Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of cement concreteand paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.. |
| 2 | Demolition of brick work /stone masonry /PCC block masonry built in cementmortar of any description all as specified and directed.. |
| 3 | Taking down cement plaster of any description hacking for key or raking out joint on old brick work/ stone /concrete surface etc complete all as specified and as directed. |
| 4 | Surface excavation n exc 30 cm deep and average 15 cm in soft/loose soil and getting out complete all as specified and as directed.. |
| 5 | Excavation in trenches n.exc 1.5m wide and not exceeding 1.5 m in depth for foundation etc, orfor shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.. |
| 6 | Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.. |
| 7 | Removing of surplus excavated material exc 50m but n. exc 100m and depositing where directed. at a level n. exc 1.5 m above the starting point etc complete all as specified and as directed.. |
| 8 | Spreading and levelling in well layers not exc 25 cm thick including watering as required etccomplete all as specified and as directed. |
| 9 | Material and labour for hardcore of gauge n exc. 63mm with brokenstone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.complete all as specified and directed.. |
| 10 | Material and labour for Precast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed.. |
| 11 | Material and labour for cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast and fillingof pressed steel chowkatetc complete all as specified and as directed. |
| 12 | Material and labour forcement concrete 1:2:4 type, B1 using (20 mm graded stone aggregates) as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.. |
| 13 | Material and labour for plain cement concrete 1:4:8, type D2, (using 40 mm grade stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and as directed.. |
| 14 | Material and labour for reinforced cement concrete M-25 design mix as in foundations, including rafts, footings, foundation beams; plinth beams bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and directed.. |
| 15 | Material and labour for reinforced cement concrete M-25 (desing mix) with using 20 mm graded stone aggregates as in slab supported on walls, beam and columns in floors, roofs landing balconies canopies etc complete all asspecified and as directed. |
| 16 | Material and labour forproviding reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in Chajja etc complete all as specified and as directed. |
| 17 | M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed. |
| 18 | M&L for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in col, pillars, piers, posts and struts etc complete all as specified and as directed. |
| 19 | Material and labourfor PCC (1:2:4)type B1 (using 20 mm graded crushed stone aggregate) as in coping / benchingetc complete all as specified and as directed.. |
| 20 | Supply only water proofing compound (Liquid) complete all as specified and as directed.. |
| 21 | Material and labour for brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 and complete all as specified and directed.. |
| 22 | Material and labour for brick work with sub class `B\" bricks old sized straight or curved on plan exc 6 M mean radious and built in cement mortar 1:4 etc complete all as specified and as directed.. |
| 23 | Material and labour for brick work with sub class ‘B’ bricks, (locally available best quality) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and as directed.. |
| 24 | Cutting chases, pinning in, in brick wallfor concealed water tubing and making good, in cement mortor 1:3 cutting not exceeding 10cm girth complete all as specified and directed.. |
| 25 | Material and labour for Granite work 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like with and including 15mm bedding in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match the colour of tiles etc complete all as specified and directed.. |
| 26 | Material and labour for mwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.. |
| 27 | Material and labour for mwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.. |
| 28 | Material and labour for mwork to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed.. |
| 29 | Material and labour for mwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) with Rough finished surfaces of concrete (Flat) etc including edges of roof slab etccomplete all as specified and as directed. |
| 30 | Material and labour for mwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.. |
| 31 | Material and labour for2nd class hard wood Plain fillets.square,rectangular ortriangular insection, cleansawn, securedwith nails orbrads area ex6.0 sqm but not exc 13, sqm each etc complete all as specified and as directed. |
| 32 | Supply and fix PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.. |
| 33 | Supply and fix factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tube for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stills and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ scaled to the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement as per drawings and specifications as catered in SSR Part – II 2004 |
