Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed. |
| 2 | Demolition of roofs, floor (other than ground floors), beams staircases, landing, chajjas & similar suspended work cement concrete (reinforced) complete all as specified and directed. |
| 3 | Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed. |
| 5 | Dismantling of stone slabs and tiles of any description or any thickness in floors, dado etc, laid bedded and pointed in any mortar, complete all as specified & as directed. |
| 6 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified and as directed. |
| 7 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc including ridges complete all as specified and as directed. |
| 8 | Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets as in roof coverings etc including ridges complete all as specified and as directed. |
| 9 | Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and as directed. |
| 10 | Dismantling of cast iron, wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule (BOQ), complete all as specified and as directed. |
| 11 | Taking down shutters (including fittings & fixtures) of any description exc 1 Sqm and not exc. 2 Sqm each, complete all as specified and as directed. |
| 12 | Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. |
| 13 | Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed. |
| 14 | Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 15 | Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed. |
| 16 | Removing excavated soil/material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed. |
| 17 | M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. |
| 18 | M&L for cement concrete (1:3:6) type C1 using 20mm graded crushed stone aggregate as in bed block or filling of chowkats, surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and as directed. |
| 19 | Extra over for forming fair finished drains or channels 30cm inner girth in cement concrete using extra cement including forms moulds, mitered/ stopped ends complete all as specified and as directed. |
| 20 | M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in copings, coving, roof padding, padding in sunken slab, including mixed with water proofing compound as per manufacture instructions complete all as specified & as directed. |
| 21 | M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in cills, steps, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, kerb stone, bed plates, roof kerbs, mud stops and the like including weathering, slightly rounded, chamfered angle and throating as directed including useand waste of form work (straightor curved) all exposed surface of concrete finished fair complete all as specified & as directed. |
| 22 | M&L for Precast reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for manholes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in cement mortar (1:6) complete all as specified & as directed.Note :- Reinforcement shall be measured and paid for separately under respective item of this Schedule. |
| 23 | M&L for reinforced cement concrete (Nominal Mix) (1:2:4) type B1 using 20mm graded crushed stone aggregate as in lintel, chajjas supported on wall and other similar work and the like complete all as specified & as directed.Note :- Reinforcement & formwork shall be measured and paid for separately. |
| 24 | Supply only liquid water proofing compound (ISI marked) complete all as specified & as directed. |
| 25 | M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 including demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 26 | M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 including demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 27 | Formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces of concrete complete all as specified & as directed. |
| 28 | Supply and fixing factory made 35mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles,fixed to chowkat, complete all as specified & as directed. |
| 29 | Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24(a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & as directed. |
| 30 | S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed. |
| 31 | S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube, fixing in opening as per specifications complete all as specified and as directed. |
| 32 | S&F factory made 30mm thick factory made solid PVC moulded door shutter with particle board core with 5mm thick PVC moulded sheet on the front face and 5 mm thick PVC plain coloursheet on back face complete all asspecifieddirected. |
| 33 | Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 34 | S&F 18mm thick Hybrid Water Proofing Board in cupboard shutter with decorative on one side & other side balancing white fixed by drilling screws complete all as specified and directed by Eng-in-charge. |
| 35 | S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed. |
| 36 | S&F Butt hinges of size 100mm stainless steel (ISI marked) complete all as specified and as directed. |
| 37 | S&F 150 mm long stainless steel barrel tower bolts (ISI marked) complete all as specified. |
| 38 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified. |
| 39 | S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified. |
| 40 | S&F 100mm long stainless steel handle (ISI marked) complete all as specified and as directed. |
| 41 | S&F 150mm long stainless steel handle (ISI marked) complete all as specified and as directed. |
| 42 | S&F 150mm size aluminium handle, cast type, powder coated, complete all as specified & as directed. |
