Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | PHASE - I(a) Conducting primary studies and detailed soil exploring as per IS 1892:2021 and IS 16700:2023 for G+1 storis building at Furniture yard under ABHM Complex for overall layout of structure, geology, topography, etc. Minimum requirement given for geotechnical exploration by IS 16700:2023 i.e bore hole shall be spaced at maximum 10mtr within building footprint, minimum 01 Bore Hole and depth of investigation shall be 1.5 times estimated/recommended smaller width of foundation subject todept of up to10 mtr . All tests as specified in above IS code including recommendation for footing shall be provided in five copies. The report shall be vetted by a govt approve lab. (b)Based onthe soil condition a details structural drawing include architectural drg(5 copies with soft copy duly vetted by a govt college) as per line plan provided by the engr in charge before execution of the work shall be provided as per direction by engr in charge. |
| 2 | PHASE - IIB&R PORTION:Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 3 | Excavation in trenches not exc 1.5 mtr wide & not exc 1.5 mtr in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed. |
| 4 | M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, pavings, filling and mass concrete complete all as specified and directed. |
| 5 | M&L for reinforced cement concrete (nominal mix) Type A1 of1:1.5:3 (20mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concretandthe like complete all as specified and directed. |
| 6 | M&L for reinforced cement concrete (nominal mix)Type A1of1:1.5:3 (20mm graded crushed stone aggregate) as inColumns, pillars, piers, posts and struts complete all as specified and directed. |
| 7 | M&L for reinforced cement concrete (nominal mix)Type A1 of1:1.5:3 (20mm graded crushed stone aggregate) as in roof or floor beams, cantilevers, bressumm ers, lintels over 1.5m span complete all as specified and directed. |
| 8 | M&L for reinforced cement concrete (nominal mix)Type A1 of1:1.5:3 (20mm graded crushed stone aggregate) as in Chajja/facia etc complete all as specified and directed. |
| 9 | M&L for reinforced cement concrete (nominal mix)Type A1 of1:1.5:3 (20mm graded crushed stone aggregate) as Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings complete all as specefied and directed |
| 10 | M&L for reinforced cement concrete (nominal mix)Type A1 of1:1.5:3 (20mm graded crushed stone aggregate)Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 11 | Use & Waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces complete all as specified and directed. |
| 12 | Use & Waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces complete all as specified and directed. |
| 13 | Use & Waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished surfaces complete all as specified and directed. |
| 14 | Use & Waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces complete all as specified and directed. |
| 15 | Use & Waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batterroughfinishedsurfaces complete all as specified and directed. |
| 16 | Use & Waste of formwork to Formwork to flat staircases with sloping or stepped soffits including risers and stringers rough finished surfaces complete all as specified and directed. |
| 17 | Use & Waste of formwork to Chajjas, chullah hoods, troughs and similar items including edges rough finished surfaces complete all as specified and directed. |
| 18 | M&L for TMTbars 10 mm dia and over, cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with mild steelwire (annealed) not less than 0.9 mm dia or securing with clips,complete all as specified and directed. |
| 19 | M&L for TMTbars 6 mm to 8 mm dia, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hookingends and binding with mild steelwire (annealed) not less than 0.9 mm dia or securing with clips,complete all as specified and directed. |
| 20 | M&L for TMTbars 5 mm dia and over upto and including 10 mm dia, as in stirrups, spacers and binders, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hookingends and binding with mild steelwire (annealed) not less than 0.9 mm dia or securing with clips,complete all as specified and directed. |
| 21 | M&L forbrick work withsub class\"B\" bricks , usingold sizebricks, straight or curvedon plan exc 6 m meanradius built in cement mortar1:6 complete all as specified and directed. |
