|
| 1 | Demolition of brickwork or stone boulder masonry built in cement or cement lime mortar etc complete all as specified and Engr-in-charge |
| 2 | M&L for Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius old size bricks built in cement mortar 1:6 complete all as specified and directed. |
| 3 | Taking down cement plaster any description and the like on brick or stone walls, etc including raking out joints,hacking for key, scrubbing down with water etc complete all as specified and Engr-in-charge |
| 4 | M&L for15mm thick in CM 1:4 rendering on fair faces ofbrick or concrete surfaces finished even and smooth (without usingextra lime or cement) and with using liquid integral water proofing compound as per manufaturer\"s instructions on wall etc complete all as specified and Engr-in-chargeNote:WPC shall bemeasured and paid seperately. |
| 5 | M&L for prepartion of newly plastered surfaces and applying two coats of cement based paint over Chalk whiting, on plastered surfaces, prepara-tory to distempering etc complete all as specified and Engr-in-charge |
| 6 | Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and Engr-in-charge |
| 7 | S&F for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-410- W(Gde- E-250) quality-A etc complete all as specified and Engr-in-charge |
| 8 | M & L Punched tape concertina coil of 1050 mm dia, 56 loops, 2.5 mm core wire, heavy galvanised (wire-275 GSM), tensile strength of wire 1450- 1500 N/Sqmm, (weight 15.20 Kg/Coil +/- 5%), stretchable length 15 m including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and as directed by Enginner-in-Charge. |
| 9 | S & F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)etc complete all as specified and as directed by Enginner-in-Charge |
| 10 | Restraining rescuring of existing galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings including making good stappleetc complete all as specified and as directed by Enginner-in-Charge |
| 11 | Dismantling wire mesh of any typeetc complete all as specified and as directed by Enginner-in-Charge |
| 12 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provission of binding wireetc complete all as specified and as directed by Enginner-in-Charge |
| 13 | Supply only Chain link MS galvanisd fencing, having nominal pitch size 75 X 75mm and 4mm dia wire complete all as specified andetc complete all as specified and as directed by Enginner-in-Charge |
| 14 | Excavation in post holes or similar holes each n exc 0.5 cum getting out in soft/loose soil, returning filling in and ramming earth of broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50m and making good surface in any type of soil.etc complete all as specified and as directed by Enginner-in-Charge |
| 15 | M&L PCC 1:2:4 type B2 (using 40mm graded crushed stone agg)as in foundation of posts and struts.etc complete all as specified and as directed by Enginner-in-Charge |
| 16 | S & F of mild steel angle iron posts and struts in fencing including cutting tops to shape as directed,drilling holes, notching for wire, etc ; MS Round Bars, flat iron fillets (for securing wire mesh etc) including all necessary drilling, boldting or reveting, welding etc.,and smilar work concerming to Fe-290 Gde 165 complete all as specified and directed.etc complete all as specified and as directed by Enginner-in-Charge |
| 17 | M&L 10mm dia MS round bar for fixing of chain link fencing with posts.etc complete all as specified and as directed by Enginner-in-Charge |
| 18 | M&L for FIfor fixing chain link fencing with posts for inserting mesh etc complete. etc complete all as specified and as directed by Enginner-in-Charge |
| 19 | S&F 10mm dia 40mm long MS screw bolt machine made with hexagonal or square head at one end and screwed the other with washeretc complete all as specified and as directed by Enginner-in-Charge |
| 20 | M&L for cement concrete type C1 ( 1:3:6) with 20mm graded aggregate as inCoping andfilling in support of angles including necessary formworketc complete all as specified and as directed by Enginner-in-Charge |
| 21 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of steel surfaces.etc complete all as specified and as directed by Enginner-in-Charge |
| 22 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces n exc 10 cm width or girth when unconnected with other painting including preparation of steel surfaces. etc complete all as specified and as directed by Enginner-in-Charge |
| 23 | S&F for 0.63mm thick Galvanised, corrugated mild steel sheeting joint with L Jointwith two corrugations side lap, fixedwithcoach screws and washers, in roofs, walls etc. with grade of zinc coating 275 etc complete all as specified.etc complete all as specified and as directed by Enginner-in-Charge |
| 24 | M&L Providing precast cement concrete set in cement mortar 1:4 type B0 (1:2:4, using 12.5mm aggregate) louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding frame (Pre cast frame shall be measured separately and paid foretc complete all as specified and as directed by Enginner-in-Charge |
| 25 | S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins, posts where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including all necessary drilling, boldting or reveting, welding etc.,and smilar work concerming to Fe-290 Gde 165 complete all as specified and directed. |
| 26 | M&L for treating small articles such as ends of posts, holdfasts etc with tar or coal tar black paint; area exc 0.1 Sqm but n exc 0.5 Sqm each |
| 27 | Excavation in trenches n exc 1.5 mtr wide and not exc 1.50 mtr depth and getting out in soft/loose soil, complete all as specified |
| 28 | M&L cement concrete in foundation , filling and mass conrete type D2, (1:4:8) using 40mm grade stone aggregate complete all as specified |
| 29 | M&L Brickwork with fly ash bricks, straight or curvedb on plan exc 6m meanradius, built in Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified |
| 30 | M&L two coats of cement base paint on walls over one coat of alkali resistant primer including prepration of new plastered surface complete all as specified. |
| 31 | M&L for 75mm thick PCC (1:4:8) type D-2 by using 40mm graded aggregateas in sub floor complete all as specified |
| 32 | M&L 50mm thick PCC 1:2:4 type B1 as in flooring, surfaces finished even and smooth w/o using extra cement complete all as specified and as directed. |
| 33 | S & F Pre-painted galvalume alumunium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall ,fixed with self tapping screws as specified |
| 34 | Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point |
| 35 | S&F Glass dividing strips, 3 mm thick and 38mm width etc complete all as specified |
| 36 | M&L Granite (of any type) work (table rubbed and polished) , pillars, in cement mortar (1:4) including point-ing in white cement (1:2) us-ing marble dust with admix-ture of pigment to matchwith shade of granite. |
| 37 | M&L for rolled mild steel sections inStairs (framed) including stringers, treades, landing,balusters, hand rails etc. including cleats, brackets, etc. Fe 410-W(Gde-E- 250) quality-A complete all as specified and directed. |
| 38 | M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment welded to frames, steps etc Fe 410-W(Gde-E- 250) complete all as dspecified and diirected. |
| 39 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 40 | Supply only liquid water proofing compound as per manfacture instruction |
