Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Servicing/Overhauling of 3 Phase 415 Volts 1440 RPM 150 HP/125 HP capacity Induction Motor (MAKE : KIRLOSKAR/ ALSTOM) installed at Jalkendra, Intermediate Pump House alongwith following others repairs :-(a)Taking out Motor from its Position by decoupling from Pump and disconnecting all Cable Connections.(b)Dismantling of induction Motor complete Part by Part carefully, testing all Coils, degreasing bearing and display all the Parts without damaging any portion for inspection of Engineer-in-Charge to ascertain the Serviceability of existing Parts.(c)Heating & Varnishing to Stator with super quality varnish and dried out properely with external heat as ordered and as directed.(d)Reassembeling the Motor complete with all existingServiceable Parts obtained , greasing the Bearing with bearing grease and new Parts as ordered by Engineer-in-Charge (New Parts shall be measured and paid separately under relevant Itemhere-in after) (e)Reinstall the Motor at its existing Position, couple with the Pump connecting all Cable connections and testing on completion complete all as specified and as directed. Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). .Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No-1to 5 but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 2 | Supply only DE ( Driver End ) Bearing No- NU318C3oras per existing size suitable for 150/125 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed. |
| 3 | Supply only NDE ( Non Driver End ) Bearing No- 6314C3 oras per existingsuitable for 150/125 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed. |
| 4 | Supply only Bakelite connection terminal plate with brass nuts bolts and washers suitable for 150/125 HP Motor against Item No. 1 here-in-above, complete all as specified and as directed. |
| 5 | Rewinding burnt coilsof Induction Motor stator of capacity 125 HP/150 HP obtained from Item Ser No-1 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding, cleaning/ repairing damaged slots, complete all as specified and as directed. |
| 6 | Servicing / Overhauling ofElectric driven Vertical / Horizontal NC split casing Pump-set having discharge 50000 GPH/ 60000 GPH, H 61-M ( Make- Kirloskar ) coupled with induction Motor125HP/ 150 HP capacityinstalled at Jalkendra, Intermediate Pump house along with following others repairs :- a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery waterconnections , setting aside Pumpfrom base plate ,b). Dismantling of Pump complete part by part carefully , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in-Charge to ascertain the serviceability of existing parts.c). Replacement of Gasket set and gland packing rope. d). Reassembeling the Pump complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after)e) Reinstall the Pump at its existing Position, couple with the Motor and connecting all suction delivery waterconnections and testing on completion complete all as specified and as directed.Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No-7to 16but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 7 | Supply only DE ( Driver End ) bearing as per existing size (Heavy Duty) of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 8 | Supply only NDE ( Non Driver End ) bearing as per existing size (Heavy Duty), of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 9 | Supply only SS Pump Shaft sleeveforPump shaft of HorizontalSplit casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 10 | Supply only Rubber tyre Coupling of Horizontal Split casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 11 | Supply only CI couplingtyre UNIQUE -PX-100 of HorizontalSplit casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 12 | Supply only CI Impeller HorizontalSplit casing Pump of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 13 | Supply only Pump Shaftof Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 14 | Supply only Oil Seal of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 15 | Supply only/ Topping up Engine Oil(20W50) of Horizontal casing Pump to incorporate against each Item No.6 here-in-above complete all as specied and as directed. |
| 16 | Welding Turningand machining works of Pump Shaft obtained from Item No 6 here-in-before to true size to match with the new Parts / existing serviceable parts forproperallignment and smooth operation of Motor Pump Set completeall as specified and as directed |
| 17 | Servicing / overhauling of 3 Phase 415 Volts 1440 RPM 75 HP capacity induction (Motor Make-Jyoti, Kirloskar, Becon ) Installed at Jalkendra Pump House, along with following others repairs :-a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Heating & varnishingto stator with super quality varnish and dried out properely with external heat as ordered & directed.d). Reassembeling the motor complete with all existingserviceable parts obtained , greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge. (New parts shall be measured and paid separately under relevant Itemhere-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completion complete all as specified and as directed. Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 18to 21but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 18 | Supply only DE ( Driver End ) Bearing No- NU314 / N 344oras per existingof Induction Motor against Item No-17 here-in-above complete all as specified and as directed. |
