|
| 1 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed . |
| 2 | Point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multistranded copper conductor 1.5 sq mm nominal cross-sectional area , single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and inciuding medium grade, PVC casing caping/conduit and accessories on wall/roof/floor etc, ISI marked with mild steel/pressed steel sunken box of 1.8 mm thick and 60 mm deep (with earth dolly) duly painted with two coats of anti corrosive paint/aiuminium paint over a coat of red oxide primer internally. and two coats of black bituminous paint over a coat of red oxide primer externally,covered with 3 mm thick plastic laminated sheet cover for fixing of switches, socket and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly for One light or fan point, controlled by one, one way switch 5 Amps. one light / fan point controlled by one switch complete all as specified and directed . |
| 3 | All as per item No 02 here in before but one 3 pin 5 amps switch socket on same board |
| 4 | All as per item No 02 here in before but one 3 pin 5 amps switch socket on independent board |
| 5 | All as per item No 02 here in before but with cable size 4.0 Sqmm and 4.0 Sqmm as earthwire for 3/5 pin, 15/16 amps socket outlet independent board |
| 6 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting notexc 10 cm girth complete all as specified and as directed . |
| 7 | S & F modular switch, 1 way, 6A, 1 module complete all as specified and as directed . |
| 8 | S&F modular socket, 6A, 2/3 pin combined 2 module complete all as specified and as directed . |
| 9 | S & F modular switch, 1 way, 16A, 1 modulecomplete all as specified and as directed . |
| 10 | S&F modular socket, 6/16A, 2/3 pin combined 2 module complete all as specified and as directed . |
| 11 | S&F in replacement of switch piano flush type single pole one way 5 amps 230 volts ISI marked complete all as specified and as directed . |
| 12 | S&F in replacement ofswitch socket combination flush type universal2 in 1, 3 pin 5Amps 230 volts ISI marked complete all as specified and as directed . |
| 13 | All as per Item No 12 here in above but of capacity 15 Amps. |
| 14 | S&F in replacement ofceiling rose 3 terminal 5 Amps 230 volts ISI marked, PVC/Polycarbonate, insulated body complete all as specified and as directed . |
| 15 | S & F in replacement of Fan step Regulator, 120 Watt, 2 module, hum free complete all as specified and as directed . |
| 16 | S&Fin replacement of Modular Bell push, 6 A, 1 module complete all as specified and as directed . |
| 17 | S&Fin replacement of Bell electric ding dongAC 230 Vsingle pole complete all as specified and as directed . |
| 18 | S&Fin replacement ofbatten type LED lightfitting 1x 20W, 220V, 4 feet, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed . |
| 19 | S&Fin replacement of batten type LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED tube light including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed . |
| 20 | S&F in replacement ofLED bulb 10w retrofit type to fit in lamp holder/bulk head fittings complete all as specified and as directed . |
| 21 | S&F in replacement of recess mounted/surface mounted/POP mounted or as per site requirement 2\" x 2\" square LED panel 36 watts, worm white/ Neutral white or 3000 K to 6500 K as per user requirementof size 600 x 600 x 9 mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed . |
| 22 | S&F in replacement ofround / square shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed . |
| 23 | S&F in replacement ofstreet light brackets made out of 40mm bore GI tubing, light grade, 1.5m long, bent to required shape, including necessary bending, welding, etc fixed with 2Nos. clamps made out of 32x5mm GI stripincluding necessary drilling holes, screws, nuts, bolts, etc complete all as specified and as directed |
| 24 | S&F in replacement ofLED bldg security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed |
| 25 | S & F in replacement ofSingle pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp, 240 V MCB complete all as specified and as directed. |
| 26 | S& F in replacement ofMCB SP 05 amps to 32 amps, 240 volts,10 KA complete all as specified and as directed. |
| 27 | S& F in replacement ofMCB SPN 16 amps to 32 amps, 240 volts,10 KA complete all as specified and as directed. |
| 28 | S&F in replacement of MCB TPN/FP 16 Amp to 32 Amp 415 V, 50 Hz,complete all as specified and as directed. |
| 29 | S&F in replacement ofMCB TPN/FP 40 Amp to 60 Amp 415 V, 50 Hz,complete all as specified and as directed. |
