U ] : 0.41Watt / m2 0CThermal Resistance [R] : 2.44 m2 0C / Watt
292	Rate to include erection, scaffolding, necessary supports above false ceiling and from the true ceiling, applying sealant in all the joints and at junctions.
293	Supply and installation of out door grade PVC Garden Lattice Plastic (PVC, HDPE) Standard Panel Size: 4 ft. x 8 ft.Thickness: Often 5mmMaterial: Polyvinyl chloride (PVC) or High-Density Polyethylene (HDPE)Durability: Weather-proof, resistant to rot, rust, and warping; can last for yearsColores: Green, white, red, ivory, blueMaintenance: No painting required
294	Rate to include fixing along the bottomportion of the metal pergola with appropriate framework as per standards.
295	Same as above but to be erected along the vertical surface along with MS framework of 50 x 50 mm MS channels as an enclosure for the A/C outdoor units to be installed in the terrace level. Height of the panels to be 1800 mm highOpenable panel to be provided for access into the internal unit space.
296	Anti Bird Nets for BalconiesSupply & installation of Anti bird nets made of 2.5mm thick nylon, providing strong protection against birds while ensuring visibility and airflow. Ideal for urban settings, To be installed on to the metal pergola structure with appropriate fasteners and anchors as per standards.
297	Carrying out necessary rectification works in existing walls, floors, and ceilings to enable further works. Includes patching, levelling, trimming, minor plaster repair, crack filling, surface preparation, and other small civil touch-ups as required for smooth execution of subsequent works. All complete as directed by Engineer-in-Charge.
298	TERRARIUM BOQ
299	Ultra clear - Toughened Glass
300	An ultra-clear terrarium tank with a door offers crystal-clear visibility and easy access for maintenance. Made from high-transparency glass, it enhances the natural beauty of plants and décor while the built-in door allows convenient care and ventilation, creating a perfect environment for a thriving ecosystem. (16x3x7 feet)
301	Exhaust Fan, Blower& Grunfos Pump
302	Wooden work with Granite Base
303	Horti Grade Grow Light-35W
304	Boost plant growth with our Full Spectrum Grow Light, designed to mimic natural sunlight. Perfect for terrariums, and indoor gardens, it enhances photosynthesis, promoting healthier, more vibrant plants. Energy-efficient, durable, and ideal for all growth stages.
305	Automated Sprinkler + Drip system
306	An automated sprinkler and drip system in a riparium ensures precise and efficient watering by combining fine misting for humidity control with targeted drip irrigation for plant roots. This system maintains optimal moisture levels, reduces manual effort, and promotes a healthy, self-sustaining ecosystem.
307	Stump wood and Detailing Wood
308	Stump wood is a natural hardscape element used in terrariums to create realistic, forest-like environments. It provides surfaces for plant attachment, enhances the aesthetic appeal while contributing to the ecosystem’s biological balance.
309	Horti Grade Harscape Materials
310	Horti-grade expanding foam is a plant-safe, waterproof foam used for creating naturalistic backgrounds and structural support in ripariums and terrariums. It securely holds plants, rocks, and driftwood while promoting moss and epiphyte growth, enhancing both aesthetics and ecosystem stability.
311	Natural Detailing Rock
312	Enhance your riparium with natural, mineral-rich rocks. These rocks help maintain stable water parameters by providing essential minerals and a natural habitat for fish and invertebrates. Durable, aesthetically pleasing, and safe for aquatic life.
313	Pasting Kit (Cable Tie, Cyanoacyrlate Glue , Garden Tape)
314	Ensure secure and durable bonding with our pasting kit, specially designed for aquariums and terrariums. Ideal for assembling glass, acrylic, or hardscape elements, it provides a strong, waterproof seal. Easy to use, long-lasting, and safe for aquatic environments.
315	Terrarium Soil
316	Terrarium soil is a well-draining, nutrient-rich substrate designed to support plant growth in enclosed ecosystems. It typically consists of organic matter, charcoal, and aerating materials like sand or perlite, ensuring proper moisture retention, root health, and long-term sustainability for terrarium plants.
