Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortarbedding (but including backing ), rubbish off the premises, complete all as specified and directed by engr-in-Charge. |
| 2 | Material & Labour 25mm thick PCC 1:2:4 using12.5mm graded crushed stone aggregates as in flooring and finished surface as in received tiles, complete all as specified and directed by engr-in-Charge. |
| 3 | M&L for Glazed ceramic colouredtiles in vertical surface 450x350x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match (Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) incl10mm thck plaster below tile for dado/skirting CM 1:4, complete all as specified and directed by engr-in-Charge. |
| 4 | M & L for Non-Skid Ceramic tiles 7 to 8 mm thick (Square/rectangular ) area of each tile exc 0.06 Sq.m but not exc 0.11 sq m in floors etc set and jointed in neat cement slury and pointed in white or coloured cement match including screed bed or bedding layer of 15mm thick in cement mortar (1:6), complete all as specified and directed by engr-in-Charge. |
| 5 | M&L for Vitrified tiles 8-10 mm thick in size of 600mmx600mm as in floors/skirting/dados set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15mm thick in cement mortar (1:6),complete all as specified and directed by engr-in-Charge. |
| 6 | Taking down chowkhat or frames exc 1.50 Sqm n.exc 4 Sqm (without taking down shutters from the frames), complete all as specified and directed by engr-in-Charge. |
| 7 | Taking down chowkhat or frames n.exc 1.5 Sqm (without taking down shutters from the frames), complete all as specified and directed by engr-in-Charge. |
| 8 | S&F in repairs anodised aluminium door powder coated, frame of door made out of aluminium extruded section 100mmx45mmx2.6mm thick, shuttermade out of aluminium extruded section 85mmx45mmx2.1mm thick except bottom rail and lock rail, the section of bottom rail and lock rail 100mmx45mmx2.1mm complete with hydraulic floor mounted door closer, ISI marked, aluminium anodised tower bolt 2 Nos, 5.5mm thick tinted/plane glass pane including reoprene dry rubber gasket set, stainless steel screws, hinges, aluminium anodised snap beading including all necessary fittings and fixtures made out of aluminium anodised complete, complete all as specified and directed by engr-in-Charge. |
| 9 | S&F in repairs anodised aluminium sliding glazed window powder coated of two/three trackframe of window made out of aluminium extruded section 90mmx30mmx2.6mm/ 60mmx30mmx2.6mmthick, shutter made out of aluminium extruded section 38mmx20mmx1.5mm thick including holdfast, anodised aluminium handlw of suitable size, necessary joining cleats, glazing clips,5.5mm thick tinted/plane glass pane including reoprene dry rubber gasket set, stainless steel screws, hinges, aluminium anodised snap beading including all necessary fittings and fixtures made out of aluminium anodisedsuch as handles, locking arrangements, complete all as specified and directed by engr-in-Charge. |
| 10 | M&L for plain sheet glass 4.00mm thick ordinalry quality and glazing with oil putty or wooden beads in square or fixed with aluminium section including rubber beads not exc 0.50 sqm in each pane, complete all as specified and directed by engr-in-Charge. |
| 11 | S&F in repair Door closer hydraulically regulated designation No 3 universal type, aluminium body suitable for door shutters of up to 700 mm in widthand weight not more than 35 Kg and fixed, complete all as specified and directed by engr-in-Charge. |
| 12 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges andnecessary S S screws shall be paid separately) and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made, complete all as specified and directed by engr-in-Charge. |
| 13 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges andnecessary S S screws shall be paid separately), complete all as specified and directed by engr-in-Charge. |
| 14 | S&F 2nd hard wood as in plain solid straight chowkhats wrought framed rebated on the solid put together onwith glue pinned at joints, complete all as specified and directed by engr-in-Charge. |
| 15 | S & F 30mm thick 2nd class hardwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkhats, complete all as specified and directed by engr-in-Charge. |
| 16 | S & F 30 mm thick 2nd class hardwood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and directed by engr-in-Charge. |
| 17 | S&F 200mm long aluminium anodised barrel tower bolt of extruded section in old or new position, complete all as specified and directed by engr-in-Charge. |
| 18 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed by engr-in-Charge. |
| 19 | S&F aluminum door handle cast type 150 mm in old or new position, complete all as specified and directed by engr-in-Charge. |
