|
| 1 | M&L for PCC type D-2 1:4:8 (40mm graded aggregate) Cement concretefoundations, filling and massconcrete all complete all as directed by Engr-in-Charge. |
| 2 | M & L for 50mm thick cement concrete (1:3:6) type C-1 ( using 20mm graded agg.) as in floor finishing/Plinth protection cement concrete all as specified and diredtedall as specified and directed by the Engr-in-charge. |
| 3 | M&L for PCC 1:2:4(Nominal mix)(using 20mm gradded aggregate)type B1 using stone aggregate as in coping benching all as specified and as directed by Engr-in-Charge. |
| 4 | M&L liquior finish/glossy finish Machine pressed precast concrete interlocking paver block rubber moulded laid with Grey cement and pigment any size and shape conforming to IS 15658-2006 of 60mm thick M-35gradeover and including 50 thick sand cushion etc complete all as specified anddirected by Engr-in-Charge. |
| 5 | S & F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified compete all as specified and as directed by Engineer-in-Charge. |
| 6 | S & F of pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified compete all as specified and as directed by Engineer-in-Charge. |
| 7 | S&F for rolled sections as in main and cross beams, hip and jack rafters; purlins,Truss, Gusset plate and base plates, where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, Fe-410-Wgde -E-250) quality \"B\" includng welding or riveting etc complete all as specified and as directed |
| 8 | M & L for brick work with sub class \"B\" old size brick straight or curved on plan exc 6m mean radius built in cement mortar (1:6) all as specified and directed. |
| 9 | Material & Labour for 15mm thick rendering in Cement Mortar 1:4 onbrick work or concrete surfaces, finished even and smooth without using any extra cement complete all as specified and as directed. |
| 10 | M&L for preparation of new surface and and applying two coats of cement base paint over a coat of chalk whiting on walls all as specified and as directed. |
| 11 | M&L for painting new steel Surfaces of any description, over 10cm in width or girth with two coats of synthetic enamel paint paint over and including with red oxide, Zinc chorme primer all complete all as directed |
| 12 | Excavation in trenches in hard/dense soil n.exc 1.5 mtr wide and n.exc 1.5 mtr deep & getting out soil for taking out/laying of cables/foundation, footing etc.complete all as specified & directed by Engr-in-Charge. |
| 13 | Returning, filling in, including spreading, levelling watering and well ramming in layers not exc 25 cm.complete all as specified & directed by Engr-in-Charge. |
| 14 | Removing excavated mateials n.exc 50 mtr & depositing where directed at a level n.exc 1.5 mtr above the starting point.complete all as specified & directed by Engr-in-Charge. |
| 15 | Supply and laying new dry river sand laid in trenches 8 cm below the cable and 15 cm above the cable and punned to 18 cm as cable cushioning and cover complete all as specified and as directed. |
| 16 | Supply and laying of brick well burnt locally available sub class \"B\" laid over sand cushioning for cable protection in trenches width of brick perpendicular to the length of cable, complete all as specified and directed by Engr-in-Charge. |
| 17 | Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm, 3.5 core as per IS 7098 incl. lugs/clamps for mounting on walls/floors,etc other accessories necessary for installation incl. cable route marker, complete all as specified and directed by Engr-in-Charge. |
| 18 | M & L for galvanised light grade steel conduit of size 40 mm for laying cables in road crossings/drain channel crossings/channels including necessary clamps/other accessories for laying the conduit along the channel, complete all as specified & directed by Engr-in-charge. |
| 19 | Supply & Fix ofXLPE insulated, copper power cable 10 sqmm,3 core unarmoured 650/1100 volts grade conforming toIS 7098 for connection of motors, starter etc with copper lugs of suitable size in cable tray incl. powder coated MS cable tray of suitable size with cover C type for cable dressing including coupler, junction boxes, screws, fastners, etc complete all as specified and as directed by Engr-in-Charge. |
