|
| 1 | PART -1 : Civil WorksProviding and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) with minimum cement content as per the latest revision of relevant IS codes including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels. |
| 2 | Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 with minimum cement content as per the latest revision of relevant IS codes using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.Note : All projections, fins etc. in the concrete surface formed at the joints in the formwork should be ground & flush and finished at no extra cost. |
| 3 | Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 with minimum cement content as per the latest revision of relevant IS codes using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications in superstructure at all levels upto 20 m above plinth level .Note : All projections, fins etc. in the concrete surface formed at the joints in the formwork should be ground & flush and finished at no extra cost. |
| 4 | Extra for providing RMC (Ready Mixed Concrete) conforming to IS : 4926 (latest) in lieu of conventional PCC/RCC items supplied by RMC plant outside BARC, Trombay premises of approved Manufacturer or approved equivalent meeting the technical specifications as per relevant codes and standards for all type of structural elements/ RCC/ PCC elements including transporting, pumping etc. complete as per instruction of the Engineer in charge. Notes: 1) The contractor shall obtain prior approval for RMC manufacturer from Engineer in Charge in writing. 2) The rate shall apply for all levels and locations including all type of structure etc. |
| 5 | Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G I binding wire of minimum 16 Gauge (Excluding PVC coating), all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Steel supplied by the contractor. Using TMT bars of Fe-550D grade or as approved of all sizes of approved make or approved equivalent meeting the technical specifications as per relevant codes and standards. TMT bars to be supplied by the contractor shall conform to IS – 1786 (Latest edition) and BARC specification Notes: 1) The contractor shall supply documentary evidence of purchase of steel, Test certificate from approved manufacturers or approved equivalent meeting the technical specifications as per relevant codes and standards and also testing third party from approved laboratories without any extra cost. 2) Binding wire required for the work will have to be supplied by the contractor at their own cost and will not be measured for payment. 3) Cover blocks shall be of same grade of concrete. |
| 6 | Providing 15 mm thick plastering using Ready mix internal plastering compound as approved for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge. |
| 7 | Providing and fixing G.I. chicken mesh in the junctions of concrete & brick work / masonry or as directed by the Engineer in charge including cutting, fixing with nails in position before plastering complete all as directed by the Engineer-in-charge. (only area of the chicken mesh used alone will be measured) |
| 8 | Providing, centering, shuttering Form work using PVC film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge.For Super-structure at all levels |
| 9 | Providing and constructing Half brick masonry using Flyash/ FlyashLime brickswith minimum 70 kg / Sq.cm. strength of approved size and approved make or approved equivalent meeting the technical specifications as per relevant codes and standards in partition walls in C.M 1:4 (using crushed sand) including scaffolding, raking out joints, curing etc. complete and with stiffners of RCC 1:2:4 (105 X 75 mm size) at every 900 mm height including form work curing etc. complete as per specifications but excluding reinforcement in Super Structure up to Floor - II level. (Reinforcement will be paid under relevant item) |
| 10 | Providing and constructing brickwork in cement mortar1:6 using crushed sand withFlyash/ FlyashLime bricks with minimum 70 kg/ Sq.cm strength of approved quality and size in super structure above plinth up to and including FloorIIlevel including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings. |
| 11 | Providing and fixing Minimum 15-17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Telephone Black colour for kitchen platforms, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels |
| 12 | Providing, supplying and fixing 98 mm overall thick partition using approved stud partition which includes one layer of tapered edge 13mm thick approved Board (conforming to BS 5234 –1992, Part 2) is screw fixed with drywall screws of 25mm at 300mm centre to centre on either side of 70mm approved \"C\" stud (0.5mm thick having one flange of 34mm and another flange of 36mm made of GI steel) placed at 600mm centre to centre in 72mm floor and ceiling channel (0.5mm thick have equal flanges of 32mm made of GI steel), which is anchored to the floor & true ceiling using suitable anchor fasteners or metal screws with nylon plugs. The boards are to be fixed to the frame work with joints staggered to avoid leakage through joints. A fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm each) has to be provided at the horizontal joints of the two boards screw fixed to the studs using metal to metal flat head screws. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with suitable & crackfree jointing compound, suitable joint paper tape having adequate strength and min. two coats of drywall top coat. 25mm glass wool slab of density of 32Kg/cu.m shall be placed in the cavity. |
| 13 | Providing and fixing brassmortise latch and lock of approved make or approved equivalent meeting the technical specifications as per relevant codes and standards with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications. |
| 14 | Providing and fixing 35 mm thickflush door shutters conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneeringwith internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete. |
| 15 | Extra for providing and fixing flush doors with decorative veneering on both sides |
| 16 | Providing and fixingFRPdoor shuttersflush door / panelled type with plain colour or wooden veneer finish of approved design and approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foamand fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws 30 mm thick panelled door type of approved colours including the cost of ISI marked 100 mm heavy quality stainless steel butt hinges with necessary screws. |
| 17 | Providing and applying wall painting two coats on new work with premium plastic emulsion paint of approved brand or approved equivalent meeting all the technical parameters as per relevant codes and standards to give an even shade, including a coat of approved cement primer, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge |
| 18 | Providing and applying white cement based wall putty of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, over concrete or Plastered surfaceup to 3 mm thickto get uniform surface free from undulationincluding cleaning complete all as directed by the Engineer-in-charge |
| 19 | Dismantlingplain cement concretemanually / by mechanical meanscarefully without damaging adjacent structures including disposal of debris within 200 m lead as per direction of Engineer-in-charge |
| 20 | Lead charges for debris lead exceeding 2 KM but not exceeding 3 KM, by mechanical transport including loading, unloading, stacking / levelling etc.Note: The rate is applicable for the NET Quantities arrived at after making deductions for voids30% in respect of debris from the corresponding stack/truck measurements. |
| 21 | Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge |
| 22 | Providing and fixing C.P brass 2 way Angle cock (2 Angle cock combinationin single fitting) of heavy quality of approved make as per specifications and as directed by the Engineer-in-charge. |
| 23 | Providing,laying , jointing, fixing and testing heavy quality ( (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm.hydraulic pressurewith a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. |
| 24 | 15 mm dia G.I pipe |
| 25 | 25 mm dia G.I pipe |
| 26 | 40 mm dia G.I pipe |
| 27 | Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/Sq.Cm. pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge |
| 28 | 25 mm n.b. |
| 29 | 40 mm n.b |
| 30 | Providing and fixing 15 mm diameter C.P brass bib cock of heavy quality of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards and as directed by the Engineer-in-charge. |
| 31 | Providing and fixing 15 mm n.b. C.P brass Angle cock of heavy quality of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge. |
| 32 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix cement plastered on both sides with cement mortar 1:3 finished with a floating coat of neat cement and making necessary channels for the drain etc. complete.For pipes of diameter ranging from 100mmto 230 mm |
| 33 | Providing, supplying, fixing in position, under floors or in walls centrifugally cast iron pipes including required specials like bends, tees, \"Y\" collars, cowl etc for soil, waste and ventilation pipes conforming to IS.3989or Cast iron hubless pipes conforming to IS : 15905 of approved quality including cost of jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer, fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site. |
| 34 | 75 mm diameter Centrifugally cast (spun) iron socketed pipe as per IS:3989 using 0.90 kg lead / joint or Cast iron hubless pipes as per IS : 15905 |
| 35 | 100 mm diameter Centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.00 kglead / joint or Cast iron hubless pipes as per IS : 15905 |
