|
| 1 | Almirah steel large (a) Taking out of broken door shutter from Almirah Large Steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting. All as directed by Engineer-in-Charge and shown on drawing |
| 2 | (b) Removing the worn out u/s handle from the almirah and providing/fixing of new handle chromium plated heavy duty as approved by Engr-in-charge/GE. |
| 3 | (c) Removing the worn out u/s lock from almirah and providing /fixing with new lock 6 lever with dublicate key ISI marked with round shape of MS key plate as approved by Engr-in-charge/GE duly fixed as per drawing. |
| 4 | (d) Removing the worn out u/s 3 way locking device and providing/fixing the new one in its original position as per drg. |
| 5 | (e ) Removing the worn out u/s leg and providing/ fixing the new leg madeout of Mssheet 1.00 mm thick in its original position duly welded as per drg |
| 6 | (f) Taking out iof u/s wornout shelf and providing the new one of existing size and shape madeout of MS sheet 1.00 mm thick all as shown on drg |
| 7 | (g) Removing the worn out paint from internal/ external surface of almirah steel large by scraping, necessary preparation of surface for painting duly dented/painted and smoothen the surface by putty and painting the the internal and external surface with two coat of synthetic enamelled paint over a coat of primer metal to bring the swurface to a glossy shine as directed by Engr-in- charge |
| 8 | Almirah Steel Medium (a) All as per item no. 1.01 here in before but for almirah steel medium |
| 9 | (b)All as per item no. 1.02 here in before but for almirah steel medium |
| 10 | ( c)All as per item no. 1.03 here in before but for almirah steel medium |
| 11 | (d)All as per item no. 1.04 here in before but for almirah steel medium |
| 12 | ( e)All as per item no. 1.05 here in before but for almirah steel medium |
| 13 | (f)All as per item no. 1.06 here in before but for almirah steel medium |
| 14 | (g)All as per item no. 1.07 here in before but for almirah steel medium |
| 15 | (h) Hasp & Staple of locker med steel |
| 16 | Repair /re-canning of chair easy Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well sesoned (Teak) and fixing the same in its original position as per drawing(a) Front legs |
| 17 | (b) Front rail of seat frame (Hole should be 12.5 mm apart of each other |
| 18 | (c ) Side rail (Ditto complete) |
| 19 | (d) Back rail (Ditto complete) |
| 20 | (e ) Arm rest |
| 21 | (f) Remove the existing u/s canning and supply and weave with 2mm thick new white plastic cane oval shape Godrej pattern and beading with 4 mm thick new white plastic can make Ajay /Premier as approval by GE and providing the new hard rubber shoes on legs below of chair easy. |
| 22 | (g) Preparation of surface by remove of existing polishing mark scratchs from all exposed wooden surfaces to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by engineer-in-Charge. |
| 23 | Chair CB steel With Arm(a) Removing the worn out paint by scrapping from the steel surface , necessary preparation of surface for painting and welding wherever required , two coat of spray painting with synthetic enamel paint olive green over a coat of metal premier after dent bent portion. Wooden surface would be black polish to required glazed andshine. |
| 24 | (b) Removing the worn out u/s seat frame and providing / fixing the new one of existing size made out of 1st class teak wood duly recanning with new plastic paint 2mm thick oval shape for general weaving and 4mm thick plastic cane for breading all around as shown in drawing. Wooden frame should be finish with black polish and fix in its original position with required screw (plastic cane type-I HDPE). |
| 25 | (c ) All as per item 4.02 here-in before but back frame. |
| 26 | (d) Removing the worn out u/s handle made out of H.W(T.W) well sesoned and providing/fixing of existing size and shape with required screw after finish with black polish. |
| 27 | Chair CB steel Without Arm (a) All as per item no. 4.01 here-in-before but for chair CB steel without arm. |
| 28 | (b) All as per item no. 4.02 here-in-before but for chair CB steel without arm. |
| 29 | (c) All as per item no. 4.03 here-in-before but for chair CB steel without arm. |
