|
| 1 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it\"s ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product/ work refer Annexure \"A\" attached with this BSR |
| 2 | On board |
| 3 | Short point (up to 3 mtr.) |
| 4 | Medium point (up to 6 mtr.) |
| 5 | Long point (up to 10 mtr..) |
| 6 | Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works with Galvanized box of 1.2 mm thick with earth terminal with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet making connection , testing, etc. as required. . For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 7 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 8 | 25 mm |
| 9 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 10 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 11 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 Arating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work referAnnexure \"A\" attached with this BSR |
| 12 | Single pole MCB (With B/C curvetripping Characteristics) |
| 13 | 6 A to 32 A rating |
| 14 | Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .1200 mm Sweep BEE 3 Star rated (service value >=5.0 to<5.5 ) |
| 15 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin) ,Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 16 | 570mm (+/-10%) batten with min. lumenoutput 1000 lm |
| 17 | Supply , Installation, Testing and Comissioning of Inverter type Air Cooled Hi Wall split type Air conditioners with latest star rating system as per BEE amended upto date complete with Indoor unit(IDU), Out door unit (ODU), surface/ concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU), R-32/R-410Green Refrigerant, wireless Remote control, suitable for working between 230V +/- 10% with low & high voltage cutoff and 50 hz , single phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with thisBSR . |
| 18 | 1.0 TR ISEER not less then 3.8 |
| 19 | Supply & installation Conference Table size 1000L*6000*750H in mm, Table Top made of 36mm Thick Particle board Round Post form top With 2mm Thick PVC Edge banded Finish With As Per Approved Laminate Shade, Connection Tops of conference table made of MDF Board of size 600W x 600D x 25mm Round postform Pasted With 0.4mm Thick black PVC Membrane on Board, Gable - Ends of the table Made Of 25mm Thick PLPB twin Board designed with similar to the photograph, Modesty Panel Prime Quality 25mm Thick 718mm High PLPB Board Supported To Top & Gable ends, 7mm High PVC Buffers Screw With Gable-end, PVC Wire manager provide on top, 18mm thick PLPB cable tray should be provided below top, All Wooden Panels. Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment All Wooden Panels Prime Quality Board With ISI Marked. IS:12823:1990. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. As Direction by Engineer-in-Charge |
| 20 | Supply of visitor chair with PU arm MS Frame (with powder coated two or more coat painted, 25mm Round Pipe with 5.300Kg Per 20 Feet length) with 40 density Cushion set & back Matty cloth† of height 83cm seat 45cmX45cm height of seat 45cm as direction of Engineer incharge. |
| 21 | Almirah 3\"X6\" (Lockable Type-1) 78\" x36\"x18\" with 22 gauge whole body (5 nos partitions ) one portion will have provision of two lockers sample and colour to be approved by Engineer-in-charge |
| 22 | Providing and fixing S.S. Rod 30mm dia (304 grade ,16SWG) including brackets fixed with C.P. brass screws and rawl plugs, etc., wherever necessary complete two side central all fittings. |
| 23 | Supply & installation of Centre Table Overall Size 1215W X 605D X 450H mm, Table Top Made Of Veneer & Melamine polish, Inner material used in Table top is 18mm thickness commercial block board & prime quality veneer pasted on it with Melamine polish, Table Top Size 1215W X 605D X 18mm Thickness, Teak colour Veneer pasted on table top, Legs made up of solid teak wood material of size 60W X 60Dmm, Under structure Top Supported Panel Made Of Prime Quality Solid teak Wood material of size 60x20mm, complete structure are in Melamine polish, commercial Board Use Prime Quality With ISI Marked , All Wooden Panels Cleaning Corner Knitted Finish , Wooden Panel Joint Leg To Leg Supported To Top. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomicdesign. |
| 24 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer- in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessoriessuch as nuts, bolts, fasteners etc.). |
| 25 | Grade 304 |
| 26 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement: 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Jhunjhunu / Jalore(Red/Choclate/Black/Pink Colour) Please Enable Macros to View BoQ information |