| 30 | S&F in replacement of single door MCB DB TPN 4 Way 415 V , 50 Hz,complete all as specified and as directed. |
| 31 | S&F in replacement of single door MCB DB SPN 4 Way 240 V , 50 Hz with 200A rated copper busbar complete all as specified and as directed. |
| 32 | S&F in replacement of single door MCB DB SPN 8 Way 240 V , 50 Hz,with 200A rated copper busbar complete all as specified and as directed. |
| 33 | S & F in replacement of Distribution board VTPN 4 way Vertical type double door 415 Volts as per IP-43 with provision for MCCB upto 160 Amps as incomer and SP/SPN/TPN MCB as outgoing and electrically connected up complete all as specified and as directed. |
| 34 | S&F in replacement of condenser of 2.5 MFD complete all as specified and as directed. |
| 35 | S&F in replacement of condenser of 1.5 MFD complete all as specified and as directed. |
| 36 | S&F in replacement of Rubber reel insulator, 3 Nos nut bolt , washer and lock pincomplete all as specified and as directed. |
| 37 | S&F in replacement of ceiling fan blade of 1200/1400mm sweep complete all as specified and as directed. |
| 38 | S&F in replacement of exhaust fan blade size up to 450 mm sweep complete all as specified and as directed. |
| 39 | S&F in replacement of ceiling fan downrod suitable size with GI Hook as per requirement of site of any size complete all as specified and as directed. |
| 40 | Taking down ceiling fan / exhaust fan/ wall mounting fan of any sweep sealing cable ends dismanting blade and removing fan and blade to store complete all as specified and as directed. |
| 41 | Hanging only ceiling fan and connecting up including provn of cable from ceiling rose or connector to fancomplete all as specified and as directed. |
| 42 | Fixing only exhaust fan/wall mounting and connecting up including provn of cable from ceiling rose or connector to fancomplete all as specified and as directed. |
| 43 | S&F in replacement of ball bearing suitable for ceiling fan 1200/1400mm sweep complete all as specified and as directed. |
| 44 | S&F in replacement of ball bearing suitable for exhaust fans up to 450mm sweep complete all as specified and as directed. |
| 45 | S&F in replacement of brass GM bush suitable for fan any size complete all as specified and as directed. |
| 46 | M&L rewinding of ceiling fan 1200/1400 mm sweep size with supper enameled copper wire of existing gauge including varnishing and drying including reassembling testing complete all as specified and as directed. |
| 47 | M&L rewinding of exhaust fan 250/300/380 mm sweep size with supper enameled copper wire of existing gauge including varnishing and drying including reassembling testing complete all as specified and as directed. |
| 48 | M&L painting of ceiling fan / exhaust fan complete in situ with one coat of synthetic enamel paint by spraying including filling cavity with filler after cleaning all dust etccomplete all as specified and as directed. |
| 49 | Taking downstorage type water heater from wall by disconnecting the electric connection and water inlet / outlet connection from mainof capacity up to 25 ltrs of any type and make complete all as specified and as directed. |
| 50 | Refixing storage type water heater of capacity up to 25 ltrs of any type including checking the serviceablity of all parts of such as inner vessel, rubber gasket, non return valve, heating element, thermostat etc and re assembling the same after replacing of unserviceable parts including testing complete all as specified and as directed Note :- Supply only spare parts against unserviceable parts will be measured and paid separately under relavent items . |
| 51 | Supply only heating element 1.5 KW( ISI mark)230 volts |
| 52 | Supply only thermostat immersion point type 15 Amps, 230 volts/AC |
| 53 | S&F in replacement of PVC connection pipeduly (copper) chromium plated 8 mm dia both end threaded including brass coupling bolt cone washer complete, length of pipe is not less than 450 mm suitable for Hot/ cold water system complete all as specified and directed . |
| 54 | S&F in replacement of 3 core PVC insulated and sheathed cable with copper conductor of size 40/0.076 complete all as specified and directed . |
| 55 | M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 4.0 sq mm (FRLS) in and including PVC casing & capping non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 4.0 Sq mm (FRLS) of continuous earth wire green in colour including taking down old sub main wiring complete all as specified and directed .NOTE: Three runs of 4.0 sqmm cable and one run of PVC casing & capping shall be paid as one unit . |
