|
| 1 | Material and labour for repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in roads, paths, etc cutting around edges to at least 25 mm in depth, making good by applying tack coat @5 Kg per 10 Sqm using paving bitumen of VG-10 and putting in premixed bituminous macadam using VG-30, well rammed and sealed with binder 9.8 kg per 10 Sqm, blinded with 0.09 Cum of stone chippings, 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings) depth of hole exceeding 30mmcomplete all as specified and as directed. |
| 2 | Material and labour for Premix Bituminous Macadam with binder content of 4% by weight of total mix using paving bitumen of VG-30, laid rolled and compacted to required camber and gradient (Consolidated thickness 75 mm or less) with mechanical paver rolled and compacted to required camber and gradient with 8 to 12 tonne power roller complete all as specified and as directed. |
| 3 | Material and labour for preparing existing blacktop/ newly laid bituminous macadam surfaces by brushing with wire brushes or using pressure blower and compressor for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bagsto remove all loose dirt applying tack coat @ 5 Kg per 10 Sqm usingBituminous Cold Emulsion Rapid setting Grade-1 (RS-1) etc complete all as specified and as directed. |
| 4 | Material and labour for Bituminous Premix Semi Dense Asphaltic concrete 40mm consolidated thickness using paving bitumen of Grade VG-30 with 5.5% binder content by weight of total mix using hot mix plant and mechanical paver rolled and compacted to required camber and gradient with 8 to 12 tonne power roller complete all as specified and as directed. |
| 5 | Material and labour for Applying 2 mm thick road marking paint with reflective thermoplastic white road marking paint confirming to BS-3262 (1989), either continuous or broken lines over existing or new painting surfaces of cement or bituminous surface, laid down through road marking machine using thermo plastic material by incorporating the white glass powder for reflectivity in 100 mm width in white or golden yellow colour by using applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, including cleaning the road surface of all dirt, seals, oil grease and foreign material etc complete as direction of Engr-in-Charge and in accordance with applicable specification complete all as specified and as directed. |
| 6 | Supply and fix in repaircat eye poly carbonate body of size 100mm x90mm x15mm with retro reflective prismatic tape fixed with road as per manufactures instructions complete all as specified and as directed. |
| 7 | Supply and fix in repairs solar cat eye aluminium alloy shall (100% water proofing design according to IP 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 MCD completed as per manufactures instructions etc complete all as specified and as directed. |
| 8 | Supply and fixing in repair metal tubular dealineator made out of ABS round body fitted with 02 Nos 65mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed. |
| 9 | Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) etc. complete all as specified and as directed. |
| 10 | Material and labour for plain cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in coping sides of road complete all as specified and as directed. |
| 11 | Material and labour for forming 12mm thick expansion joint for 100mm thick slab filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound grade \"A\" complete all as specified and as directed |
