|
| 1 | SOFA SET5 SEATED |
| 2 | Removing the existing unserviceable tapastry cloth, cushion of sofa set 5 seater and replacing with new tapastry cloth including mulmul with foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm. The tapastrycloth shall be mat finish and shall not less than Rs. 800/- per metre and as approved by GE. , rest all as shown on drg and as directed by Engr-in-Charge. |
| 3 | Removing the existing unserviceable front leg from Sofa and providing new first class teak wood ofleg size 70mm x 35 mm x 300mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 4 | Removing the existing unserviceable rear leg from Sofa and providing newfirst class teak wood leg size 70mm x 35 mm x 260mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 5 | Removing existing unserviceable Arm restfrom Sofa and providing newfirst class teak wood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 6 | Removing existing unserviceable side railfrom Sofa and providing newfirst class teak wood side rail of size 35 mm x 100mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 7 | Removing existing unserviceable bearerfrom Sofaand providing newfirst class teak wood bearer of size 40mm x 40mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 8 | Removing existing unserviceable battensfrom Sofa and providingnewfirst class teak woodbattens of size 50mm x 20 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 9 | Removing existing unserviceable front railfrom Sofa three seater and providingnewfirst class teak wood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 10 | Removing existing unserviceable front rail from Sofa single seaterand providingnewfirst class teak woodfront rail of size 35mm x 10mm x 530 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 11 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polishover a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 12 | SOFA SET4 SEATED |
| 13 | Removing the existing unserviceable tapastry cloth, cushion of sofa set 4 seater and replacing with new tapastry cloth including mulmul with foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm. The tapastrycloth shall be mat finish and shall not less than Rs. 350/- per metre and as approved by GE. , rest all as shown on drg and as directed by Engr-in-Charge. |
| 14 | Removing the existing unserviceable front leg from Sofa and providing new first class teak wood ofleg size 70mm x 35 mm x 300mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 15 | Removing the existing unserviceable rear leg from Sofa and providing newfirst class teak wood leg size 70mm x 35 mm x 260mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 16 | Removing existing unserviceable Arm restfrom Sofa and providing newfirst class teak wood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 17 | Removing existing unserviceable side railfrom Sofa and providing newfirst class teak wood side rail of size 35 mm x 100mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 18 | Removing existing unserviceable bearerfrom Sofaand providing newfirst class teak wood bearer of size 40mm x 40mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 19 | Removing existing unserviceable battensfrom Sofa and providingnewfirst class teak woodbattens of size 50mm x 20 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 20 | Removing existing unserviceable front railfrom Sofa three seater and providingnewfirst class teak wood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 21 | Removing existing unserviceable front rail from Sofa single seaterand providingnewfirst class teak woodfront rail of size 35mm x 10mm x 530 mm, rest all as shown on drg and as directed by Engr-in-Charge. |
| 22 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polishover a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 23 | CHAIR EASY Cushioned |
| 24 | Removing the existing unserviceable tapastry cloth, cushion of easy chair and replacing with new tapastry cloth including mulmul with foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm. The tapastrycloth shall be mat finish and shall not less than Rs. 800/- per metre and as approved by GE. , rest all as shown on drg and as directed by Engr-in-Charge. |
| 25 | Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 55x25 x300mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 26 | Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 50x25x355mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 27 | Removing the existing unserviceable broken arm rest and providing new Padauk wood arm rest of size 65x25x610mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 28 | Removing the existing unserviceable back member and providing new Padauk woodback member of size 75x25x380 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 29 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish tillglossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 30 | Chair computer Revolving |
