|
| 1 | Surface excavation n. exc (not exceeding) 30cm deep and averaging 15cm deep and geeting out hard/dence soil |
| 2 | Excavation in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. or for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc, n exc 10 sqm on plan and n exc 1.50m in depth and getting out hard/ dense soil. |
| 3 | Excavation in trenches, for each additional 1.5m or part thereof in depth beyond the first 1.5 m in depth and getting out hard/ dense soil. |
| 4 | PCC (1:4:8) type D-2 using 40mm graded stone aggregate in fdn, filling/mass concrete |
| 5 | Returning, filling, ramming incl.spreading, leveling, watering & well ramming in layers n.exc 25cm thick in hard/dense soil |
| 6 | Removing excavated material not exc 50mtr and depositing where directed at a level not exc 1.50mtr above the starting point in soil |
| 7 | M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm gradedaggregate)Foundations, including rafts,footings, foundation beams;plinth beams; bases for columns, etc.;basement slabs, under-reamed piles and mass |
| 8 | M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm gradedaggregate)Beams, cantilevers, bressummers,lintels over 1.5m span |
| 9 | M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm gradedaggregate)Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified |
| 10 | M&L for RCC (nominal mix) Type B1 1:2:4 (20 mm gradedaggregate) Columns, pillars, piers, posts and struts all as specified |
| 11 | M&L forMild steel TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 12 | M&L forMild steel TMT bars 6mm to 8mm dia , cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed |
| 13 | M&L Formwork to sides of concrete foundations, footing, basis of coloumns , raft & raft beams,, sides & soffits of foundation & plinth beams and similar work vertical or to batter, rough surfaces of concrete complete all as specified and as directed |
| 14 | M&L Formwork to Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough surfaces of concrete complete all as specified and as directed |
| 15 | M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. ® |
| 16 | M &L Brick work with sub class\"B\" bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6, complete, all as specified and as directed. |
| 17 | M &L For Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4CM |
| 18 | Rendering 15 mm thick in CM 1:4 on fair faces of concrete surfaces finished even and fair with out using extra cement all as specified. |
| 19 | Rendering 15 mm thick in CM 1:6 other than fair faces of concrete surfaces finished even and smooth with out using extra cement all as specified. |
| 20 | S & F Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. in posts and struts including cutting tops to shape as directed Fe-290(Gde E-165) |
| 21 | S&F MS Angle Iron as in rolled sections as in main and cross beams,hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates Fe410-W(Gde-E-250 quality-A) |
| 22 | Painting to steel surfaces of any description over 10cm in width /grith with two coats of synthetic enamel paint over one coat of red oxide primer incl. prepartion of new/Old steel surfaces |
| 23 | M&L for two coat cement base paint over a coat of alkali resist priming paint including preparation of wall surface complete all as directed by Engineer-in-Charge. |
| 24 | S &F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /claddingto wall , fixed with self tapping screws as specified |
| 25 | M&L for 75 mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate in for sub base all as specified. |
| 26 | M&L for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate in plinth protection paving surfaces including finishing surface even & smooth |
| 27 | M&L for Sand filling under floors or in foundations including watering and consolidation all as specified. |
| 28 | S & Fglazed ceramic tiles in vertical surface,coloured, of size 450mmx 350mm x7 to 8mm thick onvertical surfaces such as dados,skirting etc., set and jointed with approved adhesive,including 10 mm thick rendering cement plaster in 1;4 CM and pointed in white cement with pigment to match all as specified. |
| 29 | M & L for rectified coloured Non Skidceramic tiles of size 400x400x 7-8mm as in floors, set and jointed in neat cement slurryas per manufacturers instructions and pointed in white/ coloured cement, laid over and including cement screed bed 25mm thick in cement mortar 1:6, complete all as specified. |
