|
| 1 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. |
| 2 | In cement mortar |
| 3 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 4 | Asbestos cement sheet |
| 5 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : |
| 6 | 150 mm dia pipe |
| 7 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 8 | Carriage of materials by Mechanical Transport including loading, unloading and stacking : |
| 9 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more. |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 12 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 14 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 16 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 17 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 18 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 19 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with : |
| 20 | 4.0 mm thick glass panes. |
| 21 | 12 mm cement plaster of mix : |
| 22 | 1:4 (1 cement: 4 fine sand) |
| 23 | 1:6 (1 cement: 6 fine sand) |
| 24 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 25 | 1:6 (1 cement: 6 fine sand) |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 27 | Two or more coats on new work. |
| 28 | Renewing Wrought iron or M.S. Wheel or roller of steel door or gate and fitting and fixing the same with necessary clamps, nuts and bolts / welding and erection etc. complete. |
| 29 | Wheel 50 mm dia. and below. |
| 30 | Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) |
| 31 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge. |
| 32 | (a) Internal Work- Exposed on wall |
| 33 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 34 | 10 litre capacity - White |
| 35 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall. |
| 36 | 50 mm dia. nominal bore |
| 37 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) |
| 38 | 50mm nominal bore |
| 39 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 40 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 41 | Providing and fixing PTMT stop cock of approved quality and colour. |
| 42 | 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 43 | Providing and fixing PTMT pillar cock of approved quality and colour . |
| 44 | 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 45 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 46 | 15 mm nominal bore with 45 cm length. |
| 47 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 48 | 25 mm average thickness |
| 49 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. |
| 50 | Bars upto 12 mm diameter |
| 51 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. |
| 52 | SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 53 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). |
| 54 | 25 mm average thickness in 2 layers. |
| 55 | Taking out aluminium door shutters for repair (area of 3.00 sqm and below) and refixing the same with new steel hinges, if required, complete as per direction of Engineer-in-charge. |
| 56 | Providing and fixing two point M.s oxidised Handle of Steel windows as directed all complete. |
| 57 | Providing and fixing oxidised M.S. casement stays (straight peg type) 250 mm weighing not less than 150 gms. with necessary screws etc. complete. |
| 58 | Renewing hinge of steel shutter including taking out old one by cutting, fixing new hinge by welding and making good complete. |
| 59 | Renewing M.S Members of steel shutter by Welding including taking out old ,mending good damages complete, including taking out and refixing glass panes. |
| 60 | Cleaning and desilting of Inspection chamber of sewer line and removal of night soil mixed with earth and disposal of the same to dumping ground out side campus as per instruction of Engineer in charge. |
| 61 | Cleaning and desilting of sewer line and removal of night soil mixed with earth and disposal of the same to dumping ground out side campus as per instruction of Engineer in charge. |
| 62 | Labour charges for de-clogging choaked W.C. pan and cleaning it with acid etc complete as per direction of Engineer-in-charge. |
| 63 | Providing and fixing uPVC floor trap 100mm dia inlet and 100 mm dia outlet. |
| 64 | Providing and fixing uPVC pipes (SCH 40 uPVC as per ASTM D- 1785 pipes) including all uPVC plain and brass threaded fittings. Including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall |
| 65 | 15 mm nominal bore |
| 66 | 20 mm nominal bore |
| 67 | 25 mm nominal bore |
| 68 | 50 mm Nominal bore. |
| 69 | Providing and fixing high pressure PVC ball valve (Solvent Weld) of make Supreme or equivalent with pressure class SCH:80 of approved quality including the cost of necessary uPVC socket, pieces of pipes etc. required for the work complete as per direction of Engineer-in-Charge : |
| 70 | 20 mm nominal dia |
| 71 | 25 mm nominal dia |
| 72 | Supply & fixing of uPVC pipe fittings conforming to ASTM D - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part-I). |
| 73 | MTA (Brass)-25 mm nominal bore |
| 74 | Uprooting and removing small plants from the surface of walls, parapet, etc. at any height by cutting chase for removing roots and using necessary chemicals etc. to prevent further growth of plants and mending good damages complete. |
| 75 | Small plant of girth of exposed stem up to 75mm |
| 76 | Felling of trees like banyan, pipul etc from compound walls, building walls, cornices etc by making scaffolding where necessary including cutting of trunks and branches, application of chemicals/weedicides to the remaining portion to kill the growth of tree and ultimately removing the roots from the walls by cutting walls and mending good complete. ( The rate is inclusive of the mending good the walls with bricks/concretes/plasters and disposing of branches/trunks to vats inside compound for further disposal) |
| 77 | Of girth above 30 cm upto 60 cm (measured above 1.0 m from GL ) |
| 78 | Erection of single layer bamboo-scaffolding made of average 75 mm dia bamboos with adequate bracing, ties, ropes etc. for strong, stable and workable scaffolding for specified jobs ( above GF beyound 4.00m height) like replacement of sewage/ RW pipes & accessories, replacement of hinges steel windows , special repairs, etc including dismantling the scaffolding after the job is done and clearing the site complete as per the direction of the Engineer-in-charge. [ to be Paid only once for all special works] |
| 79 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. |
| 80 | 160 mm diameter |
| 81 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 82 | 160 mm diameter |
| 83 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. |
| 84 | Bend with Door -160 mm dia |
| 85 | Applying anti-rust passive coating (like Sika Rustop or equivalent) over reinforcement bars after thorough cleaning of reinforcement complete as per direction of Engineer-in-charge. |
| 86 | Up to 25 mm dia bars |
| 87 | Attending repairs to MS gate by removing corroded portion of gate with welding machine at site and replacing with new members as per actual requirement at site. (Cost for labour and hire charges of welding machine including transporation, consumables. Steel members will be paid separately) |
| 88 | Providing and welding 2mm thick M.S. sheet to existing M.S. frame work including providing and appying a priming coat of approved steel primer all complete. |
| 89 | Labour charges for lifting built up heavy grills (Single sections) joining with nut bolts and keeping in postion till fixing on top of compound wall complete as per direction of Engineer-in-charge.( Rate should be inclusive of cost of nut-bolts, scaffoldings but with out cost of primer) |
| 90 | Labour charges for carefully cutting marble floor & floor concrete (approx 600 x 600 mm) for taking out damaged floor trap including cleaning the rubbish complete as per the direction of Engineer-in-charge. |
| 91 | Credit for taking away dismantled unserviceable materials : |
| 92 | Dismantled bricks |
| 93 | Dismantled C.I. pipe |
| 94 | Dismantled G.I. pipe-upto 50mm |
| 95 | Dismantled steel materials |