| 31 | S & F in repairs ofmaintenance free Gas lift for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 32 | S & F in repairs ofPadestal assy. Injection moulded in black 30% glass filled nylon , 50mm MS castor pin isof press fitted to each prong for holding the castor,for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 33 | S & F in repairs of twin wheel castorsfor all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 34 | S & F in repairs of PU seat duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 35 | S & F in repairs of PU back duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 36 | S & F in repairs removing of old upholstry from seat and back of all type of chairs with new best quality Acrylic/polyester febric complete including uphostry work for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 37 | S & F in repairs of nut & bolts of chair revolving made of Malleable Steel complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 38 | S & F in repairs of handles of chair revolving made of blackintegeral skin polyurethane reinforced with MS insert scratch proof complete for all type of chairs revolvingwith arm rest all as shown on drg and as directed by Engr-in-Charge. |
| 39 | Chair Executive Revolving |
| 40 | S & F in repairs ofmaintenance free Gas lift for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 41 | S & F in repairs ofPadestal assy. Injection moulded in black 30% glass filled nylon , 50mm MS castor pin isof press fitted to each prong for holding the castor,for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 42 | S & F in repairs of twin wheel castorsfor all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 43 | S & F in repairs of PU seat duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 44 | S & F in repairs of PUback duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 45 | S & F in repairs removing of old upholstry from seat and back of all type of chairs with new best quality Acrylic/polyester febric complete including uphostry work for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 46 | S & F in repairs of nut & bolts of chair revolving made of Malleable Steel complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 47 | S & F in repairs of handles of chair revolving made of blackintegeral skin polyurethane reinforced with MS insert scratch proof complete for all type of chairs revolvingwith arm rest all as shown on drg and as directed by Engr-in-Charge. |
| 48 | Chair Visitor/Chair writing MAP |
| 49 | S & F in repairs of PUseat duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 50 | S & F in repairs of PU back duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 51 | S & F in repairs of handles of chair visitor made of blackintegeral skin polyurethane reinforced with MS insert scratch proof complete for all type of chairs revolvingwith arm rest all as shown on drg and as directed by Engr-in-Charge. |
| 52 | S & F in repairs of nut & bolts of chair revolving made of blackintegeral skin polyurethane reinforced with MS insert scratch proof complete for all type of chairs revolvingwith arm rest all as shown on drg and as directed by Engr-in-Charge. |
| 53 | Chair Cushioned with arms/chair moulded cushioned |
| 54 | S & F in repairs of PU seat duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 55 | S & F in repairs of PU back duly upholstered with best quality Acrylic/polyester fabric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 56 | Chair Cushioned without arms |
| 57 | S & F in repairs of PUseat duly upholstered with best quality Acrylic/polyester febric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 58 | S & F in repairs of PU back duly upholstered with best quality Acrylic/polyester febric complete for all type of chairs revolving rest all as shown on drg and as directed by Engr-in-Charge. |
| 59 | BED HARD (TP) |
| 60 | S&F 12mm thick plywood BWP Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitablescrews wood/steel including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge. |
| 61 | S&F in repairs to 1st qualityPaduak wood long rail 35mm x 90mmx 1980mm in section as per existing size of Bedincluding removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge |
| 62 | All as per item No. 1.02,but short rail of size 35mm x 90mmx 610mm all as specified on drawing or as directed by Engineer-in-charge. |
| 63 | S&F in reapirs to head board consisting of 60 x 30 x 260mm vertical size and 30 x 60 x 400mm horizontal including legs of size 60 x 60mm in section at top and length 400mm from bottom of leg and 30 x 30mm in section at bottom complete including removal of damaged head board all as specified on drawing or as directed by Engineer-in-charge. |
| 64 | All as per item No. 1.04, but foot board consisting of 22 x 75mmx 900mm in section paduak wooden battens 3 Nos at equal space, joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30 x 60 x180mm shall be 1st quality of Padauk wood. The vertical legs above horizontal rails shall be 30 x 60x180mm all as specified on drawing or as directed by Engineer-in-charge. |
| 65 | S&F in reapirs to new 1st quality Paduak wood stiffeners of size 40 x 60 x 900mm complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge. |
| 66 | S&F in reapirs to 4mm thick one side teak finished plywoodof size 780 x 340mm including 12mm dia half cut teak wood beading of both side of head board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge. |
| 67 | S&F in reapirs to 4mm thick one side teak finished plywood of size 780 x 180mm including 12mm dia half cut teak wood beading of both side of foot board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge. |