| 20 | S&F 100mm long mild steel medium weight but hinges cold rolled, complete all as specified and directed by engr-in-Charge. |
| 21 | Taking down cement plaster on brick/pcc block or conc surfaces including racking out joints hacking for key, scrubbing down with water etc., complete all as specified and directed by engr-in-Charge. |
| 22 | M&L rendering 15mm thick in CM 1:4 on fair faces of concrete or brick surfaces as in wall finishes even and smooth w/o using extra cement, complete all as specified and directed by engr-in-Charge. |
| 23 | M&L rendering 15mm thick in CM 1:6 on other than fair faces of concrete or brick surfaces as in wall finishes even and smooth w/o using extra cement, complete all as specified and directed by engr-in-Charge. |
| 24 | M&L for Preparing newly plastered surfaces of wallsand applying two coats of acrylic emulsion paint over a coat of primerand over a coat of wall care putty applied till the surface is smooth etc, complete all as specified and directed by engr-in-Charge. |
| 25 | M&L for Preparing old treated/untreated plastered surfaces of wallsand applying two coats of distemper oil emulsion,over a coat of primerand over a coat of wall care putty applied till the surface is smooth including complete removal of existing treatment of any description etc, complete all as specified and directed by engr-in-Charge. |
| 26 | Prepration of new plaster surface of wall and applying two caot of cement base paint over a caot of primer includingbalance areacomplete removale, complete all as specified and directed by engr-in-Charge. |
| 27 | Demolition of cement concrete (un reinforced ) in ground floors and pavings n.exc 15cm thick (below or above ground level )and removing debris ouside MD land, complete all as specified and directed by engr-in-Charge. |
| 28 | Material & Labour 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m, complete all as specified and directed by engr-in-Charge. |
| 29 | Dismantling plain or corrugated steelsheeting any gauge thickness including nanital or similar pattern, complete all as specified and directed by engr-in-Charge. |
| 30 | S&F 0.63 mm thick galvanised mild steel sheets with two corrugation side lap fixed with J or L hooks with grade of zink coating 275, complete all as specified and directed by engr-in-Charge. |
| 31 | S&F rolled section as in main and cross beams ,hip and jack rafters , purelins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates Fe -410 Gde E-250, complete all as specified and directed by engr-in-Charge. |
| 32 | Dismantling structural steel work including doors and gates of any description, complete all as specified and directed by engr-in-Charge. |
| 33 | M&L for two coat of synthetic enamel paint on new /previous untreated corrugated steel surface including prepation over a coat of red oxide zinc chrome primer with modrant solution, complete all as specified and directed by engr-in-Charge. |
| 34 | S& F 1000 ltr capacity rotationalmoulded polythelene water storage tanks triple layer white colour (cylindrical vertical with clossed top) hoisted and fixed in position including dismantling all as specified in SSR Part 1, complete all as specified and directed by engr-in-Charge. |
| 35 | Dismantling of water tank of any description capacity exc 500 ltr and not exc 1000 ltr, complete all as specified and directed by engr-in-Charge. |
| 36 | Taking up or down steel tubing 20mm bore including cleaning for refixing or removal to store, complete all as specified and directed by engr-in-Charge. |
| 37 | Taking up or down steel tubing 25mm to 32 mm bore including cleaning for refixing or removal to store, complete all as specified and directed by engr-in-Charge. |
| 38 | S&F 20mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified and directed by engr-in-Charge. |
| 39 | S&F 25mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc, complete all as specified and directed by engr-in-Charge. |
| 40 | Dismantling of 75 / 110mm bore cast iron ,PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches if reqd of any dia, complete all as specified and directed by engr-in-Charge. |
| 41 | S&f 75 mm bore PVC (SWR) pipe single socketed , in any length with rubber joints laid in trenches or in floors, complete all as specified and directed by engr-in-Charge. |
| 42 | S&F PVC (SWR) pipe 110 mm bore single socketed ,in any length with rubber ring joints,laid in trenches or in floors cement, complete all as specified and directed by engr-in-Charge. |
| 43 | S&f 75mm bore PVC (SWR) pipe bends any radius, complete all as specified and directed by engr-in-Charge. |
| 44 | S&F PVC (SWR) 110mm bore bends any radius, complete all as specified and directed by engr-in-Charge. |