| 56 | M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 6.0 sq mm (FRLS) in and including PVC casing & capping non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 6.0 Sq mm (FRLS) of continuous earth wire green in colour including taking down old sub main wiring complete all as specified and directed .NOTE: Three runs of 6.0 sqmm cable and one run of PVC casing & capping shall be paid as one unit . |
| 57 | Maintenance and servicing of split type 1.5/2 Ton AC including cleaning filter, washing with soap solution after removing from site and refixingthe same complete all as specified and as directed. |
| 58 | S&F in replacement ofhermitically sealed outdoor compressor unit including brazing/welding and leakage testingafter completon of job for 1.5 Ton Split type AC complete all as specified and as directed . |
| 59 | All as per item No. 58.00 here-in-before but for 2.0 Ton capacity |
| 60 | M & L for gas charging including comissioning and testing in split AC 1.5/2.0 TR Ton complete all as specified and as directed. |
| 61 | S&F in replacement of condensing coil copper including soldering with existing systemfor 1.5/2 .0 Ton AC complete all as specified and as directed . |
| 62 | S&F in replacement of outdoor fan motor for 1.5 ton AC complete all as specified and as directed . |
| 63 | S&F in replacement of outdoor fan motor for 2.0 ton AC complete all as specified and as directed . |
| 64 | S&F in replacement of Running Capacitor of capacity36 MFD+ 5% complete all as specified and as directed . |
| 65 | S&F in replacement ofRunning Capacitor of capacity60 MFD + 5% complete all as specified and as directed . |
| 66 | S&F in replacement ofRunning Capacitor of capacity2.5 MFD + 5% complete all as specified and as directed . |
| 67 | S&F in replacement of indoor filter of Hi-wall type indoor unit suitable for existing make indoor units Air conditioners of capacity 1.5/2 TR complete all as specified and as directed . |
| 68 | Disconnection and removing the unserviceable PCB from the indoor unit ofSplit type Air conditioner and S & F new PCB suitable for the existing Makes of Air conditioners of capacity 1.5/2 TR complete all as specified and as directed . |
| 69 | Disconnection and removing the unserviceable PCB from the outdoor unit of invertor type Split type Air conditioner and S & F new PCB suitable for the existing Makes of Air conditioners of capacity 1.5/2 TR complete all as specified and as directed . |
| 70 | Disconnection and removing the unserviceable indoor blower motor from the indoor unit of 1.5 TR /2.0 TRSplit type Air conditioner and S & F newindoor blower motor suitable for the existing Makes of 1.5 TR/2.0 TR split type Air conditioners complete all as specified and as directed . |
| 71 | Disconnection and removing the unserviceable indoor swing motor from the indoor unit of 1.5 TR Split type Air conditioner and S & F newindoor swing motor suitable for the existing Makes of 1.5 TR split type Air conditioners complete all as specified and directed by Engineer-in-charge |
| 72 | Disconnection and removing the unserviceable indoor swing motor from the indoor unit of 2 TR Split type Air conditioner and S & F newindoor swing motor suitable for the existing Makes of 2 TR split type Air conditioners complete all as specified and as directed . |
| 73 | S&F in replacement of copper pipe of size 1/2\" dia with necessary fixing arrangements for such as welding, brazing, nut, bolts and testing complete all as specified and as directed . |
| 74 | S&F in replacement of copper pipe of size 1/4\" dia with necessary fixing arrangements for such as welding, brazing, nut, bolts and testing complete all as specified and as directed . |
| 75 | S&F in replacement ofsuitable stand (bracket) for outdoor unit of 1.5/2 ton split air conditioner complete all as specified and as directed. |
| 76 | M & L for gas charging with R134A including comissioning and testing complete of 40/80 Ltrs capacity water cooler complete all as specified and as directed . |
| 77 | Earthing complete with galvanized iron earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the Galvanised iron earth wire 4mm size, by means nut, bolt, check nuts and washer as earth lead protected by provision of GI light grade pipe 20mm bore incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point with fixing arrangement CI funnel wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exc 50 mtr all as per electrical plate No.3 of SSR Part I and connecting to earth test point including testing complete all as specified and as directed. |