| 22 | M&L for brick work with sub class \"B\" bricks using old size bricks, straight or curved on plan to any radius, built in CM 1:4 as in half brick thick wall complete all as specified and directed. |
| 23 | M&L for 40 mm thick PCC 1:2:4 type B-0 as in damp proof course to horizontal or vertical surfaces including necessary formwork over 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m. complete all as specified and directed. |
| 24 | M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metreofsurfacearea complete all as specified and directed. |
| 25 | M&L for treating the backfill in contact with foundation at the rate of 7.5 litre of emulsion per square metre of vertical surface (area of the sub structure in contact with backfill to be measured) complete all as specified and directed. |
| 26 | M&L for Treating the top surface of filled earth at floor at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed. |
| 27 | M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. |
| 28 | M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed. |
| 29 | M&L for hardcore of broken stones gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface over compacted earth complete all as specified and directed. |
| 30 | M&L for 100 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or sub floors or path finishing the surfaces even and rough to receive the topping layer complete all as specified and directed. |
| 31 | M&L for 40 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in leveling layer and finishing the top surface even and rough to receive the topping layer ortiling complete all as specified and directed. |
| 32 | M&L for Udaipur green marble work 16 to 18mm thick (table rubbed and polished) in floors or the like including including 20mm thick screed bed in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shadeincluding rounded edges with shade of Udaipur green complete all as specified and directed. |
| 33 | M&L for Udaipur green marble work 16 to 18mm thick (table rubbed and polished) in steps, riser/skirting, jambs, pillars, window cills, floor, and likeand pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shadeincluding rounded edges with shade of Udaipur green complete all as specified and directed. |
| 34 | Rounding to edges of stone slabs on edge such as in steps,coocking plateform and other similar situations complete all as specified and directed. |
| 35 | M&L for vetrified tiles of size 1200x 600mm and 10mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed. |
| 36 | All as per item No 35.00 above but , as in skirting laid on 10 mm thick cement plaster in CM (1:4), set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles complete all as specified and directed. |
| 37 | M&L for super gloss decarative coloured (light and dark colour) walls tiles of size 600x1200x10mm mm thick, for works on vertical surfaces such as skirting/dados of 1st quality , set and jointed in neat cement slurry and pointed in coloured cement to match including rendering 10mm thick on fair faces or other than fair faces of brick work in cement mortar 1:4, finished even and fair as in backing layer complete all as specified and directed by Engr in charge. |
| 38 | M&L for ready mix plaster 15 mm thickon conc/brick surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 39 | M&L for preparation of brick or concrete surface cleanandfreeofdust,oil,paint,looseparticles, demolding agents, organic products etc and applying 15mm thick exter surface treatment as in two layers (10mm base layers and 5mm final layer) as under :-(a) Base coat (10mm thick) : Apply in one or more coats to achieve average 10mm thick of water vapour permeable mortar, UNOFIN CLASSIC basecoat Render or equivalent brand of Make Sika, Fosroc for weather resistant & high performance façades with CSIV compressive strength, Flexural Strength ≥ 2.5 N/mm2 and water vapour permeability ≤μ15 as per EN 998-1 and finished even & rough marks to anchore with final layer. It should be includes the reinforcement of weaker points/areas (change in the substrate material, slabs, pillars, roller blind boxes, around the openings/windows, doors, etc.), with fibreglass mesh to avoid cracks as per manufacturer’s recommendations or as per direction of Engr in Charge (b)Final layer (5mm thick)Finishing with the rainwater resistant and water vapour permeable rendering mortar with colour as approved by Engr in chage, UNOFIN PRIME COARSE Render or equivalent brand of Make Sika, Fosroc, applied in two or more coats to achieve 5mm thick for rainproof/weather resistant & decorative facades with a CSII Compressive Strength class, Flexural Strength ≥ 2.5 N/mm2, resistance to water absorption as W2 (C ≤ 0.2 Kg/m2. min0.5), water vapour permeability ≤μ15 as per EN 998-1 all as per manufacturer\"s recommendations and finished even and smooth all as per specification and directionNote : 1.Size and specification of fiberglass mess shall be as per manufacturer\"s recommendations 2.Contractor shall be provide authorised applicatore and no exter cost shall be provided in this account |