| 45 | S&F PVC (SWR) 110mm bore junction single (single T), complete all as specified and directed by engr-in-Charge. |
| 46 | S&F 75mm borePVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed by engr-in-Charge. |
| 47 | M&L 75 mm bore PVC (SWR))multi floor trap with grating including jointing withsolvent cement, complete all as specified and directed by engr-in-Charge. |
| 48 | S&F PVC (SWR) 75mm bore vent cowl, complete all as specified and directed by engr-in-Charge. |
| 49 | S&F PVC (SWR) \"S\"trap 110mm bore for EWC/IWC, complete all as specified and directed by engr-in-Charge. |
| 50 | S&F in repairs viterous China wash down water closet pan (pedestal pattern white) (excluding flushing cistern and flush pipe) including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed by engr-in-Charge. |
| 51 | S&F in repair 10 ltrs capacity incl PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets & flush pipe, complete all as specified and directed by engr-in-Charge. |
| 52 | S&F in repair single piece china wash down water closet , with UF soft close seat cover, hinges, accessories set, cistern fittings size370x690x795mm Make: jaquar Cat No. KUSWHT-358515N or equivalant, complete all as specified and directed by engr-in-Charge. |
| 53 | S&F in repairsfor viterous china wash hand basinflat backsize 600x480mm excluding traps, waste , chain , plug and porcelain stopper incl brackets, complete all as specified and directed by engr-in-Charge. |
| 54 | S&Fin repairs 20mm bore bib taps fancey typechromium plated with capstan head chromium plated screwed down screwed for iron pipe or brass ferrule. (Minm wt 350 Gms), complete all as specified and directed by engr-in-Charge. |
| 55 | S&F in repairs 20mm bore stop cock fancy type chromium plated cast copper alloy screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and directed by engr-in-Charge. |
| 56 | S&F in repair piller taps 20 mm bore of cast copper alloy chromimum plated screwed down high pressure, hot aor cold long screwed shank fly nuts screwed to PP-R Pipesof any description, complete all as specified and directed by engr-in-Charge. |
| 57 | S&F in repairs wash hand basin table top type fixed on granite top grooving and cutting if requiredwith coloured sunmica sheet at all over withstainless steel legs at all corners, complete all as specified and directed by engr-in-Charge. |
| 58 | S&F in repair pillar tap fancy type single lever tall body with 150 mm extension body fixed on granite top for supply of hot or cold water fixeing with washers, complete all as specified and directed by engr-in-Charge. |
| 59 | S&F in repairs hand shower ( health faucet ) CP with 6-8 mm dia. and 1-1.5 metre long flexible tube and wall hook, complete all as specified and directed by engr-in-Charge. |
| 60 | S&F in repairs chromiumplated coloured/stainless steel paper holder fixed on walls, complete all as specified and directed by engr-in-Charge. |
| 61 | S&F in repairs angle valve (one way) 15 mm bore cast copper alloy fancy type, cromium plated with cup, complete all as specified and directed by engr-in-Charge. |
| 62 | S&F in repairs chromium plated brass bib tap fancy type screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore, complete all as specified and directed by engr-in-Charge. |
| 63 | S&F in repairsglass shelf corner in shape of arc/semicircle/triangular fixed on walls with screws, complete all as specified and directed by engr-in-Charge. |
| 64 | S&F in repairs chromium plated/ powder coated towel rack( 1-3 horizontal runners and 1 runner at bottom and min 2 hangers ) fixed to walls with screws, complete all as specified and directed by engr-in-Charge. |
| 65 | S&F in repairs CP brass towel ring(triangular/rectangular/circular) fixed and incl CP brass screws and, complete all as specified and directed by engr-in-Charge. |
| 66 | S&F in repairs Soap dish(coloured/powder coated) fixed with incl CP brass screws and complete all a specified and directed(Make Jaquar/Cera/ESS/Prayag or equivalent) |
| 67 | S&F in repairs chromimum plated brass 28-32 mm coupling for table top wash hand basin half or full thread with waste pipe of similar dia in pvc/plastic fixed, complete all as specified and directed by engr-in-Charge. |
| 68 | S&F in repairs PVC connections 15mm size with CP nuts of length 450-600mmand 3 layer protection of pipe with stainless steel wire mesh and double coated pvc pipe for hot and cold, complete all as specified and directed by engr-in-Charge. |
| 69 | S & F in repairs bevelled edge mirror of selected quality glass, fixed to wall with chromium plated brass spacer screws and cup wasers, complete all as specified and directed by engr-in-Charge. |