| 43 | S&F in repair 300mm stainless steel sliding door bolts, bolt type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all asspd and directed. |
| 44 | S&F 300 mm long mild steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified & as directed. |
| 45 | S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 46 | Supply and fixing magnetic catcher fixed with nut, screw and washer complete all as specified & directed. |
| 47 | S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified. |
| 48 | Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 49 | S&F wooden finish powder coated mild steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including wooden finish decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C complete all as specified & as directed. |
| 50 | S&F mild steel framed work as in doors, gates, steel frames, chowkats, etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete all as specified and as directed. |
| 51 | S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, framed signed boards, walk ways, hold fast, railings, framework of water tanks and similar work including welding conforming to Grade E-165 (Fe 290), complete all as specified & as directed. |
| 52 | S&F rolled mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) Fe-290 Gde E-165 including distance pieces, cleats etc. complete all as specified & as directed. |
| 53 | S&F mild steel in tubular trusses including special shaped washer, framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed. |
| 54 | M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. |
| 55 | S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed. |
| 56 | S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed. |
| 57 | S&F Factory made box type steel window with hung shutter both glazed and gauged, shutter frame 60x25mm ERW hollow \"P\" section with wall thickness not less than 1mm fixed to pressed steel frame 120x70x1.6mm thick including fixing glazed portion, iron grills 8mm MS suare bar hunges with steel handle and fitting, lugs etc, including one coat of primer complete all as specified and directed.(Note : Wire mesh and glass shall be measured and paid separately under relevent items of Sch/BoQ). |
| 58 | S&F factory made steel windows conforming to IS-1038 with side hung shutters including projecting type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of red oxide zinc chromate primer complete all as specified and directed.Note : Wire cloth shall be measured and paid for separately. |
| 59 | S&F factory made steel windows conforming to IS-1038 with side hung shutters including projecting type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle, and steel peg stay, complete without glazing bars, dovetailed or welded including one shop coat of red oxide zinc chromate primer complete all as specified and directed.Note : Wire cloth shall be measured and paid for separately. |
| 60 | S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars complete welded including one shop coat of red oxide zinc chromate primer complete all as specified & as directed.Note : Glass shall be measured and paid for separately. |
| 61 | S&F for aluminium frame for doors, window/ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners including making arrangements to fix guard bars and S&F of PVC sleeves for guard bars. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge. |
| 62 | S&F glass dividing strips 3mm thick, 38mm wide and inserted in position, conform to design complete all as specified and as directed. |
| 63 | S&F Pre-painted galvalume aluminium zinc coating corrugated steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & as directed.Note : Colour of sheet shall be as approved by the GE. |
| 64 | S&F Pre-painted galvalume aluminum zinc coating Plain steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/ridge/fascia/cladding to wall, fixed with self tapping screws complete all as specified & as directed.Note : Colour of sheet shall be as approved by the GE. |
| 65 | M&L for false ceiling with 4mm thick E board classic fibre base cement boards embosed texture fixed with screws with & including anodised aluminium snap grid frame work of size 605mm x 605mm, including hangers 6mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed. |
| 66 | Supply and applying, Smart Care Damp Block 2K, two component elastomeric acrylic polymer modified cementitious water proofing coating, having 80% elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc, complete as per manufacturers specifications. Sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed. |
| 67 | Dismantling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed |
| 68 | Demolition of mud or bricks in roofs any thicknees and in any position and leaping over roof terrace removing the demolished material to a distance exc 250mnot exc 500m and depositing where directed at a lavel not exc 1.50m above starting point complete all as specified and as directed. |
| 69 | M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting of the following for RCC roof:-(a) Cleaning plastered roof surfaces and applying a coat of Oxidised bitumen based solvented primer @ 0.3 Kg/Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed.(b) M&L for APP modified polymeric waterproofing membrance 3mm thick with non woven polyster core of approved make applied by heating one surface of membrane with LPG tocrch with lap of 100mm and the overlap shall be seated by flame complete all as per manufacture instructions and as directed by EIC. |