| 20 | S&F of Monoblock horizontal pump set suitable for 415 V ,3 phase system having capacity 12.5 HP, 12 mtrhead, min discharge capacity 36.5 lps with suitable suction and delivery of 100mm x 100mm. The suitable size of base frame, foundation bolts and nuts, coupling and coupling guard including connection of suction and discharge pipe lines, all electrical cable connectionand testing the pump deemed to be incl in the item rate. Any other requirement arising during installation of pumpset and making disturbed surfaces good is all included in the item rate . The pump will be installed at the locationall as specified and directed by Engr-in-Charge.(i) The centrifugal pump set with motor should be guaranteed as per the standard warranty of manufacturer against all defects. Make: Pump: Model KDI-1331+ 12.5HP, 3 Ph monoblock pump of make KBL or equivalent make as specified. |
| 21 | S & F in repair for cast iron sluice valve of 100 mm dia ISI Marked, confIrming to IS14846 both ends flanged with brass spindle, class PN1.6 and necessary new MS nuts, bolts, washer and gasket, and making good disturbed etc complete all as specified and directed by Engr-in-Charge. |
| 22 | S & F in repair of Non Return Valve of 100 mm dia ISI Marked, confIrming to IS5312 both ends flanged with brass spindle, class PN1.6 and necessary new MS nuts, bolts, washer and gasket, and making good disturbed surfaces etc complete all as specified and directed by Engr-in-Charge. |
| 23 | M & L for galvanised medium grade steel water tubing of size 20 mm including fittingslike socket /Union/Tee/diminishing pieces, connectors (connectors shall be inserted , where required or directed), bends, elbow, short pieces, back-nuts, caps, plugs, etc and fixing complete with clips, wall hooks, wooden plugs or laying in trenches, etc also cutting, scewing and waste and for making forged bends on piping as requied, cutting through walls, floors, etc and making good disturbed structures, connecting to old or new position , jointing & testing complete all as specified & directed by Engr-in-charge. |
| 24 | S & F in repairs gun metal gate valves ISI Marked of size 20mm with iron wheel head, screwed both end for iron pipe following bore of pipes complete all as specified & directedMake -Laxmi,Ramco. |
| 25 | M & L for brass suction stainer 100 mm Dia ISI Marked brass made complete all as specified and directed. |
| 26 | M&L CI/DI/MS/GI bends & special confirming to IS-9523:2000 (latest revision) (any type radius and angle ) tappers, any type (straight bend, increasing, decreasing or double socket etc).Tee pieces single branch \"Y\" junction , double branch cross (all socket or socket end spigot ) collar, caps and plugs and connecting pieces one end flanged and other socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth upto 100mmbore complete all as specified and as directed by Engr-in-Charge. |
| 27 | M&L for joint with rubber or fibre board gasket (incl. bolts, nuts, washers and white lead or mineral oil) of size 100mm dia complete all as specified and as directed by Engr-in-Charge. |
| 28 | M & L for GI pipes heavy class of size 100 mm including fittingslike socket /Union/Tee/diminishing pieces, connectors (connectors shall be inserted , where required or directed), bends, elbow, short pieces, back-nuts, caps, plugs,take off saddle clamp etc and fixing complete with clips, wall hooks, wooden plugs or laying in trenches, etc also cutting, scewing and waste and for making forged bends on piping as requied, cutting through walls, floors, etc and making good disturbed structures,connecting to old or new position on walls incl. clamping, jointing & testing complete all as specified & directed by Engr-in-charge. |