| 40 | M&L for 5mm thick ready mix plaster as on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 41 | S&F PVC corner bead of size 36x36mm with fiberglass mesh of size 100x100mm consist of perforated PVC corner bead and reinforcing fiberglass mesh shall be provide for all 90 °C angle constructions, including exterior/interior plastering, wall corner, arch, window, door and EIFS including all fixing material such as screw, gum or similarcomplete all as specified and directed. |
| 42 | M&L for preparation of new plastered wall surfacesand applying two coats of distemper oil emulsion, white or tinted over one coat of primer including 2mm thick wall care putty complete all as specified and directed.Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days days from bid start date of the said work.(c) The contractor shall provide application, testing and certification of finishes by paint manufacturing firms/their authorised applicators.(d) Cost of above mentioned shall also included in quoted rates |
| 43 | M&L for preparation of new ceiling surfaces and applyingtwo of distemper oil emulsion, white or tinted over a coat of primer paint over 1mm thick puttycomplete all as specified and directed.Note : (a) All work shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufactures shall have valid authorisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days days from bid start date of the said work.(c) The contractor shall provide application, testing and certification of finishes by paint manufacturing firms/their authorised applicators.(d) Cost of above mentioned shall also included in quoted rates. |
| 44 | M&L for 75 mm thick cementconcrete1:3:6 type C-2 (using40 mm graded crushed stone aggregate) as in plinth protection laid to slope of 1 in 12 complete all as specified and directed. |
| 45 | S&F PVC (SWR) pipes single socketed, 110 mm bore in any length with rubber ring joints, fixed to walls, ceiling or floor etc complete all as specified and directed. |
| 46 | S&F PVC (SWR) bends, tee, Y babd, L band, cowl, legs, 45 band, shoes or smilar type joint fixing of any shape of 75 mm bore complete all as specified and directed. |
| 47 | S&F PVC (SWR) bends, tee, Y babd, L band, cowl, legs, 45 band, shoes or smilar type joint fixing of any shape of 110 mm bore complete all as specified and directed. |
| 48 | M & L for:(a) Cleaning the roof surface, remove dust, dirt, loose particles and unsound substrate and grading with cement mortar (1:4), 10 mm thick, as in slab surfaces, beams, columns, parapet, and junction of walls etc., grading with a slope of 1 in 120 mixed with liquid/integral water proofing compound as per manugacturer\"s instruction as approved by GE (water proofing compound to be measured separately). (b) Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning the surface. (c) Over the coat of bitumen bonding layer as above APP modified polymeric membrane (weight not less than 3.0 Kg/Sqm and minimum 3 mm thick reinforced with polyester non wove fabric (weight not less than 150 gms/sqm), unrolled and bonded completely to the substrate with side over lap of 5 mm or end over lap of 100 mm. The overlaps are then sealed/ fused by flam technology method as per manufacture instruction. (d) Sealing edges well into grooves & protect with CM 1:2 complete all as specified and directed. |
| 49 | M&L for applying a coat of aluminium paint @ 200 gm/sqm in two coats over polymeric membrene at non approchable roof complete all as specified and directed. |
| 50 | M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in roof kerbs or mud stops, rounded or chamfered on edge including all necessary formwork complete all as specified and directed. |
