|
| 1 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 2 | For fixed portion |
| 3 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 4 | Forshuttersofdoors,windows&ventilatorsincluding providingandfixinghinges/pivotsandmakingprovision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 5 | Powdercoatedaluminium(minimum thickness of powder coating 50 micron) |
| 6 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. |
| 7 | Pre-laminated particle board with decorative lamination on both sides |
| 8 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 9 | With float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm) |
| 10 | Providingandfixinganodisedaluminiumgrill(anodisedtransparent or dyed to required shade according to IS: 1868 with minimum anodic coatingofgradeAC15)ofapproveddesign/pattern,withapproved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 11 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod ofapproved quality as per architectural drawings and direction ofEngineer-in-charge complete. |
| 12 | Upto 5mm depth and 5 mm width |
| 13 | Providing and fixing 100mm Brass mortice latch and lock with 6 lever without pair of handles(best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 14 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 15 | 250x10 mm |
| 16 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm |
| 17 | Providing and fixing aluminium round shapehandle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge |
| 18 | Powder coated minimum thickness 50 micron aluminium |
| 19 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with Isi, IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701mm to 1000mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 20 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 21 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm |
| 22 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : 3000x16x5 mm |
| 23 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge. |
| 24 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete |
| 25 | Providing and fixing of Medium Density Fibre-board (MDF) of thickness 12mmin doorshutter in both side of MS framing with stainless steel screw complete and making edges round as per instruction of Engineer in charge. |
| 26 | Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : |
| 27 | Decorative veneer facings of approved manufacture |
| 28 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is furtherallowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction ofEngineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 29 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 30 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 31 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(49.5*49.5*4.5mm @ 5.95kg/m) |
| 32 | Electric resistance or induction butt welded tubes |
| 33 | Supply and installation of acoustic wall paneling - channeled Gyptech make,wall panel (2440x128x16mm) with all accessories including providing and fixing bonded fiber glass wool/polyster wadding (32x50mm) complete. Also include supply and fixing of wooden strip beading on top of the panels for complete finishing of the works on existing wood panel in the room. |
| 34 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 35 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 36 | Refixing of existing false ceiling by removing grid ,runner and tile. After removal of all grid, runner and tile contractor have to refix the ceiling suspended system to origial. |
| 37 | Providing and fixing bright finished brass handles with screws etc. complete: 125 mm |
| 38 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting offittingsandbrackets,cuttingandmakinggoodthewallswherever required:- |
| 39 | White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 40 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. |
| 41 | Wastecoupling38mmdiaof83mmlengthand77mm breadth, weighing not less than 60 gms |
| 42 | ProvidingandfixingP.V.C.wastepipeforsinkorwashbasinincluding P.V.C. waste fittings complete. |
| 43 | Flexible pipe |
| 44 | 40 mm dia |
| 45 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors |
| 46 | 100 mm inlet and 100 mm outlet |
| 47 | Sand cast iron S&S as per IS: 3989 |
| 48 | Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 |
| 49 | 15 mm nominal bore |
| 50 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain&brassthreadedfittingsandfixingthepipewithclampsat1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. |
| 51 | Concealed work, including cutting chases and making good the walls etc. |
| 52 | 15 mm nominal dia Pipes |
| 53 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. Thisincludesjointingofpipes&fittingswithonestepCPVCsolvent cementandtestingofjointscompleteasperdirectionofEngineerin Charge |
| 54 | Internal work - Exposed on wall |
| 55 | 50 mm nominal dia Pipes |
| 56 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 57 | 45 cm length |
| 58 | 15 mm nominal bore |
| 59 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 60 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 61 | 15 mm nominal bore |
