|
| 1 | Demolition of cement concrete (unreinforced) of any description including any treatment there to and in any position provided as in roof padding, roof curb etc., complete all as specified and as directed.Note: -(a) Demolition should be done carefully to roof slab. (b) Any damage occurred in the roof surfaces during demolition shall be made good by the contractor without extra cost to the department.(c) Disposal of old debris/retrieved material to outside the premises or as directed |
| 2 | M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in roof padding laid in slope as per requirementmixed with integral water proofing liquid admixture as per manufacturer\"s instructions, complete all as specified and as directed.Note : (i) Minimum thickness of PCC shall be 50mm.(ii)Integral water proofing liquid admixture shallbe measured and paid separately underappropriate item here in after. |
| 3 | M&L for 15 mm thick rendering on fair faces of concrete surface incm 1:3 to be finished even and smooth with out suing extra cement under roof treatment mixed with water proofing compound (to be measured and paid seperately) |
| 4 | Supply only integral water proofing liquid admixture for concrete and mortar (Make :CONPLAST X421IC of Fosroc /SIKA No 1 of SIKA/equivalent brand of Pidilite), complete all as specified and directed. |
| 5 | M&L for water proofing treatment with APP based standard membranein roof with the following courses of treatment :-(a) Apply bituminous primer @ 0.40 Kg per sqm of the surface area including cleaning the surfaces completeall as specified.(MAKE : WP Shield Primer W of SIKA/Shalikote T-32 of STP/Equivalent brand of Tikidan Danosa.(b)Apply APP plastomeric bitumen based mineral finished water proofing membranepolyester reinforced(4 Kg/Sqm)overlaping minimum 75 mm in length side and 100 mm with side. including surface preparation before and after application of treatment as per manufactures instruction complete all as specified and as directed. (Make of APP Membrane: WP Shield 103 PM of SIKA/Super Thermolay 3mm (MT) of STP Limited/Equivalent brand of Tikidan Danosac complete all as specified |
| 6 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. |
| 7 | M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 and finishing even and smooth without using extra cement, complete all as specified and directed. |
| 8 | M&L for 15mm thick rendering on fair faces of brick work / stone masonry, concrete surface in cm 1:6 to be finished even and fair with out suing extra cement complete all as specified |
| 9 | M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces of ceiling in CM 1:3 and finishing even and smooth without using extra cement, complete all as specified and directed. |
| 10 | Preparation of new plastered surfaces of walls andapplying two coats of oil bound distemper over a coat of alkali resistant primer, complete all as specified and directed. |
| 11 | Preparation of newly plastered surfaces of ceilingand applying three coats of white wash, complete all as specified and directed. |
| 12 | M&L for applying two or more coats of 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces., complete all as specified and directed. |
| 13 | Complete removal of existing treatment of walls and applying 1mm thick wall care putty and prepare the smooth surface with sand paper and applying two coats of distemper oil emulsion paint, complete all as specified and directed. |
| 14 | M&L framed work as in doors / gates / Y Angle of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings conforming to Fe-410- W (GdeE-250) quality B (exclusive or steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, complete all as specified and directed. |
| 15 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 16 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n exc 4.0 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 17 | Taking down and refixing of shuttersin same openingafter easing and adjusting of any description exc 1 Sqm and n exc 2 Sqm each including resecuring/changing of builders hardware, complete all as specified and directed. |
| 18 | S&F for Pressed steel frame made out of mild steel 1.25mm thick sheet, with size of frame 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. and applying a shop coat of red oxide primer including providing PCC 1:3:6, type C-0 (using 12.5mm graded crushed stone aggregates) as in back filling of pressed steel frame, complete all as specified and directed. |
| 19 | S&F for Pressed steel frame made out of mild steel 1.25mm thick sheet, with size of frame 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. and applying a shop coat of red oxide primer including providing PCC 1:3:6, type C-0 (using 12.5mm graded crushed stone aggregates) as in back filling of pressed steel frame, complete all as specified and directed. |
| 20 | S&F 30mm thick 2nd class hardwood, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), complete all as specified and directed. |
| 21 | S&F 30mm thick 2nd class softwood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers, complete all as specified and directed. |
| 22 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying and fixing in opening, complete all as specified and directed. |
| 23 | S&F 30mm thick Factory made Solid panel PVC mouldeddoor shutter (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 24 | Prepartion of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 25 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay,complete all as specified and directed. |
| 26 | S&F factory made steel window with side hung shutter including Boxtype/projecting type hinges with steel handle, towerbolts 100 mm, steel peg stay, with glazing bars including applying one shop coat of red oxide primercomplete all as specified and directed |
