|
| 1 | M & L for repair, servicing and overhauling of flame-proof EOT cranes of capacity 1.5 Ton to 3 Ton, installed at heights ranging from 5.0 m to 15.0 m above the working level, including thorough greasing, oiling, cleaning of the crane, and repair/replacement of defective parts, removal and deposition of unserviceable parts to MES store yard, complete all as specified and directed by the Engineer-in-Charge.Notes:(i) Replacement of unserviceable parts shall be measured and paid separately under respective “supply only” items.(ii) Labour required for replacement of unserviceable parts shall be deemed to be included in the unit rate quoted for this item. |
| 2 | M & L for repair, servicing and overhauling of manually operated gantry cranes of capacity 1.5 Ton to 3 Ton, installed at heights ranging from 7.0 m to 10.0 m above the working level, including thorough greasing, oiling, cleaning of the crane, and repair/replacement of defective parts, complete all as specified and directed by the Engineer-in-Charge.Notes:(i) Replacement of unserviceable parts shall be measured and paid separately under respective “supply only” items.(ii) Labour required for replacement of unserviceable parts shall be deemed to be included in the unit rate quoted for this item. |
| 3 | Supply only the following Spare parts/ Components of EOT Cranes/ Hoists/ Manual Operated gantry of capacity1.5 to 3 Ton. |
| 4 | Brake oil for top-up |
| 5 | Gear oil 90 grade as per IA 8406/1993 |
| 6 | Carbon Brushes. |
| 7 | Over Load Relay 5 to 20 Amps |
| 8 | Brake Lining. |
| 9 | Magnetic Coil. |
| 10 | Oil Seal. |
| 11 | Gasket. |
| 12 | Brake Shoe |
| 13 | Brake for LT/CT Coil. |
| 14 | Pedant Push Button . |
| 15 | Key Switch |
| 16 | Indicator Lamp (RYB) |
| 17 | Indicator Bulb |
| 18 | Kit kat fuse assembly complete of32 amps capacity |
| 19 | Push Button with auxiliary contacts NO/NC. |
| 20 | No Volt Coil 110 Volts AC suitable for 40 Amps Contactor. |
| 21 | Rotary switch three phase |
| 22 | HRC Fuse 02 Amp to 32 Amps. |
| 23 | Digital volt meter |
| 24 | Cable carrier 8/10mm |
| 25 | Roller Bearing. |
| 26 | Gear Wheel. |
| 27 | Clutch plate with assembly |
| 28 | Remote control 4 way |
| 29 | Single phase preventer |
| 30 | Three phase step down Transformer 440/110 Volts. |
| 31 | Four Pole Contactor 32 Amps, 110 Volts coil voltage. |
| 32 | Four Pole Contactor 16 Amps, 110 Volts coil voltage. |
| 33 | TP Contactor 32 Amps, 110 Volts coil voltage ML-3. |
| 34 | TP Contactor 16 Amps, 110 Volts coil voltage ML-2. |
| 35 | LT Cable 2.5 Sq mm, 4 Core Copper Conductor. |
| 36 | Copper conductor 1.5 Sqmm, 16 core, 1100 volts grade PVC sheathed. |
| 37 | Steel Wire Rope 8 to 12 mm dia. |
| 38 | Chain for pulley 20/25mm |
| 39 | Pulley 20/25mm |
| 40 | End carriages |
| 41 | M & L for rewinding and overhauling of electric motor removed from cranes or air curtains, including disconnecting and transporting to workshop, taking out old winding, rewinding with same gauge of super-enamelled copper wire, varnishing, overhauling, refitting to crane, connecting and testing on completion, complete all as specified and directed for the following capacity. |
| 42 | Capacity 01 HP/ 02 HP Motor |
| 43 | Capacity up to 3 HP Motor |
| 44 | Capacity up to 5 HP Motor |
| 45 | M & L for load testing of 1.5 Ton and 3 Ton capacity EOT/HOT cranes with 25% overload, all as specified in IS: 3177–1977 and IS: 3938–1977, including recording and marking the date of load testing on the crane, complete all as directed by the Engineer-in-Charge.Note: Contractor shall arrange necessary load materials and furnish a certificate confirming the crane is serviceable and fit for operation. The certificate shall remain valid for one year from the date of completion of work. |