| 51 | S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkhat of size 65x 125 mmof double rebates comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr incharge complete all as specified and directed.Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 52 | S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engr incharge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 53 | S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge complete all as specified and directed.Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. |
| 54 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineering- Charge complete all as specified and directed.Note: stainless steel butt hinges shall be paid separately under relevant item |
| 55 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineering- Charge.(Note: stainless steel butt hinges shall be paid separately under relevant item). |
| 56 | Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardware should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer\"s specification & drawings complete all as specified and directed.Note: Fixture/fittings shall be measured & paid under relevant item |
| 57 | S&F powder coated (minimum power coating 50 micron) to aluminum frame / guiding railfor sliding or side hungwindows/ventilators frame including jointing cleats,glazing clips and fixing complete with one or more rebates for fixing etc complete all as specified and directed. |
| 58 | S&F powder coated aluminium (minimum thickness of powder coating 50 microns) sliding type three track (02 glazed shutters and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick tinted glass and mosquito proofing net as detailed below complete all as specified and directed: -(i) Frame section 91.85 X 31.75 X 1.30 mm, section No. 8758 for top and sides rails and 91.85 X 31.75 X 1.20 mm for bottom rail, section No. 8687. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.50 mm, section No. 8820.(iii) Glass 5 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips bearing section No. 4407 and necessary handles, tower boltetc. as directed. (iv) Stainless steel wire cloth (v) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight.(vi) Locking arrangement and providing Namda rope to make the frames air tight. |
| 59 | M&L for Mild steel Framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screwsconfirmingto Fe.290.Gde-E-165completeallasspecifiedand directed. |
| 60 | S&F 150 mm Stainless steel butt hinges, with stainless steel hinge pin,complete all as specified and directed |
| 61 | S&F 100 mm Stainless steel butt hinges, with stainless steel hinge pin,complete all as specified and directed |
| 62 | S&F Mortise Door Handle Lock for Main & Internal Door in Residential & Commercial Spaces, 200 mm handle, with Lock Body & 3 Keys type 4 levers (Make : Harrison, Godrej, Link) complete all as specified and directed by Engineer-in-Charge. |
| 63 | S&Fheavy duty door magnet stopper is constructed of high quality virgin plastic, solid, sturdy and rust-Prooffor hold and clatch fixing to back side of door shutter including all fixing items complete all as specified and directed. |
| 64 | S&F Stainless steel barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed. |
| 65 | S&F Stainless steel decorative handles of extruded section and fixed 150 mm long complete all as specified and directed. |
| 66 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed. |
| 67 | Removing surplus excavated soil to a distance not exc 50 Mtr & depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as specified and directed. |
| 68 | S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars,barred iron doors, ladders, framed balusters, walk ways, railings and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed. |
| 69 | M&L for machine cut Kota stone slab20-25 mm thick in floor on steps and landing in single piece over 20mm thick cement screed and jointed with ditto as per item over and including cement screed base of CM 1:3 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing (granite finish) and exposed edges of Kota stone shall be rounded complete all as specified and directed by Engr in charge. |
| 70 | All as per Item No 69.00 above but in vertical surface as in riser of steps, skirting, dado and pillars over 10mm thick back coat in CM 1:3 complete all as specified and directed. |
| 71 | S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, MS door shutter etc complete, drill for fixing of steel sheeting or other covering etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting and also fastening and fixing complete all as specified and directed. |
| 72 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 73 | S&F medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 15 mm bore GI tubings complete all as specified and directed. |