| 70 | M&L for rendering 10mm thick in cement and sand mortar 1:4 on fair faces of brick work or concrete surfaces finished surface even & smooth without using exra cementmixed with liquid water proofing compound complete all as specified and as directed. |
| 71 | M&L for cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed, laid in floors over and including screed bed 15mm thick in cement and sand mortar 1:4 set and joint in neat cement slurry and pointed in cement and sand mortar 1:3 mixed with WPC of approved make in screed bed and pointed on roof complete all as specified and as directed. |
| 72 | M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified & as directed. |
| 73 | M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base complete all as specified and as directed. |
| 74 | M&L for 40mm thick PCC (1:2:4) type B1, using 20mm graded crushed stone aggregate as in floor and finished even and smooth using extra cement laid in alternate bay and joints filled with bituminous compound grade \"A\" complete all as specified and directed. |
| 75 | M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring, leveling course, etc, surface finished fair and even, complete all as specified and as directed. |
| 76 | M&L for machine cut Kota stone slab flooring 18 to 20mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed. |
| 77 | M&L for machine cut Kota stone slab 18 to 20mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed. |
| 78 | M&L for 16 to 18mm thick Granite (of any type) machine cut slab of approved shade (table rubbed and polished) with true & uniform joints as in steps, jambs, pillars, window cills, cooking platforms & like and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed (bedding layer) in CM 1:4 with cement slurry @ 3 Kg/Sqm complete all as specified & as directed.Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision. |
| 79 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. |
| 80 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. |
| 81 | M&L for Vitrified paving tiles of size 300x300x10mm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed. |
| 82 | M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed. |
| 83 | M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed. |
| 84 | M&L Pre polished Chequered tiles (any colour) 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment including 15mm screed bedding in cement and sand mortar (1:6)complete all as specified and directed. |
| 85 | M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 86 | M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed.Note : Shape of paver blocks shall be as approved by the GE. |
| 87 | M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finishedeven and smooth without using extra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid with an outward slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6mm wide and 10mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3). |
| 88 | M&L for Cutting for openings built in cement mortar, through brick walls for door, window and other openings or enlarging existing openings converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hardcore, etc. to store and rubbish not exc. 50m complete all as specified and as directed. |
| 89 | M&L for cutting cheses, pinning in, making good to facing where required & pointing in CM 1:3 for concrete water tubing and like not exc 10cm girth in brick wall etc complete all as specified and as directed. |
| 90 | M&L for guniting shortcrete 1:2 (CM) mixed with epoxy resin and hardner (manufactured by FOSROC/MC BAUCHEMIC /CICO/PIDILITE) @ 2% by weight of cement in equal proportion using shortcrete pumps and allied equipment, in thickness 30mm all as per manufactureres instruction. (Upto 5 metre height) including necessary chiping/taking down loose concrete along with application of rust remover for old rusted bars and rebar if required followed by application of anti corrosive paint over old /rebar as per manufacturers instruction completeall as specified and directed. |
| 91 | M&L for applying one coat of epoxy resin (FAIR BOND EP) on old concrete/brick surfaces @ 0.30 Kg/sqm including of surfaces as per manufacturer\"s instruction and applying 25mm thick (average thickness) of cement and sand (fine grit) in ratio 1:4 mixed with chloride free spray concrete plasticiser (spray crete) as per manufacturer\"s instruction with guniting machine of pressure capacity not lass than 5 Kg per Sqm and finished the surface even and smooth in cement and sand mortar 1:4 complete all as specified for buildings not more than triple storeyed complete all as specified and directed. |
| 92 | M&L for rendering 10mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified. |
| 93 | M&L for rendering 15mm thick in cement mortar 1:6 on brick masonry surfaces or on other than fair faces of brick masonry surfaces of walls, finished even & smooth without using extra cement complete all as specified. |
| 94 | M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry or on other than fair faces of brick masonry surfaces of walls, finished even & smooth without using extra cement complete all as specified. |
| 95 | M&L for rendering dubbing coat over damaged irregular surface of walls/chajjas/ roof projections/ ceiling/ facia etc average 15mm thick in cement and sand mortar 1:4 over cement slurry coat thick @ 3 Kg/sqm making the surface even followed by 5mm thick rendering in cement and sand mortar 1:3 furnished even & smooth including making of drip course and applying two coats of Apex/Cement Base Paint/White wash as required to match with existing surface complete including taking down/roughening surface of old surfaces by picking sweeping clean and washing with water complete all as specified. Note : Rate for formwork if required to be included in the rate quoted by the contractor. |