| 30 | Repair of chair Dinning(a) Remove the existing unserviceable/broken 12mm ply seat from chair dinning and supply & fixing the new 12mm ply seat 4mm existing size in its original position, all as directed by Engr-in-Charge and shown on drg. |
| 31 | (b) Remove of existing unserviceable under mentioned members nad providing the new one made out of 1st class HW well seasoned (Teak Wood) and fixing the same in its, original position all as directed by Engr-in-Charge and shown on drg.. |
| 32 | (i) Front leg, all as directed by Engr-in-Charge and shown on drg. |
| 33 | (ii) Rear leg, all as directed by Engr-in-Charge and shown on drg. |
| 34 | (iii) Front rail of seat frame, all as directed by Engr-in-Charge and shown on drg. |
| 35 | (iv)Side Rail, all as directed by Engr-in-Charge and shown on drg. |
| 36 | (v) Back rail, all as directed by Engr-in-Charge and shown on drg. |
| 37 | (vi) Short stiffener (390x390mm), all as directed by Engr-in-Charge and shown on drg. |
| 38 | (vii) 75 mm thick, 32 density cushion (Kurlon) |
| 39 | (Viii) Back Rest Batten |
| 40 | Locker Steel (a)Taking out of broken door shutter from Locker steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting, all as directed by Engr-in-Charge and shown on drg. |
| 41 | (b) Removing old broken damaged hasp of locker steel and S&F new hasp & stapples of size 150mm long chromium plated for the shutters of steel locker complete, all as directed by Engr-in-Charge and shown on drg. |
| 42 | (c) Removing old broken handle of locker steel and S&F new handle of size 100mm long \"D\" Type chromium plated to the shutters of locker steel. |
| 43 | (d) Removing old broken hanging rod of locker steel and S&F new hanging rod made out of 20mm dia chromium plated pipe of size 500 mm long for locker steel, all as directed by Engr-in-Charge and shown on drg. |
| 44 | (e) All as per item No 1.07 but for Locker steel, all as directed by Engr-in-Charge and shown on drg. |
| 45 | Table office officer steel (a) Removing old broken damaged top of table officer steel and S&F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top complete, all as directed by Engr-in-Charge and shown on drg. |
| 46 | (b) Removing old u/s internal drawer locks from steel table office and S&F new internal drawer locks 40 mm, all as directed by Engr-in-Charge and shown on drg. |
| 47 | (c) Removing old u/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00 mm thick, all as directed by Engr-in-Charge and shown on drg. |
| 48 | (d) Taking out of u/s worn out drawer-shutter and providing the new one of existing size and shape made out of MS short 1.00 mm thick, all as directed by Engr-in-Charge and shown on drg. |
| 49 | (e) Repair of drawer and wron out welding in drawer in its original position in existing size and shape, all as directed by Engr-in-Charge and shown on drg. |
| 50 | (f) Removing old broken u/s hard rubber shoes of table office for officer steel and S&F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of tabile office officer steel complete, all as directed by Engr-in-Charge and shown on drg. |
| 51 | (g) All as per item no 1.07 but for table office officer steel, all as directed by Engr-in-Charge and shown on drg. |
| 52 | Table office clerk steel(a) Removing old broken damaged top of table office clerk steel and S&F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with19x4mm teakwood beading duly french polished all around the top, all as directed by Engr-in-Charge and shown on drg. |
| 53 | (b)Removing old U/S internal cupbord/weter locks from table office clerk steel and S&F new internal locks 400 mm 4 lever with dupicate keys of approve quality, all as directed by Engr-in-Charge and shown on drg. |
| 54 | (c)Taking out of U/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00 mm thick, all as directed by Engr-in-Charge and shown on drg. |
| 55 | (d) Repair of drawer and worn out welding in drayer into original position in existing size and shape, all as directed by Engr-in-Charge and shown on drg. |
| 56 | (e) Removing old broken u/s rubber shoes of table ofice clerk steel and S&F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of table office clerk steel, all as directed by Engr-in-Charge and shown on drg. |
| 57 | (f) All as per item no 1.07 but for tabile office clerk steel, all as directed by Engr-in-Charge and shown on drg. |