317	Exotic Rainforest Plants
318	Exotic rainforest plants bring lush, vibrant greenery to ripariums and terrariums, mimicking natural jungle ecosystems. These plants, including bromeliads, orchids, ferns, and anthuriums, thrive in high humidity and indirect light, adding rich textures, colours, and biodiversity to the environment. Includes Miniature trees
319	Live Moss
320	Natural Forest Vibe: Moss creates a lush, green carpet that mimics the look of a forest floor, enhancing the immersive feel of the terrariumHumidity Regulation: Moss retains moisture, helping to maintain high humidity levels essential for a terrarium.
321	Sphagnum Moss & Moss media
322	Lava chips are lightweight, porous volcanic rocks used in terrarium for filtration, drainage, and aesthetics. Their porous structure promotes beneficial bacteria growth, improves water circulation, and enhances substrate aeration, supporting a healthy and balanced ecosystem.
323	Drainage Layer Leca Balls + Felt
324	A drainage layer with LECA balls and felt is essential for maintaining proper moisture levels in terrariums. LECA (Lightweight Expanded Clay Aggregate) provides aeration and prevents waterlogging, while the felt layer acts as a barrier, keeping soil separate from the drainage layer to ensure healthy root growth and a balanced ecosystem.
325	Drain cell
326	Drain cells 5mm promote root circulation and prevent root damage, also used for drainage purpose
327	Fertilizers
328	Components of a Starter Pack Fertilizer Kit1. Macro-Nutrients2. Micro-Nutrients3. Worm Castings4. Moss-Specific Fertilizer5. Epiphyte Fertilizer6. Substrate Enhancers
329	Maintenance Kit
330	Includes essential tools and consumables required for routine upkeep, cleaning, and minor adjustments to ensure the system remains in optimal working condition.
331	3D Printing, Designing, Painting & Installation
332	Including all materials, labour, tools, and incidental charges complete.
333	Installation Labour
334	Charges for skilled and unskilled labour for positioning, assembling, and complete installation at site, including all tools and tackles
335	Transport
336	Cost of safe handling, packing, loading, unloading, and delivery of all materials to site, including all charges, labour, and incidental expenses complete.
337	Design & Installation
338	Including concept development, drawings, detailing, labour, materials, supervision, and complete implementation at site.
339	Supply and fixing of base box to conceal and support the complete setup of the terrarium unit. Boxing to be done with BWR grade water proof plywood of 19 mm thickness and aluminium framework of 50x 50 mm sections for internal support.
340	Storage in pantry - 600mm high, 900mm deep with granite top - Providing and fixing in position storage made of waterproof ply with 20mm thk. polished granite top with edge as per profile in drawing. storage box construction same as item F1.. Elevation area considered for quantity measurement.
341	BOQ 9 - MODULAR
342	LINEARE WORKSTATION: 1200 X 550 X 745 HT
343	L-SHAPE WORKSTATION: 1350/1350 X 600 X 745 HT
344	System : League Plus or equivalentTable top : 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Understructure: Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Leg Modesty : 0.8mm thick CRCA sheet, 450mm Height with powder coated finish and Perforation at 400mm Ht. Understructure design is robust and very Sturdy enough with required neccessary Brackets.Modesty : modesty made up of CRCA 0.8mm sheet with double bend on all sides and for back to back workstation modesty made up of CRCA 0.8mm thick confirming to IS 513: 2008 with powder coated finish up 40 to 60 Micron at 300mm Ht.Main Privacy Screen : 18mm thick Partition considering the features of Magnetic & Fabric of 455mm Height feasibility. 18mm raw particle board. Complete screen periphery is covered by 22mm thick aluminum extrusion (6063-T6) Frame powder coatedfinished in 40 to 60 micron. Aluminium privacy panel section is constructional member of understructure shall be made of Aluminium extrusion confirming the IS 733:1983.Screen is supported by GI Stud which will be mounted on Aluminum section. Screen height will be 455mm above work-top, length will be 150mm less than work-top length. Wire Management: Electrical wires shall be carried from vertical duct or Electrical Legs from floor. Horizontally wire shall float in 105x130 mm cable tray for one sided workstation and 220x130mm cable tray for back to back workstation. Cable tray shall be made of 0.8mm CRCA sheet confirming to IS 513:2008. Horizontal 1 Tier Triangular Cable tray (wire carriers) are made of CRCA & fixed to the understructure below worktop with specially designed brackets. Cable tray will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.
