Tender For Interior & Electrical Data Cabling Furnihsing Work Of Lakshmikantapur Branch Façade of Entrance Door Providing and fixing in position Aluminium composite panel Boxing with PVDF coating & LDPE core laminated Eurobond / Altobond/ Alukbond Exterior Grade 4 mm thick with composite of ( 0.5mm-3mm0.5mm) including fabrication for the same with aluminium sections, required hardware, silicon sealant (Dow Corning 789) masking tape, necessary scaffolding etc. as detailed in drawing no (11) complete in all respects. False Ceiling ( Armstrong) Providing & fixing in position false ceiling in Armstrong 600 x 600 mm x 15/16 mm Dune Supreme RH 99 Prima tile with Tegular edge framework as specified by Armstrong Co. With suspenders wherever required. Making necessary framework for A.C. ducting,, if any, and necessary cutouts for diffusers and light fittings, taping and finishing to proper line & level, including making grooves and trap doors for A.C. unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1”x 1” for edges including finishing with White Plastic Emulsion paint etc. complete in all respects. ( Note:- Only the plan area will be measured for payment. No extra payment will be made for cutouts, grooves, mouldings etc.) False Ceiling ( Gypsum Board) Providing & fixing in position false ceiling in Gypboard 12 mm thick for horizontals & verticals fixed over G.I. framework as specified by India Gypsm Co. Ltd. Including trap doors for A.C.unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1”x 1” for edges including finishing with White Plastic Emulsion Paint etc. complete in all respects. ( Note:- Only the plan area will be measured for payment. No extra payment will be made for cutouts, grooves, mouldings etc.) Contractors to visit site to verify whether some existing falseceiling sections could be reused and quote accordingly. Painting Providing & applying White Plastic Emulsion paint of Asian Paints/ ICI Dulux/ Berger and Sporty YellowX104 shade of Royal Luxury Emulsion of Asian Paints in minimum 2 coats including scrapping, opening of existing cracks, filling up of “v” cracks with epoxy expandable putty to required depths making good week plastered/ un-plastered surfaces with cement plaster Sft Sft Sft 64 340 957 Design Group - Architects Page 2 5. 6. wherever required. Item to include Plaster of Paris, primer, palti & making good existing surface to receive new paint including cleaning on completion of painting work etc. complete in all respects. Entrance Door Providing and fixing Entrance Door ( glazed) as per drawing no. 11 in Silver powder coated aluminium door section ( Jindal make) in top and bottom, glazed with 12 mm thick toughened glass of approved make with etching and frosting. item to include floor springs, lock, all necessary hardware of Stainless Steel finish as approved by the Project Consultant/ Bank complete in all respects. Front Office Counter Providing and fixing in position Front Office Counter 2’- 6” wide as per drawing No ( 1-A, 1-B, 1-C, 1-D & 15) comprising of the following complete in all respects:- i) Working top made with 25 mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1 ¼ “ x 1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½“x 1” T.W. beading patti with melamine finish. ii) Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades. iii) Vertical drop ( horizontal band) shall be provided on the fascia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1mm thick groove shall be provided at the joint of two different shades of laminate. iv) Glazed partition above working top to be provided with 12mm thick clear glass cut to the standard shape fixed to partition as per fixing details and to boxing with concealed S.S. finished ‘D’ brackets as shown in the drawing . The exposed edges of the glass shall be finished in mirror polish. v) 3’- 10” high Boxing (10”x 10” ) made with 18mm thick plywood finished with 1mm thick laminate including providing and fixing 6mm thick square frosted glass at a height 3’- 2” above finished floor level. vi) 1’-9” high Boxing ( 5”x 5” ) made with 12mm Sft Sft 2900 42 Design Group - Architects Page 3 7. thick plywood finished with 1mm thick laminate. vii) Vertical supports made with 18 mm thick plywood finished with enamel paint. viii) Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. ix) Footrest made with T.W. member of size 4”x 1½” finished with french polish. x) Drawer units as per