| 30 | M and L Providing & Fixing False ceiling with semi perforated 12mm thcik micro tegular edged at all heights with GRG (Glass Fibre reinforced Gypsum) false ceiling tiles for temp buildings/PMT Bldgsof size 595x595mm of approved texture, design and pattern having moisture content less than 2%,humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 475 (part-4)-1970 and light Code Description unit rate No 429 SUB HEAD :26.0 NEW TECHNOLOGIES AND MATERIAL reflectance of 85% minimum to be laid in true horizoatal level suspended on interlocking metel T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 grams oer sqm including both sides) comprising of main-T runners of size 15x32mm of length 3000mm, vross-T of size 15x32nn of lenght 1200mm amd secondry itermediate cross-T of size 15x32 of lenght 600mm to form grid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanising @ 80 grams per sqm) ie. 50mm long, 8mm outer diameter M-6 dash fasteners or 3 to 4 mm GI hanging wire for temp Bldg length/ht as per site req ,6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm.Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000mm to be fixed on perimeter wall/partition with the help of plastic rawl pluhs at 450mm center to center and 40mm long dry wall screws. The work shall be carried out as per specification, drawing and as per direction of the Engineer-incharge. |
| 31 | Excavating in post holessoft/loose soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, |
| 32 | M&L for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) includingdistance pieces, cleats etc.Fe 410-W (GdeE- 250) quality A all as specified and directed. |
| 33 | M&L for 100mm thick PCC (1:4:8) Ty D2 as in sub base over rammed earth. |
| 34 | M&L for cement concrete 1:2:4 type B1(using20mm graded stone aggregate) as in blocks for hold fast, coping,benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete allas specified. |
| 35 | M&L 25 mm thickPCC 1:2:4, type B-0 using 12.5mm graded crushed aggregates as in floor surfaceall as specified and directed. |
| 36 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, all as specified. |
| 37 | M&L for joint less Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including provn of 15mmthick screed bed or bedding layer in CM 1:6 etc complete all as specified . |
| 38 | S&F Modular Cabinet Kitchen accessoriesof Stainless Steelgrade-304,6mm size rod thicknessincluding :-(i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket,(iv) Cup & saucer basket, (v) Glass basket,(vi) Plate basket, (vii) Premium magic corner(viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all spd and directed by Engr in charge |
| 39 | S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbmhaving good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets. |
| 40 | S & F50 mm dia Galvanised Iron steel tubing, medium grade as in spout in short length, complete all asspecified. |
| 41 | S&F in Soft closing ball bearing telescopic channel of size 22 inch long fixed with screws in cupboards incl all fittings complete all as spd and directed by Engr in charge.Note : Runner/ Channel should be SS 304 grade and load capacity should not be less than 45 kgs |
| 42 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for |
| 43 | M&L for PCC( 1:3:6) type C-2 using 20mm graded stoneas in padding on roof correction of slope and roof kerbs all as specified and directed. |
| 44 | M&L providing and applying the plaster with single component ready to use repair mortar (SMART CARE REPAIR MORTAR or equivalent) capable of applying 15mm average thickness in single layer and finishing with trowel with a bond coat: SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area mixed with specified portion of AP SMARTCARE or equivalent Repair Polymer including taking down existing roof treatment of any type including raking out joints, hacking for key, scrubbing down with water etc., to receive further treatment, complete all as specified land as directed.Note: The application shall be executed on any type of surface and on horizontal/Vertical areas. |
| 45 | M&L providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajas in multiple coats @2.0 litre/sqm. Primary [coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge.Notes: (1) The work shall be executed through authorised applicator of manufacturer only.(2) Authrised Applicator shall be approved by GE before starting of work.(3) All materials shall be procured directly form manufacturer. The purchase voucher shall be produced to the Engineer-in-Charge for his verification of material.Engineer-in-Charge shall deface the original purchase vouchers.(4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Ten years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor\"s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer. |
| 46 | S & F Expanded metal n exc 4 kg weight per square meter, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members all as specified and directed. |
| 47 | M & L Machine pressed precast concrete PU coated colourinterlocking paver block any shape and size, with grey cement and pigment confirming to IS 5658-2006 of 80 mm thicknessM-40 Grade complete all as specified |
| 48 | S&F powder coated Anodiesed aluminium frame for partition, doors, windows, ventilators with one or more rebates incl. joining cleat for fixing etc. complete all as specified. |