345	PRELAM PEDESTAL : 400 X 450 X 621 HT
346	PRELAM 3 DRAWER (2B+1F) PEDESTAL UNIT 400Wx450Dx621H (With Castor) - madeup of 18mm thick Prelaminated Particle Board with PVC Edge band finish and the telescopic slides for mobility of drawers and filers. The drawer is made up of 18 mm thick PPB.Centre Locking Mechanism considered. Side Finger Groove Handle is considered for Seamless Look.-- MS & CRCA sheet items are to be sourced from TATA/Jindalor equivalent
347	Cabin table : 1800 x 600 x 745ht, SIDE STOARGE : 950 X 450 X 750 HT
348	System : League plusor equivalentTable top : 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Understructure : Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Leg Modesty : 0.8mm thick CRCA sheet, 450mm Height with powder coated finish and Perforation at 400mm Ht. Understructure design is robust and very Sturdy enough with required neccessary Brackets.Modesty : modesty made up of CRCA 0.8mm sheet with double bend on all sides and for back to back workstation modesty made up of CRCA 0.8mm thick confirming to IS 513: 2008 with powder coated finish up 40 to 60 Micron at 300mm Ht.Wire Management: Electrical wires shall be carried from vertical duct from floor. Vertical Diuct will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.STORAGE UNITSTOP :18mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).CARCASS & SHUTTER : 18mm thick prelaminated board with PVC Edge band with openable ShutterBACK: 18mm thick prelaminated board with PVC Edge band.LOCK : Regular lock Chamfer handles.
349	Cabin table : 1800 x 600 x 745ht, SIDE STOARGE : 950 X 450 X 750 HT
350	System : League plusor equivalentTable top : 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Understructure : Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Leg Modesty : 0.8mm thick CRCA sheet, 450mm Height with powder coated finish and Perforation at 400mm Ht. Understructure design is robust and very Sturdy enough with required neccessary Brackets.Modesty : modesty made up of CRCA 0.8mm sheet with double bend on all sides and for back to back workstation modesty made up of CRCA 0.8mm thick confirming to IS 513: 2008 with powder coated finish up 40 to 60 Micron at 300mm Ht.Wire Management: Electrical wires shall be carried from vertical duct from floor. Vertical Diuct will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.STORAGE UNITSTOP :18mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).CARCASS & SHUTTER : 18mm thick prelaminated board with PVC Edge band with openable ShutterBACK: 18mm thick prelaminated board with PVC Edge band.LOCK : Regular lock Chamfer handles.
351	CAFÉ TABLE : 2400 X 800 X 750 HT
352	CAFÉ TABLE : 4200 X 900 X 750 HT
353	CAFE TABLE ;System : Cafe tableTabletop: 25mm thick Post-laminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Leg : Metal powder coated spider legs - MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.
354	ROUND DISCUSSION TABLE : 1200 DIA X 750 HT
355	ROUND DISCUSSION TABLE : 1500 DIA X 750 HT
356	System : League plusor equivalentTabletop: 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Leg : Metal Powder Coated curve Leg - MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Wire Management: Electrical wires shall be carried from vertical duct from floor. Vertical Diuct will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.
357	MEETING TABLE : 1200 X 750 X 745HT
358	System : League plusor equivalentTabletop: 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Leg : Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Wire Management: Electrical wires shall be carried from vertical duct or Electrical Legs from floor. Horizontally wire shall float in 105x130 mm cable tray for one sided workstation and 220x130mm cable tray for back to back workstation. Cable tray shall be made of 0.8mm CRCA sheet confirming to IS 513:2008. Horizontal 1 Tier Triangular Cable tray (wire carriers) are made of CRCA & fixed to the understructure below worktop with specially designed brackets. Cable tray will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.
359	MEETING TABLE : 1350X 750 X 745HT
360	System : League plusTabletop: 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Leg : Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Wire Management: Electrical wires shall be carried from vertical duct or Electrical Legs from floor. Horizontally wire shall float in 105x130 mm cable tray for one sided workstation and 220x130mm cable tray for back to back workstation. Cable tray shall be made of 0.8mm CRCA sheet confirming to IS 513:2008. Horizontal 1 Tier Triangular Cable tray (wire carriers) are made of CRCA & fixed to the understructure below worktop with specially designed brackets. Cable tray will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.