| 27 | S&F factory made steel window with side hung shutter including Boxtype/projecting type hinges with steel handle,towerbolts 100 mm,steel peg stay, without glazing bars including applying one shop coat of red oxide primercomplete all as specified and directed |
| 28 | Preparation of new steel surface and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed. |
| 29 | S&F aluminium window and ventilator shutters powder coated of any colour (thickness or powder coating not less than 50 micron), side hung type without sash bars/ Sliding windows, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified and directed. |
| 30 | S&F Powder Coated aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc., complete all as specified and directed. |
| 31 | S&F 5.5mm thick Sheet glass, ordinary quality in squares exc 0.5 sqm each pane with solar control film 25 micron reflective type (gareware sun control or equivalent), complete all as specified and directed. |
| 32 | S&F 6mm thick PVC sheet decorative and white /colourfor aluminium doors, complete all as specified and directed. |
| 33 | S&F in repairs aluminium (die cast body) door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg, complete all as specified and directed. |
| 34 | S&F 3mm thick figured glass, pinheaded type ordinary quality and glazing with oil putty / wooden beading in squares not exceeding 0.50 Sqm, complete all as specified and directed. |
| 35 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 36 | S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 37 | S&F 125mm long medium weight, cold rolled mild steel Butt hinges, complete all as specified and directed.. |
| 38 | S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 39 | S&F 150mm size Aluminium anodised, handle of extruded section, fabricated type, anodised and fixed, complete all as specified and directed. |
| 40 | S&F 100mm size Aluminium anodised, handle of extruded section, fabricated type, anodised and fixed, complete all as specified and directed. |
| 41 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed. |
| 42 | S&F 300mm long, ordinary door springs including roller and roller plate, complete all as specified and directed. |
| 43 | S&F Gl frame work snap gridframemade out of angle section 22 x 22 mm on perimiter walls and tee section of 22 x 22 mm in web made to shape out of GI sheet work of size 605 x 605mm for seamless ceiling, and hangers 6 mm dia G.I. ( Upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. Flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long completeandincluding supply and fixing 8 mm thick Gypsum perforated particle board for insulation and accoustics purposes, 60cm x 60cm sizeas per manufacturers instructions and jointing and finishing to a flush finish of tapered and square edges other board any other joints with recommended jointing compound over jointing tapes including taking down existing ceiling, complete all as specified and directed. |
| 44 | S&F in repairs 20mm dia stainless steel drapery curtain rods including brackets, end finials (Latoo), for curtain rails fancy decorative type and fix with brass screws to walls approved quality etc., complete all as specified and directed. |
| 45 | S&Fin repairs drapery rod brackets both side and corner bulb nobs ae approve make, complete all as specified and as directed. |
| 46 | Demolition of old PQC / concrete of any description and in any position not other wise specifically provided for and demolished material thrown out ofpremises complete all as specified and directed by Engineer-in-Charge |
| 47 | M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 48 | M&L for 100mm thick plain cement concrete, 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in flooring , laid in alternate bays andfinishing the surface even and smooth without using extra cement, complete all as specified and as directed. |
| 49 | M&L for plain quality concrete work in pavement / hard standing of flexural strength 40 kg / Sqcm2 in field using 400 kg of cement per cubic metre or as per design mix whichever is higher using non circular synthetic polyster triangular fibre @ 0.25% by weight of cement, thickness of concrete 20 cm, complete all as specified and directed.Note:- (i) Unit rate quoted shall be inclussive steel formwork as required.(ii) Polyster triangular fibre shall be measured and paid as \"Supply only\" under respective Items of BOQ. |
| 50 | M&L for chequered cement concrete tiles size 300 mm x 300 mm x 22-25mm thick with grey cement and pigment , rubber moulded with laquer polish for extra shine, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 51 | M&L for 60mm thick machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006, M-35 with grey cement and pigment over and including 75mm thick PCC 1:4:8, type D-2 (Using 40mm graded crushed stone aggregate) and including 25mm thick compacted bed of fine sand and demolition of existing finishes, complete all as specified and direction. |
| 52 | M&L 75 mm thick, PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in plinth protection including cutting groveand using bitumen filler on jointfinished even and smooth without using extra cement, complete all as specified and directed. |
| 53 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed. |
| 54 | S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating, complete all as specified and directed. |
| 55 | S&F 0.63mm thick Galvanised, Plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating, complete all as specified and directed. |
| 56 | All as per Ser item No 54.00 here in before but except Sheets. |
| 57 | Dismantling of structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed. |
| 58 | M&L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W (Gde-E-250) quality-B,complete all as specified and as directed. |
| 59 | All as per Ser item No 58.00 here in before but erection and fixing only |
| 60 | S&F 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling existing water tank and removing from site, complete all as specified and directed. |