| 70 | S&F in repairs Harrision rails, anodised alloy, with fixing end brackets, stops, dooms etc complete set fixed on wall or wall pannels, complete all as specified and directed by engr-in-Charge. |
| 71 | S&F Grating doom 125 mm with waste hole of PTMT, complete all as specified and directed by engr-in-Charge. |
| 72 | S&F in repairs Tubular towel rail, 20mm dia, 60 cm long, CP with a pair of brackets, fixed to wall with CP brass screw and PVC rowl plugs (fixed in repair), complete all as specified and directed by engr-in-Charge. |
| 73 | S&F in repairsPVC waste pipe 32mm bore with cup and washers complete on new or old locations, complete all as specified and directed by engr-in-Charge. |
| 74 | Demolition brick work / block masonry or stone/ boulder masonry, built in built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed by engr-in-Charge. |
| 75 | Material and Labour precast cement concrete (using 20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonry with solid blocks,exc.10cm in width and setting in cement mortar 1:6, complete all as specified and directed by engr-in-Charge. |
| 76 | S&Fin repairs Sinksstainless steel with drainage board made of 1.0 mm thick kitchen or laboratory with plugs, washers and wastes; including fixing contilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed by engr-in-Charge. |
| 77 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive offixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed by engr-in-Charge. |
| 78 | S& F in repair 20 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed by engr-in-Charge. |
| 79 | S&F20in repairs PPR gate valve conforming to ISO 2000 screw down end for PPR pipe or for union and fixed completey as specified for the size 25mm bore, complete all as specified and directed by engr-in-Charge. |
| 80 | S&F25 in repairs PP-R Ball valves (brass insert) conforming to ISO 2000 screw down end for PPR pipe or for union and fixed completey as specified for the size 20mm bore, complete all as specified and directed by engr-in-Charge. |
| 81 | S&F18/19 mm thick PVC solid double side prelam celluca board of approved colour fixed with screws as in modular kitchen cabinets/cupboards including lipping portion match with laminated colour, complete all as specified and directed by engr-in-Charge. |
| 82 | S&F 100mm long extruded brass handles, fabricated type polished, complete all as specified and directed by engr-in-Charge. |
| 83 | S&F 30mm width of flaps(when open) continous (piano) hinges, brass, complete all as specified and directed by engr-in-Charge. |
| 84 | S&F magnetic catcher with 8mm dia ball and brass body and stricking plate, complete all as specified and directed by engr-in-Charge. |
| 85 | Dismanteling of Stone slabs and tiles of any description or thickness in floors, aprons etc., complete all as specified and directed by engr-in-Charge. |
| 86 | M&L for Granite 16 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite black, complete all as specified and directed by engr-in-Charge. |
| 87 | Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members, complete all as specified and directed by engr-in-Charge. |
| 88 | M & L for providing and fixing Gypsum boards 7-9 mm thick PVC film on the face side and other side metalised polyster flim asin ceilings fixed with screws as per manufacturers instructions including anodised aluminium powder coated snap grid frame work of size 605 x 605 mm with anodised aluminium channel supports/ angles/ \"T\" (Main tee 35 x 25 x 1.5 mm, cross tee 25 x 25 x 1.4 mm and wall angle 32 x 32 x 2 mm) fixed with screws/ plugs etc including GI suspenders of 6mm dia upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size as per approved pattern and design, complete all as specified and directed by engr-in-Charge. |
| 89 | M&L for 7-10mm thick teak wood finish laminatedwooden flooring interlocked with each others and its size as directed,over6 micron polyethylene sheeting over the concrete to minimize moisture migration from the concrete including dismantling, complete all as specified and directed by engr-in-Charge. |
| 90 | S&F of wooden panelling on vertical surface of wall using following specifications complete all as specified and directed incl dismantiling of old :-(a) S&F Iind class hard wood wooden gutties of size 25mmx25mmx200mm depth fixedin wall by making holes in brick wall and making good in cement mortar 1:3.(b)S&F horizontal rummer Iind class soft wood(Kali( at 120 c/c of sextional area exc. 13 Sqm and n. exc 25 Sqm clean sawn treated with two coats of creoste oil mixed with good quality pesticide for antitermite treatment.(c) S&F 1st cl soft wood (Deodar) boarding 12mm to 15mm thick as in wall panelling planed one side, wrought and other side clean sawn and applying two coats of good quality varnish on plain surfaces ofve a coat of primer mixed with good quality pesticide for antitermite treatment on the other side and fixed with screws/nails on wooden runners, complete all as specified and directed by engr-in-Charge. |