361	MEETING TABLE : 3000 X 1200 X 745HT
362	System : League plusor equivalentTabletop: 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Leg : Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Wire Management: Electrical wires shall be carried from vertical duct or Electrical Legs from floor. Horizontally wire shall float in 105x130 mm cable tray for one sided workstation and 220x130mm cable tray for back to back workstation. Cable tray shall be made of 0.8mm CRCA sheet confirming to IS 513:2008. Horizontal 1 Tier Triangular Cable tray (wire carriers) are made of CRCA & fixed to the understructure below worktop with specially designed brackets. Cable tray will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.
363	EXECUTIVE CABIN TABLE : 2000 X 900 X 745HT
364	System : League plusor equivalentTabletop: 25mm thick Prelaminated Particle Board confirming to IS12823:1990 with Flat PVC edge band. All the edges and exposed surface shall be edge banded with PVC lipping (color to be matched with the laminate).Leg : Metal Leg with 1.6 mm thick CRCA sheet, 40x40 mm Square MS pipe with M10 leveller at the ends . Legs shall be fitted to the ground with M10 screw leveller with the height adjustment up to 12mm to 15mm. Cross member are made of 50mm x 25mm x 1.2mm MS sections with powder coated finish confirming to IS 13871:1993. Cross members shall be mounted by end brackets. Cross member end bracket shall be made of 3mm thick IS 513: 2008 CRCA sheet with powder coated finish up 40 to 60 Micron DFT.Wire Management: Electrical wires shall be carried from vertical duct or Electrical Legs from floor. Horizontally wire shall float in 105x130 mm cable tray for one sided workstation and 220x130mm cable tray for back to back workstation. Cable tray shall be made of 0.8mm CRCA sheet confirming to IS 513:2008. Horizontal 1 Tier Triangular Cable tray (wire carriers) are made of CRCA & fixed to the understructure below worktop with specially designed brackets. Cable tray will be provided with separation tray for electrical and data wires. Provision for fixing Switch plates are provided in the cable tray for easy access through Aluminium Powder coated Access Flap with soft Closing mechanism of 450mm Lx145mm D. Switches to be mounted on Cable Tray Angular Surface for Easy use.
365	BOOK SHELF : 4080 X 600 X 750 HT
366	LOW HEIGHT STORAGE - 4425 X 600 X 500 HT
367	FULL HEIGHT STORAGE : 2800 X 600 X 2100 HT
368	FULL HEIGHT STORAGE : 2500 X 600 X 2100 HT
369	LOW HEIGHT STORAGE - 1200 X 600 X 750 HT
370	LOW HEIGHT STORAGE - 1440 X 600 X 750 HT
371	LOW HEIGHT STORAGE - 1705 X 600 X 750 HT
372	FULL HEIGHT STORAGE - 2080 X 600 X 2100 HT
373	LOW HEIGHT STORAGE - 3600 X 600 X 750 HT
374	LOW HEIGHT STORAGE - 5920 X 600 X 500 HT
375	FULL HEIGHT STORAGE - 3355 X 600 X 2100 HT
376	STORAGE UNITSTOP :18mm thick prelaminated board with PVC Edge band to all Exposed Area.CARCASS & SHUTTER : 18mm thick. prelaminated board with PVC Edge band with openable ShutterBACK: 18mm thick. prelaminated with PVC Edge band.LOCK : Regular lock Chamfer handles.
377	Electrical BOQ
378	Scope includes Testing and Commissioning of system with Preparation of \"As Fitted Drawings\" and submission of 3 Sets of hard copies and 1 Set of soft copy.
379	Erection Cost shall be included with all necessary accessories required for Erection in all aspects should be included in the Offer.
380	If any item is missed out, the tenderer is duty bound to quote for the same. The additional items shall be listed and quoted as an attachment with a covering note. Any claim for omissions after the contract is awarded shall be rejected.
