|
| 1 | CIVIL WORKS |
| 2 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of Soil |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 4 | Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 5 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 6 | Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 7 | Steel work for purlin / single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 8 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800 x 800 mm |
| 9 | Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works |
| 10 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work |
| 11 | Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete. The item includes cost of all material & labour component,, as per the Architectural drawings, as per item description as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. |
| 12 | Providing indoor potted plants well developed from top to bottom in clay/ plastic/khurja pot including all necessary allied backups etc. complete as per specification and instruction of engineering in charge.-Snake plant |
| 13 | Providing and fixing in position, puff panelled roofing sheets of 40 mm thick PU Sandwich panel, Top sheet 0.5 mm, bottom 0.35 mm PGGI / PPGL including all necessary fixtures and adhesive. The rate shall be inclusive of any scaffolding or material lifting charges. Fixing operations of roof / floor panels shall be completed in all respect, including the selection of colour and type, as per drawings and specifications and under the overall direction of the Engineer-in-charge |
| 14 | Supplying and installation of moisture resistant/fire resistant 12 mm thick Heavy duty fiber cement board ( High pressure steam cured ) conforming to IS14862:2000 of category III type B as per standard sizes fixed with self-drilling / taping screws. Screws shall be of counter sunk rib head of 1.60mm to 4 mmthick of 8 to 10 gauge of length varying from 25 to 45 mm. |
| 15 | ELECTRICAL WORKS |
| 16 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group c |
| 17 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A |
| 18 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 19 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings) |
| 20 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required |
| 21 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 22 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 23 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 24 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole |
| 25 | Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI/painted MS saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required |
| 26 | Supply, laying / clamping, testing and commisioning of the following XLPE insulated PVC sheathed armoured heavy duty power cable conductor of best conductivity aluminium/Copper 1.1kV grade strictly conforming to IS:1554 (Part-I) 1964 of the following sizes in cable trench/cable tray /wall using factory made heavy gauge GI/painted MS clamps. Space between clamps not exceeding 60cms amd making good the damages colour washing etc as required and as instructed by engineer in charge. |
| 27 | Supply, laying / clamping, testing and commisioning of the following XLPE insulated PVC sheathed armoured heavy duty power cable conductor of best conductivity aluminium/Copper 1.1kV grade strictly conforming to IS:1554 (Part-I) 1964 of the following sizes in cable trench/cable tray /wall using factory made heavy gauge GI/painted MS clamps. Space between clamps not exceeding 60cms amd making good the damages colour washing etc as required and as instructed by engineer in charge |
| 28 | Supply and making end termination with brass compression gland, earth clip and aluminum lugs/ Cu lugs for following size of XLPE insulated and PVC sheathed aluminum/copper conductor cable of 1.1kV Grade as reqiured. |
| 29 | Supply and making end termination with brass compression gland, earth clip and aluminum lugs/ Cu lugs for following size of XLPE insulated and PVC sheathed aluminum/copper conductor cable of 1.1kV Grade as reqiured. |
| 30 | Supplying and fixing of following sizes HDPE along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required |
| 31 | Supply and install weatherproof electrical cabinets conforming to EN 60439-3, designed for high durability and safety with Class II insulation, IP65 ingress protection, and IK09 impact resistance. The enclosures shall be self-extinguishing with resistance to incandescent wire at 650 °C, suitable for indoor and outdoor environments. A 2-position rail system shall be provided for modular devices and moulded case circuit breakers, maintaining a 150 mm spacing between rails for efficient wiring and ventilation. |
| 32 | Supplying, installation, testing and commisioning of Linear LED Batten with a nominal system lumen output of 2000 lumens and a minimum system efficacy of 105 lm/W. System wattage should not exceed 20W. The luminaire shall have a rated system lifetime of 40,000 burning hours at L70. The luminaire should have a color temperature of 6500K and CRI>80. Driver of the luminaire shall have THD < 10% and PF > 0.95. The luminaire housing should be made of CRCA with a PC glossy diffuser. The driver shall comply to IEC 60598, IEC 62384 , IEC 61347-2-13, IEC 61547, EMI- CISPR15 standards. (Havells MakeLumiline Nxt Batten \"LUMILINEPLUSNEOBS20WLED840SPCSSIND (2ft. WH)\" or equivalent) |
| 33 | K-Lite surface mounted compact flexible linear LED lighting with system wattage of 9W/m. Beam angle 120° diffused. Luminaire housing and diffuser made of silicone, UV proof for true outdoor application. High light transmittance, environmental silicone material. Top bendable. Cut-able for flexible application. Even light distribution & no hot spots. Aluminium mounting profile / Flexible mounting channel for surface mounting on ceiling / wall / floor. Protection class IP67. Mechanical resistance IK08. Available colour temperature 3000K (Other CCTs on request), Colour rendering index (CRI)>80. Operating temperature range is from -15°C to +50°C. Constant voltage non integral power supply at 24Vdc assures safety. Luminaire dimension : 1000mm length x 15mm width x 15mm height. OEM Should have Inhouse NABL accredited lab. Suggested makes: K-LITE / Unilamp / Ligman |
| 34 | Supply,Installation, testing and commisioning of 5 star rated , BEE certified 24 to 26W, ceiling fan with BLDC motor,remote control for operation including installation of downrod and all accessories. The fan shall operate on a high-efficiency BLDC motor, offering six adjustable speed levels with low-noise performance. All functions, including speed control, light adjustment and timer shall be operable via a remote control. The installation shall include all accessories required for mounting and operation, and the unit shall be tested and commissioned in accordance with the manufacturer’s guidelines and relevant electrical standards to ensure full functionality and operational readiness. |
| 35 | Supply and laying the following sizes of strips laid 0.6 m below ground level including excavating trench of suitable size and refilling ,including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultan Please Enable Macros to View BoQ information |