| 91 | M&L for 2nd class softwood clean sawn as in scantling fixed with nails exceeding 13 Sqcm and n.exc 25 Sqcm in section, complete all as specified and directed by engr-in-Charge. |
| 92 | Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil, complete all as specified and directed by engr-in-Charge. |
| 93 | Excavating in trenches, n exc .5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense soil, complete all as specified and directed by engr-in-Charge. |
| 94 | M&L PCC 1:4:8 Type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed by engr-in-Charge. |
| 95 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed by engr-in-Charge. |
| 96 | Removal excavated material exc 250m and n.exe 500manddepositing where directed at a level n.exc 1.5 m above the starting point, complete all as specified and directed by engr-in-Charge. |
| 97 | M&L for Reinforced Cement Concrete (design mix) M-25 using 20 mm graded aggregate for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by engr-in-Charge. |
| 98 | M&L for Reinforced Cement Concrete (design mix) M-25 using 20 mm graded aggregate for Slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by engr-in-Charge. |
| 99 | M&L for Reinforced Cement Concrete (design mix) M-25 using 20 mm graded aggregate for Columns, pillars, piers, posts and struts, complete all as specified and directed by engr-in-Charge. |
| 100 | M &L for Formwork to Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter fair finished, complete all as specified and directed by engr-in-Charge. |
| 101 | M &L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed by engr-in-Charge. |
| 102 | M& L for Formwork to sides of pillars, posts, struts, piers, columnsand stanchions fair finished, complete all as specified and directed by engr-in-Charge. |
| 103 | S&F for Mild steel bars Mild steel bars 10mm dia and over, cut tolength, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia orsecuring with clips, complete all as specified and directed by engr-in-Charge. |
| 104 | All as per item No. above here-in- before but up to and including 6 to 8 mm dia in stirrups, spacersand binders as in columns and beams etc., complete all as specified and directed by engr-in-Charge. |
| 105 | M&L for laying 100mm thk PCC, type B- 2, 1:2:4 using 40mm graded aggregate, complete all as specified and directed by engr-in-Charge. |
| 106 | M&LDistempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification with Two or more coats on new work over a coat of primer over a coat of 3mm thk wall care putty on plastered surface of any description,including preparation of new plastered surface, complete all as specified and directed by engr-in-Charge. |
| 107 | M&L for Non - skid joint free coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match jointed in 15mm thk screed bed in CM 1:4 and pointed in white cement to match, complete all as specified and directed by engr-in-Charge. |
| 108 | M&L for RCC M-25(Design Mix) using 20mm graded aggregate in lintels over 1.5m span, complete all as specified and directed by engr-in-Charge. |
| 109 | M&L for Type B1(1:2:4) using 20mm graded aggregate in lintels upto 1.5m span, complete all as specified and directed by engr-in-Charge. |
| 110 | S&F Anodised powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and directed by engr-in-Charge. |
| 111 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprenepacking,handles 2 Nos in each door, hinges,anodised aluminum snapbeading screws etc., complete all as specified and directed by engr-in-Charge. |
| 112 | S&F Anodised aluminium window andventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., complete all as specified and directed by engr-in-Charge. |
| 113 | M&L for plain sheet glass 4.80mm thick ordinalry quality and glazing with oil putty or wooden beads in square or fixed with aluminium section including rubber beads not exc 0.50 sqm in each pane complete all as specified and as directed by Engr-in-Charge. |
| 114 | S&F Framed work as in doors or gates of angle or other section with gussetplates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing, complete all as specified and directed by engr-in-Charge. |
| 115 | Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with ashers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long |
| 116 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by engr-in-Charge. |