381	Successful bidder to prepare the shop drawingsfor Client / Architect approval before deliver the materials and execute the works at site
382	LT Panel Board
383	Note: All bus bar sizes should be per tender only. All the panels will have to be design for 0.7Amps/Sq.mm for Aluminium and 1.2Amps/Sq.mm for Copper bus bar. Gland plates are required. Location of gland plate will have to be deciding by you according to suit the terminal of switchgears and suitable for the cables
384	All Incoming and Outgoing Switch Gears shall be with IBMS Connectivity for monitoring the ON / OFF / Trip Status
385	All Energy Meters shall be with IBMS Connectivity for monitoring the required data\"s
386	Main Panel Board
387	Supplying, erecting, fabricating, connecting and commissioning a floor mounted cubicle type Panel Board. The Panel Board shall be incorporated with the following:-
388	Cable Entry : Top
389	Incomer: 1No 400Amps TPN MCCB of 36kA(Ics) withstanding capacity with Adjustable Overload and Short Circuit Releases of LSIG breaker and Type 1 and 2 Surge Protection Device with digital energy meter with suitable CT and 400Amps Four Pole Auto Transfer Switch with Controller of Socomec make (or) equivalent…1No
390	Outgoing: 125Amps TPN MCCB of 25kA(Ics) withstanding capacity with Adjustable Overload and Short Circuit Releases…2Nos
391	63Amps TPN MCCB of 18kA(Ics) withstanding capacity with Adjustable Overload and Short Circuit Releases…12Nos
392	Note: The Withstanding capacity mentioned shall be Ics Only.
393	Busbar : Aluminium
394	Rating : 400Amps
395	The Phase Busbar shall be of 100x6mm. and the Neutral bar shall be of 50x6mm. The Earth Busbar shall be of 2Run 25x6mm
396	There shall be one set of Metering Compartment incorporated with the following:-
397	I) 3Nos Dual Core Cast Resin CTs of ratio 400 / 5Amps of Class 1.0 for metering and burden 10VA
398	ii) 1No Digital Multifunction Meter (Voltage, Current, Energy and Frequency) with Selector Switch
399	iii) OBO BETTERMAN Surge Arrestor
400	iv) RYB Indication lamp of LED cluster Type with Control Fuses shall also be provided.
401	Outgoing UPS Panel Board
402	Supplying, erecting, fabricating, connecting and commissioning a floor mounted cubicle type Panel Board. The Panel Board shall be incorporated with the following:-
403	Cable Entry : Top
404	Incomer: 1No 125AmpsTPN MCCB of 25kA(Ics) withstanding capacity with Adjustable Overload and Short Circuit Releases of LSIG breaker Type 1 and 2 Surge Protection Device with digital energy meter…1No
405	Outgoing: 125Amps TPN MCCB of 25kA(Ics) withstanding capacity with Adjustable Overload and Short Circuit Releases…2Nos
406	63Amps TPN MCCB of 18kA(Ics) withstanding capacity with Adjustable Overload and Short Circuit Releases…5Nos
407	Note: The Withstanding capacity mentioned shall be Ics Only.
408	Busbar : Copper
409	Rating : 125Amps
410	The Phase Busbar shall be of 25x6mm. and the Neutral bar shall be of 25x6mm. The Earth Busbar shall be of 2Run 25x3mm
411	There shall be one set of Metering Compartment incorporated with the following:-
412	I) 3Nos Dual Core Cast Resin CTs of ratio 125 / 5Amps of Class 1.0 for metering and burden 10VA
413	ii) 1No Digital Multifunction Meter (Voltage, Current, Energy and Frequency) with Selector Switch
414	iii) OBO BETTERMAN Surge Arrestor
415	iv) RYB Indication lamp of LED cluster Type with Control Fuses shall also be provided.
