|
| 1 | Excavating in trenches in loose/soft soil, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed. |
| 3 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 4 | M&L forplain cement concrete (1:4:8) type D2, using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. |
| 5 | M & L precast cement concrete 1:3:6, type C1 (20 mm graded stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in CM 1:6 etc. complete all as specified and directed. |
| 6 | M&L for rendering 15 mm thick in two coats (5 mm thick in cement mortar 1:4 with water proofing compound as per manufacturers instructions over 10 mm thick plaster in CM 1:6) on fair faces of brick work or concrete blocks surfaces finished even and smooth without using extra cement. |
| 7 | Dismantling structural steel work including doors, gates (collapsible gate) but excluding framed truss etc, including necessary cutting up of frame all as specified and directed. |
| 8 | Demolition of brick work or stone masonry of any description and in any position built in cement mortar including all quoins, arches pillar etc including disposal of rubbish complete all as specified and directed. |
| 9 | Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m, all as specified and directed. |
| 10 | Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thick below or above G.L including floor tiles/finishesof any type, complete all as specified and directed . |
| 11 | M&L for Preparation of newly plastered surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specifiedand directed. |
| 12 | M&L for 15mm thick rendering other than fair face of brick/stone masonry wallsin CM 1:6finished even and smooth without using extra cement all as specified and directed. |
| 13 | M&L for 2mm thick wall care putty over plastered surface all as specified and directed. |
| 14 | M&L for Preparation of newly plastered surface of wall andapplying two coat of distemper oil emulsion over a coat of primer white or tintedas approved all as specifiedand directed. |
| 15 | M&L for RCC nominal Mix 1:2:4type B1 (using 20mm graded crushed stone aggregate) as in Beams (plinth Beam and lintel Beam) cantilevers, bressummers, lintels over 1.5m span etc, all as specifiedand directed. |
| 16 | M&L formwork to sides and soffits of beam, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc of flat concrete surfaces fair finished, all as specifiedand directed. |
| 17 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 18 | Same as per item No 17 above but 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders, all as specifiedand directed. |
| 19 | M&L for Re-barring TMTreinforcement bars to existing building up to 150mm including the charges for cutting , bending, welding etc placing and fixing in position using Lok-Fix (Manufactured by M/s Fosroc Chemicals India Ltdor equivalent)complete Including the cost of steel bars complete all as directed. |
| 20 | S&F GI Tubular steel sections for shed, trusses, rafters, purlins, vertical post and fastenings and framing jointed with angle cleat, MS Flat, MS plates cutting, welding necessary drilling holes and distance pieces, cleats etc. complete all as specified and directed. Make: ISI Marked as approved by GE. |
| 21 | M&L preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 22 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 23 | S&F 4mm thick HPSC pre-prime non asbestos fibre cement building board (E-classic) decorative finish including pre powder coated GI frame with suspension system (Grid) of size 600x600mm comprising of T section 25mmx32.5mmx 1.6mm size as main runners and wall angle to be placed along the wall at desired level of the False ceiling suspended with 4mm dia GI suspender of suitable size @ 1200 mm centre to centre distance all as specified and directed. Make: Armstrong, Everest, Ramco etc |
| 24 | Spreading and levelling of earth obtained from excavation and filling under floor in layers n exc. 25cm thickand well ramming including watering as required, all as specified and directed. |
| 25 | M&L for 75 mm thick plain cement concrete (1:3:6) type C2, using 40 mm graded stone aggregate as in Plinth protection and finishing the surface even & smooth without using extra cement complete all as specified and directed. |
| 26 | M&L for hard-core of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, all as specified and directed. |
| 27 | M&L 100mm thick cement concrete 1:4:8 Type D2 ( using 40mm graded stone aggregates) as in sub base complete all as specified and directed. |
| 28 | M&L for 25 mm thick PCC (1:2:4) type B0(12.5 mm graded stone agg) as in sub base of flooring complete all as specified and directed. |
| 29 | M&L forNon -skid ceramic tiles 7 to 8 mm thick (Matt finish) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredcement over and including 15 mm thick screed bed or bedding in layer of mortar for laying floor finishes in cement plaster 1:6 complete all as specified and directed. |
| 30 | M&L for glazed ceramic coloured tiles in vertical surface600x 300x 8 to 10mm thickset andjointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering on brick work or concrete surface in cement mortar 1:4 as backing coat, complete all as specified and directed. |
