|
| 1 | Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 2 | Material and labour for sand cushoning laid over sub base for fixing inter locking tiles complete all as specified and directed. |
| 3 | Material and labour for Machine pressed precast conctete interlocking glossy/ lacquer finish paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80mm thicknessincluding 2mm thickrubber mould glossy/ lacquer finish paver block of GradeM-35 and over sand cushion complete all as specified and directed. ( Note- Sand will be measured and paid separately) |
| 4 | Material and labour for chequered tiles 25cmx25cmx22mm thick, set, jointed and pointed in near cement slurry in floors with grey cement andpigment and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed. |
| 5 | Material and labour forFactory made precast cement concrete 1:2:4 type B-1 (using 20 mm and below stone aggregate ) in kerb stone factory made as approved by EIC with plaine fair faces including champhering, weathering etc complete with joint to match in CM 1:6 complete all as specified and directed. |
| 6 | Material and labour for Preparation of new kerb stone or plastered surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer. complete all as specified and directed. |
| 7 | Material and labour for 75 mm thick plain Cement concrete type B1, 1:2:4 (20mm grade aggregate)as in paving area etc and finished even and fair finishescomplete all as specified and directed. |
| 8 | Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles and removing rubbish from the site complete all as specified and directed. |
| 9 | Material and labour for Brickwork with flyash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified anddirected. |
| 10 | Taking down cement Plaster , any description, on brick walls or stone walls,etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 11 | Material and labour for Cement plaster 15mm thick onbrick work or concrete surface in CM (1:4) including rendering to be finished even and smooth with out using extra cement complete all as specified and directed. |
| 12 | Material and labour for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed. |
| 13 | Material and labour for preparation of old plastered or un plastered surfaces and applying two coats of cement base paint complete all as specified and directed. |
| 14 | Material and labour for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface chanels including throatingand use and waste of form work complete all as specified and directed. |
| 15 | Material and labour for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed. |
| 16 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid bedded and ponted in any mortar complete all as specified and directed. |
| 17 | Material and labour for 18-20 mm thick machine cut,Granite stone slab (of any type)(table rubbed and polished) in steps,jambs, pillars, windows, cills, cooking plateforms and like in cement mortar 1:4 bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting andpolishing types and making mould on edges &including 15 mm thick screed bed in CM (1:6) complete all as specified and directed. |
| 18 | Material and labour forGranite (of any type)15-18 mm thickwork (table rubbed and polished) for wall lining (veneering to wall) including 12mm thick in cement mortar (1:3) of rendering/ backing coat and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.complete all as specified and as directed |
| 19 | Dismantling floor hearth or wall tiling including cement mortarbedding and rubbish off the premises complete all as specified and directed. |
| 20 | M & L for digital ceramic wall cladding tiles of size 450mm x300mm / 450mm x150mm of 7-8mm thick or 600mm x148mm x10mm thick of as approved by EIC size and colourin vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat in CM 1:4all as per manufacturer instruction and including necessary scaffoldings upto G+4 complete all as specified and as directed |
| 21 | Demolition of RCCof any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 22 | Material and labour forFactory made Precastcement concreteType B1, 1:2:4 (using 20mm aggregate), as in cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facesin CM 1:4 complete all as specified and directed. |
| 23 | Material and labour for TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 24 | All as per item No. 23 abovebut 8mm dia complete all as specified and directed. |
| 25 | Dismantling of plain or corrugated steel sheeting , any gauge and thickness in roof covering including Nainital or similar pattern roof covering, complete all as specified and directed. |
| 26 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc including from posts embedded in PCC of any size and thickness complete all as specified and directed. |
| 27 | Material and labour for cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate as in foundation, filling & mass concrete etc complete posts and struts orfencing posts and including finishing the surface even and smooth all as specified anddirected by Engineer-in-charge. |
