Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Schedule \"A\" Part-I (B/R itmes)Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer–in–Charge. |
| 2 | Material and labour rough cast plaster 15 mm thickin cement motar 1:4 complete as specified in SSR Part–I, clause 14.22 shall consisting of following:– firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer–in–Charge. |
| 3 | Material and labour rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer–in–Charge. |
| 4 | Material and labour rendering 15mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer–in–Charge. |
| 5 | Material and labour rendering 05 mm thick on any faces of brick work or concrete ceiling surfaces in cement mortar 1:3 andfinished even and smooth without using extra cement complete all as specified and as directed by the Engineer–in–Charge. |
| 6 | Material and labour for preparation of new plastered /concrete surface of wall applying of two coats of cement base paint over a coat of primer complete all as specified and directed. |
| 7 | Material and labour for preparation of new plaster surface on walls and applying two coats of acrylic distemper over a coat of alkali resistant primer over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces complete all as specified and as directed. |
| 8 | Material and labour for preparation of new plastered surface of ceilling applying three coat white wash complete all as specified and directed. |
| 9 | Material and labour preparation of old decorated brick/concrete, plastered /unplastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on the walls, pillars, cornices etc. up to height of triple storey bldg, including necessary scaffolding etc complete all as specified and as directed by the Engineer–in–Charge. |
| 10 | Material and labour complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, washing down with water to remove loose particles etc and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre per 10 Sqmincluding 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces up to height of triple storey bldg, including necessary scaffolding etc complete all as specified and as directed by the Engineer–in–Charge. |
| 11 | Material and labour preparation of old wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer–in–Charge. |
| 12 | Material and labour preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer–in–Charge. |
| 13 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer–in–Charge. |
| 14 | Material and labour 25 mm thick PCC 1:2:4, type B–0 as in sub base floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engr–in–charge. |
| 15 | Material and labour for black granite (of any type) tiles 16–18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types over 15mm thick screed bed in CM 1:6 and including rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations and including making holes for gas pipes or WHB outlet /inlet complete all as specified and directed. |
| 16 | Material and labour non–skid ceramic coloured tiles joint free premium/1st quality (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed by the Engineer–in–Charge. |
| 17 | Material and labour glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/ skirtings /dados of size 300 x 600 x 7 to 8 mm thick or nearest size as required, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer–in–Charge. |
| 18 | Material and labour vitrified ceramic light shade tiles premium/1st quality 9-10mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but n.exc. 0.42 sqmin floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed by the Engineer–in–Charge. |
| 19 | Material and labour vitrified ceramic light shade tiles premium/1st quality 9-10mm thick of same description as of floor tiles as in serial item No 19 above but 100 to 150mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer–in–Charge. |
| 20 | Material and labour machine cut kota stone slab18 to 22 mm thick of size not less than 550mm x 550mm in floor, set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge. |
| 21 | Material and labour machine cut kota stone slab18 to 22 mm thick ( kota stone shall be cut from size not less than 550mm x 550mm) in skirting , set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 10 mm thick renderingin CM 1:4 complete all as specified and as directed by the Engineer-in-Charge. |
| 22 | Demolition of cement concrete (un–reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer–in–Charge. |
| 23 | Material and labour 100 mm thick PCC 1:4:8 Type D–2 using 40mm graded crushed stone aggregate as in sub base of floor/ hard standing etc and finished even and fair without using extra cement complete all as specified and as directed by the Engineer–in–Charge. |
| 24 | Material and labour providing 50 mm thick cement concrete 1:3:6 type C–1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (not exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed by the Engineer–in–Charge. |
| 25 | Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand with grey cement and no pigments complete all as specified. |
