|
| 1 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area n. exc. 1.5sqm each, complete all as specified and as directed. |
| 2 | Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed. |
| 3 | M&L forSecondclass hard woodplain solid straight chowkhat andframes, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed. |
| 4 | M&L forFactory made2nd class hard woodplain, framed, panelleddoor shutter 35mm thick, twopanels with lock rail and panels of 12mm thick plywood BWR 9 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24(a) and fitted to Chowkats,complete all as specified and as directed. |
| 5 | S&F Factory made powder coated aluminium sliding type window (Triple Track type), fabricated to required size with standard aluminium sections with bottom track of size 92x31.75x1.6mm, side & top frame 92x31.75x1.4mm, top & bottom shutter rail with 39x17x1.4mm, outer style of size 39x17x1.4mm, interlock style of size 39x27x1.4mm of approved make according to IS (thickness of powder coating not less than 50 micron) including necessary glazing clips, with and including 4mm thick sheet frosted glass for two shutters fixed with rubber gasket and SS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm for wire mesh shutter fixed with aluminium beading, anodised aluminium fitting/fixture such as required number of rollers of suitable size, interlocking cleats/plates etc as required, complete all as specified and directed by the Engineer-in-Charge. Note : Quoted rate shall be inclusive of frame, shutter, sheet frosted glass, SS wire mesh and hardware such as butt hinges, tower bolts, handles, locking arrangement etc, complete as required at site. |
| 6 | M&L for solid PVC Door Frame of Size 50mm x 47mm out of 5mm prelaminated PVC sheet on both sides reinforced with M.S Square tube, supplying and fixing in opening as per sepcification and drawing, complete all as specified and as directed. |
| 7 | M&L for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out ofMS tube of top and bottom rails, MS frame shall be covered with heat moulded prelaminated PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheet for top rail ,lock rail and bottom rail on either side and as gap insert for top and bottom rail. Pannelling of prelaminated PVC sheet to be fitted in MS frame welded /sealed to the stiles and rails with suitable PVC sheet bedding and jointed together with solvent cement as per specification and drawings,complete all as specified and as directed. |
| 8 | S&F MS butt hingescold rolled medium weight 100mm size, ISI marked, complete all as specified andas directed. |
| 9 | S&F MS butt hingescold rolled medium weight 75mm size, ISI marked, complete all as specified andas directed. |
| 10 | S&F 150mm long extruded section aluminium alloy anodised handles fabricated type, complete all as specified and as directed. |
| 11 | S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specifiedand as directed. |
| 12 | S&F Aluminiumanodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified andall as directed. |
| 13 | S&F IN REPAIR Aluminiumanodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified andall as directed. |
| 14 | M&L for Floor door stopper of Brass body & tongue with 140mm long cover plate and hard drawn steel spring, fixed in door, complete all as specified and as directed. |
| 15 | M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applyingtwo coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed. |
| 16 | S&F MS Flat iron of size 25x3mm thick as in hold fast and similar small article conforming toFe-290 Grade-E-165, complete all as specified and as directed. |
| 17 | M&L for Preparation of new steel surfaces of any descriptionover 10cm width or girth and applyingtwo coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed. |
| 18 | S&F IN REPAIR Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed. |
| 19 | S&F IN REPAIR 4mm thick sheet glass ordinary quality andglazing with oil putty in squaresexc 0.5 Sqm in each pane, with and including hacking out old broken glass (any thickness/size, quality or description) from wooden frames, glazed with putty or fixed with beads, complete all as specified and as directed. |
| 20 | S&F Mild steel framed work such as safety grill door, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165, complete all as specified and as directed. |
| 21 | M&L for 75mm thick plain cement concrete 1:3:6type C1 (using 20mm graded hard granite stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3 mtres interval and joint filled with sealing compound, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 22 | M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.06Sqm but not exceeding 0.11Sqm, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed. |
| 23 | M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11Sqm but not exceeding 0.36Sqm, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed. |
| 24 | M&L for Light Shade Coloured Vitrified Ceramic tiles 08mm to 10mm thick (square/rectangular) area of each tile exc. 0.18 Sq.m. but n. exc. 0.36 Sq.m, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including demolition of existing floor tiles of any type with bedding mortar, complete all as specified and directed. |
| 25 | M&L for 75mm thick plain cement concrete 1:4:8 type D2 (using 40mm graded granite stone aggregate) as in sub base of flooring, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed. |
| 26 | M&L for Rubber coated chequered cement concrete tiles of size 300mm x 300mm x 25mm thick, with grey cement andpigments with GLOSSY FINISH set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bedin cement mortar 1:6 as in pathways, with and including demolition of existing floor tiles of any description, complete all as specified and as directed. |