416	MCB DBs
417	Supplying, fixing, connecting & commissioning the following MCB Distribution Boards fixed flush / Concealed with the wall or open on wall on an angle iron frame. cost of angle iron frame to be included. All MCB DBs shall have Double door and incoming adopter box (Powder coated) to receive wires in pipes / cables etc. The adopter box shall have a minimum height of 150mm. All wiring terminations shall be done through copper lugs cost to be included. All Outgoings to be identified on every MCB, and also ferrules to be provided
418	Vertical Distribution Board
419	4Way TPN Vertical MCB DB For Server Rooms Incomer: 125Amps TPN MCCB with 25kA(Ics) Withstanding Capacity with Adjustable Overload and short circuit relay with Surge Protection..1NoOutgoing: 63Amps TP+N MCB..3Nos 6-32Amps SP+N MCB..3Nos
420	Lighting Distribution Board
421	8Way TPN 7 Segment MCB DBIncomer: 63Amps 4P MCB... 1No. Outgoing: 63Amps DP, 30mA RCBO with Surge Protection Device Type 3 .. 3Nos6-32Amps SP MCB... 24Nos
422	Power Distribution Board for Small Power Socket Outlets
423	12Way TPN 7 Segment MCB DBIncomer: 63Amps 4P MCB... 1No. Outgoing: 63Amps DP, 30mA RCBO with Surge Protection Device Type 3 .. 3Nos6-32Amps SP MCB... 36Nos
424	Power Distribution Board for VRV Indoor Units
425	8Way TPN 3-Tier MCB DBIncomer: 63Amps 4P MCB... 1No. Outgoing: 63Amps DP, 30mA RCBO with Surge Protection Device Type 3 .. 3Nos6-32Amps SP MCB... 24Nos
426	UPS Distribution Board
427	12Way TPN 3 Tier MCB DB for Workstations Incomer: 63Amps 4P MCB…1No Outgoing: 63Amps DP, 30mA RCBO with Surge Protection Device Type 3 .. 3Nos 6-32Amps SP MCB… 36Nos.
428	4Way TPN 3 Tier MCB DB For Simulation Lab, HVAC System and Server RoomsIncomer: 63Amps 4P MCB…1No Outgoing: 63Amps DP, 30mA RCBO with Surge Protection Device Type 3 .. 3Nos 6-32Amps SP MCB… 12Nos.
429	Emergency Lighting Distribution Board
430	16Way SPN MCB DBIncomer: 40Amps DP, 30mA RCBO with Surge Protection Device Type 3 …1NoOutgoing: 6-32Amps SP MCB... 10Nos
431	MCB / FSU/ MCCB Control
432	Supplying, erecting, connecting and commissioning of 125Amps 4Plole MCCB of 25kA(Ics) withstanding capacity with adjustable overload and short circuit releases, with Weather proof enclosure on an angle Iron frame with necessary interconnections, cable box, brackets, screws, bolts, nuts, etc to complete the erection works for Incoming and Outgoing Control of 30kVA and 60kVA UPS System
433	Supplying, erecting, connecting & commissioning on weather proof enclosure with 63Amps 4 Pole 300mA RCBO and Phase Reversal Relay in MS Enclosure on an angle iron frame with necessary interconnections, cable box, brackets, screws etc. for VRV Outdoor Units
434	Supplying, erecting, connecting & commissioning on weather proof enclosure with 63Amps 4 Pole MCB on an angle Iron frame with necessary interconnections, cable box, brackets, screws, bolts, nuts, etc. to complete the erection works
435	Supplying, erecting, connecting & commissioning on weather proof enclosure with 40Amps Double Pole MCB on an angle Iron frame with necessary interconnections, cable box, brackets, screws, bolts, nuts, etc. to complete the erection works for Incoming and Outgoing Control of 6kVA UPS for Emergency Lighting Purpose
436	Supplying, erecting, connecting & commissioning on weather proof enclosure with 6Amps Double Pole MCB in MS Enclosure on an angle iron frame with necessary interconnections, Wire box, brackets, screws etc. for VRV Indoor Units (5Nos Hi-Wall Spilt and 2Nos Cassette Units)
437	Cables
438	Supplying, laying, connecting & commissioning the following 1.1KV Grade XLPE Insulated Underground cables with necessary clamps, screws, etc. inthe following methods:-
439	Laid in Buried Under Ground, clamped along with wall / column / laid in tray
440	4C 400 Sq.mm. Al
441	4C 70 Sq.mm. Cu
442	4C 35 Sq.mm. Cu
443	4C 16 Sq.mm. Cu
444	4C 10 Sq.mm. Cu
445	4C 6 Sq.mm. Cu
446	3C 10 Sq.mm. Cu
447	3C 4 Sq.mm. Cu - Flexible (Black colour for Raw and White colour for UPS Power)
448	3C 2.5 Sq.mm. Cu - Flexible (Black colour for Raw and White colour for UPS Power)
449	Supplying, terminating, connecting and commissioning the above Underground cables with Double compression type SIBG Cable glands. Thecost of earthing gland with copper strips / wires shall also be included. The cables shall be terminated with aluminium / copper lugs after crimping