| 117 | M&L for preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth, not other wise decribed and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by engr-in-Charge. |
| 118 | S&F Door closer hydraulically regulated designation No 3 universal type, aluminium body suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixedand fixed, complete all as specified and directed by engr-in-Charge. |
| 119 | S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms), complete all as specified and directed by engr-in-Charge. |
| 120 | S&F Plates (plain or chequered) channels with Fe 410 -W (Gde- E- 250) quality- A, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, complete all as specified and directed by engr-in-Charge. |
| 121 | S&F hand shower ( health faucet ) CP with 6-8 mm dia. and 1-1.5 metre long flexible tube and wall hook, complete all as specified and directed by engr-in-Charge. |
| 122 | S&F Vitreous China Full stall urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixingautomatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified and directed by engr-in-Charge. |
| 123 | S&F single piece china wash down water closet , with UF soft close seat cover, hinges, accessories set, cistern fittings size370x690x795mm, complete all as specified and directed by engr-in-Charge. |
| 124 | S&Fwash hand basin table top type fixed on granite top grooving and cutting if requiredwith coloured sunmica sheet at all over withstainless steel legs at all corners complete all as specified and directed. Size of the table top to be min (0.81 x 0.60 x 0.76 m ) as l x b x h in dimensions, complete all as specified and directed by engr-in-Charge. |
| 125 | S&Fchromium plated paper holder fancy type(rectangular/circular)screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore, complete all as specified and directed by engr-in-Charge. |
| 126 | S&F angle valve (one way) 15 mm bore cast copper alloy fancy type, cromium plated with cup, complete all as specified and directed by engr-in-Charge. |
| 127 | S&Fchromium plated brass bib tap fancy type screwed down ,screwed for iron pipe or for brass ferrule 15 mm bore, complete all as specified and directed by engr-in-Charge. |
| 128 | S&F glass shelf corner in shape of arc/semicircle/triangular fixed on walls with screws, complete all as specified and directed by engr-in-Charge. |
| 129 | S&F chromium plated/ powder coated towel rack( 1-3 horizontal runners and 1 runner at bottom and min 2 hangers )fixed to walls with screws, complete all as specified and directed by engr-in-Charge. |
| 130 | S&F CP brass towel ring(triangular/rectangular/circular) fixed and incl CP brass screws, complete all as specified and directed by engr-in-Charge. |
| 131 | S&F Soap dish(coloured/powder coated) fixed with incl CP brass screws, complete all as specified and directed by engr-in-Charge. |
| 132 | S&F chromimum plated brass 28-32 mm coupling for table top wash hand basin half or full thread with waste pipe of similar dia in pvc/plastic fixed , complete all as specified and directed by engr-in-Charge. |
| 133 | S&F PVC connections 15mm size with CP nuts of length 450-600mmand 3 layer protection of pipe with stainless steel wire mesh and double coated pvc pipe for hot and cold, complete all as specified and directed by engr-in-Charge. |
| 134 | S&F25 in PP-R Gate valves (brass insert) conforming to ISO 2000 screw down end for PPR pipe or for union and fixed, complete all as specified and directed by engr-in-Charge. |
| 135 | S&F25 s PP-R Ball valves (brass insert) conforming to ISO 2000 screw down end for PPR pipe or for union and fixed, complete all as specified and directed by engr-in-Charge. |
| 136 | S&F 25mm Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms), complete all as specified and directed by engr-in-Charge. |
| 137 | S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed by engr-in-Charge. |
| 138 | S&F 110 mm dia PVC (SWR) vent cowl, complete all as specified and directed by engr-in-Charge. |
| 139 | S&F bevelled edge mirror of selected quality glass,mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cupwashers, complete all as specified and directed by engr-in-Charge. |
| 140 | M &L, Soakage well of 3.0 mtr internal dia at top and min 1.80 mtr dia at bottom having min 2.45 mtr height of 380mm thick random rubble uncoarsed stone masonary wall in CM 1 :6 with 150mm thick PCC 1 : 4 :8, type D-2 (using 40 mm graded stone aggregate) below stone masonary at bottom and RCC slab using design mix M-25 with reinforcement 10mm dia bars @ 150mm C/C bothways cranked at 1/4 th of span including arrangement for manhole opening and manhole cover, inlet for 100 /150mm dia pipe and rest all as sfd as per Drg No CESZ/TD-1078/2011 sheet 1/1 Note :-The rate including excavation in hard/dense soil and construction of soakage well as per drg, connection of inlet pipe, 100 mm dia PVC vent pipe with cowl, returning filling and removing of surplus soil to a distance exc 50 mtr but n.exc 100 mtr from site. |