| 96 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and directed.Note : Supply only integral liquid water proofing compound shall be measured and paid for separately. |
| 97 | M&L for rendering 5mm thick in cement and sand mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified. |
| 98 | M&L for preparation of newly plastered / unplastered surfaces of walls & applying three coats of white wash complete all as specified and directed and directed. |
| 99 | M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified. |
| 100 | M&L for preparation of old surfaces (plastered or unplastered) of ceilings including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying two coats of white wash complete all as specified & as directed. |
| 101 | M&L for preparation of newly plastered surfaces of walls and applying two coats of distemper with distemper oil emulsion of approved shade/white or tinted over one coat of primer over & and including 1mm thick of wall care putty complete all as specified & directed. |
| 102 | M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, greasy spots etc and preparation of plastered surfaces and making smooth with sand paper and electric grinder and applying two coats of oil emulsion distemper (OBD) of approved shade & including 1mm thick white wall care putty on walls complete all as specified & as directed. |
| 103 | M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint complete all as specified & as directed. |
| 104 | M&L for complete removal of existing treatment of walls including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applyingtwo coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint on walls all as specified and as directed. |
| 105 | M&L for preparation of plastered/unplastered surfaces of walls and applying two coats of exterior emulsion or exterior weather coat paint (Apex) of approved shade/tint over a coat of primer complete all as specified & as directed. |
| 106 | M&L for complete removal of existing treatment from old plastered surfaces, preparation of surfaces of walls and applying two coats of weather proof acrylic emulsion paint (Apex) of approved shade/tint over a coat of primer height upto G+2 story Bldg complete all as specified & as directed. |
| 107 | S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed. |
| 108 | S&F 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified & as directed. |
| 109 | M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed. |
| 110 | M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamelpaint of approved tint over a coat of zinc chrome primer complete all as specified & as directed. |
| 111 | M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings as bends, elbows, tee, union, short pieces, connectors, check nuts, caps, plugs etc, laid in trenches, complete all as specified and as directed. |
| 112 | M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking down steel water tubing and connections of 15mm bore complete all as specified and as directed. |
| 113 | M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking down steel water tubing and connections of 20mm bore complete all as specified and as directed. |
| 114 | Supply and fixing in replacement of 700 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.Note : (i) The water storage tanks shall be 2 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water.(ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I.(iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item. |
| 115 | S&F 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed. |
| 116 | S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc, complete all as specified and as directed. |
| 117 | S&F in repair of CP Jet spray butterfly design fixed on EWC with stainless screws as approved complete all as specified and directed. |
| 118 | S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & as directed. |
| 119 | S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including32 mm dia PVC flush pipeconnected to water closet with inlet, ball valve, float and handle complete all as specified & as directed. |
| 120 | S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed. |
| 121 | S&F in repairs vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT spreader, PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia, complete all as specified and as directed. |
| 122 | S&F sink with drainage board made of stainless steel 1mm thick for Kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to brick wall, connecting union to pipe, overall minimum size 915mmx 460mm with bowl size 410mm x 330mm x 160mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings. |
| 123 | S&F in replacement of PVC connection 450mm long suitable for 15mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed. |
| 124 | S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete all as specified & as directed. |
| 125 | S&F in repairs 15mm bore wall mixer, with copper alloy, chromium plated hot and cold with or without telephonic shower, screwed down high pressure, screwed for iron pipes, complete all as specified & as directed. |
| 126 | S&F in replacement of 15mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed. |