| 31 | Supplying and laying 20mm (Outer dia) of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 32 | ‘- Ditto- all as per item No 31 above but 25 mm (Outer dia). |
| 33 | M&L for cutting chases for concealed water tubing or inserting roof sheet inside wall, etc. making good to facings where required and pointing in cement mortar 1:3 /PCC 1:2:4 type B0 not exc 10 cm girth complete all as specified and directed. |
| 34 | M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) infloors, steps pillar, platform or ovalshape wash hand basin including cutting to fit theWHB, partitionand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 35 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position withlugs/SS dash fasteners of required dia and length complete, all as specified and directed. |
| 36 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete, all as specified and directed. |
| 37 | S&F 100mm butt hinges Stainless steel and fixed with SS screws complete all as specified and directed. |
| 38 | S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed . |
| 39 | S&F 150mm long aluminium barrel tower bolts, of extruded section complete all as specified and directed . |
| 40 | S&F 250 mm long aluminium alloy, anodised ,sliding door bolt with hasp , staple (bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminium alloy and fixed complete all as specified & directed. |
| 41 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for Frame & shutters for ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate sections and other sections of approved make, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete, all as specified and directed |
| 42 | M&L for powder coated aluminium coated deco grill of approved colour, design & pattern, with approved standard section fixed to window frame with \"F\" channels & stainless steel screws @ 200 mm centre to centre, all as specified and directed |
| 43 | S&F Aluminium alloy wire cloth, 0.45 mm, nominal dia of wire and average width of aperture 1.40 mm and fixed with wooden beadings etc. complete all as specified and directed. |
| 44 | S&F 3mm thick Figured glass, pin head type and glazing to aluminium frame/ shutters. |
| 45 | S & F vitreous china wash basin, any colour, counter top oval shape size 550 X 450mm including 32mm Brass CP waste Coupling and PVC Waste pipe, CP grating complete all as specified and directed. Make:- CERA (CLIFF/CONCORD/CLAIR) /Hindware /Parryware etc, all as specified and directed |
| 46 | S&F 15mm bore Pillar cock with swan neck spout (left/right) and aerator fancy type, CP screwed down high pressure complete all as specified and directed.Make : CERA Cat No- F2008105, Jaquar CON-127BKN or equivalent in Hindware, all as specified and directed |
| 47 | S&F PTMT Jet spray to be fixed to closet pan pedestal pattern Water closet. Make: Prayag, CERA, Hindware |
| 48 | S&F CP Towel Rail 600 mm fixed with SS screws and PVC Rawal plug complete all as specified and directed. Make: CERA Cat. No. F5013103CH, Jaquar Cat No AQN-7781 etc |
| 49 | S&F Chromium plated Urinal spreader complete. Make:-CERA - Cat No F8070201or equivalent in Jaquar & Hindware |
| 50 | S&F Vitreous China Urinal, half stall type, white including CP Brass waste coupling, PVC waste pipe & CP Grating complete, all as specified and directed. Make:- CERA/ Hindware /Parryware |
| 51 | S&F Vitreous China wash down water closet pan pedestal pattern, with P or S Trap white including Plastic water closet seat, closed pattern with flat bottom, and cover and suitable hinges, all as specified and directed Make:- CERA/Hindware /Parryware |
| 52 | S&F 10 litre capacity PVC valve less symphonic action type flushing cistern low level, white, with inlet, ball valve, float and handle including brackets and Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed. Make:- CERA/Hindware /Parryware |
| 53 | S&F Health faucet (ABS Body) chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and ABS wall hook including making connections and fixed in position complete, all respect as specifiedMake: CERA/Parryware/ Prayag |
| 54 | S&F 6mm thick Frameless Mirror of size 900mm x 600mm bevelled edge,of selected quality glass, fixed with hidden screws or SS decorativebrackets /Cup washerswith screws and Rawal plug complete, all as specified and directed |
| 55 | S&F 15mm bore chromium plated long body bib taps with crutch or butterfly handle fancy type screwed down screwed for iron pipes or for brass ferrule complete all as specified and directed. |
| 56 | S&F 15mm bore Angle Cock / stop Cock, Brass CP, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, all as specified and directed Make: CERA/Parryware/ Prayag |
| 57 | S&Fin repair for PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 58 | S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, floor or in wall complete all as specified and directed. |
| 59 | S&F 75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, floor or in wall complete all as specified and directed. |