| 34 | Supply and fix 2nd class hard wood 35 mm thick Glazed andskeletonshutters, openrebated and preparedto receive glass,gauze, etc. (withoutsash bars),edges offraming plain,chamfered orrounded. fitted withcut and mitred beadsfor securing glass, etc.; sizes of me-mbers of shutters asspecified inSSR PartI, Section 8, clause8.24(a); supplied andfitted to chowkats etc complete all as specified and as directed. |
| 35 | Supply and fix 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 36 | Supply and fix aluminium anodised towerbolt 200 mm long of extruded section etc complete all as specified and as directed. |
| 37 | Supply and fix 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.. |
| 38 | Supply and fix 150mm in size extruded aluminium handles, fabricated type, anodised complete all as specified and directed.. |
| 39 | Supply and fix stainless steelbutt hinges 100 mm long medium weight complete all as directed.. |
| 40 | Supply and fix aluminiumbody door closer hydraulically regulated, universal type suitable for door shutters upto 1M widthof approved make etc complete all as specified and directed. |
| 41 | Supply and fix aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed.. |
| 42 | Supply and fix 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed. |
| 43 | Supply and fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staple etc complete all as secified and as directed. |
| 44 | Material and labour for TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 45 | Allas item No 44 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.. |
| 46 | Material and labour forTMT steelbars 6 to 8 mm dia, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia or with securing clips complete all as specified and directed. |
| 47 | Supply and fix factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed. |
| 48 | Supply and fix factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed. |
| 49 | Supply and fix Powder Coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified and as directed. |
| 50 | Supply and fix Powder Coating (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified complete all as specified etc. complete shall as specified and as directed. |
| 51 | Supply and fixing anodized aluminium sliding glazed window shutter (double leaf glazed shutter and single leaf mosquito proof shutter each in single frame work) without sash bars with anodized aluminium shutter of section 40.00mmx20.00mmx1.10mm thick and window chowkat of section 92.00mmx29.50mmx1.20mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle, tower bolts and locking arrangement etc. and including 4mm thick sheet glass, tinted quality on panel and stainless steel wirecloth or aluminium anodized wire cloth for mosquito proofing, 0.45mm nominal dia and average width of aperture 1.40mm fixed with aluminium screws and tacks and making good to disturbed surfaces complete all as specified and as directed. |
| 52 | Anodized aluminium powder coated push pull type fully glazed door shutter (single leaf / double leaf) having top rail of section 85.00mmx44.45mmx2.00mm, bottom rail of section 85.00mmx44.45mmx2.00mm thick, door verticals of section 44.45mmx44.45mmx2.00mm thick and lock rail of section 85.00mmx44.45mmx2.00mm thick with aluminium anodized chowkats of section 63.50mmx33.10mmx2.50mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle and locking arrangement etc. 5.5 mm thick float glass tinted quality on top/bottom panel complete all as specified and as directed.. |
| 53 | Material and labour for framed work as in grills, grating etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed balusters walks ways, railing framed work of water tanks and similar work etc complete all as specified and as directed. |
| 54 | Material and labour for applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017, 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/Sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer\"s instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed.. complete all as directed.. |
| 55 | Material and labour for water proofing treatment to RCC roof slab, including parapet comprising with the followingof treatment/specification from bottom to top:-(i) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 mixed with water ptoofing compound @ 3% of weight of cement or as per manufactures instructionsand surface finished even and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. (ii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986.(iii) APP based polymeric membrane 3mm thick (minimum),weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall beapplied over bituminous primer as specified above overby torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction.(iv) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm.Note: Water proofing compount will be measured & paint seperatly. |