| 19 | Supply only NDE ( Non Driver End ) Bearing No - 6313 / 6311or as per existing sizeof Induction Motor against Item No-17 here-in-above complete all as specified and as directed. |
| 20 | Supply only Bakelite connection plate with brass nuts bolts and washersof Induction Motor against Item No-17 here-in-above complete all as specified and as directed. |
| 21 | Rewindingburnt coilsof Induction Motor stator of capacity 75 HP obtained from Item Ser No-17 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding, cleaning/ repairing damaged slots, complete all as specified and as directed. |
| 22 | Servicing / over hauling ofElectric driven Multi staging Pump set having discharge Cap 40000 GPH, H-61 M(PumpMake-BE, Alstom ) Installed at Jalkendra , coupled with induction Motor 75 HP capacity along with following others repairs :-a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery waterconnections , setting aside Pumpfrom base plate ,b) Dismantling of Pump complete part by part carefully , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Replacement of Gasket set and gland packing rope .d). Reassembeling the Pump complete with all existingserviceable parts obtained , greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after)e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery waterconnections and testing on completion completeall as specified and as directed.Note :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 23to 30but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 23 | Supply only DE ( Driver End ) bearing as per existing size(heavy duty) for pump coupled with 75 HP motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 24 | Supply only NDE ( Non Driver End ) bearing as per existing size( heavy duty) forpumpcoupled with 75 HP motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 25 | Supply only SS Pump Shaft sleeveforPump shaft of 75 HP Motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 26 | Supply only CI Impeller as per Existing of pump set forpumpcoupled with 75 HP motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 27 | Supply only Pump Shaft forpumpcoupled with 75 HP motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 28 | Supply only Rubber Tyre Coupling complete set UNIQUE -PX-90 forpumpcoupled with 75 HP motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 29 | Supply only CI couplingtyre only UNIQUE PX-90 forpumpcoupled with 75 HP motor to incorporate against Item No-22 here-in-above completeall as specified and as directed. |
| 30 | Welding Turningand machining works of Pump Shaft obtained from Item No 22 here-in-Before to true size to match with the new Parts / existing serviceable parts forproperallignment and smooth operation of Motor Pump Set completeall as specified and as directed |
| 31 | Servicing / over hauling of Electric Motor Vertical 3 Phase 415 Volts 1440 RPMcapacity40HP ( Make- Jyoti, CVO) .installed at Jalkendra, along with following others repairs.a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c) Heating & varnishingto stator with super quality varnish and dried out properely with external heat as ordered & directedd). Reassembeling the motor complete with all existingserviceable parts obtained , greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Itemhere-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 32to 35but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 32 | Supply onlyVertical Electric Induction Motor to incorporate against each Item No-31 here-in-above DE ( Driver End ) Bearingas per existingto incorporate against Item No-31 here-in-above completeall as specified and as directed. |
| 33 | Supply onlyVertical Electric Induction Motor to incorporate against each Item No-31 here-in-above NDE ( Non Driver End ) Bearingas per existingto incorporate against Item No-31 here-in-above completeall as specified and as directed. |
| 34 | Supply onlyVertical Electric Induction Motor to incorporate against each Item No-31 here-in-above Bakelite connection plate with brass nuts bolts and washers completeall as specified and as directed. |
| 35 | Rewindingburnt coilsof Vertical Electric Induction Motor stator cap 40 HP obtained from Item Ser No-31here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , completeas directed |
| 36 | Servicing / over hauling ofVertical TurbineMulti staging Pump installed Inslde Jackwell coupled with 40 HP Vertical Motor atJalkendra along with following others repairs.a).Decoupling Vertical Motor from Pump shaft and disconnecting all suction /delivery waterconnections , setting aside Motor from base plate ,Lifting column pipes and submersible multistaging Pump set from Jackwell ,setting aside and stacking column pipes for reuse complete all as directed by Engnr-in-Charge.b).Dismantling of Pump complete part by part carefully , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Replacement of Gasket set and gland packing rope .d). Reassembeling the Pump complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after)e) Loweringcolumn pipes and submersible multistaging Pump set inside Jackwell ,connecting Suction/ delivery Lines including replacement of nuts bolts , washers and rubber gasketf) Reinstall the pump at its existing Position , couple with the motor connecting all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 32to 56but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 37 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above CI Impeller complete all as specified and as directed. |
