Tender For Repair/ Replacement Of Modular Kitchen Accessories, Granite, Tiles And Other Connecting Works At Omq Area Under Ge (Af) Srinagar; 1 Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. 2 Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed. 3 M&L for brick work with sub-class `B bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed. 4 M&L for brick work with sub class B bricks (using old size bricks) straight or curved on plan to any radius in half brick thick wall radius, built in CM 1:4, complete all as specified and directed. 5 M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 and finishing even and smooth without using extra cement, complete all as specified and directed. 6 M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 and finishing even and smooth without using extra cement using integral water proofing compound, complete all as specified and directed. (WPC shall be measured and paid separately). 7 Supply only integral water proofing compound, complete all as specified and directed. 8 Preparation of new plastered surfaces of walls andapplying two coats of oil bound distemper over a coat of alkali resistant primer, complete all as specified and directed. 9 Preparation of new plastered surfaces of walls andapplying two coats of anti-fungal exterior emulsion paint (Apex) over a coat of cement primer including thin layer of wall care putty, complete all as specified and directed. 10 Complete removal of existing treatment of walls and applying 1mm thick wall care putty and prepare the smooth surface with sand paper and applying two coats of distemper oil emulsion paint, complete all as specified and directed. 11 Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n exc 4.0 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. 12 S&F pressed steel frame for doors with one rebates size of frame 105x60 mm including necessary fixing lungs hinges lock strike plate etc. including PCC, 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified and directed. 13 M&L for plain cement concrete, 1:2:4, Type B-1 (20mm graded crushed stone aggregate) as in hold fast blocks rungs etc. including necessary formwork, complete all as specified and directed. 14 S&F 35mm thick 2nd class hardwood plain framed, panelled shutter (two panel), factory made, with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed. 15 S&F 35mm thick 2nd class hardwood, factory made, glazed shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), complete all as specified and directed. 16 S&F 150mm size Aluminium handles, cast type, anodised, complete all as specified and directed. 17 S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed. 18 S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple & fixed clips of sheet, cast or extruded section & fixed bolts & sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed. 19 S&F in repairs 250mm mild steel helical door spring rat tail type including collar plate and welding if required or otherwise fixed with screw on wooden frames, complete all as specified and directed. 20 S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 in steel / wooden shutter of door & windows, complete all as specified and directed. 21 Preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. 22 Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed. 23 S&F GI frame work of size 605 x 605mm for seamless ceiling comprising of Gl perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 45 mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including supply and fixing 12mm thick Gypsum Board (water proof) fixed with screw or as per manufacturers instructions and jointing and finishing to a flush finish of tapered and square edges other board any other joints with recommended jointing compound over jointing tapes, finishing with one coat of primer and two coats of oil emulsion distemper over a coat 2mm thick wall care putty including taking down existing ceiling, complete all as specified and directed. 24 S&F in repairs solid PVC wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specifications,complete all as specified and directed. 25 S&F in repairs aluminium powder coated aluminium window having three track (minimum thickness of powder coating 50 micron) with aluminium section 92mm X 31.75mm (Weight bottom section 1.070 kg/m, top section 0.933 kg/m, shutter section 40mm X 18mm (weight of handle section 0.417 kg/m) interlock 0.547 kg/rm mounted on bearing to slide on tracks plain anodized in approved shade including supply andfixing of 5mm thick plain glass and wire mesh, PVC track gasket, EPDM rubber gasket on glass of weather tightening along with locks, handle including sealing gap with marble surfaces with silicon sealants making it water proof in all manner etc. complete all as specified and directed. 26 S&F Box type steel window double frame (glazed & gauged) made of ERW tube P- section of size 60mm x 25mm double rebated outer frame comprise glazed Skelton shutter door frame of ERW tube P-section size 50mm x 20mm with two Nos openable leaf consisting of two Nos of sash bar of T-sec 20mm x 3mm welded to frame with one No vertical mullion of ERW of ERW box type T-section size of 60mm x25mm FI 2mm thick welded / screwed to frame for fixing of wire gauge/glass and 10mm Sqr Bar security grill including fixture and fitting like as handle, tower bolt stopper , cleat, pintail hinges, holdfast primer etc. including taking down existing, complete all as specified and directed.(Note- sheet glass, wire mess will be measured and paid separately and window will be measured one side only) 27 S&F 3mm thick sheet glass ordinary quality and glazing with oil putty / wooden beading in squares not exceeding 0.50 Sqm, complete all as specified and directed. 28 S&F for powder coated aluminium grill (Thickness or powder coating not less than 50 micron) of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved powder coated aluminium standard section around the opening, complete all as specified and directed. 29 Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for, complete all as specified and directed. 