|
| 1 | Arch SwingSUPPLY AND FIXING OF ARCH SWING. LEG SUPPORT: 80 MM NB PIPE, SEAT- ANTI SKID RUBBER BELT. BEARING : HEAVY DUTY BALL BEARING. AREA : 3.0 M X 2.5 M. HEIGHT : 2.5 M. TOP BAR : 60 MM NB PIPE. SUSPENSION : 6 MM RUBBER COATED CHAIN. THE TOPCOAT IS DULY POWDER COATED. IN THIS ONE CHILD CAN ENJOY THE SWING AT ONE TIME. THE ARCH SHAPED SIDE FRAME SHALL BE MADE OF 80MM NB B CLASS GI PIPE SHALL BE MADE UP OF 50MM NB B CLASS GI PIPE. THE FRAME SHALL BE POWDER COATED TO GIVE AN AESTHETIC LOOK. THE SWING SHALL BE MADE UP OF 10MM THICK ANTI SKID RUBBER TOP THE RUBBER BELT SEAT / U SHAPE SWING SEAT WITH 2 EYE BOLT TYB-S06. MADE OF POLYURETHANE OF SIZE：53 X 20.5 X 20 SHALL BE SUSPENDED ON 6MM RUBBER COATED GI CHAIRN. THE BAIL BEARINGS SHALL BE MOUNTED INSIDE A SPECIALLY DESIGNED NYLON CLAMP. COATING WITH PURE POLYMER POWDER WITH 7 TANK TREATMENT 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OFEQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) (AS PER DIRECTION OF OFFICER IN CHARGE.) |
| 2 | Std. See SawSUPPLY AND FIXING OF STD. SEE SAWHANDLE :-20 MM N B PIPE. LEVER-32 MM N B PIPE. COLMUN : 60 MM N B PIPE. BEARING : NYLON BUSH PRESS FITTED. SEATS: FRP SEATS WITH STEEL FRAME. THE TOPCOAT IS DULY POWDER COATED. THE LEVEL OF SEE SAW SHALL BE MADE FROM 15, 20 AND 25MM NB B CLASS GI PIPE. THE SEAT OF SEE SAW SHALL BE MADE FROM FRP/LLDPE. THE STAND AND BUSH BEARING MADE IN 40MM NB B CLASS GI PIPE. SEE SAW LEVER SHALL BE WELDED TO 5MM THICKNESS MS PLATE FOR NUT BOLTING WITH STAND. ALL PIPES FLAT SHALL BE POWDER COATED TO AVOID RUSTING. COATING WITH PURE POLYMER POWDER WITH 7 TANK TREATMENT 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OFEQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)C37C40C41C39 (AS PER DIRECTION OF OFFICER IN CHARGE.) |
| 3 | FOUR SEATED MERRY GO ROUNDSUPPLY AND FIXING OF FOUR SEATED MERRY GO ROUND.AREA: 1.5 M. HEIGHT – 0.8 M. SEAT – MOULDED F.R.P. MAIN FRAME: 40 NB G.I. PIPE. BEARING : HEAVY DUTY BEARING. MS PLATE: 250X10MM. SUPPORT PIPE- 80NB. THE TOPCOAT IS DULY POWDER COATED.THE ITEM SHALL BE HAVING ITS MAIN FRAME MADE UP OF 25 & 40. MM NB “B” CLASS G.I. PIPE. THE STAND SHALL BE MADE IN 80 MM NB “B” CLASS G.I. PIPE. THE WHOLE STRUCTURE SHALL BE MOUNTED ON HEAVY DUTY BEARING SHAFT. THE BEARING USED SHALL BE OF HEAVY DUTY BEARING PERMANENTLY LUBRICATED WITH WATER SEALANT. THE SEAT FRAME SHALL BE MADE OUT OF FRP (FIBRE REINFORCED PLASTIC)/LLDPE (LOW LINEAR DENSITY PLOY ETHYLENE). THE SEATS SHALL HAVE HANDRAILS SO THAT THE CHILD DOES NOT FALL. IT SHALL ACCOMMODATE 4 CHILDREN AT A TIME. THE POWDER COATING SHALL BE DONE ON THE PIPES TO AVOID RUSTING. COATING WITH PURE POLYMER POWDER WITH 7 TANK TREATMENT 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OFEQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) (AS PER DIRECTION OF OFFICER IN CHARGE.) |
| 4 | WAVE SLIDESUPPLY AND FIXING OF WAVE SLIDE.LADDER-FRAME- 25M M N B PIPE. HANDRAIL - 20 MM N B PIPE. CENTRE SUPPORT- 50 MMN B PIPE. AREA : 0.5 M X3.5 M. PLATFORM HEIGHT : 2.1 M. CHUTEFRP.THE TOPCOAT IS DONE USING THE BEST QUALITY BRAND OR DULY POWDER COATED. THE WAVE SLIDECHUTE SHALL BE MADE UP OF 4MM THICK FRP / LLDPE MATERIALS. THE STRUCTURE SHALL COMPRISE OF 20 AND 25 MM NB BCLASS GI PIPES. THE CENTER SUPPORT SHALL BE MADE IN 90MM NB B CLASS GI PIPE. THE LADDER CUM RAILING SHALL BE MADE 20MM AND 25MM NB B CLASS GI PIPES. THE PLATFORM SHALL BE MADE UP OF 14 SWG GI SHEET WITH ANTI SKID FOR FIRM FOOT GRIP. THERE SHALL BE TRIANGULAR STEPS 16 SWG GI SHEET. THE CHUTE SHALL HAVE ITS END SUCH AS IT CAUSES SAFE LANDING OF THE CHILD. THE PIPES SHALL BE POWDER COATED COATING WITH PURE POLYMER POWDER WITH 7 TANK TREATMENT 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OFEQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) (AS PER DIRECTION OF OFFICER IN CHARGE.) |