| 28 | Supply and fix for mildsteel rolled section as fencing posts,vertical posts etc (beam,angle,tee section channel or flat section )and simmilar work including neccesary cutting drilling. complete all as specified and directed. |
| 29 | Supply and Fix for Steel work in tabular/hallow sections of trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and directed. |
| 30 | Supply and fix formild steelframed work as in doors or gates of angle or other section with gusset plates , rails braces , wind ties drilled for fixing of steel sheeting& incl.& hinges complete incl. mild steel plain black sheet in wallcladding, cut to size, holes punched,incl. round headed screws or rivets with plain 40mm lap of Fe 290 (gde E-165)complete all as specified and directed. |
| 31 | Supply and fix for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.50mm thick of any colour having tensil strength of 550 Mpa, as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 32 | Material and labour for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of primer exposed to view surfaces complete all as specified and as directed. |
| 33 | Supply and fix in repairs to 4 to 5 mm thickM S Galvanised Chain link fencing with PVC coating minimum thickness not less than 1mm fixed toposts and including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.complete all as specified and directed. |
| 34 | S & F Steel rolling shutter ( thickness of lath 1.25mm thick) without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete push pull or manual type. |
| 35 | S & F Steel rolling shutter ( thickness of lath 1.25mm thick) without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete gear operated type with bevel gear box and crank handle. |
| 36 | Routine maintenance of rolling shutter of following sizes the maintenance including the following all as specified and directed.(a) Taking down hood covers for carrying out routine maintenance and re -fixing.(b) Dismantling the MS and CI works of any description such as sheets, shafts, cost iron wheels lath etc and taking down helical springs, rollers and other accessories etc.(c)Replacementofunserviceable accessories such as shafts, helical springs, rollers lath sheets, cast iron wheels etc.(d) Replacement of the unserviceable accessories such as shaft helical spring, rollers, MS lath sheets hood covers, cast iron wheels including drilling, welding etc complete.(e) Cleaning, oiling, greasing etc complete of all movable parts all as required at site( Note- The parts and accessories to be replaced shall be measured and paid separately )\"Note:- Any defects noticed during the period of contract the same shall be rectified by the contractor with out any cost. |
| 37 | (A) Area of shutter n.exc 5.00 sqm maximum size 1.80mx2.40m |
| 38 | (B) Area of shutter exc 5.00 sqm but n.exc 10.00 sqm |
| 39 | (C) Area of shutter exc 10.00 sqm but n.exc 20.00 sqm |
| 40 | Supply only mild steel lock plate 150mm width 3.15mm thickness reinforced with MS angle of 35x35x5 mm at bottom including pulling handle sliding bolt etc complete all as specified and directed. |
| 41 | Supply only mild steel gear box including gear wheels of rolling shutter machine cut with MS shaft 25mm bore heavy grade complete all as specified and directed by EIC |
| 42 | Supply only worn out top gear wheel of high grade cast iron or mild steel complete all as specified and directed by EIC |
| 43 | supply only MS work as angle channel tees section as in top/bottom sliding channel rail and stopper frame of door & guides including necessary welding, rivetting nut bolts Fe-290(gdeE-165) all as specified and directed. |
| 44 | Supply only new helical springs of size n.exc 50 Cm long as required for rolling shutters etc all as specified and directed. |
| 45 | Supply only new helical springs of size exc 50 Cm long as required for rolling shutters etc all as specified and directed. |
| 46 | Supply only MS shaft, 40mm bore heavy grade for bearing, spring etc in position etc all as specified and directed. Fe-290(Gde E-165) |
| 47 | Supply only MS lath 1.25 mm thick for rolling shutter of size and description all as specified and directed. |
| 48 | Supply only MS plain sheet 1mm thick as in hood cover for rolling shutters of size and pattern as approved all as specified and directed. |
| 49 | M&L for preparation of new steel surfaces and applying two coat of aluminiumpaint over a coat of aluminium red oxide etc complete all as specified nd directed. |
| 50 | M&L for preparation of old steel surfaces and applying one coat of aluminiumpaintetc complete all as specified nd directed. |
| 51 | M&L for preparation of old steel surfaces and applying one coat of synthetic enamel paint etc complete all as specified nd directed. |
| 52 | Removal of building materials/debris from 1.5mtrto a distance of out side of 5.0 KM etc complete all as specified and directed. |