| 36 | 150 mm dia centrifugally cast (spun) iron socketed pipe as per IS:3989 using 1.20 kglead / joint or or Cast iron hubless pipes as per IS : 15905 |
| 37 | Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating ,complete all as specifications and drawings and as directed by the Engineer-in-charge |
| 38 | Providing and fixing square mouth S.W. gully trap, ofsize 150 mm x 100 mm and \"P\" type, complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design |
| 39 | Constructing brick masonry circular type manhole of internal diameter 910 mm at bottom and 560 mm diameter at top, with 230 mm brick work in cement mortar 1:4, inside and ouside & all exposed surfaces cement plaster 20 mm thick with cement mortar 1:3 finished with a foating coat of neat cement, foundation concrete of mix 1:3:6 and making necessary channel in cement concrete 1:2:4 finished with a floating coat of neat cement all complete as per standard design , fixing C.I circular manhole cover, C.I steps as per the drawing (C.I frame & cover, C.I steps and excavation work will be paid seperately under relevant Item.) For an initial depth of 910 mm |
| 40 | Extra over for depth beyond 910 mm for circular type manhole 910 mm internal diameter at bottom and 560 mm internal diameter at top, in brick work. |
| 41 | Extra for providing and fixing mirrors withapproved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, stainless steel 304 grade STUDS (with wall spacers) complete all as per specifications and as directed by the Enginner-in-charge |
| 42 | Providing and fixing stainless steeltoilet paper holderrecessed type of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standardswithS.S screws as directed by the Engineer-in-charge complete. |
| 43 | Providing and fixingheavy qualityCP brassbottle trap 31 / 32 mm ofapproved make or approved equivalent meeting all the technical parameters as per relevant codes and standards single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal,ofapproved make or approved equivalent meeting all the technical parameters as per relevant codes and standards for wash basins / urinal etc all as per specifications and directed by the Engineer in charge. |
| 44 | Providing, supplying and fixing JET spray with 1.00 metre long flexible tube connection in European / Anglo Indian closet under seat cover fixtures complete all as specified and as directed by the Engineer-in-charge |
| 45 | Providing and fixing viterious China wash basin of approved colour and approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm longPVC Inlet connection,32 mm heavy quality C.P. brass waste couplingof standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-chargeWhite vitreous China wash basin of approx. size 630 mm x 450 mmor as approved with single 15 mm C.P. brass pillar tap |
| 46 | Providing and fixing viterious China wash basin of approved colour and approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm longPVC Inlet connection,32 mm heavy quality C.P. brass waste couplingof standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-chargeWhite vitreous Chinacounter top / counter below wash basin of approx. size 560 mm x 410 mm /560 mm x 450 mm or as approved, with single 15 mm C.P. brass pillar tap (OVAL / ROUND Models) |
| 47 | Providing and fixing C.P. brass towel rail of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, 600 mm long complete fixed to walls with 30 mm C.P. brass screws with concealed fitting arrangement all as directed by the Engineer-in charge. |
| 48 | Providing and fixing of high quality Stainless steel Body Liquid Soap dispenser of cylindrical shape of approx. 51mm in diameter and approx. 180 mm in height or as approved in approved finish, shape and approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards complete fixed to walls with required fastners all as directed by Engineer in Charge. Note: Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 49 | Providing and fixing chloronated PVC(CPVC) pipes, slives having thermal stablity for hot and cold water supply (as ASTM standard 2846 and SDR -11Grade) or as outlets in cluding all cpvc plain and brass threaded fitting , fixing the pipe with clamps, including casing the wall conainselling the pipe and making good the same etc.This includes jointting of pipe and fitting with cpvc solvent sealent and testing the joints complete all as per specification,drawing and as directed by the Engineer-in charge.50mm Outer Dia CPVC Pipe (External / Open). |
| 50 | Providing and fixing mirror of superior glass of approved quality and of required shape and size with 6 mm thick Plain A.C sheet backing fixed to walls with consealed Brass C.P. Mirror screws and consealed washers etc. complete all as per specifications and as directed by the Enginner-in-Charge. |