| 78 | S & F in replacement ofGI 4.0 mm dia with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and as directed. |
| 79 | Taking down old unserviceable LT UG cable from existing position and Supply & laying,connectingand commissioning ofLT UG cable10 sqmm 4 core, 1100 volts grade XLPE insulated armoured heavy duty electric cables with aluminium conductor including connecting with suitable size of cable glands lugs etc. laid in trenches or fixed on walls complete all as specified and as directed |
| 80 | All as per item No 79.00 here-in-before but LT UG Cable of size 16 sqmm 4 core |
| 81 | All as per item No 79.00 here-in-before but LT UG Cable of size 25 sqmm 4 core |
| 82 | All as per item No 79.00 here-in-before but LT UG Cable of size 50 sqmm 3.5 core |
| 83 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out soft/loose soil for laying cables/pipes/erection of poles etc. complete all as specified and as directed. |
| 84 | Returning filling in, with excavated soils including spreading, levelling, watering and well ramming in layers n.exc. 25 cms thick complete all as specified and as directed. |
| 85 | Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. |
| 86 | M&L for sand cushioning with sand in two layer,first layer of 80mm thick before laying of cable and second layer of 150mm thick after laying of cable in trenches/ducts for cable including consolidation of each layer complete all as specified and as directed. Note :Punned thickness of sand cusioning only shall be measured for the purpose of payment . |
| 87 | Supply and Laying unreinforced precast concrete cable cover class LV 1 flat size of size 250x150x40 mm for LT Cable all sizescomplete all as specified and as directed. |
| 88 | Cutting the existing hardstanding not less than 25cm in deep and 45cm in width for laying of underground cable through GI pipe and making good the disturbed surfaces complete all as specified and as directed. |
| 89 | S & FGItubing50 mm dia light grade ISI markedlaid in trenches completewithallaccessoriessuchasTees,union , bend ,elbownipple reducer etc asrequired forprotection of UG Cable on floor ,poleetc complete all as specified and as directed . |
| 90 | S & F in replacement of MCCB 63 Amps 16 KA, 4 Pole, 415 V 50 Hz including all connections complete all as specified and as directed . |
| 91 | S & F in replacement of MCCB 100 Amps 25 KA, 4 Pole, 415 V 50 Hz including all connections complete all as specified and as directed . |
| 92 | All as per item No. 91.00 here-in-before but MCCB 160 Amps 36 KA, 4 Pole, 415 V 50 Hz |
| 93 | All as per item No. 91.00 here-in-before but MCCB 250 Amps 36 KA, 4 Pole, 415 V 50 Hz |
| 94 | Painting of existing LT panels by using two coats of synthetic enamell paint including preparion of old surfaces complete all as specified and as directed. |
| 95 | Repair to existing LT panels front and rear doors of locking arrangements by using suitable hinges complete all as specified and as directed . |
| 96 | Maintenance and servicing of DG Sets (B check) comprising prime mover and alternator with accessories, control panel and connected electric circuits with various type of sensors etc including checking lubricating oil, coolant, filters, V-belt, self starter, battery power, gauges and other connected accessories, cleaning of alternator with vaccum cleaner, attending faults of AMF panels and replacing the defective parts (as per B check i.e. filters, gasket kits, O ring, oil, coolant etc)and identifying malfunction of theDG Set of capacity 62.5 KVA complete all as specified and as directed .Note :- (a) Spares of DG Set will be measured and paid seperately under relevent item of the CA catered as supply only.(b)Minor spares like nuts/bolts, washers, oil seal, gaskets, cotton waste, clamps shall deemed to be included in the rate quoted.(c) Labour component for fixing the spares during the servicing including testing the DG setis deemed to be included in the quoted rate. |
| 97 | Dismantling radiator assembly from the engine of 62.5 KVA capacity DG sets by disconnecting inlet and outlet connection overhauling / servicing the radiator, descaling and servicing the radiator internally and externally by using chemicals, including soldering the copper tubes and tank etc for arresting leakage, re assembling with necessary welding and additional bracket as required including refixing, reconnecting and testing for proper functioningcomplete all as specified and as directed. |
| 98 | Dismantling of fuel injection pump assembly complete from the engine of DG Set of capacity 62.5 KVA , servicing, over hauling,replacement ofvalves, washers etc., assembling, calibration, setting for proper function, reassembling and re-fixing complete all as specified and as directed . |