| 68 | S&F in repairs to flat iron of mild steel of size 35 x35 x 5mm, bents to right angle on each corners of Bed Hard all as specified on drawing or as directed by Engineer-in-charge. |
| 69 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish till the glossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 70 | CHARPOY MS WITH PLYWOOD TOP |
| 71 | S&F in repairs to 1980mm long, 900mm wide,12mm thick plywood BWP Grade,single piece ofapproved quality with suitable steel screw and cup washer including removal of damaged plywood, rest all as shown on drg and as directed by Engr-in-Charge. |
| 72 | Hard Rubber/PVC Shoe of superior quality (Set of four, each set will be measured as one) as approved & as directed by Engr-in-charge. |
| 73 | Removal of existing worn out paint and Re-Painting to the entire frame of Charpoy MS P/Top with Black colour synthetic enamel paint over a coat of primer of approved make rest all specified on drawing or as directed by Engineer-in-charge. |
| 74 | Table Office Officers wooden |
| 75 | S&F in repairs drawers made of 18 mm thick prelaminated MDF Board OST duly finished with standard workmanship for Table Office Officers wooden complete same as per existing drawer, rest all as shown on drg and as directed by Engr-in-Charge. |
| 76 | S&F in repairs top of Table office officer top with 18mm thick prelaminatedMDF board one side teak facing and balancing white on other side all the four edges provided with suitable PVC beading, rest all as shown on drg and as directed by Engr-in-Charge. |
| 77 | S & F MS Lock (6 liver brass levers) with duplicate keys for drawers/cup-board, rest all as shown on drg and as directed by Engr-in-Charge. |
| 78 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish tillglossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 79 | Chair School with Hand Board |
| 80 | Replacement of existing unserviceable PVC seat with new PVC seat of approved Make rest all as shown on drg and as directed by Engr-in-Charge. |
| 81 | S&F hand board made out of 18 mm thik prelaminated MDF Board OST with PVC beading 1 mm thick alaround complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 82 | Removal of existing worn out paint and Re-Painting to the entire frame of Chair School w/hand Board with Black colour synthetic enamel paint over a coat of primer of approved make rest all specified on drawing or as directed by Engineer-in-charge. |
| 83 | S&F Hard PVC/rubber shoes of superior quality (Set of four, each set will be measured as one) as specified and as directed by Engr-in-charge. |
| 84 | CHAIR DINING CUSHION |
| 85 | Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 86 | Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 30x55x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 87 | Removing the existing unserviceable back rest and proving new Padauk wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge. |
| 88 | Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 30x65x420mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 89 | Removing the existing unserviceable rear rail of size and proving new Padauk wood rear rail 30x65x460mmcomplete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 90 | Removing the existing unserviceable side rails and providing new Padauk wood side rails of size 30x65 x430mm complete all as specified on drawing or as directed by Engineer-in-charge. |
| 91 | Removing the existing unserviceable fabricleatherite seat and cushion providing new fabric seat and cushion 460mmx75 mm thick 40 mm density foam cover with fabric seat and 12 mm BWP ply wood, the cost of fabric should not be less than Rs 800 per meter sall as specified on drawing or as directed by Engineer-in-charge |
| 92 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polishover a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 93 | S&F Hard PVC/rubber shoes of superior quality duly fixed using screw of suitable size (Set of four, each set will be measured as one) as specified and as directed by Engr-in-charge. |
| 94 | CHAIR DINING PVC Seat |
| 95 | Removing the existing unserviceable rear leg and providing with new Padauk wood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 96 | Removing the existing unserviceable front leg and providing with new Padauk wood front leg of size 30x55x460mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 97 | Removing the existing unserviceable back rest and proving new Padauk wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 98 | Removing the existing unserviceable front rail and providing new Padauk wood front rail of size 30x65mm complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 99 | Removing the existing unserviceable rear rail of size and proving new Padauk wood rear rail complete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 100 | Removing the existing unserviceable side rails and providing new Padauk wood side rails of size 30x65 mmcomplete all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 101 | Removing the existing unserviceable PVC seat and providing new PVC seat of approved make complete rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 102 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polishover a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. for the following furniture articles:- |
