|
| 1 | Takingdown chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed. |
| 2 | Taking down chowkhat with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each complete all as specified and directed. |
| 3 | Taking down shutters of any descriptionexc 1 Sqm and n.exc 2 Sqm each eachcomplete all as specified and directed. |
| 4 | S&F Second class hard wood Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed. |
| 5 | S&F for Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube,suppling and fixing in opening as per specification & drawing |
| 6 | S&F Fatory made solid panel PVC door shutter, 30mm thick(stiles), consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain cover PVC \"C\" channel having a PVC sheet strip of 20mm width struk inside with solvent cement for stiles and plain colour PVC sheet for top rail,lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at siteas per specification & drawing |
| 7 | S&F Factory made solid PVC moulded door shutter 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face, suppling & fixing in the frame including butt hinges-03 Nos, Aluminium 02 Handles (100mm), and Aluminium tower bolt-150mm at site as per specification complete all as specified and directed by Engineer-in-Charge. |
| 8 | S&F 35mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides fixed to chowkhats complete all as specified and directed. |
| 9 | S&F 35 mm thick plain, framed, panelled shutters(any number of panels) factory made, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: all as specified and directed. |
| 10 | S&F 35mm thick factory made 2nd class HW glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc size of members as specified in SSR part-I, section 8, clause 8.24(a) supplied and fixed to chowkats, including M&L for providing members of 2nd class HWwooden stiffeners of size 60x30mm horizontally and vertically to each top panel and vertically to each bottom panel of wire gauge shutter complete all as specified and directed |
| 11 | S&F galvanised mild steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks for wooden doors with nut and bolts suitable for MS beading for steel windows complete all as directed. |
| 12 | S&F 100 mm longmedium weight, stainless steel Butt hinges. |
| 13 | S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm |
| 14 | S&F aluminum anodized barrel tower bolt of extruded section size of bolt 200mm |
| 15 | S&F aluminum anodized handle fabricated type type200 mm size complete all as specified and directed. |
| 16 | S&F mild steel 250 mm long sliding door bolt type, stove encmelled black, with brigth bolt not less 16 mm dia with and including a minimum of 6 bolts and nuts etc complete. |
| 17 | Supply and fixing floor door stopper 100 mm size of aluminium alloy body and anodized. |
| 18 | S&FProviding and fixing factory made uPVC white colour casement window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm) . T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware andrainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fastenersand 5mm thick plain sheet glass of selected quality. Area of each window not exceeding 1.00 sqm each including taking down old fixed windows complete all as specified. |
| 19 | Supply & fixing of UPVC windows three track sliding window with two glazed and one wire mesh sliding shutters of profile width of frame 50 mm to 60 mm, limit thermal conductivity to l.3 Kcal/sqm/hr centigrade, sound insulation up to 4-0 bds, Density, 1.46 gm/ml, Tenstile strength - 43.9N/sqmm, % Elongation at break - 215, Tenstile mpduls - 2840N/Sqmm, Flexural strength - 51N/sqmm, Heat aging at 150 degrees - No surface defect, Thickness - 2 mm, Flexural moduls elasticity2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, anti lift device on slide windows with temper proof screws with and including glazed shutter fixed with 5 mm thick plain sheet glass & wire mesh shutter with stain less steel wire cloth 304 grade stainlesssteel with 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature and filling gap of wall and frame with silicon sealent completeincl taking down old down old window complete all as specified. all as directed . |
| 20 | Supply & fixing of UPVC ventilators with top hung glazed and wire mesh shutters made out ofprofile width of frame 50 mm to 60 mm, limit thermal conductivity to l.3 Kcal/sqm/hr centigrade, sound insulation up to 4-0 bds, Density, 1.46 gm/ml, Tenstile strength - 43.9N/sqmm, % Elongation at break - 215, Tenstile mpduls - 2840N/Sqmm, Flexural strength - 51N/sqmm, Heat aging at 150 degrees - No surface defect, Thickness - 2 mm, Flexural moduls elasticity2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, withpeg stay of suitable size to keep hung shutter in open position, with temper proof screws with and including glazed shutter fixed with 3 mm thick frosted glass & wire mesh shutter with stain less steel wire cloth 304 grade stainlesssteel with 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature and filling gap of wall and frame with silicon sealent completeincl taking down old down old ventilator complete all as specified all as directed. |
| 21 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 incl dismantling old mild steel work of any description complete all as specified. |
| 22 | M&L for preparation of new wood surface of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enemal paint over a coat of pink primer complete all as specified and directed |
| 23 | M&L for providing cement concrete 1:2:4 , type B1, using 20mm graded stone aggregate as in hodfasts, copings and the like complete all as specified. |
| 24 | S&F in repair 1mm thick mild steel, plain black sheet in in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required |
| 25 | Taking down cement plaster of any description built in cement mortor and removing debris outside MOD land complete all as specified |
| 26 | Demolition of brick work or stone/boulder masonary built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and rubbish off the premises. |
| 27 | M&L brick workusingsub class \"B\" old size bricks straight or curved on plan exc 6 meanradius built in CM 1:6 complete all as spfd and directed |
| 28 | M&L Brick Workusing sub class \"\"B” Bricks, straight or curved on plan exceeding 6M mean radius in half brick thick wall bulit in CM (1:4) complete all as directed by Engr-in-charge. |