| 26 | Material and labour plain cement concrete 1:2:4 type B–1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork for rough finished surfaces of concrete complete all as specified and as directed by the Engineer–in–Charge. |
| 27 | Supply and fixing as in repair water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including dismantling of water tanks and removing to store all as specified in SSR Part–I complete all as specified and as directed by the Engineer–in–Charge. |
| 28 | Supply and fixingas in repair 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)triple layer body, 100% UA stabilised, rust proof, hoisted and fixed in position all as specified in SSR Part-I including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe and fixed (minimum weight-210 gram) complete all as specified and as directed by the Engineer-in-Charge. Note : Water storage tank shall be White in colour. |
| 29 | Supply and fixing in repair PTMT grating doom 100 mm dia (Min wt 25 gms) complete all as specified and as directed by the engineer-in-charge. |
| 30 | Supply and fixing in repair PVC water closet seat cover,white,closed pattern with flat bottom ,mild steel chromium plated or aluminised hinging device complete all as specified and as directed by the engineer-in-charge. |
| 31 | Disconnecting existing water tanks of capacity 500 ltr setting aside (or lowering if required) & cleaning and removing all scale and dirt etc from in side of PVC/RCC tanks and mouths of circulating pipe & writing date on cleaning on the tank with synthetic enamel paint not less than 200mm long and 20 mm wide of words and reconnecting and refixing of the tank in position to make it operational, complete, all as specified and as directed by the Engineer-in-charge. Note :- (i) The unit rate shall be included cost of small fittings such as elbow, socket, reducer, tee, union, etc (ii) The whole process of reconnecting and refixing in position after cleaning/after carrying out water proofing treatment shall be done on the same day to ensure uninterrupted water supply to the occupant, if failing so, Rs 200/- shall be deducted for each tank per day from the contractor due. |
| 32 | Supply and fixing for galvanised iron tubing 20mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors , including taking down of existing unserviceable GI tubing including all fittings etc complete all as specified and as directed. |
| 33 | Supply and fixing for galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors , including taking down of existing unserviceable GI tubing including all fittings etc complete all as specified and as directed. |
| 34 | Supply and fixing 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 35 | Supply and fixing 15mm bore cast copper alloy chromium plated angular stop valves with capstan head, screwed down, high pressure screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 36 | Supply and fixing fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 37 | Supply and fixing bib taps 15mm bore fancy type brass chromium plated with long body, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 38 | Supply and fixing PVC connections 15 mm size with PTMT nuts of length 450 mm as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 39 | Supply and fixing vitreous china wash hand basin white, flat back of size 550mm x400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 40 | Supply and fixing as in repair brass chromium plated shower rose 100mm size swivel type with arm of standard size as per site suitable for 15mm bore pipe complete all as specified and as direced by the Engineer–in–charge. |
| 41 | Supply and fixing vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 42 | Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including water closet pvc seat cover white closed pattern with flat bottom and cover including making connections and fixed in position as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 43 | Supply and fixing mild steel chromium plated hand shower (health faucet ABS body) suitable for 15mm dia pipe with 8 mm dia 1.25 mtr long flexible tube and ABS wall hook including making connection as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 44 | Supply and fixing 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connectionSupply and fixinglush pipes for WC as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 45 | Supply and fixing as in repair vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe) but including brass chromium plated spreader, PVC waste pipe, providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed by the Engineer–in–Charge. |
| 46 | Supply and fixing 20 mm bore Gun–metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 47 | Supply and fixing as in repair, brass chromium plated WHB mixer swan neck for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer–in–Charge. |
| 48 | Supply and fixing CP brass wall mixture 3–in–1 system for mixing hot and cold water suitable for 15mm bore pipe complete with 115 mm long bend pipe, connecting legs & wall flange and wall bracket for hand shower as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 49 | Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer–in–Charge. |