| 29 | Supply, Installation, Testing & Commissioning of outdoor type LT Panel 415 V, 3-ph, 50 Hz, CPRI approved, made out of CRCA sheet 3.15 mm thick outdoor pedestal type of size not less than 0.6 x 0.6 x 0.5 m totally enclosed with front & rear opening, hinged doors alongwith suitable locking arrangements, weather and waterproofhaving copper busbars of capacity 100 A for RYB and Neutral with heat proof colour code and mounted on insulators, stickering of switchgears, danger notice plate, including connecting incoming and outgoing cables with 40 x 40 x 5 mm angle legs of length not less than 50 cm fixed to necessary PCC 1:3:6foundation on ground comprising the following:-Incoming(a) MCCB 63A, 4P, 415 V, 50 Hz with rupturing capacity of 25 KA-01 No.Make:L&T cat no. CM91712OOJOOG or equivalent make as specified.(b) Digital MFM , Voltage Measurement-(100-480 V AC (L-L)), Rated Current- 5A, Frequency Measurement- (20-200 Hz), PF & KW Measurement-01 No.Make: L&T, Schneider, C&S electric(c) LED Indicating lamps - 03 Nos. Make: C&S/Neptune/L&T/Vaisnavo(d) CT 50/5 A - set of 03 (Make: AE/Kappa/C&S)Outgoing(a) FASD Starter for 12.5 hp monoblock centrifugal pumpset, 415 V AC, 3 ph, 50 Hz-02 Nos.Make: L&T cat no.SS95890DOAO or equivalent make as specified.(b) MCCB, 32A, 4P with rupturing capacity of18 kA -03 Nos. Make-L&T cat no. CM90518OOFO or equivalent make as specified. (02 outgoing and 01 spare)(Note: Cost includes necessary power and control wiring connections, lugs,required number ofMCB SP 6A,Copper busbars/ other accessories necessary for LT Panel) |
| 30 | M&L for making header 1.5 mtr length with 150 mm dia, min 05 mm thick MS ERW pipe both end closed by welding MS plate, with two inlet and one outlet connections. The size of the inlet & outlet is 100 mm dia. The rate of 150 mm dia MS pipe incl required welding / cutting of MS pipes / plates for making header with branch connections incl the required flanges is deemed to be incl in the item rate. The proper anchoring of header with RCC wall/post with suitable clamps and nuts to withstand vibration caused by the working pressure of water from pumps is also deemed to be incl in the item rate incl making the disturbed surfaces good complete all as specified and as directed by Engr-in-Charge. |
| 31 | S & F of gunmetal female coupling/adaptor 100 mm dia, flanged/ threaded, fixed to outlet of filling pipe, for connecting hose with male coupling, complete all specified and directed by Engr-in-Charge. |
| 32 | M&L for earthing complete with galvanised steel earth plate electrode 600x600x 6mm thick burried in ground (earth pit not less than 2.25 m deep below ground level0with top edge of the plate not less than 1.5 m below normal ground level, connected to GI strip 25 x 4 mm as earthing lead by means of bolts, nuts, check nuts, and washers of GI or steel, GI strip protected by 40 mm bore medium grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade GI, wire mesh charcoal or coke common salt laid in altrnative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC(1:3:6) type C-1, 50 mm thick pre-cast RCC(1:2:4) type B-1 normally mix cover slab reinforced with in 8 mm dia TMT bar 10 cm C/C both ways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft/loose/hard soil and disposal of soil to a distance n.exc 50 m and necessary testing on completion all as shown in electrical plate No 3 MES schedule part-I, incl. mounting GI strip on earth support strip in concrete stretch complete all as specified and as directed. |
| 33 | S & F FRP Waterproof sheet at sides of Galvalume Sheet based shed structure for protection of motors from water jets incl. drilling/screwing/bolting, etc on posts, cutting sheets to required sizes, complete all as directed and specified by Engr-in-Charge. |
| 34 | S & F of pressure gauge 63 mm dial, 0-7 kg/cm2 rating with fittings as per site requirement complete all as specified and directed. |
| 35 | S & F double compression copper stainless steel gland for fixing armoured cable in panel of size 3.5 core 25 sqmm Al cablecomplete all as directed and specified by Engr-in-Charge.. |