| 51 | Providing and fixing wall mounted 15mm nominal bore Sensor faucet (Battery Operated) of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, including all necessary fittings and accessories. The work shall include cutting and making good finish in the wall, fixing of concealed body and exposed part, connection with water supply line, and testing and commissioning of the complete installation etc, complete all as per manufacturer’s specifications and as directed by the Engineer-in-Charge.Note: Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 52 | Supply and fixing sand blasted toughened glass of 12 mm for urinal parititon (approx. size 1000 mm x 450mm) of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards for partitions with crystal edge polish and necessary patch fittings hunged on wall, all joints sealed with weather silicone sealent complete all as per approved shop drawings, complete as per specifications and as directed by the Engineer-in-charge. |
| 53 | PVC Providing and fixing PVC Moulded Corner Guards, fixed with necessary Hardware complete as directed by the Engineer-in-charge. Mode of measurement: Running metre Length, No wastage to be added. |
| 54 | Providing and fixing minimum 15 mm thick gang saw cut mirror polished machine cut Artificial Granite of approved shade and quality, for flooring, kitchen platforms, vanity counters, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edge to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels. |
| 55 | Providing and laying Vitrified tiles in floor of size 600 mm x 600 mm having minimum 9 mm thickness, with water absorption less than 0.08% and conforming to IS:15622, of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, in all colours and shades,in Glossy or Matt or satin finish laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints with white cement based Tile Grout of matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge.Note : Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 56 | Providing and laying Vitrified tiles of size 1200 mm x 600 mm having minimum 9 mm thickness in skirting and riser of steps , with water absorption less than 0.08% and conforming to IS: 15622, of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards, in all colours and shades,in Glossy or Matt or satin finish, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477,in average 6 mm thickness, including grouting of joints withwhite cement based Tile Grout of matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge.Note : Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 57 | Providing and fixing rimless wall hung vitreous china water closet of approx. size 380 mm x 515 mm x 360 mm or as approved of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards with soft close Slim Seat Cover of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards with all internal fitting, fixing with heavy duty solid rocking bolt , including attached flushing cistern, testing , commissioning & cleaning etc. complete all as perdrawings and specifications and as directed at site. Note: Sample(s) shall be submitted for approval of Engineer in-Charge prior to procurement. |
| 58 | Providing and fixing C.P. brass pillar cock, 15 mm nominal bore, long‐neck type with aerator, made from copper alloy conforming to IS 8931, with heavy-duty chrome plating as per IS 1708 (minimum 10 µm nickel + 0.3 µm chromium layers), fitted with auto-closing mechanism (preset closing ≤ 12 seconds), and 65 mm extension body, suitable for water pressure up to 6 kg/cm², including necessary fittings, PTFE tape, and leak-proof joints, complete and as directed by the Engineer-in-Charge.Note : Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 59 | Providing and fixing sensor based white vitreous china urinal set of approx. size 360 mm X 350 mm X 710 mm or as approved of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards flush pipe and C.P. brass spreaders, 32mm dia Urinal waste coupling and clamp etc. including making G.I water line connection ( Only G.I./CPVC pipes will be paid under relevant Item).Note: Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 60 | Providing and fixing stainless steel movable hinged grab bar of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards (conforming to grade SS 304, satin finish) consisting of 38 mm dia. 18 SWG stainless steel pipe duly bended in required shape and size, hinged with 3mm thick stainless steel rectangular sheet of required size having 6 nos. holes and U shaped stainless steel clamp for holding the grab bar including cutting, bending welding grinding, polishing and fixing with suitable sized and nos. of dash fasteners complete as required. All bends to be neatly finished miter joints complete as per specifications and as directed by the Engineer-in-charge. |