| 58 | Repair/re-canning of chair varandah(a) Remove of old caning from the steel frame of chair varandah and making the frame by means of welding wherever required to bring its in original shape, all as directed by Engr-in-Charge and shown on drg. |
| 59 | (b) Removing old broken u/s hard rubber soes of chair varandah and S/F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of chair varandah complete, all as directed by Engr-in-Charge and shown on drg. |
| 60 | (c) De-rusting/cleaning the iron frame to smooth surface and painting all steel surface with two coat of synthetic enameled white paint over a coat of red oxide primer to bring the surface with glossy finish and re-caning the same with 4mm white plastic cane make-Ajoy/Primer oval shape as approved by GE as per drg and providing the new rubber shoe complete, all as directed by Engr-in-Charge and shown on drg. |
| 61 | Charpoy Hard Top MAP(a) Remove the existing unserviceable ply wood from charpoy with ply and making the frame to its original position by tightening etc and supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size, all as directed by Engr-in-Charge and shown on drg. |
| 62 | (b) All as per item No 11.01 here-in-before but for charpoy Hard Top, all as directed by Engr-in-Charge and shown on drg. |
| 63 | Table dining 6 Pers (MAP)(a) Removing old broken damaged top of table dining OR and S&F new top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exerior grade with 19x4mm teakwood beading fixed with headless nails all around the top.Top will be covered with Almn steel 20 gauge, all as directed by Engr-in-Charge and shown on drg. |
| 64 | (b) Removing old & U/S legs of table dinning 6 pers & S/F new legs of size 750x45x90mm made out of 1st class well seasoned teakwood duly fixing PVC rubber shoes at the bottom of legs with mild steel screws complete, all as directed by Engr-in-Charge and shown on drg. |
| 65 | (c ) Taking out old & U/S long rail and S/F new leg rail of size 1500x45x90mm made out of 1st class well seasoned teakwood complete, all as directed by Engr-in-Charge and shown on drg. |
| 66 | (d) All as per item No 12.02 here-in-before but short top rail of size 900x45x90mm, all as directed by Engr-in-Charge and shown on drg. |
| 67 | (e) Removing old & U/S MS right angle from the corner of table dining 6pers and providing and fixing new one of size 150x30x5mm with mild steel screws complete, all as directed by Engr-in-Charge and shown on drg. |
| 68 | Table Writing(a) Remove the old top and providing the new top made out of 18mm particle board one side laminated exterior grade with 4mm teak wood beading all around and fixing the same on top of table writing in its original position as per drg, and providing new hard rubber/PVC/Nylon shoes to the bottom of legs, all as directed by Engr-in-Charge |
| 69 | (b) Taking out old U/S sides of table writing and S/F new sides made out of 19mm prelaminated particle board one side teak veneered complete, all as directed by Engr-in-Charge and shown on drg. |
| 70 | (c) Removing of old U/S shutters of table writing and S/F new shutter made out of 19mm thick prelaminated particle board one side teak veneered bonded with phenol formaldehyde exterior gde including fixing of new or old serviceable hinges 50mm MS medium wt complete, all as directed by Engr-in-Charge and shown on drg. |
| 71 | (d) Taking out old & U/S drawers from table writing and S/F new drawers made out of prelaminated particle board & 1st class well seasoned teakwood for sides & 6mm thick commercial plywood for bottom of drawers complete, all as directed by Engr-in-Charge and shown on drg. |
| 72 | (e) Removing of U/S MS hinges from shutters and S/F MS butt hinges 50mm medium wt cold roller mild steel, all as directed by Engr-in-Charge and shown on drg. |
| 73 | (f) Removing of u/s knobs from shutters & drawers of table writing and supply & fix new 35mm round brass knob of approved quality complete, all as directed by Engr-in-Charge and shown on drg. |
| 74 | (g) Taking out old & U/S plywood back of table writing & S/F new 6mm thick 5 plywood commercial BWR gde type BB fixed with 20mm mild steel screws complete all as directed & shown on drg. |