| 38 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Impeller Collet complete all as specified and as directed. |
| 39 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above GM BowelBushing complete all as specified and as directed. |
| 40 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Stain Less Steel (SS) Line Shaft 10\"- Long complete all as specified and as directed. |
| 41 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Stain Less Steel (SS) Top Shaft ( Motor Shaft) complete all as specified and as directed. |
| 42 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above SSSpider Guide Shaft Sleeve complete all as specified and as directed. |
| 43 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above SS lline/pump Shaft Coupler/ reduce Socket complete all as specified and as directed. |
| 44 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above SS lline Shaft Coupler/Socket complete all as specified and as directed. |
| 45 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above CIShaft Spider Guide ( 8\") dia complete all as specified and as directed. |
| 46 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Suction Case complete all as specified and as directed. |
| 47 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-aboveDischarge Case complete all as specified and as directed. |
| 48 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Impeller centre Bowl complete all as specified and as directed. |
| 49 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-aboveImpeller Top Bowl complete all as specified and as directed. |
| 50 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above VT Pump strainer complete all as specified and as directed. |
| 51 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Bowl studs complete all as specified and as directed. |
| 52 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above MSheavy duty column Pipe 200 mm Bore both ends flanged (3.0 Meter Long ) complete all as specified and as directed. |
| 53 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above MSheavy duty200mm dia flange only complete all as specified and as directed. |
| 54 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above MS Nut bolts with washers 5/8 dia and 3\"/6\" long complete all as specified and as directed. |
| 55 | Supply onlySubmersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above MS Nut bolts with washers 1/2\" dia and 3\" long complete all as specified and as directed. |
| 56 | Supply only Submersible Multi staging Pump coupled with 40HP VerticalMotor to incorporate against each Item No-36 here-in-above Rubber gasket 4/6 mm thick complete all as specified and as directed. |
| 57 | Servicing/over hauling of 3 Phase 415 Volts 1440 RPM20 HP (Motor Make--Kirloskar ) Installed at AIR OP pump House,Swimming Pool, Rekhamari , coupled with NC Horizontal Pumping Seta). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Heating & varnishingto stator with super quality varnish and dried out properely with external heat as ordered & directedd). Reassembeling the motor complete with all existingserviceable parts obtained , greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Itemhere-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 58to 64but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 58 | Supply only 20 HP Motor to incorporate against each Item No-57 here-in-above DE ( Driver End ) bearing as per existing sizecomplete all as specified and as directed. |
| 59 | Supply only 20 HP Motor to incorporate against each Item No-57 here-in-above NDE ( Non Driver End ) Bearing as per existing size complete all as specified and as directed. |
| 60 | Supply only 20 HP Motor to incorporate against each Item No-57 here-in-above Bakelite Terminal connection plate with brass nuts bolts and washers complete all as specified and as directed. |
| 61 | Supply only 20 HP Motor to incorporate against each Item No-57 here-in-above Plastic Rotar Fan complete all as specified and as directed. |
| 62 | Supply only20 HP Motor to incorporate against each Item No-57 here-in-above Tyre coupling complete set No-60/70 complete all as specified and as directed. |
| 63 | Supply only 20 HP Motor to incorporate against each Item No-57 here-in-above Tyre coupling Rubber tyre only No-60/70 complete all as specified and as directed. |
| 64 | Rewindingburnt coilsof Induction Motor stator cap 20 HP obtained from Item Ser No-57 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , completeas directed. |
| 65 | Servicing/over hauling ofElectric driven Horizontal split casing Pump set of Discharge cap 1230LPM, H-30M (Pump Make-Kirloskar , HBB)Installed at AIR OP pump House , Swimming Pool, Rekhamaricoupled with induction Motor 20 HP capacityalong with following others repairs.a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery waterconnections , setting aside Pumpfrom base plate ,b).Dismantling of Pump complete part by part carefully , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Replacement of Gasket set and gland packing rope .d). Reassembeling the Pump complete with all existingserviceable parts obtained , greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after)e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery waterconnections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 66to 71but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 66 | Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-65 here-in-above DE ( Driver End ) bearing as per existing size complete all as specified and as directed. |