drawing shall be provided with multipurpose Godrej locks in each drawer. Fascia of drawer unit shall be finished with 1mm thick laminate and all other side shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant/ Bank. xi) Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/ Telephone wire conduiting. The item to included all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the front. Vertical drop and also in the 10”x10” boxing as shown in the drawing . Necessary beadings with melamine polish for fixing the glass are to be provided. Cash Counter Providing and fixing in position Cash Counter 2’-9” wide as per drawing No ( 2-A, 2-B, 2-C, 2-D, 2-E, 2-F) comprising of the following : i) Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1¼”x 1” Teak Wood moulding finished with melamine polish . Inside edge will be provided with ½”x 1” T.W. beading patti with melamine polish. ii) Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminate of two different shades. iii) Vertical drop (horizontal band) shall be provided on the fascia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1mm thick groove shall be Rft 13.5 Design Group - Architects Page 4 provided at the joint of two different shades of laminate. iv) Glazed partition of 1’ -4” height above working top provided with 12mm thick toughened and frosted glass besides non -transparent film from inside fixed to partition as per fixing details and to boxing with concealed S.S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish. v) Transaction top shall be provided with 12mm thick toughened glass ( partly glazed partly frosted) fixed horizontally with concealed Stainless Steel D bracket. Both exposed edges ( inside and outside) shall be moulded and finished in mirror polish. vi) Glazed partition having height 1’.0” above the transaction top ( in facia) shall be provided with 12 mm thick glass (clear) with cut out of 8”x 4” as per drawing. The edges of cut out and the top edge of glass are to be mirror polished and to be fixed to partition as per fixing detail and to boxing with concealed S.S. finished ‘D’ brackets as shown in glass (Clear)above the slit to be fixed to partition as per fixing details and to boxing with concealed S.S. finished ‘D’ brackets as shown in the drawing . The exposed edges shall be finished in mirror polish. vii) 7’ -7” high Boxing (10”x10”) made with 18mm thick plywood as per drawing with 1 -6” horizontal extension at the top including providing and fixing 6mm thick square frosted glass at a height of 5” -11” above Finished Floor level. viii) 1’ -9” high boxing (5”x5”) made with 12mm thick plywood finished with 1 mm thick laminate are to be provided. ix) Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. x) Footrest made with T.W. member of size 4”x1½”finished with french polish. xi) Drawer units as per drawing shall be provided and each drawer should have vertical partitions for keeping the currency notes and multipurpose Godrej locks. Fascia of drawer unit shall be finished with 1mm thick laminate and all other side shall be finished with white enamel paint. The drawers will be provided Design Group - Architects Page 5 8. 9. 10. with handles ( Stainless Steel finish) and channels as per approval of the Project Consultant/Bank. xii) Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/ Telephone wire conduiting. The item to include all necessary hardware and fitting in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beading with matching melamine polish for fixing the glass are to be provided as per drawing/ as directed. Solid Full Height Partition Providing & fixing in position solid Full Height Partition in frame work including door in 2’x2’ grid (horizontally and vertically) comprising of 2”x1½” T.W. Section with 6mm thick plywood on both side finished with 1mm thick laminates of approved make and colour as shown in drawing no. 17. Item to include 2”x2” T.W. member for door frame. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. ( Note: in case of false ceiling, the vertical T.W. members to be fixed with real ceiling but the area of partition payable will be below the false ceiling only.) Column Panelling Basic specification same as Solid full ht Partition , wooden sections to be used are of 1.5”x 1” with ply and laminate finished from floor to 2’6” with rounded projected moulding polished & finished and again from 7’0” to falseceiling. In -between portion milky white pvc sheet with ACP sheet on top jali cutting pattern as per design all around the column backlighted with LED lighting strips with necessary driver etc providing & installing all as required complete and operational in all respects to the satisfaction of Consultant /Bank. Partly Glazed Full Height Partition Providing and fixing in position partly glazed Full Height Partition work as shown in the drawing nos.