| 99 | Disconnecting and taking down outgoing cables from the DG Set of capacity 62.5 KVA and cutting removing the burnt cable ends and thimbling and refixing back including provision of cable glands, lugs, tools and testing complete all as specified and as directed . |
| 100 | Supply only (in replacement) spin on fuel filter (pre and fine filter) element with O ring for DG Set of capacity 62.5 KVA |
| 101 | Supply only (in replacement) dry type Air filter element Inner and Outer unit as required at site with O\" Ring of suitable for DG Set of capacity 62.5 KVA |
| 102 | Supply only (in replacement) Lub oil filter element with O Ring suitable for DG Set of capacity 62.5 KVA |
| 103 | Supply only (in replacement) by pass filter element with O ring of suitable for DG Set of capacity 62.5 KVA |
| 104 | Supply only (in replacement) V-belt suitable for DG Set of capacity 62.5 KVA |
| 105 | Supply only (in replacement) of water pump assy suitable for DG Set of capacity 62.5 KVA |
| 106 | S & F in replacement of common rail diesel sensor suitable for DG Set engine complete all as specified and as directed . |
| 107 | S & F in replacement ofwater outlet and inlet hose pipe from radiator to Engine and backfrom Engine to radiatorfor DG Set of capacity 62.5 KVAcomplete all as specified and as directed. |
| 108 | S & F in replacement of Lub oil pipe armoured of suitable length and socket size complete all as specified and as directed. |
| 109 | S & F in replacement of Anti vibration rubber pad for side radiatorfor DG Set of capacity 62.5 KVA complete all as specified and as directed. |
| 110 | S & F in replacement of Lub oil pressure guage0 to 10 kg / sq cmfor DG Set of capacity 62.5 KVA complete all as specified and as directed. |
| 111 | Supply and top up coolent oil complete all as specified and as directed. |
| 112 | Supply and top up engine oil 15W40 grade complete all as specified and as directed. |
| 113 | Supply and replace battery connecting single core copper cable 16sqmm with battery terminal made of brass with nuts/bolts/washercomplete all as specified and as directed. |
| 114 | Supply and top up battery distilled water complete all as specified and as directed. |
| 115 | S & F in replacement of SMPS battery charger 12V/24V DC including all fixing accessories and re-wiring with suitable size copper conductor FRLS grade PVC insulated two core cable drawn through PVC conduit not less than 20mm dia as required at site and complete all as specified and asc directed. |
| 116 | Disconnecting, dismantling 12V/24V battery charging alternator assembly replacing the unserviceable burnt coil assembly, re-assembling, refixing to engine and testing for satisfactory charging of battery complete all as specified and directed. |
| 117 | S & F in replacement of AVR (Auto Voltage Regulator) suitable for 62.5 KVA capacity Gen Set having input voltage 2 phase + neutral sensing voltage 415 output voltage 95V DC, output current 4 A DC voltage regulation +/- 1% average volts, over excitation current tripping fuse protection 4A, fast acting and frequency 50Hz complete all as specified and directed. |
| 118 | S & F in replacement of Digital DG controller suitable for any type DG Set of any capacity and connecting with existing electrical circuit complete all as specified and as directed. |
| 119 | S & F in replacement of Diods set (Rectifier) of main alternator of DG Set of capacity 62.5 KVAcomplete all as specified and as directed. |
| 120 | S & F in replacement of contactor 4 pole, 63A, coil volt-240volts, AC 50Hz com plete all as specified and as directed |
| 121 | S & F in replacement of contactor 4 pole, 100A, coil volt-240volts, AC 50Hz com plete all as specified and as directed |
| 122 | S & F in replacement of CT coil with CT Ratio 100/5A, 5VA Cl 1.0 accuracy all as per IS 2705-1992 complete all as specified and as directed. |
| 123 | S & F in replacement offuse unit 12 V DC (as per sample) suitable for DG Set control pane complete all as specified and as directed. |
| 124 | Minor repair / cleaning of fuel tank, removing sludge, arresting leak using metal paste / sealent or by welding / soldering, replacement of diesel receiver pipe from lock to tank with clamp set all as required at site for DG Set of capacity 62.5 KVAcomplete all as specified and as directed. |