| 27 | M&L for Premium quality, joint free ceramic glazed coloured wall tiles of 7 to 8mm thick (square / rectangular) area of each tile not exceeding 0.18Sqm, on vertical surfaces such as dado and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over & including 10mm thick rendering in CM 1:3 and including taking down existing dado/skirting with backing mortar, complete all as specified. |
| 28 | M&L for Factory made Machine pressed pre-cast concrete interlocking paver block any shape and size with glossy finish on top, confirming to IS 15658-2006 of 60mm thick, M-35 grade with grey cement and no pigment, with and including 50mm thick river sand cushion under interlocking paver block with watering and consolidation, with and including demolition of existing floor tiles of any type, complete all as specified and as directed by the Engineer-in-Charge. |
| 29 | S&F Mild Steel Plain Galvanised Steel Sheet 1.00mm thick of class 8, grade of zinc coating 275, as in ridges, hips, valley gutters, drip and straight flashing fixed with screws, with and including dismantling u/s steel sheet roofing and removing rubbish off the premises, complete all as specified and as directed. |
| 30 | S&F Pre painted galvalume aluminium zink coating GI based corrugatedsteel sheet 0.45mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and washers, with and including dismantlingplain or corrugated steel sheeting, any gauge, thickness in roof coverings, complete all as specified and as directed. |
| 31 | S&F Pre painted galvalume aluminium zink coating GI based plain steel sheet 0.45mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge, valley gutter, fixed with self tapping screws and washers, including dismantlingplain or corrugated steel sheeting, any gauge, thickness in roof coverings, complete all as specified and as directed. |
| 32 | M&Lfor Roof tiles, Mangalore pattern, interlocking at side joints, laid dry with and including dismantling u/s single layer MP tiles or similar tiles in roofing, removing rubbish off the premises, complete all as specified and as directed. |
| 33 | M&L for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6, with and including dismantling u/s MP tiles ridge cap, removing rubbish off the premises, complete all as specified and as directed. |
| 34 | M&Lfor Cement concrete roofing tiles, rustic red colour, 420mm x 330mm size of 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry, with and including dismantling u/s single layer MP tiles or similar tiles in roofing, removing rubbish off the premises, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
| 35 | M&L for Cement concrete Rusted Red/Grey colour Ridge cap of size 360mmx207mm x 240mm, with and including 15mm thick in roofing bedded and jointed in cement mortar 1:6, with and including dismantling u/s MP tiles ridge cap, removing rubbish off the premises, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
| 36 | S&F Mild Steel Corrugated Galvanised Steel Sheet 0.60mm thick of class 8, grade of zinc coating 275, as in roof covering with two corrugation side laps fixed with coach screws & washers, with and including dismantling u/s steel sheet roofing and removing rubbish off the premises, complete all as specified and as directed. |
| 37 | Dismantling existing u/s timber scantling framed work 40sq.cm and over section, in any position, complete all as specified and as directed. |
| 38 | S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle channel or flat sections includingdistance pieces, cleats etc. conforming to gradeFe 410-W Gde E - 250 quality \"B\", with and including dismantling existing wooden fillets / wooden members of any description, complete all as specified and as directed. |
| 39 | S&FMild Steel work as in wind tiesetc. conforming toFe-290 Gde- E-165, with and including dismantling of mild steel work of any description and in any position, complete all as specified and as directed . |
| 40 | M&L for PCC type B0 [1:2:4] using 12.50mm graded stone aggregate) as in copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, finished plain fair faces, including demolition of old cement concrete of any type, complete all as specified and as directed. |
| 41 | M&L for Preparing surface of old wood and wood based materials, new or old, of any description and girth and treated with creosote oil, complete all as specified and as directed. |
| 42 | S&FPVC (SWR) eaves gutter 150mm dia trapezodial shape Gde-Ifixed with MS clamps, including taking down existing u/s eaves gutter pipes, rain water pipes(of any size or pattern) including fittings, head shoes, bends, swan neck etc., complete all as specified and as directed. |
| 43 | S&F IN REPAIR Black Colour PVC flexible pipe (waste pipe) of suitable length, suitable for 32mm waste coupling of sink / wash hand basin / urinal, complete all as specified and as directed |
| 44 | M&L for False ceiling with High Pressure Steam Cured (HPSC) 4mm thick Non Asbestos Fibre Cement ceiling boards fixed with and including supply & fixing powder coated aluminium snap grid of size 605mmx605mm consisting of 25X25X1.25mm aluminium angles and TEEs of size 35x25x1.25mm with galvanised wire of required length and 6mm dia hanger grid suspended from trusses/ ceiling and purlins not exceeding 1200mm c/c both ways, with and including applying three coats of white wash on ceiling surface, with and including taking down existing u/s ceiling with frame work of any description, complete all as specified and as directed. |
| 45 | S&F Unplasticised PVC (uPVC) pipe of 20mm bore of pipe of pressure rating 10 kgf/cm2 with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) and fixed to walls/ceilings/ laid in floors, including testing, with and including taking down existing u/s GI pipe, complete all as specified and as directed. |
