|
| 1 | Providing and supply of C-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components to be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units shall be supported on heavy-duty steel frames fully carrying the load of worktops.. Its superior strength is combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame shall be constructed from a rectangular pipe with a cross section of 60mm x 30mm and shall be 2 mm thick and shall be without a vertical front leg to give a clean look. The C-frame legs shall be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient shall be well adjusted throughout the length of table and shall have horizontal supports for drainage systems. The structure shall have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. The C-frame shall be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths shall be 620 mm, 770 mm and 920 mm for wall side and 1540mm, 1840mm for Island tables. The Corner Units shall fit well with 770mm & 920mm table depths. All frame-work is to be pre-treated with superior pure epoxy powder coated finish. 900 Ht. Corner C-Frame Table |
| 2 | Providing and supply of C-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components to be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units shall be supported on heavy-duty steel frames fully carrying the load of worktops.. Its superior strength is combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame shall be constructed from a rectangular pipe with a cross section of 60mm x 30mm and shall be 2 mm thick and shall be without a vertical front leg to give a clean look. The C-frame legs shall be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient shall be well adjusted throughout the length of table and shall have horizontal supports for drainage systems. The structure shall have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. The C-frame shall be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths shall be 620 mm, 770 mm and 920 mm for wall side and 1540mm, 1840mm for Island tables. The Corner Units shall fit well with 770mm & 920mm table depths. All frame-work is to be pre-treated with superior pure epoxy powder coated finish.Common 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright |
| 3 | Providing and supply of C-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components to be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units shall be supported on heavy-duty steel frames fully carrying the load of worktops.. Its superior strength is combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame shall be constructed from a rectangular pipe with a cross section of 60mm x 30mm and shall be 2 mm thick and shall be without a vertical front leg to give a clean look. The C-frame legs shall be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient shall be well adjusted throughout the length of table and shall have horizontal supports for drainage systems. The structure shall have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. The C-frame shall be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths shall be 620 mm, 770 mm and 920 mm for wall side and 1540mm, 1840mm for Island tables. The Corner Units shall fit well with 770mm & 920mm table depths. All frame-work is to be pre-treated with superior pure epoxy powder coated finish.L.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright |
| 4 | Providing and supply of C-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components to be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units shall be supported on heavy-duty steel frames fully carrying the load of worktops.. Its superior strength is combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame shall be constructed from a rectangular pipe with a cross section of 60mm x 30mm and shall be 2 mm thick and shall be without a vertical front leg to give a clean look. The C-frame legs shall be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient shall be well adjusted throughout the length of table and shall have horizontal supports for drainage systems. The structure shall have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. The C-frame shall be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths shall be 620 mm, 770 mm and 920 mm for wall side and 1540mm, 1840mm for Island tables. The Corner Units shall fit well with 770mm & 920mm table depths. All frame-work is to be pre-treated with superior pure epoxy powder coated finish. R.H. 900 Ht.C-Frame Assy. For Table Depths 770 Wall Side Without Upright , 1540 Island Without Upright & 920 Wall Side With Upright |
| 5 | Providing and supply of Horizontal Members : These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800. 1050 Module Length Horizontal Members |
| 6 | Providing and supply of Horizontal Members : These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800. 1200 Module Length Horizontal Members |
| 7 | Providing and supply of Horizontal Members : These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800. 1500 Module Length Horizontal Members |
| 8 | Providing and supply of Horizontal Members : These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800. 600 Module LengthHorizontal Members |
| 9 | Providing and supply of Horizontal Members : These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800.750 Module LengthHorizontal Members |
| 10 | Providing and supply of Horizontal Members : These shall be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They shall be made of CRCA MS and coated with pure epoxy powder. These connect two C-Frames together as shown using C-clamps/U-clamps. Together with the C-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent C-Frames. They shall be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800. 900 Module Length Horizontal Members |
| 11 | Providing and supply of Panels: All other panels used as End cover of the tables in case of Island tables and wall tables to cover the space between two tables or between the table and the wall. The cover panels to be made of 1.0 mm thick CRCA sheet as per IS Code 513:1994, 770 Depth Wall Side Without Upright End Cover Panel |
| 12 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 1050 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module |