| 67 | Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-65 here-in-above NDE ( Non Driver End ) bearing as per existing size complete all as specified and as directed. |
| 68 | Supply onlyPump coupled with 20 HP Motor to incorporate against each Item No-65 here-in-above SS Pump Shaft sleeve forPump shaft complete all as specified and as directed. |
| 69 | Supply onlyPump coupled with 20 HP Motor to incorporate against each Item No-65 here-in-above CI Impeller as per Existing complete all as specified and as directed. |
| 70 | Supply only Pump coupled with 20 HP Motor to incorporate against each Item No-65 here-in-above Pump Shaftcomplete all as specified and as directed. |
| 71 | Welding Turningand machining works of Pump Shaft obtained from Item No 65 here-in-Before to true size to match with the new Parts / existing serviceable parts forproperallignment and smooth operation of Motor Pump Set completeall as specified and as directed |
| 72 | Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 15 HP Motor Make-KirloskarInstalled atJalkendra Pump housea). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c)., Heating & varnishingto stator with super quality varnish and dried out properely with external heat as ordered & directedd). Reassembeling the motor complete with all existingserviceable parts obtained , greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Itemhere-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 73to 77but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 73 | Supply only 15 HP Motor to incorporate against each Item No-72 here-in-above DE ( Driver End ) bearingas per existing sizecomplete all as specified and as directed. |
| 74 | Supply only 15 HP Motor to incorporate against each Item No-72 here-in-above NDE ( Non Driver End ) Bearingas per existing size complete all as specified and as directed. |
| 75 | Supply only the following Items ( PROVISIONAL)of 15 HP Motor to incorporate against each Item No-72 here-in-aboveBakelite Terminal connection plate with brass nuts bolts and washers complete all as specified and as directed. |
| 76 | Supply only the following Items ( PROVISIONAL)of 15 HP Motor to incorporate against each Item No-72 here-in-above Plastic Rotar Fan complete all as specified and as directed. |
| 77 | Rewindingburnt coilsof Induction Motor stator cap 15 HP obtained from Item Ser No-72 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete all as directed |
| 78 | Servicing / over hauling ofElectric driven Horizontal split casing Pump set of Pump Discharge 26.5 LPS, H-21.5M,(Pump Make-Kirloskar ,)Installed at Jalkendra Pump Housecoupled with 15 HP Motor along with following others repairs.a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery waterconnections , setting aside Pumpfrom base plate ,b).Dismantling of Pump complete part by part carefully , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Replacement of Gasket set and gland packing rope .d). Reassembeling the Pump complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after)e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery waterconnections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 79to 86but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 79 | Supply only NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-78 here-in-above DE ( Driver End ) bearing as per existing sizecomplete all as specified and as directed. |
| 80 | Supply only NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-78 here-in-above NDE ( Non Driver End ) bearing as per existing size complete all as specified and as directed. |
| 81 | Supply only NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above SS Pump Shaft sleeveforPump shaftcomplete all as specified and as directed. |
| 82 | Supply onlyNC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-aboveCI Impeller as per Existingcomplete all as specified and as directed. |
| 83 | Supply only of NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-86 here-in-above Pump Shaftcomplete all as specified and as directed. |
| 84 | Supply only NC Horizontal/ Vertical Pump coupled with 15 HP Motor to incorporate against each Item No-78 here-in-above tyre Coupling complete set No.60 complete all as specified and as directed. |
| 85 | Supply only Star RubberCouplingof NC Horizontal/ Verticalsplit casing Pump coupled with 15 HP Motor to incorporate against each Item No-78 here-in-above completeall as specified and as directed. |
| 86 | Welding Turningand machining works of Pump Shaft obtained from Item No 78 here-in-Before to true size to match with the new Parts / existing serviceable parts forproperallignment and smooth operation of Motor Pump Set completeall as specified and as directed |
| 87 | Servicing / over hauling of 3 Phase 415 Volts 1440 RPM 10 HPMotor (Make-Kirloskar, Jyoti , CG ) Installed atAIR OP pump House , Rekhamari Pump Housea). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c)., Heating & varnishingto stator with super quality varnish and dried out properely with external heat as ordered & directedd). Reassembeling the motor complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Itemhere-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 88to 91but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 88 | Supply only 10 HP Motor to incorporate against each Item No-87 here-in-above DE ( Driver End ) bearing as per existing sizecompleteall as specified and as directed. |