| 49 | S&F powder coated Anodiesed aluminium door shutters, aluminium section weighing 0.55 Kg/m incl. necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each doors,Brass 2 lever mortice lock verticle type size 100mm, hinges, anodiesed aluminium snap beading screw withetc. |
| 50 | Supply and fixing PVC sheet consisting of 5mm thick light colour PVC sheet inclusive of fixingon PVC frame /Aluminium frame at site etccomplete all as specified and as directed by Engineer-in- charge. |
| 51 | S&F powder coated not less than50micron Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 52 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS :1868 with minimum anodiccoating of grade AC 15) of approved design/pattern, with approved stadandered section and fixed to existing window frame with CP brass/stainless steel screws @200mm c/c, incl cutting the grill to proper opening size for ficing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement and direction of Engineer-in-charge. |
| 53 | S&F door closer aluminium (extruded section) hydraulically regulated designation No. 03, universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 Kgs. |
| 54 | Supply and fixing Floor door stopper 140mm long of aluminium alloy and tongue, anodised with hard drawn steel spring fixed in floor etc completeall as specified & directed by Engineer-in-charge. |
| 55 | S&F 4.8 mm thick sheet glass, ordinary quality and glazing in Aluminium door with solar control files 50 micronin any size each pane. |
| 56 | S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm & fixed with tinned tacks or galvanised wire staples. |
| 57 | M&L, PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in post hole, foundation, fitting and mass concrete |
| 58 | Dismantling and Re-Fixing only chain link fencing incl line wires, any mesh, size and type to any type of standereds, rails, straining blots, etc. incl provn of binding wire. |
| 59 | Supply only chain link MS galvanised fencing any size (75x75mm)or any type complete. |
| 60 | M&L, two coats of synthetic enamel paint to untreated surfaces of steel any size width or girth not otherwise described over a coat of red oxide primer after preparation |
| 61 | S&F 2mm thick fibre glass reinforced translucent plain sheeting withside lap fixed with srew. |
| 62 | Material and labour for preparation of new/old plastered surfaces as of walls and applying Twocoats of weather proofing exterior acrylic emulsion paint of DULUXWeather shield Max or APEX ULTIMA from Asian paint over one coat putty over one coat of primer from the same manufacturercomplete all as specified and directed. |
| 63 | M&L hard core of broken stone of gauge n. exc. 63mm; deposited, spread and levelled in layers n. exc. 15cm thick watered and rammed to true surface complete all as specified and directed by Engineer-in-Charge. |
| 64 | M&L chequered tiles 30cmx 30cmx 22-25mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 15mm thick screed in cement mortar 1:6 |
| 65 | S&F mild steel, plain black sheet 1.25mm thick in wall clading, steel gates incl round headed screws, clout nails or rivets and fixed to wood or steel framing. |
| 66 | S&F75mm long, extrruded fancy type SS handle for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts, screw and washer of mild steel bright finished, complete all as specified. |
| 67 | S&F in repairs magnet catchesand striking plate including letting in and fixed, complete all as specified. |
| 68 | S&Ffactory made uPVC white colour three track three panels sliding window with flyproof S.S. wiremesh ( Two nos. glazed & one no. wiremesh panels ) upto 1.50m ht made of big series frame 116 x 45mm & sash 46 x 62mm both having wall thickness of 2.3 + 0.20mm and single glazing bead/ double glazing beading of appropriate dimension ( Area of window upto 2.0 sqmtr) comprising of uPVC multichambered frame and mullion (wherevr required) extruded profile duly reinforced with 1.60 +0.20mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropraiate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless screw etc.Profile of frame & sash shall be miterd cut and fusion welded at all corners, mullion (if reqd) shall be also fusion welded including 5mm thick toughened glass and SS wire mesh fixed and drilling holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of reqd size and approval quality, all complete as per approved drg and direction of Engr in charge. Note: For uPVC frame, sash and mullion extruded profiles ,minus 5% tolerance in dimension i.e depth and width of profile dimension in higher side shall be acceptable but no extra payment on this account shall be made |
| 69 | M&L for 50mm thick PCC 1:3:6 type C2 using 20mm graded stone agg as in sub base complete all as specified.. |