| 13 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 1500 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module + 6 Module |
| 14 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 600 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module |
| 15 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 750 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module |
| 16 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. 900 Module Length Single Side Electrical Trunking - Cutouts: 6 Module + 6 Module |
| 17 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. Outer Cover For Single-Sided Electrical Trunking |
| 18 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. Fixed Type Reagent Shelf (Add On Type) 1200 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only) |
| 19 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. Fixed Type Reagent Shelf (Add On Type) 1500 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only) |
| 20 | Providing and supply of Electrical Trunking : Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking shall be made from 1.0 mm thick CRCA MS panel. It shall be available in both, single sided and double sided configurations. It shall be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. Fixed Type Reagent Shelf (Main Type) 1500 L- Cutout : 6 Module + 6 Module (Total 2 Cutouts Only) |
| 21 | Providing and supply of Welded Cabinets : Under bench Suspended cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. TheMOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk.Finish: Powder coating pure epoxy, thickness 40-50 micronsHandle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit),Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm, Welded cabinet 900 mm(W) |
| 22 | Providing and supply of Welded Cabinets : Under bench Suspended cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. TheMOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk.Finish: Powder coating pure epoxy, thickness 40-50 micronsHandle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit),Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm, Welded cabinet 450mm(W) |
| 23 | Providing and supply of Welded Cabinets : Under bench Suspended cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. TheMOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk.Finish: Powder coating pure epoxy, thickness 40-50 micronsHandle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit),Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm,Welded cabinet 750mm(W) |
| 24 | Providing and supply of Welded Cabinets : Under bench Suspended cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. TheMOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk.Finish: Powder coating pure epoxy, thickness 40-50 micronsHandle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit),Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm, Welded cabinet 600mm(W) |
| 25 | Providing and supply of Welded Cabinets : Under bench Suspended cabinets shall be flush face construction with doors and drawers in the same plane as the cabinet face frame, without overlap. TheMOC: MS CRCA: IS – 513 (1994). Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel shall be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel shall be of 0.8mmthk.Finish: Powder coating pure epoxy, thickness 40-50 micronsHandle: Anodized Aluminium Finish handles (D-Type or Recess-Type) Lock: Units have a locking facility with 180 deg. and 10 lever cam lock mechanism (except for sink and corner unit). Hinge: SS 304 knuckle barrel Hinge of thickness 2.5mm and opening angle 180 deg. Screw: SS 304. Ball Slide: High quality double extension drawers of 500mm Length (approved Make) (required only for drawer unit),Shutter is of twin type construction with sound dampening effect using profeel. Shutter cover is equipping with Bump on for sound dampening. Depth of the cabinets: 530mm, Welded cabinet 750mm(W) single door |
| 26 | Providing and supply of Sink, Faucets & Accessories : Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise. Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D) |
| 27 | Providing and supply of Sink, Faucets & Accessories : Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise.3 Way Water Faucet Bench Mounted, 8\"\" Swing Gooseneck Model No. 100/32 |
| 28 | Providing and supply of Sink, Faucets & Accessories : Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise.Anti-Siphon Bottle Trap Model : S 04 Make: Premier |
| 29 | Providing and supply of Sink, Faucets & Accessories : Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise.Flexible/F Serated Connector Model : Hp 01 Make: Premier |
| 30 | Providing and supply of Granite Work Top : It shall be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop shall be chamfered and smoothened. The bottom of the worktop shall be polished and there shall be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk |
| 31 | Providing and supply of Granite Work Top : It shall be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop shall be chamfered and smoothened. The bottom of the worktop shall be polished and there shall be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. 6MM Self Adhesive Natural Rubber Strip |
| 32 | Providing and supply of Granite Work Top : It shall be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop shall be chamfered and smoothened. The bottom of the worktop shall be polished and there shall be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. SiliconSealant - Black |
| 33 | Providing and supply of Granite Work Top : It shall be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop shall be chamfered and smoothened. The bottom of the worktop shall be polished and there shall be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. Masking Tape |
| 34 | Providing and supply of Electrical accessories, 16A, 1 Way Switch |
| 35 | Providing and supply of Electrical accessories, 6 Module Plate - Model |
| 36 | Providing and supply of Electrical accessories, 6/16A, 6 Pin Shutter Socket - |
| 37 | Providing and supply of Electrical accessories, Almirah with Cloths Hanging Provision |
| 38 | Glass Door Storwel shall have an overall size of916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The glass door storwel shall have a brass handle and a 2 way locking mechanism with shooting bolt. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. The product shall have GREENGUARD By UL Certification |