| 125 | Minor repair to canopy such as to hinges, locking arrangement etc and painting inside /outside area of DG Set 62.5 KVA comprising engine, alternator, genset panel board and fuel tank and canopy, as per standard approved colour code with one coat of synthetic enamel paint cleaning scrubbing of all surface including writing by paint the SM/MES numbers etc complete all as specified and as directed. |
| 126 | Dismantling, removing the self starter, motor from the engine of DG Set of capacity30 / 45 KVA , opening the self starter body and overhauling / servicing, replacement of carbon brushes with holders, contact plates, jumping leads and seals, re-varnishing the field coil, armature, re-assembling, testing for smooth functioning and re-fixing with the engine and connecting complete all as specified and as directed. |
| 127 | S&F asbestos rope 12 mm dia wrapped over the exhaust pipe and painting with heat proof paint of approved colour including taking down the old rope complete all as specified and as directed. |
| 128 | S & F in replacement of volt meter digital type with 01 xselector switch complete all as specified and as directed. |
| 129 | S & F in replacement of ampere meter digital type with01 x selector switches & CTs of suitable rating complete all as specified and as directed. |
| 130 | S & F in replacement ofLED phase indicator lamp assy RYB complete all as specified and as directed. |
| 131 | S & F in replacement of water separator suitable for DG sets of capacity 62.5 KVA complete all as specified and as directed. |
| 132 | Earthing complete with galvanized iron earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the Galvanised iron earth strip 32x6 mm size, by means nut, bolt, check nuts and washer as earth lead protected by provision of GI light grade pipe 40mm bore incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point with fixing arrangement CI funnel wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exc 50 mtr all as per electrical plate No.3 of SSR Part I and connecting to earth test point including testing complete all as specified and as directed. |
| 133 | S&F DG Set diesel tank lock (as per sample) with fixing accessories complete all as specified and directed. |
| 134 | Checking of AMF panels including replacement of unserviceable parts such as relays, timers, power contactors, Auxilary contactors, defective copper wiring, MCCBs etc. for DG Set, complete all as specified and directed.Note: - Spare parts shall be measured and paid separately under Supply only items |
| 135 | Supply only Auxiliary Contactor 240V 3 No & 1 NC |
| 136 | Supply only ON and OFF delay timer 240 V AC |
| 137 | Supply onlyEarth fault relay. |
| 138 | Supply onlyOver load relay. |
| 139 | Supply onlyUnder voltage relay. |
| 140 | Supply onlyDc power contactor for auto starting 12V |
| 141 | Supply only Power Contactor MCX22, 4 Pole |
| 142 | Supply only Power Contactor MCX11, 4 Pole |
| 143 | Supply only Power Contactor MCX 33, 4 Pole |
| 144 | S & F in replacement ofPower Contactor MNX70, 3 Pole, 415V including necessary wiring complete all as specified and as directed . |
| 145 | S & F in replacement ofPower Contactor MNX110, 3 Pole, 415V including necessary wiring complete all as specified and as directed . |
| 146 | S & F in replacement of indoor type Auto mains failure panel board, CPRI manufactured made of CRCA sheet of 2mm thickness consisting of two power contactors 4P, 415V,100 A current rating with electrical interlocking facility, Auxilary power contactors, under/ over voltage relay, single phase preventer , SMPS 12V DC output for auto charging of battery and self starter, MCB\"s, relays pre wired and synchronized with DG set having auto/ manual selector switches withall necessary itemscomplete all as specified and as directed . |
| 147 | Dismantling of 62.5 KVA capacity alternator from Generator after Dismantling from Generator shifting to workshop, taking out burnt out winding from stator & rotator, cleaning thoroughly and rewinding the stator with suitable guage of super enameled copper conductor similar to that of existing size including necessary insulating material varnishing, heating, reassembling of alternator, bringing back to the site, refixing and installation and foundation with proper alignment, testing and commissiong complete all as specified and as directed. Note :- Transportation from the site to workshop and backand labour elementis deemed toincluded in rate quoted. |
| 148 | S & F in replacement of compressor unit for 40/80 Ltrs capacity of water cooler including comissioning and testing complete all as specified and as directed . |
| 149 | S & F in replacement of thermostat for water cooler ofexisting capacity complete all as specified and as directed . |