450	4C 400 Sq.mm. Al
451	4C 70 Sq.mm. Cu
452	4C 35 Sq.mm. Cu
453	4C 16 Sq.mm. Cu
454	4C 10 Sq.mm. Cu
455	4C 6 Sq.mm. Cu
456	3C 10 Sq.mm. Cu
457	Mains Wiring
458	Note: All conduits above false ceiling shall be properly fixed on RCC Ceiling on 1.5mm thick brackets details to be furnished by successful bidder along with shop drawings
459	Power Wiring - Raw Power Socket Outlets
460	Note: All conduits above false ceiling shall be properly fixed on RCC Ceiling on 1.5mm thick brackets details to be furnished by successful bidder along with shop drawings
461	Note: Please get sample approval before dispatch the materials at site as well as specify on tender documents with respect to model name considered in commercial offer
462	Supplying, laying, connecting and commissioning 3Runs of 1.5Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral and earth) wires for continuous earthing in already laid Conduits concealed in floor / wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., for 6Amps Socket Raw Power Outlet - VAV Units
463	Supplying, laying, connecting and commissioning 3Runs of 2.5Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral and earth) wires for continuous earthing in already laid Conduits concealed in floor / wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., for 6Amps Socket Raw Power Outlet -VRV Indoor Units
464	Supplying, laying, connecting and commissioning 3Runs of 2.5Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral and earth) wires for continuous earthing in already laid Conduits concealed in floor / wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., for 6Amps Socket Raw Power Outlet - General Purpose
465	Supplying, laying, connecting and commissioning 2Runs of 4Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral) with 1Run of 2.5Sqmm. PVC Insulated multistranded FRLS copper conductor wires for continuous earthing in already laid Conduit concealed in wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., for 6/16Amps Socket Raw Power Outlet
466	Supplying, laying, connecting and commissioning 2Runs of 6Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral) with 1Run of 2.5Sqmm. PVC Insulated multistranded FRLS copper conductor wires for continuous earthing in already laid Conduit concealed in wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., for 25Amps Socket Raw Power Outlet
467	Supplying and fixing 6Amps Switched Socket combined in Manufacturer\"s mounting box fixed flush with the wall for VRV Indoor and VAV Units
468	Note: In one Circuit there shall be 1Set of 6Amps Socket shall be wired
469	Supplying, fixing, connecting & commissioning 1x6Amps Socket with 1x6Amps Switch housed in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with necessary accessories such as screws bolts & nuts etc.
470	Note: In one Circuit there shall be 8 to 10 Sets of 6Amps Socket shall be wired
471	Supplying, fixing, connecting & commissioning of 1x6/16Amps Socket with 1x16Amps Switch housed Weather Proof enclosure in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with necessary accessories such as screws bolts & nuts etc.
472	Note: In one Circuit there shall be 2Sets of 16Amps Socket shall be wired
473	Supplying, fixing, connecting & commissioning 1x6/16Amps Socket with 1x16Amps Switch housed in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with necessary accessories such as screws bolts & nuts etc.
474	Note: In one Circuit there shall be 2Sets of 16Amps Socket shall be wired
475	Supplying, fixing, connecting & commissioning of 1x25Amps Socket with 1x25Amps Switch housed Weather Proof enclosure in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with necessary accessories such as screws bolts & nuts etc.
476	Note: In one Circuit there shall be 1Sets of 25Amps Socket shall be wired
477	Supplying and laying the 25mm. Dia Heavy-duty PVC conduits concealed in ceiling / wall / floor with necessary accessories to complete the erections works with 1Run 16 SWG GI Fish wire.
478	Supplying, laying of 25mm Dia MS flexible hose laid in partitions with necessary supports clamps, screws etc.
479	Supplying, laying 25mm. Dia MS Conduits laid in open fashion above false ceiling, wall / partitions with necessary clamps, screws etc.