| 70 | M&L for Powder coated aluminium(minimum thickness of powdercoating 50 micron) work for doors,windows, ventilators and partitions with PVC sheet (sliding window with three track) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up thegaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 71 | M&L for PVC insulation tjickness of PVC insullation panels 40mm with EPS stuck to 1mm plain PVC sheetsuitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing directed by Engineer-in- Charge |
| 72 | M&L for PVC false ceilings 6mm are watertight, just like gypsum false ceilings, and are more effective and lasting in high moisture environments like balconies, bathrooms, and basements |
| 73 | M&L mild steel round bars 10 mm dia conforming to FE-410-W (Gde E-250) quality A or Fe-290 (Gde E-165) for use in chain link fencing as wind tie all as specified. |
| 74 | Mild steel screw bolts(machine made) with hexagonal or square heads at one end screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 30 cm and dia of neack exc 12 mm but not exc 20 mm complete all as specified and as directed by Engineer-in-Charge. |
| 75 | Taking down care fully copper/aluminium point wiring from caping/casingor conduits (light, fan, socket or power) complete incl fittings such as switches, sockets, ceiling roses, pendents, regulators, light fittings any type etc to be measured seperately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed by Engineer in charge. |
| 76 | M & L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including in and including concealed / surface PVC conduits as suitable of site Medium gradeofISI Marked not less than 20 mm dia and all conduit accessories concealed in wall on surface in ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated modular metal flush box, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified. |
| 77 | All as per Item No 76 above but one light/fanpoint controlled by one by one way switch. |
| 78 | All as per Item No 76 above but one 3 pin socket outlet 5 hole 5 Amp independent board , socket & switches to be measured and paid separately. |
| 79 | All as per Item No 76 above but with 2.5 sqmm single core FRLS copper cable. |
| 80 | All as per item No 76 above but one 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board |
| 81 | One power point with insulated stranded copper conductor cable 4 Sqmm single core for 3 pin 15 Amp switch socket and PVCinsulated FRLS 1100 Volts unsheathed copper conductor 4 Sqmmin and including new PVC conduit medium grade not less than 20 mm dia, stranded conductor as earth wire connected to dolly complete. |
| 82 | M&Lswitch modular type 6 Amp SP one wayISI marked complete all as specified Make : Havells/Legrand/Roma |
| 83 | M&L socket outlet 5 pin 6 Ampsmodular type ISI marked complete all as specifiedMake : Havells/Legrand/Roma |
| 84 | M&L switch modular type 16 Amp SP one wayISI marked complete all as specifiedMake : Havells/Legrand/Roma. |
| 85 | M&L socket outlet 2 in 1,3 pin 6/16 AmpsISI marked complete all as specifiedMake : Havells/Legrand/Roma. |
| 86 | M&L ceiling rose 3 terminals PVCpolycorbonate,isolated body. complete all as specified. |
| 87 | S & F modular electronic fan regulator 5 step connecting complete all as specifiedMake : Havells/Legrand/Roma |
| 88 | Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts with lifetime of 25000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.90, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1,Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 100 Lumens/watt andincluding connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete. |
| 89 | S&F fresh air fan PVC body air delivery > 800 CMH , 5 number of blades, AC single phase 230/240 V of size 250 mm sweep with louvre fixed complete with suitable size ply by cutting into suitable size as required complete all as specified and directed by Engr-in-Charge. |
| 90 | S&F Modular socket outlet 2/3 pin 6 Amp socket 2 module complete all as specified and directed by Engineer in charge. |
| 91 | M&L for breaking old existing wall and making a provn for fixing of 160 mm Electric Chimany pipe including making good to the disturbed wall/ portion and matching with existing colour.all as specified and directed. |
| 92 | Supply and Fixing wall mounted angular Electric chimney black colour of suction power not less than 1220Cum/Hr,Al casette with stainless steel outer layer ,touch control panel,3 speedmotor with 250 watt with decorative smart cooker hood SS and glass ,energy efficent Led light with digital display , including ducting not less than 12 feet as per site required complete all as specified and as directed by Engr-in-Charge Make: Glen/Hindware |
| 93 | Supply and fix wall mounted fan 400mm size, 230 volts , 50 Hz 1420 RPM with 90 degree oscillation and having speed control by pull cord (two) system complete all as specified and directed. |