| 141 | S&F, 150mm dia bore (inner dia) double wall corrugated HDPE Pipe (SN-8) in any length including all fittings and jointing with eastomeric rubber link and cuppler /other jointing materials laid in trenches are in floors, complete all as specified and directed by engr-in-Charge. |
| 142 | M&L for providing cement concrete 1:3:6type C-2 bed to 150mm bore of drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for, complete all as specified and directed by engr-in-Charge. |
| 143 | M&L for providing precast reinforced cement concrete type A1, 1:1.5:3 using 20mm graded aggregate as in landings, cover slabs (for man holes etc) and similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match including use of necessary formwork, complete all as specified and directed by engr-in-Charge.Note : S&F reinforcement shall be measured and paid separately. |
| 144 | M&L for point wiring with copper conductor cable, multistranded, single core 1.5 Sqmm size for one light point controlled by one switch with PVC insulated multistranded copper conductor cable FRLS of size 1.5 sq mmfor earth continuity i drawn through PVC rigid non metallic conduitconcealedof approved size and quality fixed on walls/ceiling/wooden panelling including fixingmodularPVC/ MS terminal boxes with top cover plate for fixing modular switch socket etc and all fittings for wiring work to be carried out for modular fittingsonas per site reqmnt of any size complete all as directed and specified.Note- Cost of terminal box and Modular cover plate are inclusive in quoted rates. Colour of plate and switch approved by Engr-in-Charge as per site requirement. |
| 145 | All as per Item No 144, but forone 3 pin socket outlet, 5 Ampson the same board with other switches, with cables1.5 Sqmmsize, complete all as specified and directed by engr-in-Charge. |
| 146 | All as per Item No 144,but forone 3 pin socket outlet, 5 Amps Independent with cables1.5 Sqmmsize, complete all as specified and directed by engr-in-Charge. |
| 147 | All as per item No 144,above but for3pin 15 Amps socket outlet independent with copper conductor cable PVC insulated multistrand 2.5 Sqmm with 2.5 sqmm PVC copper conductor as earth wire connected to earth dolly, complete all as specified and directed by engr-in-Charge. |
| 148 | M&L forModular switch colour white/Golden one way single pole 6 Amp 1 module 240 volts, complete all as specified and directed by engr-in-Charge. |
| 149 | M&L for Modular switch colour white/Golden one way single pole 16 Amp 1 module 240 volts, complete all as specified and directed by engr-in-Charge. |
| 150 | S&F forModular colour white/Golden socket 6/16 A -2/3 Pin combined 2 module 240 Volt, complete all as specified and directed by engr-in-Charge. |
| 151 | S&F Modular socket colour white/Golden6 A -2/3 Pin combined 2 module 240 Volt, complete all as specified and directed by engr-in-Charge. |
| 152 | S&F decorative ultra slim square profileLED lighting fixture with extruded aluminium , energy efficient ready to use pack 18Watts LED 6000Kof White/ Warm whitecolour with connection 3 core copper wire from ceiling rose to fitting with complete accessories, complete all as specified and directed by engr-in-Charge. |
| 153 | S&F decorative ultra slim square profileLED lighting fixture with aluminium extruded , environmental friendly energy efficient ready to use pack 9/10Watts LED 6000K with connection 3 core copper wire from ceiling rose to fitting with complete accessories, complete all as specified and directed by engr-in-Charge. |
| 154 | S&FLED36 watts recessed 2x2 luminaire Warm White to enhance the delight of occupants with comfortable experence through its design & glare free soft illumination andconnection of 3 core copper wire with all accessories complete, complete all as specified and directed by engr-in-Charge. |
| 155 | S&F MCB DB SPN 8 Way double door 240Volt 50Hz with complete accessories, complete all as specified and directed by engr-in-Charge. |
| 156 | S&F MCB SP 6 to 32 Amps \"C\" series, complete all as specified and directed by engr-in-Charge. |
| 157 | S&F MCB SPN 40-63 Amps \"C\" series, complete all as specified and directed by engr-in-Charge. |
| 158 | S&F forsub main wiring with 2 runs of FRLS PVC insulated multistrand, copper conductor cable of size 2 x 10 sq. mm +1x 10 sqmm PVCinsulated cable 1100 volts multi stranded copper conductor as earth wiredrawn through PVC non metallic conduit, complete all as specified and directed by engr-in-Charge. |