| 89 | Supply only 10 HP Motor to incorporate against each Item No-87 here-in-above NDE ( Non Driver End ) Bearing as per existing size completeall as specified and as directed. |
| 90 | Supply only 10 HP Motor to incorporate against each Item No-87 here-in-above Bakelite connection plate with brass nuts bolts and washers completeall as specified and as directed. |
| 91 | Rewindingburnt coilsof Induction Motor stator cap 10 HP obtained from Item Ser No-87 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , completeas directed |
| 92 | Servicing / over hauling ofElectric driven Horizontal split casing Pump set of Pump Discharge Centrifugal 10000 - GPH, H- 40M, 10 HP,(Pump Make-Kirloskar ,BE, Jyoti ) Installed atAIR OP pump House , Rekhamari Pump Housealong with following others repairs.a). Taking out Pump from its Position by decoupling from Motor and disconnecting all suction /delivery waterconnections , setting aside Pumpfrom base plate ,b).Dismantling of Pump complete part by part carefully , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Replacement of Gasket set and gland packing rope .d). Reassembeling the Pump complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under appropraite Item here-in-after)e) Reinstall the Pump at its existing Position , couple with the Motor and connecting all suction delivery waterconnections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 93to 100but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 93 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-92 here-in-above DE ( Driver End ) bearing as per existing size completeall as specified and as directed. |
| 94 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-92 here-in-above NDE ( Non Driver End ) bearing as per existing sizecompleteall as specified and as directed. |
| 95 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above SS Pump Shaft sleeveforPump shaftcompleteall as specified and as directed. |
| 96 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-100 here-in-above CI Impeller as per Existing completeall as specified and as directed. |
| 97 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-92 here-in-above Pump Shaftcompleteall as specified and as directed. |
| 98 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-92 here-in-above tyre Coupling complete set No.60 completeall as specified and as directed. |
| 99 | Supply only NC Horizontal split casing Pump coupled with 10 HP Motor to incorporate against each Item No-92 here-in-above tyre copling rubber only N0.60 completeall as specified and as directed. |
| 100 | Welding Turningand machining works of Pump Shaft obtained from Item No 92 here-in-Before to true size to match with the new Parts / existing serviceable parts forproperallignment and smooth operation of Motor Pump Set completeall as specified and as directed |
| 101 | Servicing/over hauling of 3 Phase 415 Volts 1440 RPM 5 HP (Motor Make-Kirloskar, CG) Installed atJalkendra, 206 AVN and 1880 Rkt offr mess. a). Taking out Motor from its Position by decoupling from Pump and disconnecting all cable connections b) Dismantling of induction Motor complete part by part carefully , testing all coils , degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.c). Heating & varnishingto stator with super quality varnish and dried out properely with external heat as ordered & directedd). Reassembeling the motor complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Itemhere-in after) e) Reinstall the Motor at its existing Position , couple with the Pump connecting all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 93to 100but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 102 | Supply onlyMotor to incorporate against each Item No-101 here-in-above DE ( Driver End ) bearing as per existing size suitable forCap 5 HP Electric induction Motor completeall as specified and as directed. |
| 103 | Supply only Motor to incorporate against each Item No-101 here-in-above NDE ( Non Driver End ) Bearingas per existing size suitable forCap 5 HP Electric induction Motor completeall as specified and as directed. |
| 104 | Supply onlyMotor to incorporate against each Item No-101 here-in-above Bakelite connection plate with brass nuts bolts and washers suitable for Motor cap 5HP completeall as specified and as directed. |
| 105 | Rewindingburnt coilsof Induction Motor stator cap 5 HP obtained from Item Ser No-101 here-in-above with super enamelled copper winding wire as per existing size and guage to achieve therequired /specifiedRPM including taking out old unserviceable winding ,cleaning/ repairing damaged slots , completeas directed |