| 29 | M&L for rendering 15mm thick in cment mortor 1:6 on fair faces of brick work finished even and smooth w/o using extra cement complete all as specified. |
| 30 | M&L for Preparation of new plastered surfaces and applying two coats of weather proof antifungal Acrylic Exterior emulsion paint of Apex Ultima and shade over a coat of approved primer as recommended by the manufacturer over a coat of putty to make surfaces smooth all as required and as directed. |
| 31 | M&L for Preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls over a coat of wall putty to make surfaces smooth. |
| 32 | Dismantling floor, hearth or wall tiling including cement mortar bedding removing rubbish off the premises. all as directed. |
| 33 | M&L for glazed coloured ceramic tiles in vertical surfaces 300x200x6-7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM 1:4 on other then fair faces of brick work etc complete. |
| 34 | M&L for non skid coloured ceramictiles 7-8mm thick (square or rectingular)area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 etc complete. |
| 35 | M L for preparation of new steel surface of any description over 10 cm in width or girth not other wise described and applying two coat of synthetic enemal paint over one coat of red oxide primer all as specified and directed |
| 36 | M&L for providing and fixing false ceiling with light weight 19mm thick mineral Armstrong tiles of size 595x595mm of model prima fine fissured RH 99 suspended on silhouette profile suspension system of grid made from hot dipped GI steel section notary stitched double webbed power coated white consisting of main T- runner 42mmx14mm and 0.30mm thick and cross T of size 33mmx 14mm and 0.30mm thick placed at 60cm centre having width of flange 14mm with a 6mm reveal profile (Blace).The grid system to be rested on the periphery wall/partitions on a W-profile wall section made of pre-coated galvanized steel of dimension 3.0mm long x (15mm+10mm) x22.5mm and laying false ceiling for services like diffusers grill including cutting, makingopening for services like diffusers grill light fitting, fixture smoke detectors etc. Wherever required main T-runner to be suspended from ceiling using GI suffix cleats of size 25mm x 35mm x 1.6mm fixed to ceiling with 6mm dia and 50mm long dash fastener, 4mm dia GI adjustable rods with galvanized level adjustment clips spaced as required, all complete at all height as per specification, drawing and incl dismantling old false ceiling all as per direction of Engr in Charge. |
| 37 | Taking down existing venetian blinds Rolling type completely with fittings of any type and supply and fix new venetian blinds Rolling type of approved, fabric blinds including all necessary fittings of approved colour to match with the existing, complete all as specified and as directed. |
| 38 | Hacking out broken glass from aluminium frame and S & F sheet glass, 4.8mm thick, ordinary quality area exc. 0.50 Sqm in each pane fixed with rubber beading, complete all as directed. |
| 39 | Hacking out old broken glass (any thickness, size, quality) from woodenframes and supply and fixing sheet glass 4mm thick, ordinary quality area n exc.0.50 Sqm in each pane, glazing with putty/ wooden beads, complete all as directed. |
| 40 | Hacking out the old broken glass (any thickness, size) from steel frame glazed with oil putty or fixed with beads and supply and fix pin headed glass of 4mm thick fixed with oil putty and clips in squares not exceeding 0.50 Sqm in each, complete all as directed. |
| 41 | All as per srl item No.40 here-in-before but 3.0mm thick. |
| 42 | S&F Solar control film 25 micron, reflective type of approved shade stuck to glass panes of Aluminium windows, doors etc., complete all as directed. |
| 43 | All as per Sl item No.42 here-in-before but as in repairs including removing existing unserviceable/damaged film and clearing the glass to receive new film, complete all as directed. |
| 44 | M&L for Powder coated aluminum frame of any typefor doors, windows,ventilators, partitions with one or more rebates including joining cleat etc fixed to frame with aluminium screws complete all as specified. |
| 45 | S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.including taking down old existing aluminium window shutters complete all as specified and as directed. |
| 46 | S&F Anodised aluminium powder coated window shutters side (thickness of powder coating not less than 50 mircon) side hung/sliding, without sash bars aluminium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips, neoprene rubber packing, handles-01No in each shutter, hinges 2 Nos/ rollers, snap beading, including taking down old existing aluminium window shutters complete all as specified and as directed. |
| 47 | S&F in repairs, Aluminium anodised or powder coated grill (thickness of powder coating not less than 50 mircon), weight not less than 2.0Kg/ sqm fixed to aluminium windows, complete all as specified and as directed. |
| 48 | S&F Pre-laminated particle board 18/19mm thick, interior grade, pre laminatedone side decorative choice lamination and side balancing white,fixed in frame, complete all as specified and as directed byEngineer –In -Charge. |
| 49 | S&F Pre-laminated particle board 12mm thick, interior grade, pre laminatedboth side decorative ,fixed in panels to aluminum frame including powder coated snap beading complete all as specified and as directed byEngineer –In -Charge. |
| 50 | M&L double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including taking out the old damaged spring of any description and in any position and making good all disturbed surfaces to match with adjoining surface, complete all as directed. |
| 51 | S&F in repair Aluminium extruded section body hydraulic door closer hydraulically regulated designed No.3 universal type suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as directed. |
| 52 | S&F in repair Harrison rails, mild steel, chromium platedwith fixing brackets,stops,rollers etc. Stainless steel curtain rods of 25mm diaincluding taking down the existing. |
| 53 | S & F in repairs PVC (SWR) pipes 110mm bore, single socketed in any length with rubber ring joints fixed to wall or laid in floorscomplete all as directed by Engineer -in-Charge. |
| 54 | S & F in repairs PVC (SWR) bends (any radius) suitable for 110 mm bore pipe complete all as directed by Engineer -in-Charge. |