| 56 | Supply and fix 18mm thick Block boards, grade 1 quality, exterior grade, commercial type, Water proof, termite proof, fixed with screws to timber frame-work as in wall panelling / cub board shutter, Kitchen shelves and modular kitchen shutter, shelves, drawers etc over 0.90 mm thick decorative laminate type 1, of surface finish (both side of shutter), colour and pattern as approved, fixed with approved adhesive as per maker\"s instructions etc complete all as specified and as directed. |
| 57 | Material and labour for 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice laminations and other side blenching white lamination, fixed with screws to aluminium frame work complete all as specified and as directed. |
| 58 | Material and labour for 100 mm thick plain cement concrete (1:4:8)type D2 (using 40 mm graded crushed stone aggregate) as insub base of tiles/floor of hard standing/path etc complete all as specified and directed.. |
| 59 | Material and labour for 25mm thick PCC 1:2:4 type B-0(using 12.5mm graded stone aggregate) as in sub base for path/paving/hard standing/floor etc. complete all as specified and as directed.. |
| 60 | Material and labour for 75 mm thick cement concrete 1:4:8 type D- 2(using 40mm graded stone aggregate) asin sub base of flooing etc complete all as specified and as directed. |
| 61 | Material and labour for 75mm thick PCC 1:3:6, type C1 (using 20mm graded stone aggregate) as in plinth protection, etc finished the surface even and smoothwithout using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic jointfilling at every 3m length and at corners complete all as specified and as directed.. |
| 62 | Material and labour foracid resistant tiles 15mm thickvitreousceramic, unglazed, set,jointed and pointed inchemicalresistant mortar, resin type, inflooretc complete all as specified and as directed. |
| 63 | All as per item no 62 above, but as vertical surface etc comlete all as specified and as directed. |
| 64 | Material and labour for proving 40 mm thick bitumen mastic wearing courses with industrial bitumen of grade 85/25 confirming to IS:702-1988 and amended from time to time, prepared by using mastic copper and laidto required level and slope, including providing anitiskid surface with bitumen precoated fine grained hard stone chipping of approved size at aproximate spacing of 20 cmcentre to centre in both directions pressed into surface protruding 1 mm to 4 mm ove mastic surface (Considering bitumen using 10.20% as per NORTH specification) including preparatin of surface andremoval of debries / dirt etc complete all as specified and as directed. |
| 65 | Material and labour for glazed vitrifiedtiles (GVT) light shade 8 to 9mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchin floor including15 mm thick screed bed or bedding layer for laying floor finishes in CM 1:4etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.. |
| 66 | Material and labour forglazed vitrifiedtiles (GVT) light shade8 to 09 mm thickarea of each tile notexceeding 0.36 sqm,in skriting dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.. |
| 67 | Material and labour for glazed coloured ceramic tiles of size 300X450X7mm thick on vertical surfaces set, jointed and pointed in net cement slurryand pointed in white cement mixed with colour pigments to match the existing surface over 10mm thick renderingin CM 1:4 complete all as specified and directed.. |
| 68 | Material and labour for Glazed ceramic tiles coloured 300mmx 450mm , 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified andand as directed. |
| 69 | Material and labour for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchetc complete all as specified and as directed. |
| 70 | All as per item no 46 above, but as vertical surface etc comlete all as specified and as directed. |
| 71 | Material and labour for machine cut kota stone slab flooring 20-25 mm thick over cement screed base 20 mm in CM 1:6,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 72 | Material and labour for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with including 10mm thick rendering in CM 1:3 etc set and jointed in neat cement slurry complete all as specified and as directed. |
| 73 | Material and labour forNon - skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) laid in floors area of each tile exc. 0.11 sqm but n.exc 0.18 sqm, in floors etc. with and incl 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as directed.. |
| 74 | Material and labour for exterior grade, coloured glossyfinish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thickset, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles over etc complete all as specified and directed.. |
| 75 | Material and labour for screed bed or bedding layer of mortar 15mm thick in CM 1:6for laying floor finishescomplete all as specified and as directed.. |
| 76 | Material and labour for screed bed or bedding layer of mortar 20 mm thick in CM 1:6for laying floor finishescomplete all as specified and as directed.. |
| 77 | Material and labour for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed. |