| 106 | Servicing / over haulingof 3 Phase 415 Volts, 50 Hz , RPM 2900Submersible Motor Pump setof capacity upto 30/25/22.5/20 HP( Make- Calama, Texmo, KSB,) installed installed inside borewell and jackwell at Jalkendra , Rekhamari , AOP Pump House along with following others repairs.(a). Disconnecting delivery waterconnectionsLifting column pipes along with connectedsubmersible motor Pump set, submersible cableby making necessary arrangements from bore well ,setting aside and stacking column pipes for reuse complete all as directed by Engnr-in-Charge.(b) Dismantling of Submersible Motor Pump- Setcomplete part by part carefully, testing all coils of submersible Motor, degreasing bearingand display all the parts without damaging any portion for inspection of Engineer-in- Charge to ascertain the serviceability of existing parts.(c). Reassembeling the motor complete with all existingserviceable parts obtained, greasing the bearing with bearing grease , andnew parts as ordered by Engineer in Charge.( New parts shall be measured and paid separately under relevant Itemhere-in after) (d). Painting the repaired motor and column Pipes externally with onecoats of red oxide paint and two coat of syntheticenameal paint of shade as directed by Engnr-in-Charge.(e) Reinstall the Motor at its existing Position by Loweringcolumn pipes and submersible MototPump set inside Bore well ,connecting Suction/ delivery Lines, all cable connections and testing on completionNote :- (i). Any Parts required for replacement shall be measured and paid seperately under appropriate item as \"\"Supply only\"\" (s) of this schedule. However labour element involved in replacementis included in unit rate quoated against this Item.(ii). Any unforeseen minor repair and minor parts ( Total cost less than Rs 200 ) that are not covered under Item No- 107to 127but required to complete the repair work / smooth functioning of Motor shallbe deemed to be included with the unit rate .Transportation of Stator / Rotorparts for machining , rewinding at lathe shop at Tezpur / Rangapara is also deemed to be included with unit rate.iii). Rewinding of stator / rotor of motor, any machine workwhere involved shall be measured and paid separetely against relevant item of this schedule. |
| 107 | Supply only Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Suction Casing completeall as specified and as directed. |
| 108 | Supply only Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Stage Bowl completeall as specified and as directed. |
| 109 | Supply only Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above M S Suction Strainer completeall as specified and as directed. |
| 110 | Supply only Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above SS Pump Shaftcompleteall as specified and as directed. |
| 111 | Supply only Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Bronze Impeller completeall as specified and as directed. |
| 112 | Supply onlySubmersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Valve Body completeall as specified and as directed. |
| 113 | Supply only Submersible Multi staging Mixed Flow Pump coupled with submersible motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Rubber Oil Seal completeall as specified and as directed. |
| 114 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Adapator completeall as specified and as directed. |
| 115 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Bronze Sand Guard completeall as specified and as directed. |
| 116 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Thrust Bearing Housing completeall as specified and as directed. |
| 117 | Supply onlySubmersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Bearing Body completeall as specified and as directed. |
| 118 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Bronze Thrust bearingPlate completeall as specified and as directed. |
| 119 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Bronze Thrust Bearing segments completeall as specified and as directed. |
| 120 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above CI Bearing segment carrier completeall as specified and as directed. |
| 121 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Bronze bearing Bush completeall as specified and as directed. |
| 122 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Rubber Diaphragm completeall as specified and as directed. |
| 123 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above Cr. St. Coupling Sleeve completeall as specified and as directed. |
| 124 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above MSheavy duty column Pipe 100mm Bore both ends flanged (3.0 Meter Long ) |
| 125 | Supply only Submersible Motor upto capacity 20 HP to 30 HPto incorporate against each Item No-106 here-in-above MSheavy duty column Pipe 80mm Bore both ends flanged (3.0 Meter Long ) completeall as specified and as directed. |
| 126 | Rewindingstator of submersiblemotor ofcapacity 25/ 30 HP obtained from Item Ser No-106 here-in-above with water proof insulated copper wire of existing guage and size to achieve the specified / required RPMincluding taking out old unserviceable winding ,cleaning/ repairing damaged slots , complete all as specified and as directed. |
| 127 | Rewindingstator of submersiblemotor ofcapacity 20 /22.5HP obtained from Item Ser No-106 here-in-above with water proof insulated copper wire of existing guage and size to achieve the specified / required RPMincluding taking out old unserviceable winding , cleaning/ repairing damaged slots ,complete all as specified and as directed. |
| 128 | Material and labour forPVC insulated and sheathed flat 3 core, Size 4 Sqmmcopper stranded conductorwater proof submersible cable 1100 Volts Grade , and connecting tosubmersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed. |
| 129 | Material and labour forPVC insulated and sheathed flat 3 core, Size 6 Sqmmcopper stranded conductorwater proof submersible cable 1100 Volts Grade , and connecting tosubmersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed. |
| 130 | Material and labour forPVC insulated and sheathed flat 3 core, Size 10 Sqmmcopper stranded conductorwater proof submersible cable 1100 Volts Grade , and connecting tosubmersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed. |