| 50 | Supply and fixingsinks with drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 915mm x 460mmwith bowl size 410mm x 330mm x 160mm as in repaircomplete all as specified and as directed by the Engineer-in-Charge. |
| 51 | Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engr–in–charge. |
| 52 | Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engr–in–charge. |
| 53 | Taking down shutters of any description area exc 1.00 sqm andnot exc 2 sqm each complete all as specified and as directed by the Engineer–in–Charge. |
| 54 | Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and refixing in the same opening complete all as specified and as directed by the Engineer–in–Charge. |
| 55 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 56 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed. |
| 57 | Supply and fixing bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by the Engineer-in-Charge |
| 58 | Cutting holes in exc. half brick but not exc. one brick thick walls, built in mud mortar, for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall) complete all as specified and as directed by the Engineer-in-Charge |
| 59 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed by the Engr–in–charge. |
| 60 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) glazed and skeleton shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed by the Engr–in–charge. |
| 61 | Material and labour rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixingconforming to Fe–410–W (Grade E–250) quality \"A\" complete all as specified and as directed by the Engineer–in–Charge. |
| 62 | Supply and fixing powder coated aluminium section (minimum thickness of powder coating 50 micron) for frame and shutters of doors, windows (fixed, sliding, hangung) & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer–in–Charge.Note : (a). Glazing shall be measured and paid separately.(b).Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured.(c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight.(d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed. |
| 63 | Supply and fixing powder coated anodised aluminium grill (anodized transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to thewindow frame with C.P brass/ stainless steel screws @ 200 mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, complete all as specified and as directed by the Engineer–in–Charge. |
| 64 | Supply and fixing stainless steel butt hinges 100mm long medium weight complete all as specified and as directed by the Engineer–in–Charge. |
| 65 | Supply and fixing 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer–in–Charge. |
| 66 | Supply and fixing 200 mm long aluminium handle fabricated type anodised complete all as specified and as directed by the Engineer–in–Charge. |
| 67 | Supply and fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and as directed by the Engineer–in–Charge |
| 68 | Supply and fixing 300mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer–in–Charge. |
| 69 | Supply and fixing aluminium (Diecast) body hydraulically door closer regulated, designation No. 3, universal type, suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg complete all as specified and as directed by the Engr–in–charge. |
| 70 | Supply and fixing for 65 mm size long mortice lock vertical type, 2 levers with key in duplicate, mild steel body fixed in shutters with screw complete all as specified and as directed by the Engineer–in–Charge |
| 71 | Supply and fixing double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty fixed complete all as specified and as directed by the Engineer–in–Charge |
| 72 | Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr–in–charge. |
| 73 | Material and labour brick work with sub class \"B\" old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer–in–Charge. |
| 74 | All as per serial item No.73 here in before but except bricks old servicable bricks obtained from serial item No 72 above including removing mortar,cleaning the bricks with water, complete all as specified and as directed by the Engineer–in–Charge. |
| 75 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer–in–Charge. |
| 76 | Material and labour sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer–in–Charge. |
| 77 | Supply and fixing 3mm thick frosted sheet glass ordinary type and glazing with aluminium beading, rubber packing or oil putty in square n exc 0.5 sqm each pane complete all as specified and directed. |
| 78 | Material and labour sheet glass 4.8mm thick tinted quality and glazing with aluminium snap beading, rubber gasket in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer–in–Charge. |
| 79 | Material and labour 12mm thick prelaminated particle board interier grade (grade–1) confirming IS 14587 prelaminated both side with decorative choice lamination and fixed to aluminium door shutter with glazing clips, rubber complete all as specified and as directed by the Engineer–in–Charge. |
| 80 | Supply and fixing galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised mild steel wire staple complete all as specified and as directed by the Engineer–in–Charge. |
