Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thickin cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cementincluding mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of Oil Based Bituminous Primer conforming to IS – 3384 [Latest] @ 0.3 Litre / Sq.m, laying APP Modified [Polyester Reinforced] Membrane of 3mm thick weighing not less than 3.8 KG / Sq.m confirming to IS – 16532 [2017], by torch application with side overlap of 100mm & end overlap of 150mm & tucked into the chases on vertical surfaces by thermo fusion and finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top for water proofing treatment complete including taking down existing Roof Treatment of any description and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately. |
| 2 | Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exceeding10 cm girth and not exceeding 20 cm brick walls complete all as specified and as directed. |
| 3 | M & L for PCC 1:2:4, Type B-0, using 10mm graded aggregate as in Sub base for flooring / Levelling Course / Padding over roof slabs & Haunching etc., laid to required slope complete all as specified and as directed. |
| 4 | Supply only Integral Water Proofing Compound [ISI marked] of approved make complete all as specified and as directed. |
| 5 | Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.meach and removing to store complete all as specified and as directed. |
| 6 | Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each and removing to store complete all as specified and as directed. |
| 7 | Taking down shutter of size exceeding 1 Sq.m but not exceeding 2 Sq.m each and refixing in the same opening after easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. complete all as specified and as directed. Note: Renewal of Builder\"s Hardware Articles, if specially ordered, shall be paid for asSupply only under relevant Items of this BoQ. |
| 8 | S & F Second Class Hard Wood, Plain, Solid, Straight Chowkats and Frames, Wrought, Framed, Rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints complete all as specified and directed. |
| 9 | S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed. |
| 10 | M & L for providing Cement Concrete, Type C1, 1:3:6 using 20mm Graded Aggregate as in Lintels up to 1.5m Clear Span, Cills, Steps, Seismic and other Similar Bands, Plinth Courses, Copings, Bed Plates etc. complete including necessary formwork complete all as specified and as directed. |
| 11 | S & F Factory made, 35mm thick, Second Class Hard Wood, Plain framed, Panelled Shutter [Two Panel] with Lock Rail and Panel of 9 mm BWP Commercial Ply or 12 mm Veneered Particle Board with Commercial Veneering on both faces, the size of Rail and Stile as per IS – 1003 [Part – I], Kiln Seasoned and Chemically Pressure treated and fitted to Chowkats complete all as specified and as directed. |
| 12 | S & F Factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., Divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed. |
| 13 | M & L for preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 14 | M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. |
| 15 | S & F Solid PVC Door Frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per Specification & Drawing shown on Serial Page No. 160 of MES Schedule Part - II complete all as specified and as directed. |
| 16 | S & F Factory made Solid Panel PVC Door Shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC \"C\" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing shown on Serial Page No. 157 of MES Schedule Part - II complete all as specified and as directed. |
| 17 | S & F 125 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and as directed. |
| 18 | S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed. |
| 19 | S & F Aluminium anodised barrel Tower Bolt of size 100 mm size of extruded section complete all as specified and as directed. |
| 20 | S & F Aluminium anodised Handle, Cast Type, of size 150 mm complete all as specified and as directed. |
| 21 | S & F Hasp and Staple, safety type of aluminium anodised including bolt to hinge plate, fixed with screws of 100mm size complete all as specified and as directed. |
| 22 | S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 23 | S & F Factory made UPVC Sliding Window, Three Track, White Colour of any size, made of extruded profiles with wall thickness of 2.3mm±0.2mm, Window profile with hollow section with multi chamber, Frame of size 88mm X 52mm, Sliding Sash of size 42mm X 67mm, Sliding Mesh Sash of size 42mm X 57mm, Sliding Interlock [One vertical length in each shutter] of size 45.50mm X 28mm, Glazing Bead of size 24.50mm X 16mm shall be mitred cut and fusion welded at all corners, including drilling holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM Gasket, 1.2mm±0.2mm thick Galvanized Steel Frame of size 30mmx 18mm, 2 Nos, Sliding Sash of size 30mm x 18mm, Sliding Mesh Sash of size 26mm x 10mm profile to be inserted in required profile, frame shall be fixed to the wall with 8mm X 100mm long fasteners,Hardware such as Touch lock of zinc alloyed [white powder coated], Steel roller system, including Glazing with 5mm thick selected quality Sheet Glass and Stainless Steel Wire Cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories shall be provided with proper operative and locking hardware mechanism and Aluminium track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock. frame shall be fixed to wall with high quality fasteners and silicon glue shall be applied to fill up gap between frame and wall to make leak proof complete all as specified and as per Manufacturer instructions. Note: The unit rate quoted by contractor includes cost of Sheet Glass and Stainless Steel Wire Cloth includes all other connected accessories. Net opening will be measured for payment purpose. |