| 94 | S&F in repair Sub main wiring with two runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistrandedcopper conductor cable with one run of 4 sqmm single core PVC insulated FRLS cable 1100 volts grade, multistrandedcopper conductor cable as earth continuity conductor, drawn through and including 25 mm dia non metallic rigid PVC conduit and conduit accessories on surface of walls complete all as specified and directed. |
| 95 | Supply and fixMCB DB SPN 8-12 way Horizontal, IP-43 Protection double door 240 V AC 50Hz with for MCBSPN as incomer and DP/SP MCBs as out going with tinned copper bus bar ,neutral link earth link completeall as directed. |
| 96 | Supply and fixMCB DB SPN 4 way Horizontal, IP-43 Protection double door 240 V AC 50Hz with for MCBSPN as incomer and DP/SP MCBs as out going with tinned copper bus bar ,neutral link earth link completeall as directed by Engineer-in-Charge. |
| 97 | S&F MCB SPN 63 Amps 240 volts 10 KA \"C\" curve and making necessary electrical connections all as specified and directed. |
| 98 | S&F MCB SP6-32 Amps 240 volts 10 KA\"C\" curve and making necessary electrical connections all as specified and directed.. |
| 99 | Supply,installation, testing and commissioning instant electric water heater with heating element of capacity 3 ltrs complete with all accessories such as safety valve, thermostat, NRV, connection piece etc and connecting with water mixture complete with all other accessories reqd for making water connections all as specified and directed. |
| 100 | M&L in replacement sheet metalenclosure, single pole and neutralwith a two pin and earth plug and socket 240 Volts grade20Amps complete with onesingle poleMCB \"C\" series 10/20 A capacity complete all as specified and directed by Engineer in charge. |
| 101 | S&F 60 W High efficient LED Street light fitting with pressure die cast Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover.System level efficacy of the Luminarie should more than 120 lm/W. The color temperature is around 6500 K with a color rendering index of 70.The luminaire is IP:65 protected.It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, High and low voltage protection along with a surge protection of 4 KV internal including provision of suitable dia GI light grade pipe1.2 meter length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed complete as specified and directed. |
| 102 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 103 | Supply and fixing LED post top light made in die cast aluminium housing and spun aluminium top reflector with decorative PMMA diffuser having IP 65 protection complete of 45/50 watt including making necessary electrical connections and fixing arrangement etc all as required at site and directed by Engineer-in-Charge. |
| 104 | Supply and fixing LED bollard light aluminium extrusion, opal, polycarbonate diffuser for spot free lighting having IP 65 protection complete of 45/50 watt including making necessary electrical connections and fixing arrangement etc all as required at site and directed by Engineer-in-Charge. |
| 105 | S&F wiring with two runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multi strandedcopper conductor cable with one run of 2.5 sqmm single core PVC insulated FRLS cable 1100 volts grade, multistrandedcopper conductor cable as earth continuity conductor, drawn through and including 25 mm dia non metallic rigid PVC conduit and conduit accessories on surface of walls/underground onearth for making electrical connections of bollard lights including necessary excavation and earth work not less than 30cms deep in any type of soil complete all as specified and directed. |
| 106 | M&L tube light grade galvanised with fittings complete to walls and ceiling or laid in floors 40mm dia including all connected accessories to fix gate/garden light fittings with pillar/in ground. |
| 107 | Supply,installation,testing and commissioning of self priming regenerative pump 0.5/0.37 HP/KW, single Phase 220 volt+18%, discharge range 1950-450 LPH, head range 6-21 mtr insulation class ‘F’ of size 25x25mm complete including mounting bracket of angle iron of suitable size with necessary nuts, bolts and washer etc and making electrical connection with suitable size copper multi stranded cable of suitable length and connecting with GI/ uPVC/cPVC water supply line of any dia/size alongwith accessories such as tee,bend, elbow and socket etc including making bypass arrangement for any fault in pump in future to provide uniterrupted water supply to building all as specified and directed at site by Engr-in-Charge. Model No NILE PLUS II of Crompton or equivellent in Kirloskar/Havelles. |
| 108 | Supply and fix electric water heater storage type steel body with SS tank and heating element upto 2 KW capacity 25 ltrs 5 star rating complete with all accessories such as safety valve, thermostat, NRV, connection piece, MS hold fastners not less than 4 inchesand plug top 16 amps etc. and testing on completion all as specified and directed. |
| 109 | Schedule of Credit |