| 127 | S&F in repairs 15 mm bore bib tap, 2 way, cast copper alloy, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed. |
| 128 | S&F 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed. |
| 129 | S&F in replacement of 15mm bore stop valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified & as directed. |
| 130 | S&F 15mm bore Angle stop valve, fancy type with long shank and cup of cast copper alloy chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified & as directed. |
| 131 | S&F in replacement of 20mm bore Gun metal gate valve conforming to IS : 778 (ISI marked) with iron wheel head, screwed both ends for iron pipe, including GI fitting socket, nipple, unions as well cutting of pipe and necessary earth work complete all as specified & directed. |
| 132 | S&F in repairs 600mm x 450mm looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood including aluminium framing and fixed to PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified. |
| 133 | S&F in repairs swivel shower of PTMT any colour for fixing with 15mm pipe (minimum weight 40gms) complete all as specified and as directed. |
| 134 | S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed. |
| 135 | S&F in repair toilet paper holder with flat recessed type stainless steel complete all as specified and as directed. |
| 136 | S&F in repairs soap dish holder brass chromium plated fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified & as directed. |
| 137 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with aluminium alloy brackets and guard rail 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as specified and as directed. |
| 138 | S&F in repairs glass shelf 450mm long x 100mm wide including railing & brackets fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified and directed. |
| 139 | S&F in repairs brass chromium plated Hand Shower (Health Faucet) with 8mm dia & 1.25m long stainless steel braided flexible tube and wall hook suitable for fixing to supply pipe of 15mm bore complete all as specified and as directed. |
| 140 | Supply and fixing in replacement of 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed, complete all as specified and as directed. |
| 141 | Supply and fixing in replacement of 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed, complete all as specified and as directed. |
| 142 | S&F 100mm bore cast iron bends (any radius) complete all as specified & as directed. |
| 143 | S&F 75mm bore cast iron bends (any radius) complete all as specified & as directed. |
| 144 | S&F in replacement of 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified & as directed. |
| 145 | S&F in replacement of 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified & as directed. |
| 146 | S&F in replacement of 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls fixed with including required clamps made out of flat iron 25x4mm complete all as specified & as directed. |
| 147 | S&F in replacement of 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls fixed with including required clamps made out of flat iron 25x4mm complete all as specified & as directed. |
| 148 | S&F 110mm bore PVC (SWR) bend any redius, joint with solvent cement complete all as specified & as directed. |
| 149 | S&F 75mm bore PVC (SWR) bend any redius, joint with solvent cement complete all as specified & as directed. |
| 150 | S&F 110mm bore PVC (SWR) Junction single, (Single ‘T’) equal or unequal with access door complete all as specified & as directed. |
| 151 | S&F 75mm bore PVC (SWR) Junction single, (Single ‘T’) equal or unequal with access door complete all as specified & as directed. |
| 152 | S&F 110mm bore PVC (SWR) Junction double, (double ‘T’) equal or unequal with access door complete all as specified & as directed. |
| 153 | S&F 75mm bore PVC (SWR) Junction double, (double ‘T’) equal or unequal with access door complete all as specified & as directed. |
| 154 | S&F PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement i complete all as specified & as directed. |
| 155 | S&F PVC (SWR) Gully trap 125/110mm bore setting and jointing with solvent cement complete all as specified & as directed. |
| 156 | S&F waste fittings 32mm bore, brass, chromium plate for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed. |
| 157 | S&F in repair Grating stainless steel 100mm bore size (with or without hole) fixed with white cement complete all as specified and as directed. |
| 158 | Dismantling loose/disintegrated portion of RCC Chajjas, bands,shelves, beams, coloumn or slab and similar work including support if required and stitching of cracks with MS U clamps of 8mm dia @ 150mm c/c with inserting concrate block strecthner with cement mortar 1:3 mixed with adhesive chemical (polymer based) and reinforced with PVC chicken mash including form work where where ever required and finished with 10mm thick plastering inCM 1:4 finished even & smooth without using extra cement incliding preparation of surfaces to receive finishes complete all as specified and directed. |
| 159 | S&F hard drawn steel wire fabric, weight not exc 4 Kg per sqm, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, supplied and fixed in reinforcement, complete all as specified & as directed. |
| 160 | M&L for construction of soakage wells excavation in ordinary soil, foundation in PCC 1:3:6, wells of honey combed and solid in M-25 concrete, including intercepting chamber, screen chamber brick work in cement and sand mortar, RCC cover slab in M-25/ RR masonry/ filling with brick bats, complete of size 3.0 m dia x 3.00 m deep complete all as specified and as directed. |
