|
| 1 | First class B/w in 1:4 Cement C\"sand mortor in Sub Structure including supply of all meterial labour t&P etc required for proper completion of work |
| 2 | 12 mm thick Plaster with cement & course Sand of 1.25 FM Mortar in 1:4 |
| 3 | M.S. or iron work of small sizes and section such as holding down bolts, hold fast, tie rods grating etc. wrought to required from including supply of steel bolts, nuts wastage etc. and their fixing required for proper completion of the work |
| 4 | Apply two coat superior synthetic enamal paint including primer coat on steel surface |
| 5 | Providing and applying plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 6 | Finishing wall with weather coat paint (Asian or Berger Brand) on new surface with two coat to give an even shade including supply of all material, labour & tools and plants etc. requiredfor proper completion of the work. |
| 7 | Earth work in filling with ordanry soil including lead up to 30 mtr and lift up to 1.5 mtr, including extra cartage up to 8.00 km |
| 8 | Providing and laying cement concrete in 4:2:1 of not less than strength of M-150 stone ballast (20 mm nominal size), approved coarse sand and cement, curing complete including of cost of form work in foundation and floors-completion of the work as per direction of the E / I. |
| 9 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement |
| 10 | Supply & Fixing Garden Bench (Victoria Type Bench)•Cast Iron having back height of 720 mm and seating height of 390 mm.•M.S Tube of 65mm X 25mm rectangular tube having length of 1520 mm in 10 Nos. •For seating purpose with extra support 25mm X 5mm M.S Flat for extra stability all sharp and rough edge of Bench are to be grinded with grinder and all fill up with m seal where its required necessary thus bench is having the provision of hole past system (for grouting). •Bench in complete with a coating of 1st class red oxide and with two coats of synthetic enamel of 1st class quality paint in green colour. •Finally bench is assembled with nuts and bolts. •Gross weight of each bench is 70 kg. |
| 11 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 mm cum |
| 12 | Rough dressing the trenched ground including breaking clods. |
| 13 | Fine dressing of the ground. |
| 14 | Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of officer in charge |
| 15 | Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. |
| 16 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sq. mm 2 core |
| 17 | fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 and above Protection complete in all respect. |
| 18 | S&F of 63 Amp. DP MCB |
| 19 | Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing. |
| 20 | Supply and fixing of one number 8 SWG G.I. wire in 15mm dia. G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. |
| 21 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 6 sq. mm 2 core |
| 22 | Supply and laying of 50mm dia heavy guage 14 SWG (2 mm thick) rigid steel conduit complete with bend and other acessories as required and 14 SWG fish steel wire etc. in slab alongwith reinforcement before concreting, and plastering etc,complete in all respect |
| 23 | S/F of 50mm dia B class G.I pipe |
| 24 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. |
| 25 | S&F of 63 Amp. four pole change over switch on a angle iron frame, including the cost of labour, T&P, painting and other material required for propercompletion of the work |
| 26 | Dismentling existing C.Conc Road & Interloking road. i/c all comp. of work |
| 27 | Laying &compacting dry O.B.B 40cm gauge in foundation in layer. Thickness including local sand. |
| 28 | laying old interloking labour rate only |
| 29 | Supply of 90 W LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 and above Protection complete in all respect. CAT- AAA, with LM 79-08 & LM 80-08 report of NABL, 5 years replacement guarantee/ warranty, BIS certificate & AAA catagary certified by pwd. as per pwd schedule no. -1423 |
| 30 | Supply of 150 W LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 andabove Protection complete in all respect. CAT- AAA, with LM 79-08 & LM 80-08 report of NABL, 5 years replacement guarantee/ warranty, BIS certificate & AAA catagary certified by pwd |
| 31 | Making of graden hut R C C with wooden look in square shape dia 3.50 meter height 3.4 Mtr on four piller circumference 85 cn with wooden touch with round shape cementing with main path way by cc path and floor and foundation work complete jobe with wooden touch making and fixing of R C C logs wooden touch height up to 45cm for sitting propose and suitable for landscaping as directed by officer in charge as per attached photo graph including materials & labour etc. (AR) |
| 32 | Provision of Platform for base (AR) |
| 33 | CHIMPU/POLO BEAR/PENGUIN DUSTBIN 110 Ltr. |
| 34 | AIR WALKER : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDING PURPOSE 5 FT X 2 FT X 4.5 FT [MR] |
| 35 | CROSS WALKER : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDING PURPOSE 5 FT X 2 FT X 5 FT. [MR] |
| 36 | SINGLE POLE CYCLE : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDING PURPOSE 3.5 FT X 2 FT X 4 FT |
| 37 | SIT UP STATION : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDING PURPOSE 4.5 FT X 4.5 FT 2 FT [MR] |
| 38 | SEATED CHEST PRESS : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDING PURPOSE 7 FT X 6 FT X 3 FT. |
| 39 | PUSH OR PULL CHAIR : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDING PURPOSE 7 FT X 6 FT X 3 FT |
| 40 | TRIPLE TWISTER : MAIN FRAME - 4 INCHI 114 OD GI B CLASS OF ISI MARK, THICKNESS OF 3 MM, OTHER CONNECTING PIPES, 41 OD B CLASS GI, 32 OD B CLASS GI, ALL MACHINES ARE FITTED ON LOCK, BEARING OF KG COMPANY OR SIMILAR WILL BE USED BEARING, SIZE 6205 ZZ, ALL MACHINES ARE POWDER COATED FOR GIVING EXTRA LIFE, AND WILL BE HEAT AND WATER RESISTANT, SEATS CAP AND FOOTREST IS OF ALUMINIUM CASTED, 25 MM IRON ROD IS USED IN BEARING SHEET, 10 MM FLENGE OF 200 MM DIA IS USED TO FIX THE, MACHINES, GAS METAL ARC IS USED FOR ALL WELDINGB PURPOSE 4 FT X 4 FT |
| 41 | Providing of 3D wall painting with picture including of making base of all work complete. |
| 42 | Supply and Fixing inoguration black granite stone padestal including grooving matter, brick work, plaster, painting etc. all complete |
| 43 | GST 18 % Please Enable Macros to View BoQ information |