| 78 | Material and labour for rendering for ceiling 5 mm thick in CM 1:3 on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed. |
| 79 | Material and labourfor 10 mm thick rendering in CM 1:6 on brick/ concrete surfaces and finishing the surfaces even and fair etc complete all as directed.. |
| 80 | Material and labour for 10 mm cement plastering in CM (1:3) as in horizontal and vertical surface of brick work or concrete surface mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed. Notes : WPC shall be measured and paid seperately |
| 81 | Material and labour for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thickmixed with liquid water proofing compoundas per manufacture\"s instructions finished even and smooth without using extra cement complete all as specified and as directed.. Note : liquid Water proofing compoundwill be measured and paid separately as \"Supply only\". |
| 82 | Material and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 83 | Materials and labour for preparation of newly plastered surface of wall and applying two coats of acrylic distemper over a coat of primer complete all as specified and as directed.. |
| 84 | Material and labour forpreparation of new plastered surface of walls and applying two coats of cement based paintover one coat of concrete primer/ alkali resitant primerall as specified and directed.. |
| 85 | Material and labour fornewly plastered surfaces of wallsapplying one coat of alkali resistant primer over a coat of birla white cement putty 1 mm thick ,sanding the surfaces till smooth finish is obtained and finally applying two coats of acrylic distemper etc complete all as directed.. |
| 86 | Material and labour for preparing newely plastered surface of ceiling and applying three coat of white wash etc complete all as specified and as directed. |
| 87 | Material and labour forpreparing Old plastered suface of walls and applying two coats acrylic distemper , white or tintedetc complete all as specified and as directed. |
| 88 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surface |
| 89 | Supply and fix 4mm thick sheet glass ofordinary quality and glazing with oil putty or wooden beading to wooden frame or steel framein squares n exc 0.50 sqm in each pane complete all as specified and as directed. |
| 90 | Supply and fix ordinary quality Sheet Glass 5.50mm thick and glazing in rectangular/square exc 0.5 sq. m in each pane complete all as specified and directed.. |
| 91 | Material and labour for preparation of new steel surfacesexc 10 cm width/girth and applying two coats of synthethic enamel paint over a coat of primer etc complete all as specified and as directed. |
| 92 | Material and labourfor preparation of New woodensurfaces of any description exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed.. |
| 93 | Supply and fix GI tubing 15mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.. |
| 94 | Supply and fix GI tubing 20 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.. |
| 95 | Supply and fix PVC float valve assembly including assessories with float valve 25mm diacomplete all as specified and directed. |
| 96 | Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified and directed. |
| 97 | Supply and fix 15mm bore chromium plated swivel type shower rose with arms all as specified and directed.. |
| 98 | Supply and fixing rotational moulded polyethylene water storage tank 1000 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.. |
| 99 | Supply and fix angular stop valves 15 mm dia cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed.. |
| 100 | Supply and fixing vitreous china wash down water closet (EWC) pan (pedestal pattern) size (540 X 365X 390 MM )white, including seat cover, closed pattern with flat bottom and cover with chromium plated hinging device complete all as specified and as directed.. |
| 101 | Supply and fixing PVC low level flushing cistern, pastel coloured, 10 ltrs capacity, valveless, syphonic action type including all fittings and flush pipe, PVC connection pipe complete all as specified and as directed.. |
| 102 | Supply and fix vitreous china WHB white flat back size 550x400mm including Supply and fix angle iron brackets,CP waste coupling, 32mm dia and PVC waste pipe 32mm dia and PVC connection 450mm long high pressure complete all as specified & directed.. |
| 103 | Supply and fix Vitreous China full size pedestal for wash hand basin complete all as specified and directed. . |
| 104 | Supply and fix chromium plated Health faucet brass CP for 15 mm bore pipe with chromium plated pipe of 1 Mtr length complete all as specified and directed. |
| 105 | Supply and fix fancy type long body bib taps, chromium plated cast copper alloy 15mm bore with crutch or butter fly handle, screwed down, & fixed complete all as specified and directed.. |
| 106 | Supply and fixPVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.. |
| 107 | Supply and fixbrass chromium platedWHBmixer for mixing Hot & Cold water high pressure, screwed down for 15mm bore iron pipe fixed in repairall as specified and directed.. |