| 161 | Taking down carefully existing unserviceable/perished surface conduit/concealed conduit/ batten/ casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/conduit/casing caping, switches, sockets, ceiling rose, pendent holder, lamp holders, bracket holders, light fittings, top sheet covers, fan regulators, wooden boxes, MS sunken boxes, etc and making good the disturbed surfaces of wall, floors, ceiling, etc to match with the adjoining surfaces, complete all as specified and as directed. |
| 162 | M&L for Modular point wiring for one light/fan/bell/buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etcall as per IS, terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular switches, sockets, regulators etc with and including modular cover plates with frame of requisite module, complete all as specified and as directed.Notes : (i) Cost of cutting/leaving forming chases for conduits, sinking for modular metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed to include for modular metal flush boxes of requisite module and modular cover plates with frame of requisite module of colour as approved by GE. |
| 163 | All as per serial item No. 162.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches complete all as specified and directed. |
| 164 | All as per serial item No. 162.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board complete all as specified and directed. |
| 165 | All as per serial item No. 162.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed. |
| 166 | S&F Modular switch 1 way 6 Amp, 1 module, complete all as specified and as directed. |
| 167 | S&F Modular switch, 1 way 16 Amp, 1 module, complete all as specified and as directed. |
| 168 | S&F Modular Socket, 6 Amp - 2/3 pin combined 2 module, complete all as specified and as directed. |
| 169 | S&F Modular Socket 6 Amp/16 Amp - 2/3 pin combined 2 module, complete all as specified and as directed. |
| 170 | S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed. |
| 171 | S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit/casing caping fittings, ISI marked, complete all as specified and as directed. |
| 172 | S&F 9 Watt LED Bulb (Non-dimmable) of Standard / Universal size, Base - B22, Power Factor > 0.90, Lamp Efficiency > 80%,, Color Temperature - 3000 K, Lumen output - 900 lm, Colour Rendering Index (CRI) > 70, Warm white (WW) / Cool Day Light (CDL), 230 V, 50 Hz AC, ISI marked, complete all as specified and as directed. |
| 173 | S&F Modular Fan step regulator, 120 Watt - 2 module, complete all as specified and as directed. |
| 174 | S&F in replacement of LED (0.6 M)/ 2 ft smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 1150 lumen/10 watt at a minimum system efficacy of 1150 lumen per 10 watt and total power consumption not more than 10 watt including driver of 5 KA capacity. it has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 complete all as specified and directed. |
| 175 | S&F in replacement of LED (1.2 M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumen/20 watt at a minimum system efficacy of 2000 lumen per 20 watt and total power consumption not more than 20 watt including driver of capacity 10 KA. it has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 complete all as specified and directed. |
| 176 | S&F in replacement of bulk head energy efficient LED light fitting, 1x10 Watt, 230 Volts, surface mounted, comprising of high brightness LEDs, IP-65 protection, with & including all standard accessories, prewired and connecting up with & including 3 core sheathed flexible copper cable 1.5 sqmm of suitable length upto light point/ceiling rose, complete all as specified and as directed. |
| 177 | Supply and Fixing in replacement of Light Emitting Diode (LED) based street/ security light fitting, 35 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 3000 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA /polycarbonate /toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multi stranded copper conductor cable of 1100 Volt grade (ISI marked), fixed complete all as specified and as directed. |
| 178 | NOTES FOR LED LIGHT FITTINGS :(i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13.(ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80.(iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :-(a) Manufacturing defects.(b) Failure due to mechanical and electrical impact.(c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries. |
| 179 | Supply and fixing in replacement of mounting bracket (suitable for fixing/holding street/ security light fittings) made of 40mm bore GI pipe ‘light grade’ not less than 0.60m long, bent to shape at required angle, fixed to Pole/wall with & including mild steel clamps (02 Nos) made out of flat iron 50x6mm with nuts, bolts & washers, matching with section of Pole/suitable for wall, complete all as specified and as directed. |
| 180 | S&F in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 230 Volt, 10 kA, ‘C’ Curve, fixed complete all as specified and as directed. |