| 60 | S&F 110mm PVC(SWR) bends complete all as specified and directed. |
| 61 | S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal, all as specified and directed |
| 62 | S&F 75mm dia outlet PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, all as specified and directed |
| 63 | S&F 75mm dia outletPVC (SWR) multi floor trap with CP grating including jointing with solvent cement, all as specified and directed |
| 64 | S&F 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal, all as specified and directed |
| 65 | S&F 75 mm dia PVC (SWR) junction single, (Single T) equal or unequal, all as specified and directed |
| 66 | S&F 75 mmPVC (SWR) vent cowl, all as specified and directed |
| 67 | S&F 110 mmPVC (SWR) vent cowl, all as specified and directed |
| 68 | S&F20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, all as specified and directed |
| 69 | S&F 500 lit capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position with 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight2 1 0 g m s)complete all as specified and directed. |
| 70 | S&F Curved shape 8mm thick frosted glass urinal partition size (900x 450) including necessary SS fixing Brackets fixed with all accessories like SS Screws,PVC Rawal plugs, fasteners etc complete, all as specified and directedMake: Jaquar Cat No: SE-CHR-810UC450X /JSE-CHR-810US450X or equivalent in CERA & Parryware |
| 71 | S&F Toilet paper holder Paper with flap guard/Flap Recessed Type (Stainless Steel), all as specified and directed Make:CERA Cat. No. F5013110CH, Jaquar Cat No -AHS-1553 etc |
| 72 | S&F Liquid soap holder /Hand wash dispenser fixed to wall with SS screws and PVC Rawal plugs etc complete, all as specified and directed. Make: CERA Cat. No.F5013111CH or equivalent inJaquar& Parryware. |
| 73 | M& L for point wiringconcealed type complete with 1100 volts grade 1.5 sqmm (FRLS) PVC insulated, unsheathedsingle core multistranded copper conductor cable including 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable as earth continuity conductor drawn through in and including PVC conduit of suitable size with all accessories including modular inner & outer cover plate and modular GI box made of 1.6 mm thick for fixing modular switches/bell push/socket/regulators etc including all necessary wall cutting chases and making good disturbed surfaces in cement mortar 1:3 for One light point controlled by one switch, complete all as specified and as directed. |
| 74 | ‘-Ditto- All as per item No 73 above but one exhaust fan point controlled by one switch. |
| 75 | ‘-Ditto- All as per item No 73 above but one 3 pin 5 Amps socket outlet point on independent board |
| 76 | Supply and fix switch one way 10 Amps, single pole,230 volts modular type complete all as specified and as per directed. |
| 77 | Supply and fix socket outlet 6 amps 2/3 pin combined modular type complete all as specified and as directed. |
| 78 | Supply and fix ceiling rose surface Bakelite 65x50 mm two to three terminals, all as specified and as directed. |
| 79 | Supply and fix sheet metal enclosure (for DB\"s when MCBs to be used), single pole and neutral double door, 4 way, 240 Volts with 200 Amps rated bus bar complete all as specified and as directed. |
| 80 | Supply and fix MCB single pole, 240 volts 6 to 32 Amps \"B\" curve complete all as specified and as directed. |
| 81 | Supply and fix MCB single pole and neutral 32 Amps,10kA, 240 Volts, \"C\" curve complete all as specified and as directed. |
| 82 | M&L sub main wiring surface type with 2 runs of single core 4 sqmm size PVC insulated unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC conduit and its accessories including provision of one run of 4 sqmm PVC insulated single core unsheathed copper multistranded conductor cable as earth continuity wire complete all as specified and directed. Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre. |
| 83 | Supply and fix LED batten 1x 20 watt 4 feet long suitable for indoor applications withintegrated electronic driverof operating voltage 110 to 265 Volts complete with necessary electric connection through suitable size flexible wire complete all as specified and as directed. |
| 84 | Supply & fix exhaust fans made of sturdy engineering plastic complete with louvers shutter, AC single phase 230 V,50Hz,RPM 1200 copper winding of size 250 mm sweep complete all as specified and as directed |
| 85 | Making hole of suitable size for fixing exhaust fan of size 300 mm on the wall and grouting including plastering complete all as specified and directed. |
| 86 | M & Learthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth plate not less than2.25 Metre deep below ground level)with top edge of the plate not less than1.5 metrebelownormal ground levelconnected to galvanised earth wire4.0 mmdia bymeans ofbolts, nuts check and washers ofG I or steel all as shown in electrical plate No. 5 of SSR Pt -Iconnected to earthingtest point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation,earth work in any typeof soil, PCC chamberand MS coverconnecting lead wire from test point to Main DB complete all as specified & directed |