| 61 | Providing and fixing stainless steel urinal grab bar/wash basin Grab bar of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards (conforming to grade SS 304, satin finish) consisting of 38 mm dia. 18 SWG stainless steel pipe duly bended in required shape and size, hinged with 3mm thick stainless steel rectangular sheet of required size having 6 nos. holes and U shaped stainless steel clamp for holding the grab bar including cutting, bending welding grinding, polishing and fixing with suitable sized and nos. of dash fasteners complete as required. All bends to be neatly finished miter joints complete as per specifications and as directed by the Engineer-in-charge. |
| 62 | upply & Installation of Stainless Steel 304 hand dryer of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards with brush motor, Power 1650W,Voltage AC220-240V , 50/60Hz, Operation Touch Free Infra-Red Activation, Auto Cut Off 30 Sec, Speed 25000 RPM Noise Level 80db(A), Heater Element Heating PTC Element, Air Speed 85-95 m/s, Drying Time 15 s, Motor Brush Motor, Blowing Volume 150 m3/h, Waterproof IPX1, Weight 12 Kg, category hand dryer machine complete as per specifications and as directed by the Engineer-in-charge |
| 63 | Providing and fixing SS Toilet Paper roll holder with stainless steel flap of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards completely fixed to walls with 30 mm C.P. brass screws with concealed fitting arrangement all as per specifications and as directed by the Enginner-in-Charge. |
| 64 | Providing and fixing in doors finished brass handle assembly comprising of pair of brass lever handleincluding Mortise lock of size 8” Cylinder Lock with 70 mm Brass Cylinder with pair of matching Brass door handle plate cover or equivalent products meeting technical parameter / specification of approved shade & colour, and concealed Door Closer with fixing of Brass screws including alignment and minor repairing of doors for fixing locks, handles etc. all as per approved sample/ drawings and specifications complete and as directed by the Engineer-in-charge. |
| 65 | Providing and fixing 5 inch Antique Brass Finish Heavy Duty Door Security Brass Latch Lock of approved make or approved equivalent meeting all the technical parameters as per relevant codes and standards with necessary brass screws etc. all as per specifications and as per drawings complete as directed by Engineer-in-Charge. Note: Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 66 | Providing and fixing stainless steel aldrops of size 300 mm X 14 mm or as of approved size and shape with necessary screws, bolting from rear side complete as per specifications complete. Note: Sample(s) shall be submitted for approval of Engineer-in-Charge prior to procurement. |
| 67 | PART-2 : Electrical WorksLighting Fixture - Supply, installation, testing and commissioning of following LED lighting fixture as per tender specification. |
| 68 | Cylindrical lighting fixture as per TSS 01 |
| 69 | PVC Conduit - Supply and installation of PVC Conduit surface/concealed as per TSS 02 oftender specification |
| 70 | Point wiring - Supply, installation, testing and commissioning of point wiring as per TSS 03 of tender specification. |
| 71 | Wiring with 2.5 sq.mm copper wire (Primary switch box point for light/ fan) |
| 72 | Wiring with 2.5 sq.mm copper wire (Primary power point) |
| 73 | Wiring with 2.5 sq.mm copper wire (Secondary power point) |
| 74 | Wiring with 1.5 sq.mm copper wire (Primary light/fan point) |
| 75 | Wiring with 1.5 sq.mm copper wire (Secondary light/fan point) |
| 76 | Wiring with 1.5 sq.mm copper wire (Secondary switch box point for light/ fan) |
| 77 | Modular box - Supply and installation of following modular boxes as per TSS 04 of tender specification |
| 78 | 8 module box |
| 79 | 4 module box |
| 80 | Switches - Supply, installation, testing and commissioning of following modular switches as per TSS 05 of tender specification |
| 81 | 16A SP switch |
| 82 | 6A SP switch |
| 83 | Sockets - Supply, installation, testing and commissioning of following sockets as per TSS 06 of tender specification |
| 84 | 6/16A sockets |
| 85 | 6A sockets |
| 86 | 20A metal clad socket in box |
| 87 | Blanking Plates - Supply and installation of Blanking Plates as per TSS 07 of tender specification |
| 88 | Casing capping - Supply & installation of 25x12 mm size casing capping as per TSS 08 oftender specification |
| 89 | GI Flexible pipe - Supply andinstallation of GI Flexible pipe as per TSS 09 oftender specification |
| 90 | Exhaust Fan - Supply, installation, testing and commissioning of 300 mm exhaust fans aas per TSS 10 oftender specification |
| 91 | M S item - Supply & installation of MS items fabricated out of MS angles/channels as per TSS 11 of tender specification |