| 131 | Material and labour forPVC insulated and sheathed flat 3 core, Size 16 Sqmmcopper stranded conductorwater proof submersible cable 1100 Volts Grade , and connecting tosubmersible Motor pump set & starter securing with necessary clamps along the column Pipes including taking out old unserviceable cable complete all as specified and as directed. |
| 132 | Supply, laying , fixing , passing through pipe or cable tray PVC insulated &PVC sheathed unarmouredMulti core copper conductor 3 core 50 Sqmm 1100 Volts Grade cable confirming to IS 694 includingincluding taking out old unserviceable cable connected from electric induction Motor to starter complete all as specified and as directed. |
| 133 | Supply, laying , fixing , passing through pipe or cable tray PVC insulated &PVC sheathed unarmered Multi core copper conductor 1 core 95 Sqmm 1100 Volts Grade cable confirming to IS 694 includingincluding taking out old unserviceable cable connected from electric induction Motor to starter complete all as specified and as directed. |
| 134 | Supply, laying , fixing , passing through pipe or cable tray PVC insulated &PVC sheathed unarmered Multi core copper conductor 1 core 70 Sqmm 1100 Volts Grade cable confirming to IS 694 includingincluding taking out old unserviceable cable connected from electric induction Motor to starter complete all as specified and as directed. |
| 135 | Scraping old paint of Electric induction Motor 150/125 HP Motor , NC Vertical/ Horizontall Split casing Pump , Suction , delivery Pipes, sluice valves , NRV Valvesat Jalkendra , IMPH Pump House (Approx coverage area-10-15 Sqm) and Painting with onecoats of red oxide paint and two coat of syntheticenameal paint of shade as directed by Engnr-in-Charge including writing Sm No. , MES No.complete as all specified and as directed |
| 136 | Scraping old paint of Electric induction Motor 75 HP Motor , NC Vertical/ Horizontall / Multi stagingPump , Suction , delivery Pipes, sluice valves , NRV Valvesat Jalkendra(Approx coverage area-10-12 Sqm) and Painting with onecoats of red oxide paint and two coat of syntheticenameal paint of shade as directed by Engnr-in-Charge including writing Sm No. , MES No.complete as all specified and as directed |
| 137 | Scraping old paint of Electric induction Motor 20/15 HP Motor , NC Vertical/ Horizontall / Multi stagingPump , Suction , delivery Pipes, sluice valves , NRV Valvesat Jalkendra ,Swimming Pool, Rekhamari,(Approx coverage area-8-10 Sqm) and Painting with onecoats of red oxide paint and two coat of syntheticenameal paint of shade as directed by Engnr-in-Charge including writing SM No. , MES No.complete as all specified and as directed |
| 138 | Scraping old paint of Electric induction Motor 10/7.5 HP Motor , NC Vertical/ Horizontal, Suction , delivery Pipes, sluice valves , NRV Valves (Approx coverage area-5-7 Sqm) and Painting with onecoats of red oxide paint and two coat of syntheticenameal paint of shade as directed by Engnr-in-Charge including writing Sm No. , MES No.complete as all specified and as directed |
| 139 | S&F in repair Cast Iron Foot valve of size 80mm to suction Pipe of MotorPump setby disconnectingLifting suction Pipe from shallow well/ UG Sumpand fixing in Position complete all as specified and as directed |
| 140 | S&F in repair Cast Iron Foot valve of size 100 mm to suction Pipe of MotorPump setby disconnectingLifting suction Pipe from shallow well/ UG Sumpand fixing in Position complete all as specified and as directed |
| 141 | S&F in repair Cast Iron Foot valve of size 150mm to suction Pipe of MotorPump setby disconnectingLifting suction Pipe from shallow well/ UG Sumpand fixing in Position complete all as specified and as directed |
| 142 | S&F in repair Cast Iron Foot valve of size 200 mm to suction Pipe of MotorPump setby disconnectingLifting suction Pipe from shallow well/ UG Sumpand fixing in Position complete all as specified and as directed |
| 143 | S&F in repair Cast Iron NRV of size 150 mm with gun metal seat PN 1.6to delivery Pipe of MotorPump setfixing in Positioncomplete all as specified and as directed |
| 144 | S&F in repair Cast Iron NRV of size 200 mm with gun metal seat PN 1.6to delivery Pipe of MotorPump set fixing in Position valve complete all as specified and as directed |
| 145 | S&F in repair Cast Iron Diaphragm Valve of size 125 mm wheel type with necessary Nut, Bolts, Gasket, Washer, etc. complete all as specified and as directed. |
| 146 | S&F in repair Cast Iron Diaphragm Valve of size 150 mm wheel type with necessary Nut, Bolts, Gasket, Washer, etc. complete all as specified and as directed. |
| 147 | Repair to water level indicator ofOH Reservoirby replacement of brass float ball 300 mm dia 2mm thick mild steel pulley flexible steel wire rope from brass float ball to measuring key and painting to indicator with 2 coat of synthetic enamelpaint and marking number, strip for measuring of water level at OHT with red/black/Yellow reflective type colour complete and all as directed. |
| 148 | Desliting/Taking out accumulated Silt, Sand , Mud etc.,from Jack well of diameter 6.10 Metre and 12.20 Metre deep ( installed at Jalkendra & old pump house) through Manhole, removing the same to a distance not exc. 50 Metre, complete all as specified and as directed. Note : (i) The contractor to monitor day to day and avoid damage of VT pumpset due to intake of sand/mud(accumulated into bowl assembly (ii) Any damage made to Jack well, the contractor is fully responsible for repair the same without any extra payment. |