| 74 | S&F medium grade galvanised steel tubing with all fittings fixed to walls and ceilings or laid in floors for 25 mm bore GI tubings complete all as specified and directed. |
| 75 | M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturved surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed. |
| 76 | S&F gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed for 25mm dia pipe (ISI Marked) complete all as specified and directed. |
| 77 | All as per item No 76.00 above but for 40mm dia pipe complete all as specified and directed. |
| 78 | S&F tile Insert Shower Drain Channel (24 x 3 Inches)Trap complete all as specified and directed. |
| 79 | S&F Square 150x150mm 304-Grade Floor Drain with Collar, Hinge or without hige top openable withCockroach Trap complete all as specified and directed. |
| 80 | S&F bath room vanity unit of overall size 600x450x650 (approx)with multiple cabins with outside openable two shutter made of water proof coating/ items/ with two nos of 100mm stainless steel handle with hinges and auto closing and 16-18mm thick black polish granite with front and back side 12mm projection or as directed at site suitable hole for wash basin complete all as specified and directed. |
| 81 | S&F Table Top while ceramic basin of Size: approx 52x42x15 cm table mouted type including cuplinkwith stainless steel bottle trap of 32mm size with 250mm long (Make Jaquar, Hindware, Kohler) to fix on stone base and all fittings to proper functional condtion complete all as specified and directed by Engr in charge.Make of basin: Jaquar Cat Part No JDS-WHM-25907N/ Hindware cat Part No 91090/ CERA Cat Part No S2020153/ Kohler Cat Part No K-31459IN-0 |
| 82 | S&F Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, including Exposed and Concealed Part (diverter) Cartridge Sleeve, Wall Flange, Nipple & Spout suitable for basinincluding all fittings complete all as specified and directed.Make: Jaquar cat part no OPP-CHR-15233NKPMM & ALD-235N, Kohler Cat Part No K-22540IN-4ND-CP, Hindware Cat Part No F570029, CERA Cat Part No F1023474 and F4065103 |
| 83 | S&F 3 in 1 concealed single lever shower mixer, Shower System, 300mm Shower with arm, hand shower 1m to 1.2m connection and one spoutwith 10 layersurface finished,Shower System owns a modern and stylish look . Excellent plating technology prevents the coating from falling off, after a long time use still keep the surface smooth and clean will all connected items all as specified by manufacture complete all as specified and directed by Engr in charge.Make: Jaquar Cat Part No KUP-CHR-35125PM , Hindware Cat Part No F570022CP, KOHLER Cat Part No K-98754IN-4-CP, CERA cat Part No F1015403 |
| 84 | S&F 15mm bore two way Bib tab (spout) whilewith Wall Flangecomplete all as specified and directed.Make: Jaquar Cat Part No OPP-CHR-15041PM, Hindware Cat Part No F320005, KOHLER Cat Part No : K-16093IN-4-CP, CERA Cat Part No F1021163 |
| 85 | S&F 15mm bore Angular Stop Cock with Wall Flange while complete all as specified and directed.Make : Jaquar Cat Part No OPP-CHR-15053PM, Hindware Cat Part No F570043, KOHLER Cat Part No 11568IN-7BCP, CERA CAT Part NO F1015201 |
| 86 | S&F Vitreous China rimless wash down water closet pan single piece symphonic action, white, including soft close sheet cover of closed pattern with flat bottomcomplete all as specified and directed.Make: Hindware Cat part No 92573, Jaquar Cat Part No WC OPS-WHT-15853S300UF,Kohlar Cat Part No 77739T-SL-0,Cera cat Part No A1014110 |
| 87 | S&F brass chromium plated toilet paper holder, complete all as specified and directed.Make: Jaquar Cat Part No ACN-1151N, Kohler Cat Part No 5633IN, or Hindware cat Part NoF880003CP, CERA Cat Part No F5002110 |
| 88 | S&F ABS body Health Faucet including flexible pipe of 15 mm bore and min1.00M long with and including 15 mm bore complete all as specified and directed.Make: Jaquar Cat Part No ALD-CHR-573, Hindware cat Part No F160192CP, KOHLER Cat Part No 12927IN-CP, CERA Cat Part No F8030107AB |
| 89 | S&F fancy type stainless steeltowel rail of 600mm length complete all as specified and directed.Make: Hindware, Jaquar, CERA or Kohler |
| 90 | S&F Good quality Connection pipe (PVC) 15 mm dia and 450/600mm long complete all as specified and directed. |