| 75 | (h)Taking out old U/S long legs of table writing and S/F new long legs made out of 1st class teak wood complete, all as directed by Engr-in-Charge and shown on drg. |
| 76 | (j)All as item No 13.08 mentioned here-in-before but short legs of table writing, all as directed by Engr-in-Charge and shown on drg. |
| 77 | (k) Remove the old existing long stiffener of table writing and S/F new long stiffner made out of 1st class well seasoned teak wood of existing shape & size and making functional, all as directed by Engr-in-Charge and shown on drg. |
| 78 | (l) All as per item No 13.10 mentioned here-in-before but short stiffners of table writing, all as directed by Engr-in-Charge and shown on drg. |
| 79 | (a) Removing of old worn out u/s bottom wnd bearers of sofa set 3/5 seater and providing/fixing new one made of teak wood seasoned in existing shape and size, all as directed by Engr-in-Charge and shown on drg. |
| 80 | (b) remove the existing unserviceable sofa cushion from sofa set 5 seater and supply and fixing the new cushion 100 mm thickx40 density of size 530x560 mm coverd with new tapestry cloth duly sitched, all as directed by Engr-in-Charge and shown on drg. Make - kurlon/sleep well |
| 81 | (c) All as per item 14.02 here in before but for sofa set 3 seater, all as directed by Engr-in-Charge and shown on drg. |
| 82 | Sofa set 2 Seater (a) Removing of old worn out u/s front leag of sofa set 2 seater and providing/fixing new one made of teak wood seasoned in existing shape, all as directed by Engr-in-Charge and shown on drg. |
| 83 | (b) Removing of old worn out u/s rear leag of sofa set 2 seater and providing/fixing new one made of teak wood seasoned in existing shape, all as directed by Engr-in-Charge and shown on drg. |
| 84 | (c ) Removing of old worn out u/s front rail of sofa set 2 seater and providing/fixing new one made of teak wood seasoned in existing shape, all as directed by Engr-in-Charge and shown on drg. |
| 85 | (d) Removing of old worn out u/s back rail of sofa set 2 seater and providing/fixing new one made of teak wood seasoned in existing shape and size, all as directed by Engr-in-Charge and shown on drg. |
| 86 | (c ) All as per item 14.02 here in before but for sofa set 2 seater, all as directed by Engr-in-Charge and shown on drg. |
| 87 | Rack steel 6 Tier(a) Removing of unsv worn out back of rack steel and S&F new back rack steel closed type made sheet 1mm thick of existing shape and size and makng functional, all as directed by Engr-in-Charge and shown on drg. |
| 88 | (b) Removing of unsv sides of rack steel and S&F new sides made of 1 mm thick MS sheet in its original position as per drg & making functional, all as directed by Engr-in-Charge and shown on drg. |
| 89 | © Removing of unsv shelves of rack steel and S&F new shelves made of 1 mm thick MS sheet in its original position as per drg & making functional, all as directed by Engr-in-Charge and shown on drg. |
| 90 | (d) Removing of unsv MS angel iron from rack steel and S&F new MS angel iron to rack steel close typein its original position as per drg & making functional, all as directed by Engr-in-Charge and shown on drg. |
| 91 | (e) All as per item No 1.07 here in before but for Rack steel, all as directed by Engr-in-Charge and shown on drg. |
| 92 | Table 900x600mm with drawer(a) Remove the old top and providing the new top made out of 18mm partical board one side laminated exteroir gread with 4 mm teak wood brading all around and fixing the same on table in its original position as per drawing and poviding new hard rubber/PVC/Nylon shoes to the bottom of legs.Size of particle board shall be 900x600mm, all as directed by Engr-in-Charge and shown on drg. |
| 93 | (b) Removing old u/s following components of table 900x600xmm with or without drawer & S/F with new components made out of 1st class well seasoned teakwwood free from knots,crecks,sapwood etc, all as directed by Engr-in-Charge and shown on drg. |
| 94 | (i) Legs (Size 740x60x30mm), all as directed by Engr-in-Charge and shown on drg. |
| 95 | (ii) Long rails (740x25x65mm), all as directed by Engr-in-Charge and shown on drg. |
| 96 | (iii) Short rails (440x25x65mm), all as directed by Engr-in-Charge and shown on drg. |
| 97 | (c ) Removing old u/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00 mm thick, all as directed by Engr-in-Charge and shown on drg. |