| 81 | Supply and fixing galvanised mild steel wire cloths 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed to steel/wooden /aluminium window/ frame with tinned tacks or galvanised mild steel wire staple as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 82 | Demolition and breaking up drain pipes or rainwater pipesor SWR pipe or (any size or pattern), including all fittings, heads, shoes, bends, swan–necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engr–in–Charge. |
| 83 | Supply and fixing 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor or fixed to wall complete all as specified and as directed by the Engineer–in–Charge. |
| 84 | Supply and fixing 110mm bore PVC (SWR) bends of any radius complete all as specified and as directed by the Engineer–in–Charge. |
| 85 | Supply and fixing 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor or fixed to wall complete all as specified and as directed by the Engineer–in–Charge. |
| 86 | Supply and fixing 75mm bore PVC (SWR) bends of any radius complete all as specified and as directed by the Engineer–in–Charge. |
| 87 | Material and labour 75mm bore PVC (SWR) floor trap with grating including jointing with solvent cement including fixed in cement concrete as in repair complete all as specified and as directed by the Engineer–in–Charge |
| 88 | Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by the Engineer–in–Charge. |
| 89 | Demolition of mud in roofs, any thickness, including plastering and leeping (whethere full thickness removed or only a part thereof) including removing old tar felt, all loose dirt, cement plaster, cleaning the concrete surface including removal & cleaning of vegetation, fungus, moss, small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work complete all as specified and directed by EIC |
| 90 | Material and labour for providing cement concrete 1:2:4 Type B1 using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, padding, rounded or chamfered on edges including from work where ever required complete all as specified and as directed by the Engineer–in–Charge. |
| 91 | Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at theside and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture\"s instructions. The vital physical and chemical parameters of the membrane shell be under :–(i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms(ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147)(iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane onlycomplete all as specified and as directed by the Engineer–in–Charge.(iv)The work shall be carriout at a height upto 12 metre. |
| 92 | Material and labour cement concrete tiles 20 cm x 20cm x 20 mm thick, machine pressed laid on and including screed bed 15 mm thick in cement mortar 1:6 and joints grouted and pointed flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed, complete all as specified and as directed by the Engineer–in–Charge. |
| 93 | Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated fromfollowing sections :–(a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces.(b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leafof T – section20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf.(c) Vertical mullion shall be ERW hollow T –section of size 60 x 25 mmmade from 1.25 mm thickMS sheet(d) The above steel window shall be deemed to include the following accessories/ fittings :i)Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape– 04 Nos per windowii)Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.iii) MS tower bolt stove enamelled 150mm long– 2 Nos per leaf.iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf.(v) Cleat 55 mm long of solid square 15x20x.63mm square – 01 No per leafvi)Pintal hinges 12 x 75 mm – 2 Nos each leafvii) 10mm square Guard bar @ 10 cm c/c welded to frame.(viii) Two coat of Synthetic enamel paint over one coat of red oxide primer.(ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws.(x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window.(xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B–1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit.(ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above.(iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type. |
| 94 | Supply and fixing 32/40mm dia PVC waste pipe of standard length for wash hand basin /Kitchen sink etc as in repair complete all as specified and as directed by the Engineer–in–Charge. |
| 95 | Supply and fixing as in repair stainless steel curtain rod 25mm dia having wall thickness 1.00mm with and including stainless steel decorative brackets, two lotto for each rod length at both end etc fixed with stainless steel screws complete all as specified and as directed by the Engineer–in–Charge. |
| 96 | Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and as directed by the Engineer-in-Charge. |
| 97 | Supply and fixingPre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 grams per Sqm (Az 150) of any colour having tensile strength of 550 Mpaas in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge. |
| 98 | Supply and fixingPre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150grams/Sqm (Az-150)as in roof ridge,valley gutter etc fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge. |