| 103 | S&F Hard PVC/rubber shoes of superior quality duly fixed using screw of suitable size (Set of four, each set will be measured as one) as specified and as directed by Engr-in-charge. |
| 104 | COMMON FOR ALL CHAIRS (FD/MAP-II/04, FD/E6/MAP/10®,FD/MAP-II/05 |
| 105 | Removing the existing unserviceable stiffeners and providing new Padauk wood 2nd class hard wood stiffeners of thickness 25x20 mm . |
| 106 | BED HARD Steel with P/Top |
| 107 | S&F 12mm thick plywood BWP Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitablescrews wood/steel including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge. |
| 108 | S&F in repairs to head boards made out of Prelaminated MDF Board OST having 1 mm thick PVC beading all around as per existing size of Bedincluding removal of damaged board rest all as specified on drawing or as directed by Engineer-in-charge |
| 109 | S&F in repairs to foot boards made out of Prelaminated MDF Board OST having 1 mm thick PVC beading all around as per existing size of Bedincluding removal of damaged board rest all as specified on drawing or as directed by Engineer-in-charge |
| 110 | Hard Rubber/PVC Shoe of superior quality (Set of four, each set will be measured as one) as approved & as directed by Engr-in-charge. |
| 111 | Removal of existing worn out paint and Re-Painting to the entire frame of Charpoy MS P/Top with Black colour synthetic enamel paint over a coat of primer of approved make rest all specified on drawing or as directed by Engineer-in-charge. |
| 112 | Table Bed side MAP |
| 113 | M&L for removing paint by scraping down old paint carrying out repair such as removing the dents and welding wherever requiredand applying two coats of synthetic enamelled paint black colour over a coat of primer after preparation of surfaced,completeall as shown on drg and as directed by Engineer-in-charge. |
| 114 | Removing of existing unserviceable side of Table Bed Side and providingnew sides of 18mm thick prelaminated MDF Board with OST and balancing white on the other side of exterior grade, rest all as specified on drawing or as directed by Engineer-in-charge. |
| 115 | Replacement of existing unserviceable table top for Table bed side steel MAP made out of 18mm thick prelaminated particle board exterior grade with suitable PVC edging al-round top of table, completeall as shown on drg and as directed by Engineer-in-charge. |
| 116 | Removing the existing unserviceable Top drawer and providing New drawer made out of 18 mm thick MDF boardon both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 117 | Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 18 mm thick MDF boardon both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : Each drawer will be measured as single unit) |
| 118 | Removing of existing unserviceable side of Table Bed Side and providingnew sides of 18mm thick prelaminated MDF Board with OST and balancing white on the other side of exterior grade, rest all as specified on drawing or as directed by Engineer-in-charge. |
| 119 | Removing of existing unserviceable Back of Table Bed Side and providingnew Back of 6mm plywood BWP Grade shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge. |
| 120 | S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one |
| 121 | Rack Shoe Steel |
| 122 | M&L for removing paint by scraping down old paint carrying out repair such as removing the dents and welding wherever requiredand applying two coats of synthetic enamelled paint black colour over a coat of primer after preparation of surfaced,completeall as shown on drg and as directed by Engineer-in-charge. |
| 123 | S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one |
| 124 | BIN LINEN MULTIPURPOSE with ironing board |
| 125 | Removing the existing unserviceable top of Bin linen Multipurpose and providing new top made out of 18mm thick prelaminated MDF board exterior grade of size 1220 x 455 mm all as specified on drawing or as directed by Engineer-in-charge. |
| 126 | Removing the existing unserviceable back of Side Board and providing new Back with 6mm thick plywood BWP type of Size 650 x 1220 mm all as specified on drawing or as directed by Engineer-in-charge. |
| 127 | Removing the existing unserviceabledrawer and providing New drawer made out of 18 mm thick MDF boardon both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing or as directed by Engineer-in-charge. |
| 128 | Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated MDF boardincluding Hinges rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit) |
| 129 | Removing the existing unserviceable leg frame of side board and providing Padauk wood 2nd class hard wood leg frame all as specified on drawing or as directed by Engineer-in-charge. |
| 130 | Removing the existing unserviceable broken legs of side board and providing new Padauk wood leg 2nd class hard wood of size 45 x 45 x 125 mm but at bottom 25 x 25 mm all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. directed by Engineer-in-charge.(Note : Each leg will be measured as single unit.) |
| 131 | Replacement of existing damaged hinges with 75mm long piano type hinges of shutters. |
| 132 | Replacement of existing damaged handles with chromium plated handles of suitable, size rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 133 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying french polish tillglossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 134 | Table Computer |