| 98 | (d) Taking out of u/s worn out drawer-shutter and providing the new one of existing size and shape made out of MS shrrt 1.00 mm thick, all as directed by Engr-in-Charge and shown on drg. |
| 99 | (e) Repair of drawer and wron out welding in drawer in its original position existing size and shape, all as directed by Engr-in-Charge and shown on drg. |
| 100 | Charpoy GI pipe with ply top(a) Remove the existing u/s ply wood from Charpoy GI Pipe and making the frame to its original position by tightening etc and supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape, all as directed by Engr-in-Charge and shown on drg. |
| 101 | (b) Removing the unserviceable/broken check nuts from GI Charpoy & S/F 6mm thick GI medium grade check nuts suitable for 32mm dia GI pipe, all as directed by Engr-in-Charge and shown on drg. (Each check nut will be measured as single unit) |
| 102 | (c )Removing the unserviceable broken 3 way GI elbow from GI charpoy and S&F 32mm dia GI medium grade 3 way elbow ISI marked all as specified, all as directed by Engr-in-Charge and shown on drg. (Each GI Elbow be measured as single unit) |
| 103 | (d) Removing the existing unserviceable/broken long rail from GI charpoy and S&F new long rail of GI tubing 32mm including cutting threading and bringing the GI charpoy into the original shape, all as directed by Engr-in-Charge and shown on drg. (Make : TATA/JINDAL) |
| 104 | (e) Making short rails obtained from item No 18.40 above and fixing, all as directed by Engr-in-Charge and shown on drg. |
| 105 | (f) Making legs out of u/s long/short rails obtained from item 18.04 and 18.05 above including cutting, threading and fixing, all as directed by Engr-in-Charge and shown on drg. |
| 106 | Table 900x600x760mm steel(a) Removing old broken damaged top of table 900x600x760 mm steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top, all as directed by Engr-in-Charge and shown on drg. |
| 107 | (b) Removing the existing steel long rail from Table 900x600x760mm and S/F new steel long rail of size : 25mm x 25mm x 1.6mm thick, all as directed by Engr-in-Charge and shown on drg. |
| 108 | (c ) Removing the existing MS legs from Table 900x600x760mm and S/F new long made out of25mm x 25mm x MS tube 1.6mm aeli thickness, all as directed by Engr-in-Charge and shown on drg. |
| 109 | (d) Removing the existing stiffner bottom and S/F new stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm wall thickness, all as directed by Engr-in-Charge and shown on drg. |
| 110 | (e) Remove the existing short stiffner and S/F new short stiffner made out of 25mm x 25mm, MS tube of 1.6mm wall thickness All as directed by Engr-in-Charge and shown on drg. |
| 111 | (f) Remove the existing unserviceable shoes from Table 900x600x760mm and S/F new PVC shoes suitable for 25x2mm MS tube, all as directed by Engr-in-Charge and shown on drg. |
| 112 | (g) M&L painting (Remove the existing worn out paint from table 900x600x760mm and applying one coat of synthetic enamell paint black over a coat of primer, all as directed by Engr-in-Charge and shown on drg. |
| 113 | Table Marble top Replace the U/s marble top with new 20mm th marble with nosing Exc 0.6 Sqm but not exc 1.2 Sqm, all as specified and directed by Engr-in-Charge. |
| 114 | Chair Writing Steel Replace the following parts of chair writing steel as shown in drawing and directed by Engr-in-Charge (Drg No FD-280) (a) Seat shall be 12mm thick hot pressed plywood upholstered with febric and moulded polyurethens foam with PVC lipping all round.The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20kg on humpden machine, all as directed by Engr-in-Charge and shown on drg. |
| 115 | (b) Back shall be 12mm thick hot pressed plywood upholstered with febric and moulded polyurethene foam with PVC lipping all round.The polyuethene form shall be 50mm thick and shall be moulded with density 50-55kg per cubic meter thick and hardness 20kg on humpden machine, all as directed by Engr-in-Charge and shown on drg. |
| 116 | (c) Hand rest shall be made of black integral skin polyurethene with 75-85 shore \"A\" Hardness & Reinforced with MS insrest.It sahll be scratch and wheather resistant size 210mm (inner) and 230mm (outer), all as directed by Engr-in-Charge and shown on drg. |