| 24 | S & F Factory made UPVC Fixed Window / Ventilator, White Colour, of area not exceeding 1.0 Sq.m each, made of extruded profiles with wall thickness of 2.3mm±0.2mm, Window profile with hollow section with multi chamber, Frame of size 60mm X 58mm, T Profile [One vertical length in between two shutters] of size 60mmx 74mm, Glazing Bead of size 35mm X 20mm will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM Gasket, 1.2mm±0.2mm thick Galvanized Steel Frame of size 28mmx 21.5mm, T Profile of size 27mm x 17mm to be inserted in required profile, frame shall be fixed to wall with 8mm X 100mm long fasteners, 5mm thick glazing with selected quality Frosted Glass / Sheet Glass complete all as specified and as per Manufacturer instructions. Note: The unit rate quoted by contractor includes cost of Frosted Glass / Sheet Glass includes all other connected accessories. Net opening will be measured for payment purpose. |
| 25 | S & F Mild Steel work conforming to Fe - 290, Grade E-165, as in framed work portions framed and hung as gates, including Pintle hinges, stops, hand-made sliding bolts, etc. such as Ornamental and Intricate Design Grills, Gratings, Ladders etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed Guard Bars, Barred Iron Doors, Ladders, framed Balusters, Walk Ways, Railings, framework of Water Tanks and similar work complete all as specified and as directed. |
| 26 | M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces of any description, not exceeding 10 cm width or girth including preparation of surfaces complete all as specified and as directed. |
| 27 | S & F in repairs Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre and Decorative type Stainless Steel Globe type Brackets of size suitable to 25mm dia curtain rod complete all as specified and as directed. |
| 28 | Demolition of Stone Slab laid, bedded and pointed in Cement Mortar of thickness not exceeding 25 mm and removing serviceable tiles to the stores andremoving rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed. |
| 29 | M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Landings of Staircase, Window Cills, Cooking Platform etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed andpointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabsincluding screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Treads of Steps, Landings of Staircase, Window Cills, Cooking Platform etc. The edges of Treads of Steps, Window Cills, Cooking Platform etc. shall be Bull Nosed / Half Rounded. The edges of the Treads and Landings shall also be provided with Three Nos of Grooves. |
| 30 | M & L for Kota Stone Slabs of 20 to 25 mm thick as in Floors, Treads of Steps, Window Cills etc. with machine cut edges, including Diagonals, Inlays, Borders, Margins in Two or more Colours / Shades, Designs / Patterns of Stone Slabs, set and bedded with Grey Cement [Slurry] and jointed and pointed with Grey Cement slurry mixed with a Admixture of Pigment to match shade of Slabs, Rubbing and Grinding with Mechanical Equipment fitted with suitable Grit Size Carborundum Stones and Polishing with Oxalic Acid to smooth, bright Mirror finish including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single Stone Slab shall be used for entire Width and Length of Steps, Window Cills, etc. The edges of Treads shall be Bull Nosed / Half Rounded. The edges of the Treads and Landings shall also be provided with Three Nos of Grooves. |
| 31 | M & L for Kota Stone Slabs of 20 to 25 mm thick as in Skirting, Dado, Risers of Steps, Jambs, Pillars etc. with machine cut edges, including Diagonals, Inlays, Borders, Margins in two or more Colours / Shades, Designs / Patterns of Stone Slabs, set and bedded with Grey Cement [Slurry] and jointed and pointed with Grey Cement slurry mixed with Admixture of Pigment to match shade of Slabs, Rubbing and Grinding with Mechanical Equipment fitted with suitable Grit size Carborundum Stones and Polishing with Oxalic Acid to smooth, bright mirror finish over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single Stone Slab shall be used for entire Height of Skirting / Dado / Risers and Joints shall match with the Flooring. |
| 32 | M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Sub base for flooring complete all as specified and as directed. |
| 33 | Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores andremoving rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed. |
| 34 | M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE. |
| 35 | M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as inSkirting and Dado etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE. |
| 36 | M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE. |
| 37 | M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE. |