| 181 | S&F flush mounting factory made VTPN DB 4 way, 415 Volt, Double door, IP-43 protection, IK-09 with metal door with 250 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed.Note : Cost of cutting/leaving forming chases for sinking for DBand making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 182 | S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door type (IP-43 IK 09 with metal door), suitable for fixing MCBs, 240 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar, DB fitted with bus bar neutral links blank plates, SPN, 8 way, suitable for MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed.Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 183 | S&F in replacement of MCB, 6 to 32 Amps, Single Pole (SP), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve,with over load and short circuit protection, complete all as specified and as directed. |
| 184 | S&F in replacement of MCB, 6 to 32 Amps, Single Pole Neutral (SPN), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve,with over load and short circuit protection, complete all as specified and as directed. |
| 185 | S&F in replacement of MCB, 40 Amps, Single Pole Neutral (SPN), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve,with over load and short circuit protection, complete all as specified and as directed. |
| 186 | S&F MCCB 3 Pole 160 Amps, Adjustable thermal having, breaking capacity 16 KA, 415 Volt & making connections with 25x3 mm copper strip as required, including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed. |
| 187 | Supply, assembling, hanging, fixing & testing Ceiling Fan of size 1200 mm sweep, minimum air delivery 210 CMM with service value 6.00 BEE, 5 star rated, with brushless direct current (BLDC) motor, single phase, AC supply, 230 Volt, with & including down rod, canopies, three number blades, capacitor 2.5 mfd, hook, rubber reel, safety pins, nuts, bolts, washers, cable connector and making connection with PVC insulated & sheathed 1 Sqmm three core flexible copper multistranded conductor cable (ISI marked) from ceiling rose to connector of ceiling fan including marking of SM / MES number with thick synthetic enamel paint of approved tint complete all as specified and as directed.Note :- The font, style & place of writing SM/ MES number with synthetic enamel paint on ceiling fan shall be as directed by the Engineer-in-Charge and cost thereof shall deemed to be included in quoted rates. |
| 188 | Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50 Cycle per second, size 300mm sweep with blades and frame including self closing GI louvers off mode protection against birds etc mounted in suitable opening arrangement. including electric connection with and including new 1 Sqmm, 2 core flexible copper conductor cable from ceiling rose to fan, (not exceeding 0.5 mtr long), and hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and AGE(I) Office name shall also be written on fan with red colour permanent marker. |
| 189 | M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre,charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers,PCCchamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc including dismantling & taking out old existing unserviceable earthing complete all as specified & as directed.Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. |
| 190 | M&L for Earthing to equipments with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 25x4 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/ welded to earth plate at one end and other end of strip connected to equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50mincluding dismantling & taking out old existing unserviceable earthing complete all as specified and as directed.Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. |
| 191 | M&L for sub main wiring with two runs of 4 sqmm (nominal area) size main cable & one run of 4 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI markedcables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed.Notes :-(i) 02 runs of 4 sqmm size main cable, 01 run of 4 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 192 | M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI markedcables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed.Notes :-(i) 02 runs of 6 sqmm size main cable, 01 run of 6 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item. |
| 193 | Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 35 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out old unserviceable cable complete all as specified and directed.Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. |
| 194 | Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out old unserviceable cable complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. |
| 195 | Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc including dismantling & taking out old unserviceable cable complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. |
| 196 | M&L for sand cushioning using clean local unwashed sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of underground electric cable complete all as specified and as directed.Notes : (i) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used.(ii) For the purpose of payment, only punned thickness shall be measured. |
| 197 | M&L for sub class ‘B’ (old size) burnt clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed. |
| 198 | M&L for Boring of holes under road, pavement, hard standing, (minimum 1.0m below) etc by using necessary machine / manually without disturbing the top surface suitable for passing the GI protection pipe / cables, complete all as specified and as directed. |
| 199 | M&L for Galvanized iron tubing, 50mm bore light grade, ISImarked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete all as specified and directed.Note :- Excavation & earthwork shall be measured & paid for separately. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