| 135 | Removing the existing unserviceable top of Table Computer and providing new top made out of 18mm thick prelaminated MDF board exterior grade OST face and other side balancing white all as specified on drawing or as directed by Engineer-in-charge. |
| 136 | Removing the existing unserviceabledrawer and providing New drawer made out of 18 mm thick MDF boardcomplete, all as specified on drawing or as directed by Engineer-in-charge. |
| 137 | Replacement of existing damaged handles with chromium plated handles of suitable, size rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 138 | S & F MS Lock (6 liver brass levers) with duplicate keys for drawers, rest all as shown on drg and as directed by Engr-in-Charge. |
| 139 | Removing the existing unserviceable keyboard tray and providing New keyboard tray made out of 18 mm thick MDF boardcomplete, all as specified on drawing or as directed by Engineer-in-charge. |
| 140 | Locker for 12 Pers w/lock |
| 141 | S & F MS Lock (6 liver brass levers) with duplicate keys for drawers of Lockers, rest all as shown on drg and as directed by Engr-in-Charge. |
| 142 | (g) Removal of existing worn out paint and Re-Painting to the entire frame of locker with white colour synthetic enamel paint over a coat of primer of approve completeall as shown on drg and as directed by Engineer-in-charge. |
| 143 | Teapoy Verandah MAP |
| 144 | M & L forwelding of broken jointsof Teapoy varandah including preparation of surface and applying two coat of black synthetic enamel paint over a coat of red oxide primer complete, completeall as shown on drg and as directed by Engineer-in-charge. |
| 145 | Replacement of existing unserviceable table top for Teapoy verandah MAPmade out of 18mm thick pre laminated MDF board teak finish on top and balancing white with on the other and all the four edges provided with suitable PVC beading completeall as shown on drg and as directed by Engineer-in-charge. |
| 146 | Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with black colour synthetic enamel paint over a coat of primer of approve make completeall as shown on drg and as directed by Engineer-in-charge. |
| 147 | Almirah large 1/2hx1/2s steel with Side Mirror |
| 148 | S&F in repairs legs ofAlmirah Large 1/2hx1/2s steel with side mirror and providing newlegs by welding made out of 1mm MS Sheetinto required shape , complete all as shown on drg and as directed by Engineer-in-charge. |
| 149 | S&F in repairs shelveswith MS sheet CRC 1mm thick bent to shapeincluding welding to the almirahs,completeall as shown on drg and as directed by Engineer-in-charge. |
| 150 | S & F in repairs locking device including replacement of brass 6 lever locks brass with duplicate keys chromium plated, complete all as shown on drg and as directed by Engineer-in-charge. |
| 151 | S&F in repairs handle Chromium plated of size 150 mm grip length with both sides screwed , completeall as shown on drg and as directed by Engineer-in-charge. |
| 152 | S&F in repairs doorwith MS sheet CRC 1mm thick bent to shape as specified including replacement of hinges all as shown on drawing and as directed by Engineer-in-charge. |
| 153 | S&F in repairs Almirah glazed steel by removing of existing unserviceable mirrorneatly and replacing the new mirrorplain 5 mm thick with suitable bolts and clamps to be fitted , complete all as shown on drg and as directed by Engineer-in-charge. |
| 154 | Repair to existing shelf including welding all as directed by Engineer-in-charge. |
| 155 | Removal of existing worn out painting from in side & outside including preparation of surface frame completeand M&L for applying two coats of 1st quality synthetic enamel paint of approved colour and makecomplete all as shown on drg and as directed by Engineer-in-charge. |
| 156 | Almirah med 1/2hx1/2s steel with Side Mirror |
| 157 | S&F in repairs legs ofAlmirah med 1/2hx1/2s steel with side mirror and providing newlegs by welding made out of 1mm MS Sheetinto required shape , complete all as shown on drg and as directed by Engineer-in-charge. |
| 158 | S&F in repairs shelveswith MS sheet CRC 1mm thick bent to shapeincluding welding to the almirahs,completeall as shown on drg and as directed by Engineer-in-charge. |
| 159 | S & F in repairs locking device including replacement of brass 6 lever locks brass with duplicate keys chromium plated, complete all as shown on drg and as directed by Engineer-in-charge. |
| 160 | S&F in repairs handle Chromium plated of size 150 mm grip length with both sides screwed , completeall as shown on drg and as directed by Engineer-in-charge. |
| 161 | S&F in repairs doorwith MS sheet CRC 1mm thick bent to shape as specified including replacement of hinges all as shown on drawing and as directed by Engineer-in-charge. |
| 162 | S&F in repairs Almirah glazed steel by removing of existing unserviceable mirrorneatly and replacing the new mirrorplain 5 mm thick with suitable bolts and clamps to be fitted , complete all as shown on drg and as directed by Engineer-in-charge. |
| 163 | Repair to existing shelf including welding all as directed by Engineer-in-charge. |
