|
| 1 | Part ASupply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. UPPWD schedule 2018.item no.641.=(1x715=715nos) |
| 2 | Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130 mm and base plate 12mm thik) having 3mm thikness with Double arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect. UPPWD schedule 2018.item no.642.=(1x46nos) |
| 3 | Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.UPPWDschedule2018.item no.645 |
| 4 | Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 protection complete in all respect..UPPWD schedule 2018.item no.1423 cat.AAA (1x715+1x46x2=807nos) (on pole with required wire submains connectionsetc as per Engineer incharge) with five year warranty |
| 5 | Supply and fixing of L.E.D. street light fitting having die cast aluminium body and fiffuser with driver set suitable for 110watt 130 watt confirming to IP 66 including G.I. pipe and bracket on pole with clamps complete in all respect as per direction of E/I S.I. 1424 (2018) cat..AAA |
| 6 | Supply & fixing of 12.5 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect.Bajaj ,philips, crompton,equivalent =(1x9=9nos) |
| 7 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 100to 120 Watt. Confirming to IP 65 protection complete in all respect. =(1x9x6=54nos)UPPWD schedule 2018.item no.1453 cat.AAA with five year warranty |
| 8 | upply & fixing of 16 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 360 mm base plate 32 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect. . |
| 9 | Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140to 150 Watt. Confirming to IP 65 protection complete in all respect.UPPWD schedule 2018.item no.1454 cat.AAA with five year warranty |
| 10 | Supply and laying of 10sqmm x4c almunium conductor PVC insulated aromoured served Sheathed cables 11 Volts grade of A depth of 750 mm below ground level over a caution of 75mm. thick sand alround and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on MS Clamps etc. of suitable size or as directed by Engineer-Incharge, complete in all respect. the armouring of the cables shall be properly connected with the earth conductor by clamping etc.a- 4Cx10sqm (S.I. 501(I)/2018 (327-170=157) |
| 11 | Supply and laying of 25sqmm x3.5c almunium conductor PVC insulated aromoured served Sheathed cables 11 Volts grade of A depth of 750 mm below ground level over a caution of 75mm. thick sand alround and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on MS Clamps etc. of suitable size or as directed by Engineer-Incharge, complete in all respect. the armouring of the cables shall be properly connected with the earth conductor by clamping etc. |
| 12 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all aceesories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, Jointing etc.direct in ground(75cm below ground level), including excavation and refilling the trench but excluding sand cushioning and protective covering etc complete as required. 63mm dia (OD-63 mm& ID-51 mm nominal (S.I. No. 14.16a) CPWD/2018 |
| 13 | Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. |
| 14 | Supply and fixing of 4sqmm plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. |
| 15 | Supply and burying of 40mm dia x 4.5 neters long G.I. Pipe vertically for earthing havin 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cot of G.I. wire and pipe will be extra) upto switch board, 30 cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate laters of charcoal/coke and salt at least 150mm thick alround etc. as per direcions of Engineer-in charge coplete in all respects as per drawing..item no 701 uppwd |
| 16 | Supply and fixing capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contractors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect 40 A TPN SOR-807(f)(ii)/2018,inbuild three nos timer phasewise |
| 17 | Supply and fixing of 4Cx10 Sqmm brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer Incharge. |
| 18 | Supply and fixing of 10sqmm plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. |
| 19 | making suitable earthing of H.T pole with 2.5 Mt long 20mm dia M.S. rod 7/16 of 6 SWG G.I. wire including the cost of all material labour T&P etc. required for proper completion of the work. AR ( As per UPPCL cost shedule 2018-19 ) |
| 20 | S/F of 100mm dia class B G.I. pipe including supply & fixing of suitable size M.S. clamps with bolts and sealing of ends of pipes and nuts complete in all respects. AR S.I. No.12.39 CPWD 2018 |
| 21 | Part -B for New LightOnly For Operational Charge For One Year (0.50%) On Part-A |
| 22 | 2nd Year (0.5%) Operation Charge On Part-A |
| 23 | 3rd Year (.75%) Operation & Maintanance Charge On Part-A |
| 24 | 4th Year (1%) Operation & Maintanance Charge On Part-A |
| 25 | 5thYear (1.25%) Operation & Maintanance Charge On Part-A Please Enable Macros to View BoQ information |
