|
| 1 | Demolition of concrete and pavings n.exc 15 cm thickness (below or above ground level) |
| 2 | M&L, PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, fitting and mass concrete |
| 3 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PUcoated mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. |
| 4 | M&L chequered PU coated tiles 30cmx 30cmx, set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 15mm thick screed in cement mortar 1:6 |
| 5 | M&L for providing cement concrete type B-1 1:2:4 (20mm graded aggregate) as in copings Complete all as specified and directed by Engineer-in-Charge. |
| 6 | Dismantling wrought iron or mild steel work of any description such as guard bars, grills etc. |
| 7 | S&Fsteel work as in posts and struts , truss, flats in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 8 | Excavating in post holes each n exc 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceedings 25cm watering and removing surplus soil to distance n exc 50 m and making good surfac in soft/loose soils |
| 9 | Dismentling asbestos cement corrugated orsemi corrugated sheets in roof fixed with L hook or cranked bolt |
| 10 | S&F pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge |
| 11 | Dismantling fencing wiremesh, any type Complete all as specified and directed by Engineer-in-Charge. |
| 12 | S&F high quality zinc coated GI Chain linkfencingof required width in mesh size 50x50 mm made of GI wire dia not less than 3mm and fix with column with nut or bolts and strengtheing with 10mm TMT bars, conforing to standard grade steel complete all as specified and directed. NOTE:- (i) Payment of TMT bar shall be made in seperate items in this Schedule.(ii) The Engr-in-Charge along with rep of contractor shall verify the weight mesh and submit the copy along with photographic eveidence along with RAR and Purchase Voucher. (iii) The quoted rate shall be inclusive of Nut bolt required. |
| 13 | S&F 3mm thick fibre glass reinforced translucent plain sheeting withside lap fixed with srew. |
| 14 | M&L for two coats synthetic enamelled paint over one coat of red oxide primer incl preparation of new surface of steel of any description any width or girth complete all as specifed and as directed by Engr-in-Charge. |
| 15 | S&F mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Complete all as specified and directed by Engineer-in-Charge. |
| 16 | Schedule of Credit |