| 5 | DOUBLE PULL- DOWNTRICEPS PULLERTRICEPS PULLER(DIMEMSIONS:- 2110MM (LENGTH) X 600MM (WIDTH) X 1600MM (HEIGHT) TRICEPS PULLER IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NBMADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 32MM NB & 25MM NB “C” CLASS GI-PIPE. THE SEAT FRAME IS OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUNDPLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM & 17MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205 & 6203” PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL. THE CIRCLIP USED FOR ASSEMBLY IS MADE UP OF 25MM & 17MM DIA.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 6 | LEG PRESSLEG PRESS IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 25MM NB “C” CLASS GI-PIPE. MIDDLE SUPPORT IS OF 25MM NB “C” CLASS GI-PIPE. LOWER FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE.FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUNDPLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM DIA SOLID BAR. THE BEARINGSUSED ARE OF “6205 PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CIRCLIPS USED FOR ASSEMBLY ARE MADE UP OF 25MM DIA. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 7 | BACK EXTENSION DIMENSIONS: - 1400MM (LENGTH) X 700MM (WIDTH) X820MM (HEIGHT). SAFE AREA: - 2.4MTR X 1.7MTR. BACK EXTENSIONEQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB PIPE. (NBSTANDS FOR NOMINAL BORE I.E. INTERNAL DIAMETER OF PIPE IN MM) THEMAIN FRAME IS OF 50MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOOTRESTING FRAME OF 32MM NB MADE FROM ”C” CLASS G.I. PIPE. THEHANDLE FRAME IS OF 25NB MADE FROM “C” CLASS G.I. PIPE. THE SEATFITTED ON THE OUTER FRAMES IS MADE UP OF M.S. SHEET OF SIZE 330MM X 300MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLSAND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES.THE FOUNDATION USED FOR FIXING IS CONSISTS OF 50MM NB MADEFROM ”C” CLASS G.I. PIPE.THE FOOTRESTS ARE MADE FROM INJECTIONMOULDED PLASTIC LLDPE / HDPE. THE GYM EQUIPMENT SHALL BEFINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRONFOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTERPOWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USINGEXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THEHOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED INCEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4STONE AGG. 20MM NOMINAL SIZE). |
| 8 | DOUBLE TWISTER(DIMENSIONS: - 1700MM (LENGTH) X 540MM (WIDTH) X 1250MM. (HEIGHT). SAFE AREA: - 3 MTR X 1MTR.DOUBLE TWISTER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENTNB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETRES. THE CENTER PIPE IS OF 100MM NB MADE FROM“C” CLASS G.I. ROUND PIPE. THE M.S. ROUND PLATE OF DIA250 MM & 10MM THICKNESS IS WELDED AT BOTTOM.THE STANDING FRAME OF THE DOUBLE TWISTER IS OF 32 NB MADE FROM“C”CLASS G.I. PIPE. THE HANDLE FRAME OF DOUBLE TWISTER IS 25 NB. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS, WELDED WITH M.S. ROUND PLATE OF DIA250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE TWISTER PLATE FITTED ON THE STANDING FRAME IS MADE UP OF M.S. ROUND PLATE OF SIZE 300MM DIAMETER AND 10MM THICKNESS. CLOSING CAPS MADE FROM TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WHICH IS OF 2 MM THICK.THE PINS USED ARE MADE UP OF DIA 25 MM MS BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205ZZ” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 9 | SKY WALKER / DOUBLE CROSS WALKERSKY WALKER DIMENSIONS: - 1720MM (LENGTH) X 630MM (WIDTH) X 1750MM.