| 39 | Vertical Filing Cabinets whcih use less floor space. Size of 4 Drawer VFC shall be 1320mm(H) X 470mm(W) X 620mm(D). All the components shall be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle shall be integrated into Metal Drawer for easy pull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ / ‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System shall be provided alongwith Shooting Bolt Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer is opened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide shall be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular plate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to back should also be available. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). |
| 40 | Supply and installation stool with following specification:-The seat shall be made up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be Diameter 40.0 cm and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available in synthetic leather. The dimensions of Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density = 45 +/-2 kg/m3and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The manual height adjustment shall be very easy to operate with a help of a knob. It should be easily locked at the most comfortable position. The five-prong pedestal shall be fabricated from 0.2 ± 0.02 cm thick HR sheet ( IS : DD 1079/HR ), powder coated ( DFT 40-60 microns ) and shall be fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The Pedestal shall be 55.0±0.5cm pitch-circle-diameter(65.0±-1.0cm with castors), Circular-foot-ringof dia 52.0±0.2cm shall be made up of dia 1.9±0.2 x0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool.The twin wheel castors shall be injection moulded in Black Nylon. Overall dimensions shall beWidth- 65.0cm, Depth- 65.0 cm, Height- 88.0 to 99.5 cm, Seat Height- 67.0 to 78.5 cm. |
| 41 | Supply and installation stool with following specification:-The seat and back shall be made from 1.2 ±0.1cm thk. hot pressed plywood and shall be upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam shall bedesigned with contoured lumbar support for extra comfort. The dimensions of seat shall be45.0cm(W) x 42.0cm.(D) and of back shall be 40.0cm(W) x 47.0cm.(H). The seat and back covers shall be injection moulded in black Co-polymer Polypropylene. The HR polyurethane foam shall bemoulded with density.=45±2.kg/m3and hardness load 16±2 kgf as per IS:7888.for 25% compression. The one-piece armrests are injection moulded from black Nylon. The armrests are fitted to the seat with armrest connecting brackets made of 0.5± 0.05 em. thk. HR steel.The permanent contact mechanism shall be designed with 360° revolving type, 14±2°maximum back tilt only, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal shall be 62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall beSeat Height - min 43.0 to max 54.0cm, Height - min87.5 to max 98.5cm, Width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm. |
| 42 | Supply and installation stool with following specification:-Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area.The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm.The chair seat & back size are*SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression.ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:· 360° revolving type.· 3 position locking with anti shock mechanism.· Tilt tension adjustmentPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors).TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.WIDTH (W): 76.1 CM.DEPTH (D): 76.1 CM.HEIGHT (H): 101.5 - 111.0 CM.SEAT HEIGHT (SH): 44.5 - 54.0 CM.Certification: Product should have BIFMA level 2 Certificate |
| 43 | Supply and installation of WORKSTATIONS with following specification- 1200mm x 600mm Providing and placing Panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht – 1200mm including powder coated aluminium trims. Tiles: Combination of top tiles are prelam tile(back side). Bottom tiles - Plain metal. SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric tackable along with split white board. INTERMEDIATE BLOCKS Intermediate blocks are given in DL + DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. Pedestals with legs - Free Standing Pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors. The product shall be greenpro, greenguard by ul, bifma level 2 and indoor advantage gold certified. The certificates should be available on official website of the respective certificate. KBPT with mousetray - metal Note: All partitions and side panels should have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. The product shall have BIFMA Level Certification and GREENGUARD by UL Certification. WISH WORK STATION PENTA FOR STAFF ROOM |
| 44 | Supply and installation of WORKSTATIONS with following specification- 1200mm x 600mm Providing and placing Panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht – 1200mm including powder coated aluminium trims. Tiles: Combination of top tiles are prelam tile(back side). Bottom tiles - Plain metal. SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split fabric tackable along with split white board. INTERMEDIATE BLOCKS Intermediate blocks are given in DL + DL finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. Pedestals with legs - Free Standing Pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors. The product shall be greenpro, greenguard by ul, bifma level 2 and indoor advantage gold certified. The certificates should be available on official website of the respective certificate. KBPT with mousetray - metal Note: All partitions and side panels should have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. The product shall have BIFMA Level Certification and GREENGUARD by UL Certification. WISH WORK STATION RECTA FOR REPORTING ROOM |
| 45 | Supply and installation of (2100 X 1150 X 740)mm Work top-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Access panels provided with soft closing hinges.Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction.Wire Management-Bottom cabinet with door is provided for flow of wires and cables. Cutout provision belowAccess flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg. HDMI,VGA-A,etc). |