| 159 | Supply and fix Air circulator made of sturdy Engineering plastic complete with louvers, shutter, voltage 230 volt, 50 Htz RPM 1200, copper winding of sweep 250 mm, complete all as specified and directed by engr-in-Charge. |
| 160 | Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc, complete all as specified and directed by engr-in-Charge. |
| 161 | M&L for point wiring with copper conductor FRLS cable Multistrand, single core 1.5 Sqmm size for one light point or bell point /Ex: fan Pointcontrolled by one switch including one run of 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping of approved size and quality fixed on walls/ceiling including rectangular PVCboard heavy duty type for mountingswitches /sockets etc, complete all as specified and directed by engr-in-Charge. |
| 162 | All as per item No 161,but for 5 AmpsSocket outlet in same Board with 1.5 sq mm cable, complete all as specified and directed by engr-in-Charge. |
| 163 | All as per Item No 161, but for 5 Amps Switch Socket Combination in independent board with 1.5 Sqmm Cable, complete all as specified and directed by engr-in-Charge. |
| 164 | All as per item No 161,above but for power point 3/5 pin switch socket 15 Amp with PVC copper conductor cable FRLS multistrand unsheathed 2.5 Sqmm on independent board incl one run 2.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall incl includingPVC box 2 mm, complete all as specified and directed by engr-in-Charge. |
| 165 | Supply and fixing in replacemetn piano switch single pole one way6 Amps, complete all as specified and directed by engr-in-Charge. |
| 166 | M&L in replacement Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal, complete all as specified and directed by engr-in-Charge. |
| 167 | M&L in replacement of switch socket combination 5 amp-2/3 pin, complete all as specified and directed by engr-in-Charge. |
| 168 | M&L in replacement ofsocket outlet 5 amp -2/3 pin, complete all as specified and directed by engr-in-Charge. |
| 169 | Supply and fix as in repair decorative durable LED batten fitting 18 Watt , 4feet long with decorative and caps, powder coated CRCA decorative for LED tube 1x18 W LEDincluding LED retrofit , 4 feet long (white colour) tube of 18 watt having driver ,connector block etc complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core, complete all as specified and directed by engr-in-Charge. |
| 170 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by engr-in-Charge. |
| 171 | S&F in replacement of old U/S Lamp LED 7 Watt, 230 volts 50 Hz AC, complete all as specified and directed by engr-in-Charge. |
| 172 | S & F in replacement LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by engr-in-Charge. |
| 173 | M&L for ceiling rose surface bakelite 65x50 mm two to three terminals, complete all as specified and directed by engr-in-Charge. |
| 174 | M&L in replacement for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed by engr-in-Charge. |
| 175 | Supply and fix in replacement of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm sweep all as specified and directed. |
| 176 | S&F in replacement of Old UNSV sheet metal enclosure SPN for DBs with 200 Amps bus bar of 8 way 240 volts with blank plate Double Door, complete all as specified and directed by engr-in-Charge. |
| 177 | S&F in replacement of Old U/S MCB single phase (SP), 6 to 32 Amps 240 Volts C Curve, complete all as specified and directed by engr-in-Charge. |
| 178 | S&F in replacement of old MCB SPN,C- curve, 230 volt40-63 amp 10KA, complete all as specified and directed by engr-in-Charge. |
| 179 | M&L in replacement for sub main wiring with 2 runs of FRLSPVCinsulated multistrand, copper conductor cable of size 6 Sqmm along with one run of 6 sqmm PVCinsulated cable 1100 volts multi stranded copper conductor as earth wire in and including PVC casing & capping, complete all as specified and directed by engr-in-Charge. |
| 180 | Supply and fixing XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm2 Core, complete all as specified and directed by engr-in-Charge. |
| 181 | Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected using galvanised iron strip 25×4mm as earthing leadby means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 40mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test pointetc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and directed by engr-in-Charge.Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces. |
| 182 | Deduct Schedule of Credit of Rs (-) 36288.00 (Minus) as listed in Schedule \"A\" (Contd). Contract Sum shall be arrived after deducting the credit amount.Note :- Tenderers will not quote against this item being a firm amount. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