| 46 | M & L for complete cleaning and painting of 1.5 Ton to 3 Ton capacity EOT cranes, installed at heights between 5.0 m to 15.0 m from working level, including thorough removal of dirt, grease, scale, and rust by shot blasting or chemical cleaning, removal of old paint, and applying:(i) One coat of approved primer to all exposed metal surfaces;(ii) Two coats of synthetic enamel / epoxy paint (indoor/outdoor type as approved by GE);(iii) One coat of rust inhibitor on bright exposed metal parts; and(iv) One coat of oil-resistant paint inside all gearboxes.Also, writing technical details and data on each crane with approved paint, complete all as specified and directed by the Engineer-in-Charge. |
| 47 | S & F in replacement of complete gearbox for 1.5 Ton to 3 Ton EOT crane, of any make or description, including taking down unserviceable unit, fixing new gearbox in position, alignment and testing on completion, complete all as specified and directed.Make: The make shall be as per the existing make/ model for better compatibility. |
| 48 | Disconnecting, opening and replacement of existing VFD (driver unit) of EOT crane control panel with new one of same make and model, reassembling, wiring, and testing on completion, complete all as specified and directed. |
| 49 | S & F in replacement of flame-proof pendant type controller, 8 to 12 way, suitable for 1.5 Ton to 3 Ton EOT cranes, including disconnection, removal of existing unit, fixing and testing on completion, complete all as specified and directed.Make: The make shall be as per the existing make/ model for better compatibility. |
| 50 | S & F in replacement of flame-proof limit switch (lever type) suitable for 1.5 Ton to 3 Ton EOT cranes, including removal of defective unit, fixing, connection, and testing on completion, complete all as specified and directed.Make: The make shall be as per the existing make/ model for better compatibility. |
| 51 | S & F in replacement of electro-hydraulic thrustor, 18 Kg capacity, suitable for three-phase 400/440V power supply, including removal of existing unserviceable thrustor, installation, wiring, and testing of the crane on completion, complete all as specified and directed. |
| 52 | Taking down un-serviceable sub mainwiring of aluminium etc. and making good the disturbed surfaces of walls/ floor etc. for matching with the existing surface. |
| 53 | Taking down existing flame-proof rotary switch, metal plug socket or main switch, of any size or rating, including disconnection, removal, making good the disturbed surfaces of wall or floor, and providing temporary power supply during the work, complete all as specified and directed. |
| 54 | Taking down carefully MCB of all type complete and making good disturbed surface of wall/ floor, etc. complete all as specified and as directed.Note: Temporary power supply shall be arranged by contractor. |
| 55 | M & L for surface sub main wiringwith two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 1.5 sqmm (Nominal area) drawn through in and including steel conduitsize with all fittings and accessories along with one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dollyincl dismantling taking down old unserviceable wiring and making good to disturbed surfaces all as specified and directed. NOTE: (a) Two run of cable with one run of earth wire and one run of steel conduit will be measured as one length. |
| 56 | All as per item No 15 here-in-beforebutcable of size 2.5 sqmm all as specified and directed. |
| 57 | All as per item No 15 here-in-beforebutcable of size 4.0 sqmm all as specified and directed. |
| 58 | All as per item No 15 here-in-beforebut cable of size 6.0 sqmmall as specified and directed. |
| 59 | S & F of flame proof rotary type switch with termination box in LM6, 16A, single pole 250V complete all as specified and as directed. |
| 60 | S & F of flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth complete all as specified and as directed. |
| 61 | S & F flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth complete all as specified and as directed. |
| 62 | S & F of MCB distribution board, Double door, metal enclosure, SPN, 230 Volts,8 way including taking down of old DBs all as specified and as directed. |
| 63 | S & F of MCB distribution board, Double door, metal enclosure, VTPN, 415 Volts, 4 wayincluding taking down old DBs complete all as specified and directed. |