(HEIGHT).SAFE AREA: - 2.7MTR X 1.6MTR. SKY WALKER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME PIPE IS OF 80MM NB MADE FROM “C” CLASS G.I. MATERIAL WHICH IS BEND AT THE RADIUS OF 250MM.THE LEG MOVEMENT FRAME IS OF 50 X 50MM X 3MM THICK CRC SQUARE PIPE. SLEEVES ARE MADE UP OF 100 MM OD M.S. PIPE WITH THICKNESS 5MM. THIS RESULTS IN EASY REPLACEMENT OF BEARINGS, PINS AND HANDLE THE HANDLE FRAME IS OF 25MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. TWO FOUNDATIONS ARE PROVIDED FOR RIGID SUPPORT. THE FOOTRESTS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. THE PINS USED ARE MADE UP OF DIA 25MM SAE8620 BRIGHT MATERIAL. PINS ARE FIXED AT THE OUTER END WITH M8 GRUB SCREWS AND DIA.8MM SS BALL. THE BEARINGS USED ARE “62052RS1” ARE PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CERCLIPS USED FOR ASSEMBLY ARE OF A24 TYPE. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 10 | CHEST PRESS . DIMENSIONS: - 2000MM (LENGTH) X 710MM (WIDTH) X 2200MM. (HEIGHT). SAFE AREA: - 3.0MTR X 1.7MTR. CHEST PRESS EQUIPMENT MADE UP OF “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE UP OF “C” CLASS G.I. PIPE. THE BOTTOM WELDED WITH SUPPORT OF M.S. ROUND PLATE OF DIA250 MM & 10MM THICKNESS. THE CONNECTING PIPES ARE MADE UP FROM 25NB “C” CLASS G.I. PIPE. THE HANDLE FRAME IS MADE UP FROM 32NB “C” CLASS G.I. PIPE. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM MS SEAMLESS PIPE OF 60MM O.D. AND 5MM THICKNESS AS WELL AS 60MM DIAMETER SOLID BAR BUSH IS USED. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. FOUNDATION COVER CLOSING CAP IS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. PINS USED OF DIAMETER 25MM AND 17MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. BOLT M8X16 MM AND NYLOCK NUT OF M8 MADE OF SS 304 USED ON NYLON CAP MOUNTED ON PINS TO PROTECT BEARINGS AND PINS FROM RAIN AND DUST. THE BEARINGS USED ARE OF “62052RS1” &“62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTEDBRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CER CLIPS USED FOR LOCKING IS MADE UP OF A24 MM & A16MM. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). |
| 11 | SHOULDER BUILDER PROVIDING AND FIXING SHOULDER BUILDER MADE FROM C- CLASS GI PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI PIPE, AND THE BOTTOM SUPPORT OF M.S.ROUND PLATE OF 250 MM DIAMETER & 10MM THICKNESS IS WELDED AT BOTTOM. THE HANDLE MOVEMENT FRAME IS OF 25 NB & 20 NB MADE FROM “C” CLASS GI PIPE. TO JOIN THE CENTRE PIPE & HANDLE MOVEMENT FRAME SEAMLESS PIPE OF 130MM DIA& 3MM THICKNESS IS USED. THE FOUNDATION USED FOR FIXING CONSISTS OF THREE EQUAL ITEMS I.E. 100MM NB MADE FROM “C” CLASSGI PIPE, M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS & 25 MM X 25MM X 3MM M.S. ANGLE. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WHICH IS OF 2 MM THICKNESS. THE PINS USED ARE MADE UP OF 25 MM DIA BRIGHT BAR. THE BEARING USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SERCLIPS USED FOR ASSEMBLY IS OF 25 MM DIAMETER. THE POLY URETHIN PLASTIC BUSH IS USED FOR HANDLING. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE) |