| 38 | S & F in repairs 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed. |
| 39 | S & F in repairs 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed. |
| 40 | S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed. |
| 41 | S & F 75 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed. |
| 42 | S & F 75 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed. |
| 43 | S & F 110 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed. |
| 44 | S & F 75 mm bore PVC [SWR] Branch Piece, Single [Single \"Y\"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. |
| 45 | M & L for PVC [SWR] Floor Trap with 75mm dia outlet, plain with grating including jointing to waste pipe with solvent cement complete all as specified and as directed. |
| 46 | S & F in repairs Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, Short Body with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. CON-047KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 47 | S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. CON-041KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 48 | S & F in repairs Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered \"Hot\" or \"Cold\" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as per Jaquar Catalogue No. CON-011KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 49 | S & F in repairs Stop Valves, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as per Jaquar Catalogue No. CON-083KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 50 | S & F in repairs Health Faucet, Chromium Plated ABS Body with 1.20 m long flexible tube, wall hook, non return valve complete as per Jaquar Catalogue No. ALD-577 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified and as directed. |
| 51 | S & F in repairs Stainless Steel, Tubular Towel Rail, D Type, 600 mm long between flanges complete all as per Jaquar Catalogue No. ACN-1111SM or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 52 | S & F in repairs 600 mm X 450 mm Bevelled Edge Mirror of selected quality glass, 5 mm thick, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with CP brass screws and cup washers complete all as specified and as directed. |
| 53 | S & F in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. complete all as specified. |
| 54 | S & F Vitreous China Wash Down Water Closet [Pedestal pattern], White, including Plastic Water Closet Seat, Back, Closed Pattern, White with Flat Bottom and Cover and Mild Steel Chromium Plated or Aluminium Hinging Device and \"P\" or \"S\" Trap and including 10 Litres capacity, PVC Valve less, Syphonic action type, Low Level Flushing Ccistern, White, with Inlet Ball Valve, Float, Handle, Flush Pipe of Polyethylene of Low or High Density of PVC, 32mm dia, PVC Connection of 15mm Bore and 600mm Long with PTMT Check Nut and Union etc. including Brackets and Connections to Pipe and Flush Pipe mplete all as specified and as directed. |
| 55 | S & F in repairs Stainless Steel, Soap Dish, Fancy Type complete all as per Jaquar Catalogue No. ACN-1131N or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 56 | S & F in repairs Brass Chromium Plated Shower Rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed. |
| 57 | S & F in repairs Stainless Steel Kitchen Plate Rack of size 24\"x30\"x10\", made of 0.85mm thick Stainless Steel Sheet complete all as directed. [Make: Model No. P-330 of Prayag or its equivalent in Polytuf / Nirali / Jayna / Neelkant] |
| 58 | M & L for providing Precast RCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in Landings, Cover Slabs [for Manholes etc], Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and similar articles with plain faces set in Cement Mortar 1:6 complete all as specified and as directed. |
| 59 | S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. |
| 60 | Demolition of Brickwork or Stone / Boulder Masonry, built in Cement Mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed. |
| 61 | M & L for brick work in half brick thick walls using Fly Ash Blocks [Modular Bricks] straight or curved on plan to any radius built in Cement Mortar 1:4including 2 Nos of 6mm dia bars at every fourth course of brick work complete all as specified and as directed. |
| 62 | Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed. |
| 63 | M & L for Cutting / Chipping the spalling concrete surfaces of Slabs, Beams, Columns, Fins, Facias, Parapets & Chajjas etc. and trimming, cleaning the surfaces of any thickness to receive Plastering, preparing surfaces and welding steel wire Fabric / Mesh of size 75X25mm of weight not less then 3.0KG per Sq.m to existing reinforcement, and Rendering, in Cement Mortar 1:3, of required thickness, including mixing water proofing compound as per manufacturer\"s instructions and finishing the top surface even and smooth without using extra cement and finishing surface rough conforming to proper geometrics including providing double scaffolding and safety measures as required and removal of the same on completion and disposal and depositing the demolished material out of MD land complete all as specified and as directed. |
| 64 | M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 65 | M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturer\"s instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. |