| 150 | S & F in replacement of capacitor of 10 MFD for water cooler complete all as specified and as directed . |
| 151 | Disconnection and removing the unserviceable voltage stabilizer and replace the unserviceable items such as PCB/control board etc and refixing back in its original position testing as per existing makes of capacity 2/4/5 KVA complete all as specified and as directed Note: Cost for replacement of items will be measured and paid under respective items as Supply only |
| 152 | S & F in replacement of lightning conductor air termination, single pointed aluminium rod 12 mm dia and 300 mm long conforming to IS-2309including fixing of MS clamps, fixing screws complete all as specified and as directed. |
| 153 | S & F in replacement of Aluminium strip 25 mm x 3.15 mm fixed with FRP saddles & fixing screws of size not less than 4 mm dia and 32 mm long for roof conductors and down conductors above ground complete all as specified and directed. |
| 154 | S & F in replacement ofgalvanised iron earth strip 32 mm x 6 mm with saddles and fixing screws etc. down conductors above ground complete all as specified and as directed. |
| 155 | S & F in replacement ofCopper earth strip 20 mm x 3.15 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and as directed. |
| 156 | Supply and laying in replacement ofroad croosing or in floor / fixing along the pole /wall, 40 mm bore galvanized iron tubing lightgrade including all fittings complete for protection of cable / GI strip.(for ring conductor) complete all as specified and as directed. |
| 157 | M&L double wall corrugated HDPE pipe ( ISI marked) of outer dia 50mm and 38mm inner diawith smooth internal and profiled external surface, non pressure type, laid in trenches/ floors/ ductor fixed on walls /poleincluding alconnections, accessories like socket, couplers, bends etc., for protection of LT cable complete all as specified and as directed . |
| 158 | S & F in replacement of time switch 240V single phase of 20 Amp rating with contactor fitted inside steel enclosurecomplete all as specified and as directed. |
| 159 | S&F in replacement of PVC insulated , unsheathed,unarmoured 1100 volt grade 2.5sqmm with strandedcopper conductor cable of size 2.5 Sqmm drawn through FRP pole complete all as specified and as directed. |
| 160 | S & F in replacement of post top lantern LEDlight fitting 20 Watt 230 V AC outdoor type with decorative post top for 360 degree indirect light with impact and corrosion resistant of IP 66 protection and lamp energy saving and environmental friendly long life aesthetically designed with symmetrical light distribution, spun aluminium landscape with all connections complete all as specified and as directed. |
| 161 | S & F in replacement ofFRP junction box with 4 way connectors heavt duty suitable for mounting MCB SP 6 Amps - 01 No with locking hinge and aluminium clamp made out of 32X6mm thick complete all as specified and as directed. |
| 162 | S& F in replacement of LED flood light fitting 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant with driver complete all as specified and as directed. |
| 163 | S& F in replacement of Aviation obstruction light 30W, 240V including all connections complete all as specified and as directed. |
| 164 | S&F in replacement of LED bollard lighting of 10W energy saving and environmental friendly long life aesthetically designed aluminium landscape IP 65 luminare for diffused lighting with high power LED as light source including all connections complete all as specified and as directed. |
| 165 | S&F in replacement of LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed . |
| 166 | S & F in replacement of Cross arms ,bracings,supports,clamps and back plate fabricated from structural steel sections including nuts ,bolts, in any shape or size as indicated or directed and inclusive of two coat of aluminium paint over a coat of red oxide primer complete all as specified and as directed. |
| 167 | Dismantling the centrifugal /submesible pump set of capacity 0.5 HPand transportation to workshop for replacing unserviceable parts such asimpeller,shaft, bearing, winding etc and reconnecting back the pumpset to its original position after repair and testing complete all as specified and as directed. |
| 168 | All as per item No. 167.00 here-in-before but ofcapacity 1.0 HP |
| 169 | Disconection and removing the defective DOL starter and S & F the new DOL starter three phase 440 Volts , 50 Hz suitable for motor capacity up to 0.5 HP testing complete all as specified and as directed. |