480	Light Point Wiring
481	Note: All conduits above false ceiling shall be properly fixed on RCC Ceiling on 1.5mm thick brackets details to be furnished by successful bidder along with shop drawings
482	Note: Please get sample approval before dispatch the materials at site as well as specify on tender documents with respect to model name considered in commercial offer
483	Supplying, wiring, connecting & commissioning thelight points with 3Runs of 1.5Sq.mm. PVC insulatedmultistranded Copper Conductor FRLS wires (One each for Phase, Neutral and earth) in already laid MS Conduits concealed in wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., including supplying and fixing 6Amps Switch in manufacturers mounting box fixed flush with the wall / Partitions. The maximum length will be 10.0Mtrs from switch board to 1st light point
484	One Light Controlled by one Switch - Primary Point
485	Supplying, wiring, connecting & commissioning the light points with 3Runs of 1.5Sq.mm. PVC insulated multi stranded copper Conductor FRLS wires (One each for Phase, Neutral and Earth) in already laid MS Conduits concealed in wall / ceiling or laid in open fashion above false ceiling with necessary clamps, screws etc. for additional points. The additional points will have to be wired from the first point mentioned under Item under Item No.07.01.01 The maximum length will be 5.0 Mts. for each additional point.
486	Supply, Laying, Connecting & commissioning of 3Runs of 2.5 Sq.mm. PVC insulated multistranded Copper Conductor FRLS wires (One each for Phase, Neutral and Earth) in already laid MS Conduits concealed in wall / ceiling with necessary Accessories from LDB to First Switch Board and Switch Board to Switch Board.
487	Supply, Laying, Connecting & commissioning of 3Runs of 1.5 Sq.mm. PVC insulated multistranded Copper Conductor FRLS wires (One each for Phase, Neutral and Earth) in already laid MS Conduits concealed in wall / ceiling with necessary Accessories for additional Lenths if point wiring exceeds more than 10.0Mtrs
488	Supplying, laying of 25mm Dia MS flexible hose laid in partitions with necessary supports clamps, screws etc.
489	Supplying, laying 25mm. Dia MS Conduits laid in open fashion above false ceiling with necessary clamps, screws etc.
490	UPS Wiring
491	Note: Please get sample approval before dispatch the materials at site as well as specify on tender documents with respect to model name considered in commercial offer
492	Supplying, laying, connecting and commissioning 3Runs of 2.5Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral and earth) wires for continuous earthing in already laid Conduits concealed in floor / wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc. for 6Amps Socket UPS Power Outlet
493	Supplying, laying, connecting and commissioning 2Runs of 4Sq.mm PVC Insulated multistranded copper conductor FRLS wires (One each for Phase, Neutral) with 1Run of 2.5Sqmm. PVC Insulated multistranded FRLS copper conductor wires for continuous earthing in already laid Conduit concealed in wall / partitions or laid in open fashion above false ceiling with necessary clamps, screws etc., for 6/16Amps Sockets
494	Supplying, fixing, connecting & commissioning of 1x6Amps Multi-Pin UPS Sockets with 1x6Amps Switch housed in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with all other accessories to complete the erection works
495	Note: In one Circuit there shall be 2 to 8 Sets of 6Amps Switched Socket shall be wired
496	Supplying, fixing, connecting & commissioning of 2x6Amps Multi-Pin UPS Socket with 1x16Amps Switch housed in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with all other accessories to complete the erection works
497	Note: In one Circuit there shall be 4 Sets of 2x6Amps Socket shall be wired
498	Supplying, fixing, connecting & commissioning of 3x6Amps Multi-Pin UPS Socket with 1x16Amps Switch housed in Manufacturer\"s mounting box fixed flush with the wall (or) on partitions with all other accessories to complete the erection works
499	Note: In one Circuit there shall be 2Sets of 3x6Amps Socket shall be wired
500	Supplying, fixing, connecting & commissioning of 1 x 6/16Amps Switched Socket Combined in Manufacturer\"s mounting box fixed flush with the wall with all other accessories to complete the erection works

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tamil Nadu Tenders

Services Tenders

Space Planning and Designing Tenders

Interior Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Total Turnkey Interior Fit Out Works In The Eighth Floor (B- Block) Iitmrp, Chennai-Tamil Nadu

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Total Turnkey Interior Fit Out Works In The Eighth Floor (B- Block) Iitmrp, Chennai-Tamil Nadu

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us