| 108 | Supply and fix25mm dia harrison rails, stainless steel, CP Curtain rod with fixing brackets, dooms, stops, rollers etc. complete all as specified & directed.. |
| 109 | Supply and fix Tubular Towel Rail of 20mm dia of 60cm in length, D shaped, with brass chromium platedbrackets all as specified and directed..including brackets complete all as specified and directed.. |
| 110 | Supply and fix 75 mm dia PVC ( SWR) floor trap with dome type grating including jointing with solvant etc complete all as specified and directed.. |
| 111 | Supply and fixPVC (SWR) pipes 75 mm bore single socketed, in any length with adhesivejoint fixed to wall/floor including ms clamps and necessary fitting complete all as specified and directed. |
| 112 | Supply and fix Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as specified and directed.. |
| 113 | Supply and fix mild steel pre paintedhat pegs solid body set of six Noscomplete all as specified and as directed.. |
| 114 | Supply and fix PTMTPVC grating dome type of 100 mm dia.complete all as specified and directed.. |
| 115 | Supply and fix PVC (SWR) vent cowl for75 mmbore pipe complete as specified complete all as specified. |
| 116 | PVC (SWR) bends/shoe of any radius for 75 mm bore complete as specified complete all as specified. |
| 117 | Supply and fix bevelled edge looking mirror 5 mm thick of size 600x450 selected quality glass mounted6mm thick AC building board or commercial plywood andfixed to wooden plug with chromium plated screws and cup washer all as specified and directed.. |
| 118 | Supply and fix sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipeincluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mmcomplete all as specified & directed.. |
| 119 | Material and labour for cement concrete bed to drain pipes including packing under and haunching againstthe sides of pipe after they are laid & tested for 150 mm bore of pipe withcement concrete 1:3:6 type C-2 using 40mm graded stone aggregatecomplete all as specified and directed.. |
| 120 | Supply and fix SGSW pipes 150 mm bore single socketed, in any lengthwith rubber ring joints, laid in trenches or in floorsand jointed complete all as specified and directed.. |
| 121 | Cutting into existing manholes for connecting 100 mm new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required |
| 122 | Material and labour for point wiring with 1.5 sqmm, single core, PVC insulated and PVC unsheathedFR-LSH cable, 1100 volts grade IS-694marked, with multistranded copper conductors and earthcontinuity wire with 1.5 Sqmm copper conductor cable (including connecting to earth dolly)laid/fixed with and including PVC rigid conduit on walls/ceiling ( concealed),with MS/PVC terminal boxes fixed flush with wall surface with 3mm thick masonite laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulators etc. including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly for one light or fan point controlled by one 5 Amp switch one way complete all as specified and as directed.. |
| 123 | All as per item serial No 122 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches |
| 124 | All as per item serial No 122 here-in-before but One socket outlet 3 pin 6 Amp on independent board complete all as specified and as directed.. |
| 125 | All as per item serial No 122 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and as directed.. |
| 126 | Supply and fixswitch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and as directed.. |
| 127 | Supply and fix modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed.. |
| 128 | Supply and fix modular switch 1 way 16 amp, 1 module complete all as specified and as directed.. |
| 129 | Supply and fix modular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed.. |
| 130 | Supply and fixceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and as directed.. |
| 131 | Supply and fix switch piano, flush type single pole one way 5 Amps 230 volt complete all as directed.. |
| 132 | Supply and fix socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as directed... |
| 133 | Supply and fix switch socket combination outlet 5 pin, 2-in-1, 5 Amp flush type complete all as directed.. |
| 134 | Supply and fix switch socket combination multipurpose, 2 in 1, 6 pin, 5 & 15 Amp flush type complete all as directed.. . |
| 135 | Supply and fix stepped type electronic fan regulator, two module size, flush type complete all as specified and directed.. |
| 136 | Supply and fixlamp holder ,PVC/Polycarbonate type with back plate suitablefor batten fittings complete all as specified and as directed.. |
| 137 | Supply and fixingLED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.. |
| 138 | Supply and fixingLED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.. |
| 139 | Supply and fixLED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.. |
| 140 | Supply and fixLED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and as directed.. |
| 141 | Material and labour forGI bracket made out of 40 mm bore light grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape all as directed., length of GI Pipe shall not be less than 2.0 metre for fixing of light fittingscomplete all as specified and as directed.. |