| 66 | M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 67 | M & L for preparing newly plastered wall surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over One Coat of Alkali Resistant Primer on walls complete all as specified and as directed. |
| 68 | M & L for Complete removal of existing treatment of any description on walls and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Acrylic Washable Distemper over One Coat of Alkali Resistant Primer on walls complete all as specified and as directed. |
| 69 | M & L for preparing newly plastered wall surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint on walls complete all as specified and as directed. |
| 70 | M & L for Complete removal of existing treatment of any description on walls and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint on walls complete all as specified and as directed. |
| 71 | M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying two coats of white wash on ceilings complete all as specified and as directed. |
| 72 | M & L for preparing newly plastered ceiling surfaces and applying threecoats of white washing complete all as specified and as directed. |
| 73 | Taking down or up steel tubing and connections for 20 mm bore of pipe complete all as specified and as directed. |
| 74 | Taking down or up steel tubing and connections for 25 mm bore of pipe complete all as specified and as directed. |
| 75 | S & F in repairs Angle Cock, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete all as per Jaquar Catalogue No. CON-053KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified. |
| 76 | S & F in repairs, Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 20 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed. |
| 77 | S & F in repairs Stainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated,and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 355 mm x 165 mm complete all as specified and as directed. |
| 78 | S & F in repairs 18mm thick, Prelaminated MDF Board, One Side Decorative Choice Lamination and other side Balancing White, Medium Density, Exterior Grade fixed with screws to wooden frames, partitions, shelves, cupboards, door panels complete all as specified and as directed. |
| 79 | S & F Continuous [Piano] Hinges, Mild Steel, Bright finish or Electrogalvanised and width of Flaps 30mm [When Open] complete all as specified and as directed. |
| 80 | M & L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 81 | M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. |
| 82 | Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed. |
| 83 | M & L for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc. surface finished even and smooth with out using extra cement complete all as specified and as directed. |
| 84 | S & F 32mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittingscomplete to walls, ceilings or in floors etc. including testing complete all as specified and as directed. |
| 85 | S & F 25mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittingscomplete to walls, ceilings or in floors etc. including testing complete all as specified and as directed. |
| 86 | S & F 16mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittingscomplete to walls, ceilings or in floors etc. including testing complete all as specified and as directed. |
| 87 | M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed. |
| 88 | M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed. |
| 89 | M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed. |
| 90 | Dismantling of Cast Iron Work of any description complete all as specified and as directed. |
| 91 | S & F Stainless Steel Railing made with Stainless Steel Pipes of wall thickness not less than 1.6mm, of Grade AISI 304, standard quality, bright polish finish, using 50mm dia pipes for hand rail, 25mm dia pipes for vertical supports / balusters and 25mm dia pipes as in tie bars in three layers, SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed. |
| 92 | M & L for Uprooting and Removal of Wild Trees / Grass / Bushes etc. from the Manholes / Soil Pipes / Septic Tanks / Soak Wells and their surroundings including its penetrated roots and making good the damaged plaster with Cement Mortar [1:3] and finished the surfaces to match with existing surfaces complete all as specified and as directed. |
| 93 | S & F Rotational Moulded Polythene [HDPE] Water Tanks, Triple Layered, ISI Marked, Cylindrical & Vertical Type 500 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete including taking down old tanks and removing to store complete all as specified and as directed. |
| 94 | M & L for Site clearance by clearing away all Shrubs, Vegetation, Grass, Bushes, Weed, Trees and Saplings not exceeding 30 cm in girth, measured at a height of one meter above ground level, Grubbing up tree trunk by digging out roots up to 60 cm below ground level including cutting of trunk portion protruding over ground, removal of stumps, digging out roots, filling holes and levelling off ground, filled up with earth, well rammed and levelled, removing boulders if any which interfere with the work, after breaking down if necessary including stacking of serviceable material and removing of unserviceable material to a distance not exceeding 50m / outside the periphery of the area under clearance and burnt or otherwise disposed of as directed in low laying areas outside the MD Land complete all as specified and as directed. |