(3) & (4) including door as shown in the drawing No. (13) in frame work at 2’x2’ grid ( horizontally and vertically) comprising of 2”x 1 ½”T.W. section and /or as per frame work shown in the drawing with 6mm plywood on both sides finished with 1mm thick laminates of approved shade and colour as shown in Rft Sft Sft 9160 85 Design Group - Architects Page 6 11. 12. 13. drawings. Item to include 8mm thick glass with etching and frosting as per design and 2”x2” T.W. member for door side and glass side and T.W. door frame to take 8mm thick glass with etching and frosting. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. ( Note: In case of false ceiling the vertical T.W. members to be fixed with real ceiling but the area of partition payable will be below the false ceiling only.) Partly Glazed Partition for Cash Cabins Providing and fixing in position 7’ -7” high partly glazed partition for Cash Cabins as per drawing nos. (2 - A, 2 -B, 2 -C, 2 -D, & 2 -E ) including door drawing no. (12) in frame work at 2’x2’ grid ( horizontally and vertically) comprising of 2”x 1½” T.W. Section and/or as per frame work shown in the drawings with 6mm plywood on both side finished with 1mm thick laminates of approved shade and colour as shown in drawings. Item to include 8mm thick glass with etching and frosting as per design and 2”x2” T.W. member for door sides and glass sides and T.W. door frame to take 8mm thick glass with etching and frosting. The door will be provided with T.W. louvers finished in melamine polish of matching laminate colour. The doors are also to be provided with Godrej Night Latch. Two wooden trays are also to be provided as per drawing. Necessary cut -outs are to provided in the glass and the edges of the glass cut -outs are to be finished in mirror polish . All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish / hardware, door closers , Godrej lock and wood preservative paint etc. as per list of approved material and approved by the Project Consultant/ Bank complete in all respects. Partly Glazed Low Height Partition Providing and fixing in position partly glazed low height partition (2.5” thick) in frame work with T.W. vertical members at 2’c/c and 3 horizontal members at equal distance comprising of 2”x 1½” T.W. Section with 6mm plywood on both side finished with 1mm thick laminates of approved make and shade as shown in drawing no. (14) or (3). Item to include 12 mm thick glass ( clear/frosted) to be fixed as shown in drawing . The exposed edges of the glass to be finished in mirror polish. T.W. runner should be melam ine polished in matching colour of laminate etc complete in all respects. Manager’s Table/ Officer’s Table Providing and fixing in position Manager’s Table of Sft Sft Sft 160 210 22 Design Group - Architects Page 7 14. 15. size 5’ -6”x 2’ -6” as per drawing no ( 6) / Officer’s Table of size 4’ -6”x 2’ -3” as per drawing no (5) including Side Storage (credenza) by using 25mm thick plywood for top and 18mm thick plywood for all other horizontal and vertical members. Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. Footrest made with T.W. member of size 4”x1 ½” finished with french polish. Side Storage ( Credenza) as per drawing shall be provided. Fascia of Side Storage ( Credenza) shall be finished with 1mm thick laminates as shown in the drawing and all other side shall be finished with white enamel paint. The Side Storage ( Credenza) shall be provided with handles ( Stainless Steel finish) and channels as per approval of the Project Consultant/ Bank. All exposed plywood surfaces to be finished with 1mm thick laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1”x ¼” T.W. lipping. All exposed T.W. sections to be melamined and internal surfaces to have white enamel paint as directed. Item to include plywood boxing, all necessary hardware and fitting in Stainless Steel finish, lipping to all edges etc. complete in all respects. Staff Table Providing and fixing in position Staff Table of size 4’ 0 ”x 2’0” as per