|
| 1 | Sub-Head : Concrete Work |
| 2 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland/Portland Slag cement, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the Engineer-in-charge; for the following grades of concrete. |
| 3 | Note : Extra cement upto 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. |
| 4 | All works above plinth and upto floor V level : |
| 5 | Concrete of M25 grade with minimum cement content of 300 kg /cum |
| 6 | Sub-Head : Masonry Work |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 8 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 9 | Sub-Head : Cladding Work |
| 10 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: |
| 11 | (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. |
| 12 | (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. |
| 13 | (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. |
| 14 | The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approvedshop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 15 | Sub-Head : Woodand P.V.C. Work |
| 16 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. |
| 17 | Float glass panes |
| 18 | 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). |
| 19 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 20 | 100X58X1.90 mm |
| 21 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 22 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 23 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 24 | 150x10 mm |
| 25 | Providing and fixing Stainless Steel tower bolts with necessary screws etc. complete : |
| 26 | 250x10mm |
| 27 | Providing and fixing Stainless steel handles, with necessary screws etc. complete : |
| 28 | 125mm |
| 29 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 30 | 125 mm |
| 31 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 32 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. |
| 33 | 30 mm thick plain PVC door shutters. |
| 34 | Sub-Head : Steel Work |
| 35 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 36 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 37 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. |
| 38 | 10 x 120 mm |
| 39 | Sub-Head : Roofing |
| 40 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 41 | 110 mm diameter |
| 42 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 43 | Single pushfit Coupler : |
| 44 | 110mm |
| 45 | Single tee with door |
| 46 | 110x110x110 mm |
| 47 | Bend 87.5° |
| 48 | 110 mm bend |
| 49 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 50 | 110 mm |
| 51 | Sub-Head : Finishing |
| 52 | 12 mm cement plaster of mix : |
| 53 | 1:4 (1 cement: 4 fine sand) |
| 54 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 55 | 1:6 (1 cement: 6 fine sand) |
| 56 | Lettering with black Japan paint of approved brand and manufacture |
| 57 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 58 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 59 | One or more coats on old work. |
| 60 | French spirit polishing : |
| 61 | One or more coats on old work. |
| 62 | Sub-Head : Repairs to Buildings |
| 63 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge. |
| 64 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 65 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 66 | Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm). |
| 67 | Repairs to door / windows shutter (Area upto3 sqm) including taking out and refixing the same and replacement of hinges with screws wherever required etc complete |
| 68 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : |
| 69 | Two or more coats on old work |
| 70 | Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in- charge. |
| 71 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge. |
| 72 | (a) Internal Work- Exposed on wall |
| 73 | Cleaning of drainage manholes and sewer lines by removing the deposited and other rubbish from the manholes and cleaning the sewer lines by rodding and flushing with water as directed by the Engineer -in- charge. (Rate per One manhole and sewer line to next manhole) |
| 74 | Cleaning of ceramic tile flooring / dado by rubbing with scrubbers, using mild acid and detergent powder complete as directed. |
| 75 | Mechanical cleaning of Septic Tank by using mechanical cleaning machine by suction, pumping, vaccum cleaning and removing all the waste liquid and sludge from the septic tank and disposing the waste at Municipal dumping ground. The rate includes all mechinery and workmen required and all incidental charges during pumping, filling, transporting etc complete as directed by the Engineer-in-charge. |
| 76 | Removal of deposited sludge from Septic tank by diluting the sludge with plenty of water and using a Mechanical hydraulic suction machine, pumping, vaccum cleaning and removing all the waste liquid and sludge from the septic tank and disposing the waste at Municipal dumping ground. The rate includes all machinery and workmen required and all incidental charges during pumping, filling, transporting etc complete as directed by the Engineer-in-charge. |
| 77 | Sub-Head : Dismantling and Demolishing |
| 78 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 79 | Of area 3 sq. metres and below |
| 80 | Sub-Head : Sanitary Installations |
| 81 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : |
| 82 | W.C. pan with ISI marked white solid plastic seat and lid. |
| 83 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 84 | Flexible pipe |
| 85 | 32 mm dia |
| 86 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 87 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 88 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 89 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 90 | Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. |
| 91 | Repairs to wooden / Aluminium door,window by removing & refixing after attending necessary repairs including scews,nails & other accessories required for smooth functioning of door and as per the directions of Engineer-in-charge. |
| 92 | Removing the damaged sanitary and water supply fittings and replacing them with new fittings including necessary white lead/ lead wool etc complete as directed by the Engineer - in - charge. |
| 93 | P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete - 10 litre capacity - White. |
| 94 | Unplasticised PVC connection pipe 15 mm nominal dia and 45 cm long with brass unions : |
| 95 | PTMT bib cock 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. of approved quality and colour. |
| 96 | PTMT pillar cock 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. of approved quality and colour . |
| 97 | PTMT stop cock 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. of approved quality and colour. |
| 98 | Sub-Head : Water Supply |
| 99 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 100 | 20 mm nominal outer dia. Pipes. |
| 101 | 25 mm nominal outer dia .Pipes. |
| 102 | 40 mm nominal outer dia. Pipes. |
| 103 | Providing and fixing CPVC ball valve of approved make for CPVC pipe lines. |
| 104 | 25mm dia |
| 105 | 40 mm dia |
| 106 | Providing and fixing CPVC unions for CPVC pipe line including cutting and fixing. |
| 107 | for 25mm dia pipe line |
| 108 | 40 mm dia |
| 109 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 110 | Providing and fixing Stainless Steel grating 0.60mm thick grating for floor traps complete as directed. |
| 111 | 100mm dia Circular |
| 112 | Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms. |
| 113 | Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40 gms. |
| 114 | Cutting holes up to 30x30 cm in walls including making good the same: |
| 115 | With common burnt clay F.P.S. (non modular) bricks. |
| 116 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 117 | Providing and fixing Brass NRV with handle in CPVC pipe line etc complete of approved quality: |
| 118 | (a) 40 mm diametre |
| 119 | Providing and fixing CPVC brass MTA in CPVC pipe including cutting the pipe etc complete as per direction of Engineer-in-charge. |
| 120 | (a) 40 mm diametre |
| 121 | Sub-Head : Aluminium Work |
| 122 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 123 | For fixed portion |
| 124 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 125 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). |
| 126 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 127 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. |
| 128 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 129 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 130 | Upto 5mm depth and 5 mm width |
| 131 | Sub-Head : NEWTECHNOLOGIES AND MATERIALS |
| 132 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. |
| 133 | Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). |
| 134 | 12 mm average thickness. |
| 135 | Sub-Head : Miscellaneous Works |
| 136 | Engaging labour for miscellaneous works such as cleaning of open surface drains of any size, roof, terrace, chajjas at any floor including removal of debrishes, sullage and disposal within a lead of 50 metre all complete as per direction of Engineer-in-charge. |
| 137 | Providing and fixing double scaffolding system on the exterior side upto seven storey height made with best quality bamboo ballies 1.5 m centre to centre, horizontal and vertical ballies joining with best quality coir ropes, 38 mm thick local hard wood planks for working platform and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc complete as per direction of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment. The payment will be made once irrespective of duration of scaffolding. |