| 95 | M & L for Hardcore of Gauge not exceeding 63 mm of Broken Stones or Boulders, deposited, spread and levelled in layers not exceeding15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed. |
| 96 | M & L for 100 mm thick, PCC 1:3:6, Type C-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed. |
| 97 | M & L for 75 mm thick, PCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in flooring, surface finished fair and even complete all as specified and as directed. |
| 98 | M & L for Synthetic Turf Surface for Volleyball Court, 50 mm thick and Synthetic Acrylic based Volleyball Court Painting [White Colour] for standard size of Volleyball Court [9.00m X 28.00m] with the following specifications complete all as specified and as directed.[a] Material / Dtex: PE15000[b] Structure: Monofilament Yarn[c] Pile Height: 50mm[d] Stitch Rate Per 10cm: 15[e] Gauge: 5/8\"[f] Stitches / Sq.m: 9450[g] Roll Width X Length: 4 or 2 X 25 m[h] Backing: Triple Layers[i] Shall have High Wear Resistance, Perfect Ball Roll Properties & UV ResistanceMake: Zap Exports Pvt Ltd / Bellinturf Artificial Turf / Amico Sports Pvt Ltd as approved by GE |
| 99 | Supply and installation of 02 [Two] Nos of 50mm dia, Heavy Grade GI Volleyball Portable Poles having 4mm wall thickness including Wire Net tightening mechanism and including 01 [One] Heavy duty Synthetic Net made of 10 cm Square Black / White mesh with Synthetic tape all as specified and as directed.Make: Grip International / Amico Sports Pvt Ltd / Nipun Sports Private Limited. |
| 100 | M & L for PCC 1:4:8, Type D–2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed. |
| 101 | M & L for PCC 1:3:6, Type C-2 [using 40 mm graded granite stone aggregate] in surface channels and drains including forming fair finished drain or channel of any inner girth using extra cement including forms, moulds, mitred / stooped ends complete all as specified and as directed. |
| 102 | M & L for brick work with Fly Ash Blocks [Modular Bricks], straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed. |
| 103 | M & L for preparation of newly plastered Wall Surfaces and applying Two Coats of Cement Based Paint over One Coat of Alkali Resistant Primer complete all as specified and as directed. |
| 104 | M & L for preparation of new Brick, Stone, Concrete, Asbestos Cement, Plaster Surfaces or Particle Board or wood based surfaces over 10cm width or girth and applying Two Coats of synthetic enamel paint over a coat of primer complete all as specified and as directed. |
| 105 | Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good the disturbed surfaces all as per existing complete all as specified and as directed. |
| 106 | M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Pressed Metal Flush Box made out of 2mm thick MS Sheet of suitable size and 3 mm thick Hylam Sheet top cover for fixing switches, fittings, regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point controlled by One Switch complete all as specified and as directed. |
| 107 | All as per Serial Item No. 106 above but for One Light Point controlled by Two Nos. of, Two way Switches complete all as specified and as directed. |
| 108 | All as per Serial Item No. 106 above but One 3 Pin Switch Socket Outlet 5 Amps on Independent Board complete all as specified. |
| 109 | All as per Serial Item No. 106 above but for One 3 pin Socket Outlet 5 Amps on the Same Board with other switches complete all as specified and as directed. |
| 110 | All as per Serial Item No. 106 above but One 3 Pin Switch Socket Outlet 6 Amps on Independent Board but below the Switch Board of Light Points in the same Vertical Plane, complete all as specified. |
| 111 | All as per Serial Item No. 106 above but one 3 Pin Switch Socket Outlet 15 Amps on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor. |
| 112 | M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old sub main wiring of any description and making good disturbed surface complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit. Rate quoted is also deemed to be including cost of Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, Cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed. |
| 113 | S & F Switch Piano, Flush Button, Single Pole, Two Way, 6 Amps, 230 Volts complete all as specified and as directed. |
| 114 | S & F Switch Piano, Flush Button, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed. |
| 115 | S & F Socket Outlet, 3 & 2 Pin, Multipurpose, 6 Amps, 230 Volts, Flush Type complete all as specified and as directed. |
| 116 | S & F Switch Socket Outlet, 3 & 2 Pin, Multipurpose, 6 Amps, 230 Volts, Flush Type complete all as specified and as directed. |
| 117 | S & F Switch Socket Outlet, Multipurpose, 3 pin, 16 Amps and 3 pin, 6 Amps, Flush Type, 230 Volts controlled by One Switch complete all as specified and as directed. |
| 118 | S & F Ceiling Rose, Surface Bakelite, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed. |
| 119 | S & F Bell, Ding Dong / Multi Music Type, AC, 230 Volts, Single Pole complete all as specified and as directed. |
| 120 | S & F Bell Push, Flush Button, Single Pole, 6 Amps, 230 Volts complete all as specified and as directed. |