drawing No (5) by using 25mm thick plywood for top and 18mm thick plywood for all other horizontal and vertical members. Telescopic CPU Stand/ ready made Keyboard tray shall be provided. Drawer units as per drawing shall be provided with multipurpose Godrej locks in each drawer. Fascia of drawer unit shall be finished with 1mm thick laminate and all other side shall be finished with white enamel paint. The drawers will be provided with handles ( stainless Steel Finish) and channels as per approval of the Project Consultant/ Bank. All exposed plywood surfaces to be finished with 1mm thick. laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1”x ¼” T.W. lipping. All exposed T.W. section to be melamined and internal surfaces to have white enamel paint as directed. The item to include plywood boxing, all necessary hardware and fitting in Stainless Steel finish, lipping to all edges etc. complete in all respects. Full Height Storage / Low Height Storage / Back Storage ( Credenza ) Providing and fixing in position Full height Storage / Low Height Storage / Back Storage ( Credenza) as shown in Drawing No (8), (9) & (10) respectively using Plywood of required thickness finished with 1mm thick laminates as shown in the drawing and all other side shall be finished with white enamel paint as detailed therein. The Storage Units shall be provided with handles(Stainless Steel finish) as per approval of the Nos Nos 3(1+ 2 ) x Design Group - Architects Page 8 16. 17. 18. 19. 20. Project Consultant/ Bank. All exposed plywood surfaces to be finished with 1mm thick laminate of approved make & shade and all exposed edges of plywood to have 1”x ¼” T.W. lipping. All exposed T.W. sections to be melamined in matching colour laminate and internal surfaces to have white enamel paint as directed. Item to include all necessary hardware and fitting in Stainless Steel finish, Godrej multi purpose locks including magnetic ball catcher etc. complete in all respects. Sofa Supplying, making and providing sofa sets in teak wood framework of 75mm. x 38mm. and 50mm. x 38mm. with cylindrical spring, neyars, 100mm. thick ‘ U’ foam for seat and 75mm. thick for back with 12mm. thick high density polyurethane foam covered with white cloth and upholstered with fabric / leather look alike rexene ( basic price upto Rs.250 per M ) treated with fabguard treatment of approved make and as required / directed. 3 -seater. Sofa Side unit General specification consists of 18mm ply box 1’6”x1’6”x1’6” laminated and finished, as per matching laminating schedule bottom surface painted and having buffers at the bottom. Vertical Blinds Supply and fixing of vertical blinds for windows etc, colour & pattern as chosen of 4” wide with sliding & tilting mechanism complete. Writing Ledge Writing Ledge size 3’ 6”x1’0”x6” fixed to wall – made out of 1 ½” blockboard laminated, edges lipped polished and finished, with ½” glass machine polished edges slotted partitions about 5” apart, held with D brackets, top of ½” glass machine polished edges clipped to the blockboard structure. Supply providing & fixing miscellanies items as below: a) Complaint & suggession box made of 19mm BWR blockboard laminated and finished with one openable panel in front with body lock. Size 1’0”x1’6”x6” depth with slit in front for receiving complaints. Writing on top in enamel paint / stickers such as name, address, purpose etc as directed by client. b) Letter box same as above as complaint & suggession box. c) Notice board 3’x2’ made of imported highly transparent PVC sheet 8 mm thk beveled edges machine polished, 2nos held together at 4 corners by matt SS spacers to be used for putting up clients business promotional posters from time to time. Sft Nos Nos Sft Nos No No Nos 183 22 641115 Design Group - Architects Page 9 21. Flush door 1 ½” thick with timber frame consisting of top, bottom , lock rail and side styles of well seasoned timber 4” wide with BWR 4mm thick ply pasted on either sides of the frame work and skinning of 1mm laminate on either sides, including fittings such as brass hinges , door stopper ,door closer, buffer, Godrej Aldrop handle and lock etc. all as required. Inclusive of 2 coats of enamel paints over one coat of wooden primer in non-laminated places. ¼” T.W. lipping on all exposed edges. Doorframe (3” x 2”) to be fitted and fixed complete including a protective coat of painting at the contact surface of the frame. (Sal).