| 91 | S&F rotational moulded polythene water storage tanks in triple layer (cylindrical verticalwith closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 1000 ltrs including dismantling of old PVC water tankandmaking connection with fitting for inlet & outlet pipe complete all as specified and directed. |
| 92 | M&L for providing PCC 1:2:4 type B2 (using 20mm garded stone agg) as in surface channel of drain complete all as specified and directed. |
| 93 | M&L for providing PCC 1:3:6 type C1 (using 20mm garded stone agg) as in coping PCC block etc complete all as specified and directed. |
| 94 | M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed. |
| 95 | Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed. |
| 96 | S&F precastPFRC rectangular manhole cover (medium duty) with size 1200mmX500mmX75mm thick, confirming to IS: 12592 and IS:1726, factory madecomplete all as specified and directed by Engr-in-charge. |
| 97 | M&L for 100 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or sub floors or path complete all as specified and directed. |
| 98 | M&L for providing 100 mm thick cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in path, hardstanding complete all as specified and directed. |
| 99 | M&L for Providing and laying 60mm thick factory made PU Coated chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 100 | M&L for PCC 1:2:4 type B-1 (using20 mm graded crushed stone aggregate) as incoping including weathering, slightly rounded or chamfered angles and throating, as directed and necessary form work complete all as specified and directed. |
| 101 | E&M PORTION:M&L for point wiringwith PVC insulated unsheathedmulti strandedFRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked andits accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for one light/ fan/ exhaust fan point controlled by one no, one way 5 Amp switch complete all as specified and directed.Note: (i)Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate.(ii)No cutting shall be done in the roof for laying PVC conduit for ceiling point wiring. In this specified portion wire shall run through the existing conduit or surface new conduit shall be provided as required.(iii) In case the wiring is encountered with any beam/column, then the wiring will run on surface to avoid any damage to the RCC portion. |
| 102 | All as per item No 101.00 above but one three pin 5 Amp socket outlet point controlled by one no, oneway switch on same board complete all as specified and directed. |
| 103 | All as per item No 101.00 above but one three pin 5 Amp socket outlet point controlled by one no, one way switch on independent board complete all as specified and directed. |
| 104 | All as per item No 101.00 above but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board complete all as specified and directed. |
| 105 | S&F modular Switch 6 amps, 230 vots, single pole, one way (ISI marked) with IP 20 rating complete all as specified and directed.Make : Havells Cat part No-ACNSXX101, Legrand Cat Part No-573400, Indoasian Cat part No-810600 |
| 106 | S&F 16 Amp rating modular switch one way one module with IP 20 rating complete all as specified and directed.Make : Havells Cat part No-ACNSXX161, Legrand Cat Part No-573410, Indoasian Cat part No-810601 |
| 107 | S&F modular socket out let 230 volts grade (as catered in point wiring above)6 Amp - 2/3 pin combined 2 modulecomplete all as specified and directed by Engr in charge.Make : Havells Cat part No-ACAKPXW063, Legrand Cat Part No-573470, Indoasian Cat part No-810620 |
| 108 | S&F modular socket out let 230 volts grade (as catered in point wiring above)16 Amp - 2/3 pin combined 2 module complete all as specified and directed by Engr in charge.Make : Havells Cat part No-ACAKPXW163, Legrand Cat Part No-573471, Indoasian Cat part No-810621 |
| 109 | S&F Modular MCB SP 16Amps 240V 3 KA, C Curve, fitted in main switch board, including 2.5 sqmm wire connecting power socket & modular MCB complete all as secified and directed by Engr-In-Charge.Make: Havells Cat Part No DHFNCSPA016 of Havells or equivalent in L&T/schneider. |
| 110 | S&F factory made SPNDB\"s double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coatedsurface mounting12 way SPN 220 Volts,with suitable busbar, neutral link & earth link suitable forcomplete all as specified and directed.Make: Legrand Cat Part No 507612, or equivalent model in L&T,Schneider. |
| 111 | S&F MCB, 6 to 32 Amps, 240V 10KA rupturing capacity IS 8828 marked, B or C curve the MCB DB, as per site requirement complete all as specified and directed. |