| 121 | S & F Electronic Fan Regulator, Stepped Type, Flush Type, AC, 230 Volts, Single Pole complete all as specified and as directed. |
| 122 | S & F in repairs MCB DB, TPN, 4 Way, 415 Volts, Vertical, with DIN Channel, N3 Frame, Double Door with 250 Amps rated bus bar, IP43 rated suitable for mounting MCBs complete all as specified and as directed. |
| 123 | S & F in repairs MCB DB, SPN, 8 Way, 240 Volts, Vertical, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs complete all as specified and as directed. |
| 124 | S & F MCCB, TP, 100 Amps, 36 KA, 415 Volts, 50 Hz, suitable for fixing on N3 Frame complete all as specified and as directed. |
| 125 | S & F MCB, SPN, 40 to 63 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed. |
| 126 | S & F MCB, SP, 6 to 32 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed. |
| 127 | S & F MCB, DP, 40 to 63 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed. |
| 128 | S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 1000 Lumens output, 5700K of cool white, with extruded Aluminium housing and robust construction with necessary acrylic diffuser & Integrated Electronic Driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing tube light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 |
| 129 | S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 5700K of cool white, with extruded Aluminium housing and robust construction with necessary acrylic diffuser & Integrated Electronic Driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing tube light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 |
| 130 | S & F Energy efficient Sleek LED Mirror Light Fitting of not less than 1000 Lumens, Surface / Recessmounted with Acrylic / PMMA diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 |
| 131 | S & F LED Bulkhead Fitting of not less than 1400 Lumens output with Pressure Die Cast Aluminium Housing, suitable for surface and wall mounting applications. With all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 |
| 132 | S & F Energy efficient & Long life Building Security Light Luminaire / Street Light Luminaire, of not less than 2500 Lumens output, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mmincluding taking down existing Light Fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 |
| 133 | M & L for Taking down Ceiling Fan of any description from its position and refixing the same after repairs to buildings, at same place or at new place including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm, replacement of Spares such as Capacitor 2.5 Mfd, Bearings, Shaft Bushes, Capacitor, Cotter Pin, Clamps, Rubber Bushes, Nuts & Bolts etc. as required and also including cleaning, greasing and spray painting with two coats of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and complete all as specified and directed. |
| 134 | M & L for Rewinding of Motor of Ceiling Fan of any description using super enamelled copper conductor of suitable gauge including insulation, varnishing, packing and testing etc., cleaning, greasing etc.complete all as specified and directed. |
| 135 | S & F Exhaust Fan, 300mm Sweep, 1400 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and fixing in existing opening and making good the disturbed surface to match with existing and taking down existing Exhaust Fan of any description and depositing at MES Store Yard complete all as specified and as directed. Make: Crompton Greaves / Havells / Almonard / Bajaj / Orient |
| 136 | Supplying, laying and testing XLPE insulated and PVC sheathed, FRLS, armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 3½ Core, 25 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. including taking down old LT Cables of any description complete all as specified and as directed. |
| 137 | M & L for Cutting Bituminous Road / Hardstanding etc. as required for Jointing / Laying Cables and Pipeline of width not exceeding 300mm and depth not exceeding 600mm and refilling after laying and making good with PCC 1:2:4, Type B1 using 20mm graded stone aggregate, 100mm thick complete all as specified and as directed. |
| 138 | Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and depth not exceeding 1.5m and getting out in Soft / Loose soil complete all as specified and as directed. |
| 139 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. |
| 140 | Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. |
| 141 | M & L for Dry River Sand cushioning over and around the cable for cable protection in trenches, levelled and punned down complete all as specified and as directed. Note: The punned down thickness shall be measured for payment. |
| 142 | M & L for Earthing complete with CI Earth Pipe Electrode with Flanged ends, Centrifugally Cast, Class \"A\"\", Heavy Duty, 80 mm dia all as per IS – 1536 of 2.50m length burried directly and preferably vertically in ground with top edge of the Pipe not less than 2.00 metres below Natural Ground Level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Pipe Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, Drilling 400mm dia Bore Hole in any type of strata by suitable means for lowering the CI Pipe, removal of surplus soil etc. and disconnecting and taking down existing Earthing of any description complete all as specified and as directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