| 142 | Supply and fix modular white cover plate with frame, 4 module complete all as specified and as directed.. |
| 143 | Supply and fix modular white cover plate with frame, 6 module complete all as specified and as directed.. |
| 144 | Supply and fix modular white cover plate with frame, 8 module complete all as specified and as directed.. |
| 145 | Supply and fix metal flush box 4 module for modular switches complete all as specified and as directed.. |
| 146 | Supply and fix metal flush box 6 module for modular switches complete all as specified and as directed.. |
| 147 | Supply and fix metal flush box 8 module for modular switches complete all as specified and as directed.. |
| 148 | Supply and fix MCB DB of sheet metal enclosure double door SPN 8 way IP-43 with 200 A rated bus barand grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed.. |
| 149 | Supply and fix MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed.. |
| 150 | Supply and fixMCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed.. |
| 151 | Supply and fixfactory made, sheet steel distribution boards, TPN, 4 Way,double door,IP-43with provision for FP MCB as incomer and SP MCBs as outgoing complete and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed.. |
| 152 | Supply and fix MCB Tripple pole & neutral 40 to 100 Amps in accordance with IS/IEC 60898-1, 415 V, 50 Hz,10 kA,C-series rupturing capacity providing in DB complete all as specified and as directed.. |
| 153 | Supply and fix Sheet metal earth plug, socket, SPN with single pole MCB 6 to 32 Amps fixed in complete all as specified and as directed.. |
| 154 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.. |
| 155 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed.. |
| 156 | Material and labour for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated and unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dia non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSHPVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing oncomplete all as specified and directed.. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 157 | Material and labour forwiring with 2 runs of 6 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith two run of 6 sqmm single core FR-LSHPVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completioncomplete all as specified and directed.. Note: 2 run of 6 Sqmm cable and 1 run of 6 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 158 | Material and labour for plate earthing completewith galvanizedmild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than2.25 m deep below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth lead wire 4 mm dia or 8 SWG bolted (with GI nuts, bolts & check nuts) and earth plate electrodeat one end and connected to main switch board/ DBs etc. at the other, earth strip encased(protected) in and including 15 mm boreGIpipe medium gradewith all fittings from top of electrode to main switch board/ DBs etc fixed with and including 25 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-2 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work complete all as specified and shown in electrical plate No 3 of SSR Pt-I. |
| 159 | Material and labour for earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm burieddirectly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etcRCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate)including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 complete all as specified and as directed.. |
| 160 | Supply and fix steel tubes medium grade galvanised 25 mm bore with all fittings and fixed complete to walls and ceilings and laid in floors complete all as directed.. |
| 161 | Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 25mm bore complete all as specified and directed. |
| 162 | Material and labour for Cutting existing steel tubing of 40mm for alterations or additions complete all as specified and directed. |
| 163 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core complete all as specified and directed. |
| 164 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35.0 sq mm 3.5 core complete all as specified and directed. |
| 165 | Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.. |
| 166 | Material and labour for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified |
| 167 | Material and labour for GI pipe light grade 40mm bore dia with all fittings to be laid in trenches or in floors,including taking down rusted one complete all as speciffied and as directed.. |
| 168 | Material and labour for Manual boring under roads/hard standingby reqd T&P without disturbing the top surface of the road for throughing the cable in GI Pipe of n exc 40 mm dia all as specified and directed.. |
| 169 | Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 V complete all as directed.. |
| 170 | Supply and fix MCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with 250 Amps rated copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