| 61 | S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling existing water tank and removing from site, complete all as specified and directed. |
| 62 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. |
| 63 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. |
| 64 | S&F for 15mm bore tubes, medium grade, galvanised, with all fitting, ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 65 | S&F for 20mm bore tubes, medium grade, galvanised, with all fitting, ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 66 | Refixing old GI pipe 15mm bore & connections in new or old position to walls and ceiling or laid in floor, complete all as specified and directed. |
| 67 | Refixing old GI pipe 20mm bore & connections in new or old position to walls and ceiling or laid in floor, complete all as specified and directed. |
| 68 | Cutting chases pining in brick, concrete walls built in cement mortar or cement lime mortar making good to facings where required and pointing in cement mortor 1:3to ends or edges of shelves lintels etc and cutting chases for concealed water tubing cutting exc 10cm but not exc 20cm girth, complete all as spcefied and directed |
| 69 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 70 | M&L for Glazed ceramic tile 450x300x06-7mm thick (coloured) on vertical surfaces such as wall, dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 71 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in skirting etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 72 | M&L for 10 to 12 mm thick vitrified parking tiles in approved shade from meteor series, area of each tile exceeding 0.08 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in matching coloured polymer cement based grout to match over and including 15 mm thick Screed bed or bedding layer in CM 1:6, complete all as specified and directed. |
| 73 | M&L for Light shade Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 74 | M&L for 20-25mm thick machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing / grinding and polishing upto mirror finish complete over and including 20mm thick screed bed in CM 1:6 and including demolition of existing stone slab and tiles, complete all as specified and directed. |
| 75 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed. |
| 76 | M&L for brick work with sub-class `B\" bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed. |
| 77 | Taking down the existing rolling shutters from the existing opening and refixing the same in position after carrying out necessary repairs including oiling, greasing,easing out etc size of shutter exc 7.00 Sqm & n exc 12.00 Sqm each. all as specified and directed |
| 78 | S&F in repairs 1.25mm thick of laths of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, push pull or manual type, complete all as specified and directed. |
| 79 | M&L for collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets including taking down old, complete all as specified and directed. |
| 80 | M&L for 25mm thick plain cement concrete, 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor finish even and rough to receive further floor finishes (tile/kota stone/ marble ), complete all as specified and directed. |
| 81 | S&F in repairs 15mm bore pillar tap, cast copper alloy quarter turn, chromium plated, fancy type, CP screwed down high pressure, complete all as specified and directed. |
| 82 | S&F in repairs 15mm bore Stop valve / angle valve, cast copper alloy, chromium plated, fancy type, screwed down high pressure with capstan head, complete all as specified and directed. |
| 83 | S&F in repairs 10 litre capacity PVC valveless, Syphonic action type, flushing cistern low level, white with inlet ball valve, float and handle including brackets and PVC flush pipe etc., complete all as specified and directed. |
| 84 | S&F in repairs Vitreous china squatting pan, Orissa pattern, size 580 x 440mm and making good, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., including trap set in and including concrete, complete all as specified and directed. |
| 85 | S&F in repairs vitreous china wash hand basin, white flat back, size of 550x400mm including cutting for and pinning in ends of brackets (including supply and fixing of brackets) or erecting stand, 32mm brass chromium plated waste fitting with long screwed shank and fly nut flangedend bedded in red led cement, chain and plug and porcelain stopper, complete all as specified and directed. |
| 86 | S&F in repair Vitreous China Urinal, Half stall type including all fittingswith grating and union for discharge pipecomplete including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and as directed |
| 87 | S&F in repairs looking mirror of size 600x450mm with PVC moulding,complete all as specified and directed. |
| 88 | S&F in repair 75mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp or laid in trenches, complete all as specified and as directed. |
| 89 | S&Fin repair 110mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp or laid in trenches, complete all as specified and as directed. |
| 90 | S&F 100/75mm outlet PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), complete all as specified and directed. |
| 91 | S&F 75mm size PVC (SWR) bends of any radius, complete all as specified. |
| 92 | S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. |
| 93 | S&F 110mm size PVC (SWR) bends of any radius, complete all as specified. |
| 94 | S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. |
| 95 | S & Fin repairs 110mm bore PVC (SWR) \"P’ trap complete all as specified and directedby |
| 96 | S&F 75mm bore PVC (SWR) vent cowl, complete all as specified and directed. |
| 97 | Deduction to be made from BOQ for Schedule \"A\" Part-II (Credit Schedule from dismantling / taking down items) worth Rs 1,15,540.00 during AOC. (Note :- Tenderers shall not quote for this Schedule) |