30 Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finished surface, not exceeding 200m thick (Horizontal or sloping), complete all as specified and directed. 31 M&L for Reinforced cement concrete, 1:2:4, Type B-1 (using 20 mm graded crushed stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. 32 M&L for MS TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. 33 S&F in repairs 18-19mm thick block board, grade-2 quality, interior grade, commercial type, fixed with screws to timber framework as in kitchen drawers, cupboard shutters etc. complete all as specified and directed. 34 S&F 0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions, complete all as specified and directed. 35 S&F in repairs 100mm stainless steel, fancy type, round D drawer cabinet handles, including all fitting, complete all as specified and directed. 36 S&F in repairs 60mm size stainless steel hinge, self closing, Italian pattern suitable for wooden cabinet door opening / closing operation, complete all as specified and directed. 37 M&L for 3/4mm thick PVC edge lipping fixed with nails for 18/19 mm thick prelaminated particle board & shuttersetc., complete all as specified and directed. 38 S&F Magnet of suitable size fixed for cabin leafs, drawers etc., complete all as specified and directed. 39 S&F in repairs stainless steel telescopic channels roller of size25mm x 12mm,450mm length (when close) with male female rolling brackets suitable for baskets, complete all as specified and directed. 40 S&F in repairs Stainless steel 304 grade perforated cutlery basket of size 520mm width, 485mm depth and 100mm height, completeall as specified and directed. 41 S&Fin repairs Stainless steel 304 grade Cup & Saucer basket of size 520mm width, 485mm depth and 100mm height, complete all as specified and directed. 42 S&Fin repairs Stainless steel 304 grade designer Pull out detergent basket of size 100mm width, 485mm depth and 430mm height, complete all as specified and directed. 43 S&Fin repairs Stainless steel 304 grade designer pull out basket of size 810mm width, 485mm depth and 200mm height, complete all as specified and directed. 44 M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4 and including demolition of existing stone slab and tiles, complete all as specified and directed. 45 Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. 46 M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. 47 M&L for Glazed ceramic tile 300x600x06-7mm thick (coloured) on vertical surfaces such as wall, dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. 48 M&L for Light shade Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed. 49 M&L for Light shade Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in Skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat CM 1:4, complete all as specified and directed. 50 S&F in repairs sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm, complete all as specified and directed. 51 S&F in repairs Kitchen plate rack made of stainless steel 1mm thick with plugs washers as overall size of 900mm x 975mm including fixing to wall and all accessories, complete all as specified and directed. 52 Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. 53 Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. 54 S&F for 15mm bore tubes, medium grade, galvanised, with all fitting, ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. 55 S&F for 20mm bore tubes, medium grade, galvanised, with all fitting, ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. 56 Refixing old GI pipe 15mm bore & connections in new or old position to walls and ceiling or laid in floor, complete all as specified and directed. 57 Refixing old GI pipe 20mm bore & connections in new or old position to walls and ceiling or laid in floor, complete all as specified and directed. 58 M&L for Lagging to 20mm bore pipes used in external water supply or plumbing all around with 50mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25gauge 20mm mesh including applying with brushing neat cement slurry with 3 kg of cement per Sqm complete, complete all as specified and directed. 59 S&F in repairs 125mm dia CP grating doom with waste hole, complete all as specified and directed. 60 S&F in repairs 15mm size swan neck sink mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed. 61 S&F in repairs 15mm bore swan neck bib tap, cast copper alloy, chromium plated, fancy type, long body with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as specified and directed. 62 S&F in repairs 15mm bore stop valve / angle valve, cast copper alloy, two way, chromium plated, fancy type, long body with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as specified and directed. 63 S&F in repairs 15mm bore Stop valve / angle valve, cast copper alloy, chromium plated, fancy type, screwed down high pressure with capstan head, complete all as specified and directed. 64 S&F in repairs stainless steel soap dish fixed to wall with plug and screw, complete all as specified and directed. 65 S&F in repairs 50mm dia PVC pipe low density (LDPE) of pressure 6kg/Sqcm fixed to wall or laid in floor as waste pipe, complete all as specified and directed. 66 S&F in repairs 15mm size PVC connections with PTMT nuts of length 600mm, complete all as specified and directed. 67 S&F in repairs 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, floor, trenches, complete all as specified and directed . 68 S&F in repairs 100/75mm outlet PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), complete all as specified and directed. 69 S&F 75mm size PVC (SWR) bends of any radius fitted with oval access doors, complete all as specified. 70 S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. 71 S&F 75mm bore PVC (SWR)junction single, (Double T) equal or unequal, complete all as specified and directed. 72 M&L for plain cement concrete, 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in surface channel, coping, drain and RCC post etc. including necessary form work, complete all as specified and as directed. 73 Deduction to be made from BOQ for Schedule A Part-II (Credit Schedule from dismantling / taking down items) worth Rs 90,015.00 during AOC. (Note :- Tenderers shall not quote for this Schedule)