| 112 | All as per item No 111.00 above but MCB DP 32 Amps, B or C Curve as per site reqmt complete all as specified and directed. |
| 113 | S&F round shape 20 watt 220 volts AC surface mounted type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-charge.Make: Philips,Orient,Havells,Crompton,Bajaj,Jaquar. |
| 114 | S&F LED Tube light of 20 watt 230 volt (approx size 4 ft) box type complete with LED tube light 20 watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size having min P.F>0.95, minimum efficacy 120 lumen/watt IP 20 rating complete all as specified and directed.Make: Bajaj cat Part No BAJAJ BCLAB 20W CW LED XT, Crompton cat part No CCS-100-20-65-HL2-OP-NWH, Philips cat part No BN308C LED20S-6500 L120 PSU WH |
| 115 | S&F remote controlled BLDC ceiling fan 1400 mm sweep, with remote, having minimum CMM 260, operating at 230 volts, 50Hz, having full copper motor & powder coated ribbed aluminium blades for higher air delivery, longer life complete with all the accessories including making arrangements to hanging of fan to ceiling with proper hook, nut,bolts & remote stand complete all as specified & directed by Engineer-in-charge. Make :Atomberg Efficio model No EFC21435RM or equivalent in Havells,Crompton, Bajaj, Orient. |
| 116 | M&L for Earthing complete with galvanized iron earth plate electrode of size 600x600x6.0mm , buried directly in ground (earth pit not less than 2.25 mtrs below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts , nuts , check nuts and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate 20 mm dia watering pipe medium grade 1.70 mtr long with a plug at top, GI protection pipe light grade 15 mm dia from earth pit to main board including PCC pit in cement concrete 1:2:4 along with CI frame and cover 10mm thick duly hinged to CI frame as shown in the electrical plate No3 of SSR 2009 part 1 specification at page 497 complete all as specified and directed. |
| 117 | Supply and laying XLPE Insulated ,screened, PVC bedded, galvanized steel wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 2 core complete all as specified and directed by Engineer-in-Charge.Note:- Earth work incl excavation, returning filling, sand cushioning and removal if required or suggested by user and Engr-in-charge/fixing into wall or terrace or any type of surface by using suitable clamps shall be included in the quoted rate. |
| 118 | S&F Exhaust fan AC single phase 230/240 v of size 300 mm sweep 1400 rpm metal body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including hole making. Louver complete all as specified and directed by Engineer-in-Charge. Make:- Havells Cat Part No VENTILAIR DB , Bajaj Cat Part No MAXX AIR or equivalent in crompton. |
| 119 | S&Fceiling rose 3 terminal / PVC insulated body ISI Marked complete all as specified and directed. |
| 120 | S&F inverter LED security light luminaire 60 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiplte LEDshaving optical grade polycarbonate lens with 4 hours battery back up all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of lightwith GI bracket of suitable size and clamps with fixing accessories complete all as specified and directed.Make: Philips /Crompton /Bajaj /Orient |
| 121 | S&F Wall mounted decorative bedlight LED light of 3 W gooseneck arm easy to adjust premium material white metal 75lm/3000 K and superior finish energy saving with LED light source fixture, complete all as specified and directed by Engr-in-charge. Make: Philips cat part no 919215850324 or equivalent modelin Orient/ bajaj/ Jaquar.Note: (a) Srl Item No 05.00 to 07.00, 10.00, 18.00, 20.00, 21.00, 29.00, 30.00, 32.00, 33.00, 35.00, 37.00, 48.00, 58.00, 68.00 & 69.00 of BOQ and all bathroom fittings and sanitary items are major items for the subject tender and material in respect of these items shall be procured within one month after placing of work order and produced before Engg in Charge alongwith original purchase vouchers as per direction of Garrison Engineer and shall obtain a certificate from Engg in charge that material in respect of above mentioned items have been submitted in the office of Engg in charge in their safe custody.(b) Materials in respect of Freakishly low declared items if any at the time of acceptance of contract shall be procured within one month after placing of work order and submit the same in the office of Engg in charge alongwith original purchase vouchers in their safe custody and shall obtain a certificate from Engg in charge. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