| 64 | S&Fflame proof,weather proof MCB distribution board, 230 Volts, 8 way SPNincluding MCB and taking down old unsv DB complete all as specified and directed. |
| 65 | S & F of flame proof,weather proof MCB distribution board,440 Volts, 4 wayTPN including MCB and taking down old unsv DBs complete all as specified and directed. |
| 66 | S & F of MCB, Single Pole, 6 to 32 amps, 240 volts, 10 kA breaking capacity, \"C\" curve complete all as specified and as directed. |
| 67 | S & F of MCB, Double Pole, 6 to 32 amps, 415 volts, 10 kA breaking capacity, \"C\" curve complete allas specified and as directed. |
| 68 | S & F of MCB, Four Pole, 40 to 63 amps, 415 Volts complete all as specified and directed. |
| 69 | S & F of LED tube rod polycarbonate body, 20 watt retrofit PF 0.9 suitable for 4 feet flame batten, complete wiring with 0.5 sqmm copper flexible conductor, connecting up to ceiling rose including taking down of old fitting complete all as specified and directed. |
| 70 | S & F of flame proof batten suitable for single tube rod (1x20 W) CMRI certifiedrecommended for gas/ vapour group of IIA &IIIB, Zone 1 & 2 and IP 65 Protection with die cast aluminium housing with heat resistant toughened glass with all accessories prewired and including connecting up to ceiling rose incl taking down old unsv fitting complete all as specifiedand directed by Engr-in-Charge. |
| 71 | All as per item No. 30 above but flame proof batten suitable for2X20 watt tube rod. |
| 72 | S & F of flame proof LED light fitting 40 watt CMRI certified and recommended for Gas Group IIC, Zone 1 and 2, temperature Class T6, IP 65 Protection with die cast aluminium housing with heat resistant toughened glass with all accessories prewired incl taking down old unsv fitting complete all as specified and as directed by Engr-in-Charge. |
| 73 | Labour only for disconnecting LT cable of any size from pole box/ panel/ DB and re-connecting of cable at both end after removing carbon/ burnt insulation part of cable by cutting, refixing cable with new cable lugs, getting out cable loop from the ground by digging and returning and filling the soli, making good the disturbed surface complete all as specified and as directed.Note : Digging for cable loop and including making good the disturbed surface by filling soil will be inclusive in quoted rate. |
| 74 | S & F of PVC junction box with aluminium bus bar of size (30x25x15cm) with 6 Amp MCB SP fixing in position with nut, bolt, clamp and taking out old unsv box complete all as specified and directed. |
| 75 | M & L for three core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn through PVC Conduit andOH line/ street light to pole box incl dismantling/ taking down old unserviceable wiring and making good to disturbed surfaces complete all as specified and directed. |
| 76 | S & F of GI tubing light grade 50mm bore with necessary clamps, nuts, bolts and washers for holding dispersal light/ cable protection , ISI marked incl dismantling/ taking down unserviceable ones complete all as specified and directed. |
| 77 | Servicing/ cleaningto air curtain and repair/ replacement of defective parts and reassemble air curtain and testing complete all as specified and directed by Engr-in-Charge.Note: Minor part including Labour required for the replacement of unserviceable items shall be deemed to be included in the unit rate quoted against this item. |
| 78 | S & F of obstruction light fitting 20 watt complete with all fittings incl 1.5 sqmm three core copper flexible conductor cable including taking down same light fitting of any type and from any position complete all as specified and directed. |
| 79 | S & F of amber target light fittings 20 watt complete with all fittings incl 1.5 sqmm three core copper flexible conductor cable incl dismantling/ taking down same light fitting of any type and from any position complete all as specified and directed. |
| 80 | S & F of Go-No-Go display lightcomplete with all fittings incl 1.5 sqmm three core copper flexible conductor cable incl dismantling/ taking down same light fitting of any type and from any position complete all as specified and directed. |