| 149 | Desliting / Taking out accumulated Silt, Sand ,Mud etc from Sand Trap of diameter 2.30 Metre and 3.00 Metre deep (installed at Jalkendra & Old Pump House) through Manhole, removing the same to a distance not exc. 50 Metre and depositing, complete all as specified and as directed. |
| 150 | Desliting / Taking out accumulated Silt, Sand ,Mud etc from Sand Catchment near River Bed Collection Chamber of Size 18.25 Metre x 4.57 Metre and 2.45 Metre deep , removing the same to a distance not exc. 50 Metre complete all as specified and as directed. |
| 151 | Desliting / Taking out accumulated sludge , Silt , Mudetc., from Flocculation Chamber, Flush mixing chamber , Clarifier Chamber , connected channels including scrapping down and cleaning internal surface of walls , Floors, Roofs, Mechanical Parts and cleaning blockage of wash out channels , pipes Drainage system etc. and removing the same to a distance not exc. 50 Metre complete all as specified and as directed. |
| 152 | Desliting / Taking out accumulated sludge , Silt , Mudetc., from Aeration Chamber installed at Jalkendra including scrapping down and cleaning internal surface of walls , Floors, Roofs, Mechanical Parts and cleaning blockage of wash out channels , pipes Drainage system etc. and removing the same to a distance not exc. 50 Metre and depositing complete all as specified and as directed. |
| 153 | Scrapping down , cleaning Internal Surfaces of Walls, Floors, Roofs, Drainage system etc of Under Ground Clear water sump ( installed at Jalkendra, IMPH ) of size 30.00 x 30.00 x 2.60 Metre including removing the accumulated sand/ silt from the chambers, depositing where directed atdistance not exc. 50 Metre complete all as specified and as directed. |
| 154 | Desilting/Taking out accumulated Silt, mud etc from temporary open channels of size 1.5 metre wide and 5 metre deep, connecting from main stream of river Gabru to sand trap near Jackwell at Jalkendra including removing the accumulated sand/ silt from the channels depositing where directed atdistance not exc. 50 Metre complete all as specified and as directed. |
| 155 | Desilting of Sludge Pit and Manhole to bring water from river to collection chamber/jackwell at Jalkendra including removing the accumulated sand/ silt from the channels depositing where directed atdistance not exc. 50 Metre complete all as specified and as directed. |
| 156 | M&L cutting/Cleaning amd removing of all unwanted vegetations, bushes, grasses, roots ,etcand removing to a distance not exc 50mtrs complete all as specified and as directed. |
| 157 | M& L preparation to CI/DI MS rising, distribution, overflow, wash out and suction pipe line of dia 150mm to 300 mm in vertical/ horizondal position and painting two coat of super enameled black or sky blue paint over a coat of red oxcide duly marked inlet/outlet direction, overflow/ washout at various water supply installation/ OHT at any height/ staging under GE Missamari all as directed Note: Therate quoted id deemed to inclusive for making arrangement for stage/ ladder for painting work. |
| 158 | M&L preparation ofoldsteel surfaces of valve pit chamber cover with angle iron frame of size 900mm x 900mm and applyingone coat of super enameled black paint complete all as specified and as directed |
| 159 | M&L preparation to surfaces of sluice/release/NRV Valves of size 300/250 mm diaand applyingone coat of super enameled black paint complete all as specified and as directed |
| 160 | Supply only grease for lubrication of bearings AP 3 moving parts of motors/pumpsets/chain pulleys etc complete all as specified and as directed |
| 161 | Supply only Brass bar/ block for making of brass bushing as per existing size for existing housing of various pump sets, induction motor and submersible pump complete all as specified and directed by Engineer-in-Charge |
| 162 | Supply of JCB/Fork land for removal of Silt/Gravels in the open drain from Ghabharu River to sand catcher at Jalkendra all as specified and directed by EIC Note:- (a) Rate quoted is deemed to inclusive of payment of Driver, Feul, Coolent, Lubricant or any other acessories as required (b) No additional charges will be paid for the T&P required.(c) Work shall be carried out only in written orders of Engg-In-Charge, and duty roster mentioning the Vechile Registration No. shall be maintained for start time and end time, date wise signed by JE, Engg-In-Charge,Contractor dully countersigned by GE. Photographic evidence shall be submitted to Engg-In-Charge as demanded and cost of Photos (One Photo per hour) is deemed to be inclusive in the unit rate quoted. |
| 163 | Testing of raw and treated water sample collected from different pump houses (10 samples out of which 05 Nos for Raw water and 05 Nos for treated water sample every quaterly) ( i.e. Rekhamari PH, old pump house, Old Jalkendra PH, New Jalkendra PH, AF PH)for all parameters covering complete chemical and bacterilogical test from any Govt approved/recognised lab as approved by the GE and the test report of samples should be submmited to AGE E/M office with in 15 days of sample submitted to lab. complete all as specified and as directed. Note:- (i) The Water test should be carried out at quarterly basis. (ii) The testing parameters will be as per norms decided by Eng-in-Charge |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