| 46 | S&F Unplasticised PVC (uPVC) pipe of 15mm bore of pipe of pressure rating 10 kgf/cm2 with and including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) and fixed to walls/ceilings/ laid in floors, including testing, with and including taking down existing u/s GI pipe, complete all as specified and as directed. |
| 47 | S&Fin repair 15mm dia Bib tap, cast copper alloy Fancy type CP brass long body, screwed down, screwed for iron pipe or for brass ferrule and fixedcomplete all as specified and as directed. |
| 48 | S&F in repair 15mm dia Stop valvefancy type chromium plated with long shank and cup (concealed type) screwed down, screwed for iron pipe or for brass ferrule and fixedcomplete all as specified and as directed. |
| 49 | S&F in repair 15mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm 90gms)complete all as specified and as directed. |
| 50 | S&F in repair Vitreous china squatting pan, Orissa pattern size 580 x 440 mm white with integral foot rest including \"P\" or \"S\" trap etc., with and including cement concrete bedding, complete all as specified and as directed. |
| 51 | S&F IN REPAIR Vitreous china Wash down water closet pan EWC (Pedestal pattern), white with\"P\"or \"S\" trap étc,(excluding flushing cistern and flush pipe) including plastic water closet seat cover closed pattern with flat bottom cover, mild steel chromium plated or aluminised hinging device, fixing bolts,etc, complete all as specified and as directed. |
| 52 | S&F IN REPAIR PVC valveless, syphonic action type low level flushing cistern, 10 ltrs capacity, white with inlet ball valve, float and handle soft touch type including brackets, PVC flush pipe etc complete fixed with CP brass screws complete all as specified and as directed. |
| 53 | S&F IN REPAIR 15mm bore dia brass CP Mixer for mixing hot and cold water screwed down for iron pipe and fixed, complete all as specified and as directed. |
| 54 | S&F IN REPAIR Brass chromium plated overhead shower with shower arm flange, withswivel joints, any size, fixed to 15mm bore steel pipe, fixed in repair, completeall as specified and as directed. |
| 55 | S&F IN REPAIR Corner glass shelf, 5mm thick, 9\" wide, fixed with suitablemild steel CP brackets, nuts & bolts, fixed in repairs complete all as specified and as directed. |
| 56 | S&F IN REPAIR Vitreous china wash basin, white, size 550x400mm, including CI brackets, with PVC waste pipe and waste fittings and cutting for and pinning in ends of brackets or erecting stands etc., complete all as specified and as directed. |
| 57 | S&F IN REPAIR Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot\" or ‘Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixedcomplete all as specified and as directed. |
| 58 | S&F IN REPAIR Brass chromium plated toilet paper holder fixed to wall with chromium plated brass screws complete all as specified and as directed. |
| 59 | S&F IN REPAIR Soap dish, vitreous china, white of size 160mm x 160mm x 90mm fixed with plugs with chromium plated brass screws, completeall as specified and as directed. |
| 60 | S&F IN REPAIR Health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook, complete all as specified and as directed. |
| 61 | S&F IN REPAIR Tubular towel rod 600 mm, brass chromium plated, fixed to walls with plugs and chromium plated brass screws, complete all as specified and as directed. |
| 62 | S&F IN REPAIR 15mm bore 2 way Bib tap, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc., compete all as specified and as directed. |
| 63 | S&F IN REPAIR Mirror cabinet of selected quality of size 350mm x 450mm x 5mm thick fixed on wall with suitable MS screws, completeall as specified and as directed. |
| 64 | S&F IN REPAIR seat cover for EWC closed pattern with flat bottom and mild steel chromium plated hinging device, complete all as specified and as directed. |
| 65 | S&F IN REPAIR 600mm x 450mm x 5.50 mm thick bevelled edged mirror of selected quality glass mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers with aluminium frame all around, complete all as specified and as directed. |
| 66 | S&F PVC connections 15 mm size with PTMT nuts 600mm long,complete all as specified and as directed. |
| 67 | S&F IN REPAIR 3 way mixer tap for mixing hot and cold water fancy type brass chromium plated screwed down for 15mm bore GI pipe, complete all as specified and as directed. |
| 68 | S&F IN REPAIR Vitreous China wash down water closet pan (pedestal pattern) white , cascade model with and including Symphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe including brackets and connection pipe, complete all as specified and as directed. |
| 69 | M&L Preparing old plastered surfaces of walls by brooming down and washing with water and applying one coat of oil bound distemper white or tinted, complete all as specified and as directed. |
| 70 | M&L Preparing old plastered surfaces of walls by brooming down and washing with water and applying two coats of plastic emulsion paint, complete all as specified and as directed. |
| 71 | M&L for Preparing old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed. |
| 72 | M&L for Preparing oldsteel surfaces of any descriptionover10 cm width or girth and applying one coat of synthetic enamel paintcomplete all as specified and as directed. |
| 73 | M&L for Complete removal of existing treatment on old walls with wire brush, scrapping down smoke soot, mould, moss nad efforescent salts, oils & greasy spots etc., and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with siliconadditives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including preparation of old surfaces of any description, complete all as specified and as directed. |