| 99 | Dismantling wooden scantling40 sqcm and over in section in framed work in positioncomplete all as specified and as directed by the Engineer-in-Charge. |
| 100 | Supply and fixing rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe-410-W (Grade E-250) quality B complete all as specified and as directed by the Engineer-in-Charge |
| 101 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets/ aluminium partion/cabinets any thickness including cover fillets and false ceiling frame workcomplete all as specified and as directed by the Engineer–in–Charge. |
| 102 | Material and labour for PCC 1:5:10 type E–2 using 40mm graded crushed stone aggrgate as in filling in sunken portion floor, rounded or chamfered on edges including demolition and removing from site complete all as specified and directed. |
| 103 | Material and labour for preparation of old treated surfaces of walls, cornices etc. (plastered or unplastered) by brooming down, steel wire brushing, scraping down smoke soot, moulds, moss, efflorescence salts, trading oil and greasy spots etc, up to any height ofincluding necessary scaffolding and applying one coat of acrylic distemper on wall surface etc., complete, all as specified and as directed |
| 104 | Material and labour for complete removal of existing surfaces of walls, cornices etc. (plastered or unplastered) by brooming down, steel wire brushing, scraping down smoke soot, moulds, moss, efflorescence salts, trading oil and greasy spots etc, up to any height ofincluding necessary scaffolding and applying two coat of acrylic distemper over and including 2 mm thick wall care putty on wall surface etc., complete, all as specified and as directed |
| 105 | Material and labour for preparation of old wooden painted surfaces and applying one coats of synthetic enamel painton wooden surfaces of any description, not otherwise described, over 10cm width or girth complete all as specified and as directed. |
| 106 | Material and labour preparation of old paintedsteel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed by the Engineer–in–Charge. |
| 107 | Material and labour for providing reinforced cement concrete type B–1, 1:2:4 (20mm graded crushed stone aggregate) in roof slab, landings, balconies, canopies, deck slabs and in shelves, man hole cover and the like complete with joints to match including demolition of old RCC complete all as specified and directed |
| 108 | Formwork to fair finish soffits of suspendedslabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick complete all as specified and directed |
| 109 | Supply and fixing mild steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0,.9mm dia or screwing with clip etc all as specified. |
| 110 | Material and labour applying a coat of solar reflective aluminium paint @ 0.11 kg per sqm on APP membrane surfaces complete all as specified and as directed by the Engineer-in-charge. |
| 111 | Dismentling of mild steel work of any description, complete, all as specified and as directed |
| 112 | Material and labour for sunken floor water proofing treatment complete all as under :–(A) Scrapping the surface with wire brush and cleaning with water and allow to dry.(B) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound.(C) 15 mm thick cement plaster 1:3 mixed with water proofing compound as per manufacture instruction (the corner will made rounded in concave shape).(D) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound.(E) Apply one coat of hot bitumin grade 85/25 conforming to IS 702 @ 1.2 kg/sqm.(F) Supply and laying APP with non woven polyster reinforced sheet 3mm thick weight not less than 3.00 kg/sqm.(G) Applying one coat of hot blown bitumin grade 85/25 conforming to IS–702 @1.20 kg/sqm.(H) Curing the sunken portion with water min 48 hours by ponding.(J)Fixing 50mm bore GI pipe medium grade as in spout of 0.60 mtr length in each sunken. |
| 113 | Supply and fixingmild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate including fixing to steel frame complete all as specified and directed. |
| 114 | Supply and fixingball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed |
| 115 | Providing and laying of300x300 mm & 10mm thick Anti-Skid pavement tile Endura vetrified tile in approved color & Shade and in anti skid finishset and jointed in neat cement slurry and pointed in white cement & pigment to match over and including 15 mm thick screed bed in cement mortar 1:6 and complete all as specified and directed |
| 116 | Supply and fixing 5mm PVC hollow sheet (the thicknees of inner wall 0.7 to 1.00mm) in wall panelling inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified and as directed by the Engineer–in–Charge |
| 117 | Supply and fixing 18mm thick WPC board (Minimum density 600kg/Cum) of single side rigid lamination of approved colour and other side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen cabinet/cub boardshutters and shelves complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge. |
| 118 | Supply and fixing 18mm thick WPC board (Minimum density 600kg/Cum)both side plain white colour fixed with stainless steel screws, solvent cement /adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed byEngineer-in-Charge. |
