|
| 1 | Excavation in trenches in soft/disintegrated rock, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out complete all as specified and as directed. |
| 2 | M & L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed. |
| 3 | M&L for RCC M-30 Design mix (using 20 mm graded stone aggregate) as in footing, foundation beams, plinth beams, bases of columns etc. complete all as specified and directed. |
| 4 | Use and waste of form work to flat sides of concrete foundation footing, bases of columns raft and raft beams sides and soffits of foundation and plinth beams and similar work vertical or to batter for rough finish surface of concrete complete all as specified and directed. |
| 5 | M&L for RCC M-30 Design Mix (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 6 | Use and waste form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete complete all as specified and directed. |
| 7 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 8 | S&F mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gussets plates, riveting, etc. n exc 10 Kg each brackets, conforming to Fe-290. Gde-E-165 complete all as specified and directed . |
| 9 | M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. |
| 10 | M&L for mild steel TMT CRS bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed. |
| 11 | M&L for mild steel TMT CRS bars 5 mm dia and over in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed. |
| 12 | M&L for 8 to 10 mm wall cladding tiles for wall lining and column cladding Make : Johnson Endura (Santex seriesplus 600 x 600 mm/ Somany Clador 300 x 600 mm or equivalent of make Kajaria/ RAK ceramics/AGI) colour, shade and texture as approved by GE bedded and jointed in neat cement slurry and pointed in colour cement to match with & including rendering 15 mm thick in cement mortar 1:3 finished rough to fix tiles complete all as specified and directed. |
| 13 | S&F in repair three seater garden bench of approximate size 1575 x 600 x 775 mm, minimum weight 60 Kg made out of Mild steel frame and FRP strips of high durability frame painted with powder coated wooden texture paint for a smooth finish which helps avoid corrosion to tolerate maximum seating weight of 350 Kg, 100 % washable and water proof including necessary fixing arrangements to floor complete all as specified and directed. |
| 14 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, leveled and rammed including watering complete all as specified and directed. |
| 15 | M&L for hardcore of broken stone or boulder gauge n.exc. 63 mm deposited, spread & levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed. |
| 16 | M&L For Exterior/ parking floor tiles heavy duty for light traffic, non skid, anti scratch, heavy grip vitreous/ semi vitreous coloured, unique design tiles of size 300 x 300 x 8 to 10 mm thick each as in floor, steps, risers, landing, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.Make:- Duracrete, Durato, RAK, Bell, H&R Johnson |
| 17 | Providing and laying at or near ground level, factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 18 | M & L for preparation of new or previously untreated plastered surfaces or concrete surface exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat priming paint complete all as specified and directed. |
| 19 | Returning filling in including spreading watering and well raming in layer excedding 25 cm each in any type of soil/rock complete all as specified and directed. |
| 20 | Removing excavated material (Soils/Rock) to a distance exceeding 1.5 Km but not exceeding 5 Km and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed. |
| 21 | M&L for writing building No. or figure (Block, Roman, Italic or Indian) with two coats of synthetic enamel paint height not exc. 30 cm over complete all as specified and directed. |
| 22 | Excavating in post holes(or similar holes) each n.exc 0.5 cum in soft/disintegrated rock, getting out, returning, filling in, watering and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed. |
| 23 | M & L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed. |
| 24 | S&F PVC coated chain link fencing MS galvanised, min size 75 x 75 mm mess or cases with 3.5 mm dia mild steel galvanised wire lapped straightning and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 25 | M&L for mild steel work as in posts and struts in fencing or gates, flat iron fillets, angle iron, swan neck including cutting tops to shape, drilling holes, notching for wire etc. conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 26 | S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc. 5 cm and n. exc. 10 cm long with diameter of neck 11 to 15 mm complete all as specified and directed. |
| 27 | M&L Mild steel bars 10mm dia and over as in stiffner to chain link fencing cut to length, bent to shape required including cranking, bending etc. complete all as specified and directed. |
| 28 | M&L for preparation of new of previously untreated steel surface of any description n. exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 29 | M & L for plain cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in coping etc. including necessary formwork complete all as specified and directed. |
| 30 | M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:4 complete all as specified and as directed. |
| 31 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surface/block masonary in cement mortar 1:4 finished even &smooth without using extra cement complete all as specified and directed. |
| 32 | M&L for applying three coats of white wash on walls including preparation of new surface complete all as specified and directed. |
| 33 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 34 | Taking down cement or cement lime plaster on walls/ concrete/roof slab any description including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 35 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surface/ block masonary in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 36 | M&L for applying one coat of alkali resistant primer on plasteredsurfaces of wall and applying two coat of oil bound distemper including preparation of new surfaces complete all as specified and directed. |