| 164 | Removal of existing worn out painting from in side & outside including preparation of surface frame completeand M&L for applying two coats of 1st quality synthetic enamel paint of approved colour and makecomplete all as shown on drg and as directed by Engineer-in-charge. |
| 165 | Cabinet file steel |
| 166 | S & F in repairs locking device including replacement of brass 6 lever locks brass with duplicate keys chromium plated, complete all as shown on drg and as directed by Engineer-in-charge. |
| 167 | Repair to existing shelf including welding all as directed by Engineer-in-charge. |
| 168 | Removal of existing worn out painting from in side & outside including preparation of surface frame completeand M&L for applying two coats of 1st quality synthetic enamel paint of approved colour and makecomplete all as shown on drg and as directed by Engineer-in-charge. |
| 169 | Chair Verandah officer |
| 170 | Repair/replacement of broken Leg, each one piece made of MS conduit pipe 16G, 19/20mm dia including welding andproviding one coat of red oxide primer all as per drg and as directed by Engineer-in-charge. |
| 171 | Welding joints of broken leg of 19/20mm MS tube & other jointsas per drg complete all as shown on drg and as directed by Engineer-in-charge. |
| 172 | Hard PVC/Nylon shoes as per drg complete all as shown on drg and as directed by Engineer-in-charge. |
| 173 | S & F in repairs PVC Seat and Back with approved make complete all as shown on drg and as directed by Engineer-in-charge. |
| 174 | Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with white colour synthetic enamel paint over a coat of primer of approve make all specified on drawing or as directed by Engineer-in-charge. |
| 175 | Table Centre w/glass top |
| 176 | S & F in repairs Glass top 8 mm thickblack color for Table Centre glass top complete all as specified on drawing or as directed by Engineer-in-charge. |
| 177 | S&F in repairs to unserviceable damaged legs from Table Centreglass top made out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 178 | S&F in repairs to unserviceable damaged front long rails made out of hard wood (Padauk)complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 179 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish tillglossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 180 | S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one |
| 181 | Teapoy w/glass top |
| 182 | S & F in repairs Glass top 8 mm thick black color for Teapoy with glass top complete all as specified on drawing or as directed by Engineer-in-charge. |
| 183 | S&F in repairs to unserviceable damaged legs from teapoy with glass topmade out of hard wood (Padauk) complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 184 | S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from teapoy made out of hard wood (Padauk)complete, rest all as shown on drg and as directed by Engr-in-Charge. |
| 185 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying melamyne polish tillglossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 186 | S&F PVC buffer shoes to legs of various chairs using screw of suitable size, as per sample (Set of four shoes) each set will me measured as one |
| 187 | Shoe rack 2 door |
| 188 | Removing the existing unserviceable top of shoe rack 2 door and providing new top made out of 18mm thick prelaminated MDF board exterior grade all as specified on drawing or as directed by Engineer-in-charge. |
| 189 | Removing the existing unserviceable back and providing new Back with 6mm thick plywood BWP type of Size 650 x 1220 mm all as specified on drawing or as directed by Engineer-in-charge. |
| 190 | Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated MDF board including Hinges rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit) |
| 191 | Replacement of existing damaged handles with chromium plated handles of suitable, size rest all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 192 | M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying french polish tillglossy finishing complete all as specified on drawing or as directed by Engineer-in-charge. |
| 193 | Wood Vineer Coffee Cabinet |
| 194 | Removing the existing unserviceable top of wood vineer coffee cabinet and providing new top made out of 18mm thick prelaminated MDF board exterior grade of size 1220 x 455 mm all as specified on drawingor as directed by Engineer-in-charge. |
| 195 | Removing he existing unserviceable back of Side Board and providing new Back with 6mm thick plywood BWP type of Size 650 x 1220 mm all as specified on drawing or as directed by Engineer-in-charge. |
| 196 | Removing the existing unserviceable Top drawer and providing New drawer made out of 18 mm thick prelaminated MDF boardon both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge. |
| 197 | Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 18 mm thick prelaminated MDF boardon both sides and 6 mm thick BWP ply on bottom and back side, all as specified on drawing or as directed by Engineer-in-charge. (Note : Each drawer will be measured as single unit) |
| 198 | Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated MDF boardincluding Hinges duly fittedtransparent glass 4 mm thick rest all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit) |
| 199 | Replacement of existing damaged handles with chromium plated handles of suitable, size rest all as specified on drawingor as directed by Engineer-in-charge. |