| 119 | Supply and fixing for D type cabinet handles premium quality, stainless steel grade 304, gloss chrome, SN finished 150 mm long matt finished coplete all as specified and directed by Engr-in-charge. |
| 120 | Supply and fixingfor stainless steel 304 grade wire basket (average weight 2.5 to 4 Kg per Basket) of pull out type like plain /cup & saucer /bottle /multi purpose /2–3 shelf basket etc for kitchens of required size fixed in position complete all as specified anddirected. |
| 121 | Supply and fixing Ball bearing runners 450mm telescopic (KA4732) full extension load capacity minimum 35 Kgs coplete all as specified and directed by Engr-in-charge. |
| 122 | Schedule \"A\" Part-II (E/M itmes)Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc.,complete all as specified and as directed by the Engineer-in-Charge. |
| 123 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly(boxesshall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally) including provision of new covered plate over sunken box for housing themodular switches , modular socket outlets,modularfan regulators etc.for one light/fan/exhaust fan/bell point controlledby one way switch,complete all as specified and as directedby Engineer-in-Charge. Note :-a) All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid forseparately . |
| 124 | Description all as per serial item No.123 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 02 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. |
| 125 | Description all as per srl item No 123 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathedcable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly, complete all as specified and as directed by the Engineer-in-Charge.Note : (i) Point wiring shall be done in a manner that not more than 01 socket point executed in one circuit.(ii) Each socket point will be measured and paid as per point. |
| 126 | Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts, complete all as specified and as directedby Engineer-in-Charge. |
| 127 | Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 128 | Supplyand fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed by the Engineer-in-Charge. |
| 129 | Supply and fixing of modular socket outletmultipin combined,6 Amp, one way, two module, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 130 | Supply and fixing ofmodular socket outletmultipin combined, (6pin), 6/16 Amp, one way, two module, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 131 | Supplyand fixingas in repairelectronic Fan regulator, modular 100 watts, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep, complete, all as specified and as directed by the Engineer-in-Charge. |
| 132 | Supply and fixing in repair calling bell, ding dong, 230 volt, complete all as specified and as directed by the Engineer-in-Charge. |
| 133 | Supply and fixing ceiling rose surface type 2/3 terminalpolycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge. |
| 134 | Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directedby Engineer-in-Charge. |
| 135 | Supply and fixing in replacement LED lamp 12 wattthreaded/pin end, warm/cool lamp type as per site requirement suitable for fixing on existing batten/angular holders, completeall as specified and as directed by the Engineer-in-Charge.Cat part No. BL0212WB22 of Make Benlo or equivalent make given in Appx \"B\". |
| 136 | Supply and fixing in repair,LED batten fitting 10-12 watts, 2 feet, aluminium housing with electronic drivercool/warm typeindustrial model complete,connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINE+ BS10WLED865SPCSS of make Havells or equivalent in make given in Appx \"B\". |
| 137 | Supply and fixing in repairLED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic drivercool/warm typeindustrial model complete,connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINE+ BS20WLED865SPCSS of make Havells or equivalent in make given in Appx \"B\". |
| 138 | Supply and fixing in repair, LED surface mounted bulk head luminaries, 8-10 watts, with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. HEXAFT10WLED857SSYMBOPC of make Havells or equivalent in make given in Appx \"B\". |
| 139 | Supply and fixing in repair,9/12 watt LED light fitting heritage wall mounting fixture (sketch type) including B-22 LED lamp compact and energy efficient epoxy powder coated luminaire and connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete including removing unserviceable light fittingscomplete all as specified and as directed by the Engineer-in-Charge. Cat part No. HLWB-01-B22 of make Halonix or equivalent in make given in Appx \"B\". |
| 140 | Supply and fixingSurface/Recess mounting LED 15/18 watt cool/warm type circular down lighter/ COB panelwith PVC housing, 240 volt, 50HZ, AC supplycompletewithall accessories internally pre wiredincluding connecting with 3 coreflexible copper conductor from ceiling rose to connector of the light, including disconnecting and taking down existing old unserviceable fitting, complete all as specified and as directed by the Engineer-in-Charge. Cat part No.LDRDZ-15-C of make Orient or equivalent make given in Appx \"B\". |