| 170 | Disconection and removing the defective DOL starter and S & F the new DOL starter three phase 440 Volts , 50 Hz suitable for motor capacity up to 1 HP testing complete all as specified and as directed. |
| 171 | S & F in replacement of current relays suitable for single phase DOL startertesting complete all as specified and as directed. |
| 172 | S & F in replacement of PVC foot valve of 50 mm bore complete all as specified and as directed. |
| 173 | S & F in replacement of PVC foot valve of 40 mm bore complete all as specified and as directed. |
| 174 | S & F in replacement of PVC foot valve of 25 mm bore complete all as specified and as directed. |
| 175 | S&F in replacement of CPVC ball valve of 25mm size complete all as specified and as directed. |
| 176 | S&F in replacement of CPVC ball valve of 32mm size complete all as specified and as directed. |
| 177 | S&F in replacement of CPVC ball valve of 40mm size complete all as specified and as directed. |
| 178 | S&F in replacement of CPVC ball valve of 50mm size complete all as specified and as directed. |
| 179 | Supply & laying in replacement of CPVC pipes 25mm bore,SDR 13.5 and plain CPVC SDR 11 fittings on wall/ceiling or laying in floors complete all as specified and as directed. |
| 180 | All as per item No 179.00 here-in-before but CPVC pipe of 32 mm bore |
| 181 | All as per item No 179.00 here-in-before but CPVC pipe of 40 mm bore |
| 182 | All as per item No 179.00 here-in-before but CPVC pipe of 50 mm bore |
| 183 | S&F in replacement of CPVC brass elbow of 25mm size complete all as specified and as directed. |
| 184 | S&F in replacement of CPVC brass elbow of 32mm size complete all as specified and as directed. |
| 185 | S&F in replacement of CPVC brass elbow of 40mm size complete all as specified and as directed. |
| 186 | S&F in replacement of CPVC brass elbow of 50mm size complete all as specified and as directed. |
| 187 | S&F in replacement of CPVC brass tee of 25mm size complete all as specified and as directed. |
| 188 | S&F in replacement of CPVC brass tee of 32mm size complete all as specified and as directed. |
| 189 | S&F in replacement of CPVC brass tee of 40mm size complete all as specified and as directed. |
| 190 | S&F in replacement of CPVC brass tee of 50mm size complete all as specified and as directed. |
| 191 | S&F in replacement of CPVC male brass threaded adaptorof 25mm size complete all as specified and as directed. |
| 192 | S&F in replacement of CPVC male brass threaded adaptorof 32mm size complete all as specified and as directed. |
| 193 | S&F in replacement of CPVC male brass threaded adaptorof 40mm size complete all as specified and as directed. |
| 194 | S&F in replacement of CPVC male brass threaded adaptorof 50mm size complete all as specified and as directed. |
| 195 | S&F in replacement of CPVC female brass threaded adaptorof 25mm size complete all as specified and as directed. |
| 196 | S&F in replacement of CPVC female brass threaded adaptorof 32mm size complete all as specified and as directed. |
| 197 | S&F in replacement of CPVC female brass threaded adaptorof 40mm size complete all as specified and as directed. |
| 198 | S&F in replacement of CPVC female brass threaded adaptorof 50mm size complete all as specified and as directed. |
| 199 | S&F in replacement of CPVC UNIONof 25mm size complete all as specified and as directed. |
| 200 | S&F in replacement of CPVC UNIONof 32mm size complete all as specified and as directed. |
| 201 | S&F in replacement of CPVC UNIONof 40mm size complete all as specified and as directed. |
| 202 | S&F in replacement of CPVC UNIONof 50mm size complete all as specified and as directed. |
| 203 | Construction of 200mm thick PCC solid block wall masonary valve chamber built in CM 1:6 with 150mm thick PCC foundation 1:2:4 type B-1, coping 50mm thick finished even and smooth, rendering 10mm thick in cement mortar (1:6), finished fair and and even externally including excavation earthwork in any strata, 6mm thick MS sheet cover fixed on angle iron frame 25x4mm embedded in PCC coping with locking arrangement and mild steel hold fast, mild steel handles and painting to steel surface with two coats of black bituminus paint over one coat of red oxide primer etc, for internal size 600x600x600mm including the demolishing existing PCC chamber complete all as specified and as directed |
| 204 | Taking down old unserviceable submersible cable from existing position and Supply & laying,connectingand commissioning ofsubmersible copper cable 440 volts gradeflat 4 sqmm 3 core complete all as specified and as directed |