| 12 | SUPPLY OF SIGN BOARDS OF 0.91 X 0.61M SIZE WITH SUPPORT LENGTH OF 3000 MM. MANUFACTURING, SUPPLYING AND FIXING OF RETRO REFLECTIVE SIGN BOARDS MADE OF 2 MM THICK ALUMINUM SHEET FACE TO BE FULLY COVERED WITH HIGH INTENSITY ENCAPSULATED TYPE HEAT ACTIVATED RETRO REFLECTIVE SHEETING CONFORMING TO TYPE – IV OF ASTM-D 4956-01 IN GREEN AND SILVER WHITE INCLUDING SUBJECT MATTER, MESSAGE (BILINGUAL(, SYMBOL AND BORDERS ETC AS PER IRC: 67-2001, PASTED ON SUBSTRATE BY AN ADHESIVE BACKING WHICH SHALL BE ACTIVATED BY APPLYING HEAT AND PRESSURE CONFORMING TO CLASS -2 OF ASTM-D-4956-01 AND FIXING THE SAME WITH SUITABLE SIZED ALUMINUM ALLOY RIVETS @ 20 CM C/C TO BACK SUPPORT FRAME OF M.S ANGLE IRON OF SIZE 35X35X5 MM AND M.S FLAT OF 25X5 MM ALONG WITH THEFT RESISTANT MEASURES, MOUNTED AND FIXED WITH 2 NOS. CLAMP OF MLS FLATS OF SIZE 25X5 MM TO A VERTICAL POST OF 3 MTR HEIGHT MADE UP OF MSL PIPE OF 60 MM N.B WELDED WITH TWO HOLD FAST OF M.S ANGLE 25X25X3MM OF 30CM LENGTH EACH AT BOTTOM AND INCLUDING MAKING HOLES IN PIPES, ANGLES, PROVIDING & FIXING M.S MESSAGE PLATE OF REQUIRED SIZE, STEEL WORK TO BE PAIRED WITH TWO OR MORE COATS OF SYNTHETIC ENAMEL PAINT OF REQUIRED SHADE AND OF APPROVED BRAND AND MANUFACTURE OVER A PRIMING COAT OF ZINC CHROMATE YELLOW PRIMER (VERTICAL POST TO BE PAINTED IN BLACK/WHITE/GREY COLOR) BACKSIDE OF ALUMINUM SHEET TO BE PAINTED WITH TWO OR MORE COATS OF EPOXY PAINT OVER AN APPROPRIATE PRIMING COAST INCLUDING ALL LEADS AND LIFTS ETC. COMPLETE AS PER DRAWING, SPECIFICATION AND DIRECTION OF OFFICER-IN CHARGE. |
| 13 | Repairing the gazebo roof using Dyna Roof roofing sheets, securely fixed with fasteners. The sheets are properly molded and finished to ensure durability and a clean appearance. • Material: PPGI (Pre‑painted Galvanized Iron) with aluminized coating• Thickness: Available in various thicknesses, 0.45mm• Patterns: Trapezoidal and corrugated as per direction of officer incharge• Colors:Silver, Green and Pepsi Blue as per direction of officer incharge• Durability: Resistant to corrosion, high winds, and extreme weather conditions • TBS (Trussless) Sheets: Self-supporting, machine curved sheets suitable for garden hut • Purlin Recommendations: For optimal performance, Dyna Roof painting purlins with Red Oxide Primer and then a double coat of plastic enamel paint as per direction of officer incharge.Series: DynaSilver — offers superior longevity and heat management |
| 14 | Supply and installation of floor tiles in the garden hut, including the removal of the existing flooring.Type: Non-slip (anti-skid) floor tilesMaterial: Vitrified Tiles Size: [Specify e.g., 300x300 mm, 600x600 mm]Thickness: Minimum 8 mm or as per manufacturer’s recommendationSurface Finish: Matt, textured, or structured finish to ensure slip resistanceSlip Resistance: Minimum R11 rating (DIN 51130) or COF ≥ 0.6 (ASTM C1028)Color/Design: As approved by Officer in ChargeCementitious or epoxy grout, stain-resistant, suitable for non-slip surfaces Tiles shall be laid using the thin-bed method with notched trowel Maintain uniform joint spacing (2–5 mm or as specified) Tiles must be set within the open time of the adhesive Use spacers for maintaining grout joint uniformity Ensure tile surface is flat, with lippage <1 mm Use wet tile cutter or angle grinder with appropriate blade Cut tiles neatly and finish edges smooth Grout joints after 24 hours of tile fixing Apply grout evenly and clean excess promptly For wet areas, use water-resistant or epoxy grout Clean surface of all adhesive and grout residue Polish with a soft cloth or non-abrasive cleaner Ensure slip resistance remains unaffected post-cleaningTile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, ncluding pointing in white cement mixed with pigment of matching shade complete. |