| 141 | Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 20 -25 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.ENDURASUNDOWNSL25WLED765PASYBOTGIHD of make Havells or equivalentin make given in Appx \"B\". |
| 142 | Supply and fixing in repair, service bracket of mild steel pipe 25 mm bore medium grade of length 0.70 mtr fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts and washer and suitable reducer for connecting fitting to GI pipe as required at site includingtwo coats ofsynthetic enamel paintoverone coat of red oxide primer on mild steel work complete all as specified and as directed by the Engineer-in-Charge. |
| 143 | Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA \"B\" curve including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge.Cat part No.811955 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 144 | Supply and fixing as in repair modular (PVC sheet) cover plate with support frame3 ways suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engr-in-charge. |
| 145 | Supply and fixing as in repair modular (PVC sheet) cover plate with support frame 4 ways suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engr-in-charge. |
| 146 | Supply and fixing as in repair modular (PVC sheet) cover plate with support frame 6 ways suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engr-in-charge. |
| 147 | Supply and fixing as in repair modular (PVC sheet) cover plate with support frame 8 ways suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engr-in-charge. |
| 148 | Supply and fixing as in repair modular (PVC sheet) cover plate with support frame 12 ways suitable for fixing switch/socket/fan regulators etc on existing MS boxes of any make as per site requirement including removing unserviceable items, complete all as specified and as directed by the Engr-in-charge. |
| 149 | Supply and fixing GI/MS (terminal boxes) rectangular block with earth dolly duly painted internally and externally with two coats of anti corrosive paint over a coat of redoxide primer including provision of new 3 modular cover plate with support frame over sunken box fixed with brass screw and cup washer for mounting, modular switches, sockets outlets, fan regulator etc. complete all as specified and as directed by the Engr-in-charge. |
| 150 | All as per above item No. 149 but new 4 module cover plate with support frame, complete, all as specified and as directed by the Engr-in-charge. |
| 151 | All as per above item No. 149 but new 6 module cover plate with support frame, complete, all as specified and as directed by the Engr-in-charge. |
| 152 | All as per above item No. 149 but new 8 module cover plate with support frame, complete, all as specified and as directed by the Engr-in-charge. |
| 153 | All as per above item No. 149 but new 12 module cover plate with support frame, complete, all as specified and as directed by the Engr-in-charge. |
| 154 | All as per above item No. 149 but new 1 module cover plate with support frame complete all as specified and as directed by the Engr-in-charge. |
| 155 | Supply and fixing PVC connection pipe 600 mm long and 15mm dia having wire mesh coating over it with brass nuts and washers suitable for connecting geysers inlet and outlet with GI tubings including taking out old unserviceableconnections of any description all as specified and as directed by Engr-in-charge. |
| 156 | Supply and fixingas in repairheavy duty exhaust fan 300 mm sweep with corrosion resistant metallic body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, metallic base framewith rubbermountings for silent operation, 6 pole, maximum watt input not more than 55 watt, 2100 RPM,minimum air delivery 600 cum/hr with metal bladesincluding making good ofopening, cutting opening as peretc.,and shutter type louvers self-openable/ closeble for protecting the entrance of birds as per IS :2132-1967 and testing complete all as specified and as directedby Engineer-in-Charge. Cat part No 70001 of make Bajaj or equivalent make given in Appx \"B\". |
| 157 | Supply and fixingas in repairheavy duty wall mounting fan400 mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotormounted on two ball bearings, aerodynamically contoured blades, rigid frame ,1350 RPM,PVC blades andtesting complete all as specified and as directedby Engineer-in-Charge. Cat part No 250552 of make Bajaj or equivalent make given in Appx \"B\". |
| 158 | Supply and fixing of heavy duty exhaust fan 250mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, PVC base framewith rubbermountings for silent operation, maximum watt input not more than 25 watt, 1400 RPM,minimum air delivery 210 cum/hr, PVC blades and shutter type louvers self-openable/ close able for protecting the entrance of birds and testing as in repair complete all as specified and as directedby Engineer-in-Charge. Cat part No 70049 of make Bajaj or equivalent make given in Appx \"B\". |
| 159 | Note:-Amount of credit ofRs.81,084.50 for retrieved materials is mentioned in Schedule of Credit Page No. 123 & 124 of tender doCubicmetre ents in pdf form which will be deducted offline while acceptance of tender. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
