Tender For Composite Civil Works In Plant Area At Gail Vijaipur; 1 Surface Dressing:Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, All kinds of soil as directed by Engineer-in- Charge. 2 Earth work in excavation upto 1.5 m:Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation, trenches, drains including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil within GAIL premises or as directed by EIC, including all leads & lifts. Earth/ disposed soil to be levelled & neatly dressed. All kind of soil including soft/ordinary rock at depth upto 1.5 m. 3 Extra for Earth work in excavation below 1.5 m:Extra for every additional lift of 1.5m or part thereof in excavation / banking excavated or stacked material. All kind of soil including soft/ordinary rock at depth upto 6m. 4 PCC 1:2:4:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -at all level & depth :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 5 RCC M-25:Providing and laying in position site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the Concrete of M25 grade with minimum cement content of 330 kg /cum. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cementcontent, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement for all type of work and at all level. 6 Filling available excavated:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering. 7 Demolishing work:Demolishing cement concrete/RCC/bitumen/brickwork/precast/tiles (floor/wall), manually/ by mechanical means including stacking of steel bars along with disposal of unseviceable material within GAIL plant premises as per direction of Engineer - in- charge. 8 Steel reinforcement:Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. 9 Structural steel work:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete 10 Precoated GI sheet:Providing and fixing colour coated precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 11 Centering and shuttering:Centering and shuttering including strutting, propping etc. and removal of formwork for foundations, footings, bases of columns, beams etc. as per direction of Engineer-in-charge. 12 Brick work:Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) 13 Plaster 6mm:6mm cement plaster of mix 1:3 (1 cement: 3 fine sand)as per direction of EIC. 14 Plaster 12mm:12mm cement plaster of mix 1:4 (1 cement: 4 fine sand) as per direction of EIC. 15 Plaster 18mm:18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). 16 M.S. Wire mesh (rabbit) :Providing and fixing M.S. Wire mesh (rabbit) 17 Wall tiles :Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size (min. size 300*450 mm) as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete 18 Vitrified floor tiles :Providing and laying glazed vitrified floor tiles of polished/matt finish in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm 19 Acid resistant Wall tiles :Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In wall/dado/skirting on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile 20 Acid resistant floor tiles :Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile 21 Granite stone with moulding:Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm 22 Kota stone with moulding:Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and moulding complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 23 WPC Door Chaukhat:Providing factory made single extruded WPC (Wood Polymer Composite) solid door/window, clerestory windows & other Frames/Chowkhat and screwed with full body threaded star headed SS screws of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-InCharge. of required size. 24 PVC Door shutter:Providing Factory made PVC rigid foam panelled shutter along with necessary screws, hinges and required fittings as per approved brand, complete as per directions of EIC. 25 Flush door shutters:Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 26 Paver block 80 mm:Providing and laying factory made Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. 27 Sliding Door bolt (Aldrop):Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 250x16 mm 28 Tower bolts:Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm 29 Handles:Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm 30 Water proofing:Supplying and applying of waterproofing on terrace/ roof including surface preparation prior to waterproofing application as per detailed technical specification. Providing and applying one coat of PU/Epoxy based primer of approved make (Asian Paint Smart Care/Berger Home Shield/Nerolac Perma) as per product specification. After that, Providing and applying first coat of PU based waterproofing liquid membrane of approved make (Asian Paint Smart Care/Berger Home Shield/Nerolac Perma) as per product specification. After that, Providing and fixing of corner joint tape of approved make (Asian Paint /Berger/Nerolac Perma) as per product specification.After that, Providing and applying second coat of PU based waterproofing liquid membrane of approved make (Asian Paint Smart Care/Berger Home Shield/Nerolac Perma) perpendicular to first coat as per productspecification.Note: All the above-mentioned products must be of same make. E.g. Primer+ Waterproofing coat must be of same brand. 31 Plaster drip groove:Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 32 Plaster of paris putty:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over plastered surface, for application on interior/exterior on existing surface or uneven surface to prepare the surface even and smooth complete as per direction of EIC.MAKE: Birla, JK, Saint Gobain, ASIAN, BERGER. DULUX, NEROLAC, INDIGO or as per direction of EIC. 33 Primer:Providing & Applying priming coats of exterior/Interior grade on old / new exterior /interior surface, one or more coat as per manufacture company specification or as per direction of EIC. All materials , labour, tools and tackles, Taxes & duties, loading & unloading transportation complete as per direction of EIC. MAKE: ASIAN, BERGER. DULUX, NEROLAC, INDIGO or as per direction of EIC. 34 Acrylic emulsion paint (Internal):Painting with premium acrylic emulsion paint of interior grade of required colour and of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour (one or more coat) on old / new surface as per manufacture company specification or as per direction of EIC. All materials , labour, tools and tackles, Taxes & duties, loading & unloading transportation complete as per direction of EIC.MAKE: ASIAN (Apcolite Premium Emulsion), BERGER (Rangoli Total Care), NEROLAC (Beauty Gold) or as per direction of EIC. 35 Acrylic emulsion paint (External ):Painting with premium acrylic amooth exterior paint weather proof, fungal resistant, dust resistant of required colour and of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour (one or more coat) on old / new surface as per manufacture company specification or as per direction of EIC. All materials , labour, tools and tackles, Taxes & duties, loading & unloading transportation complete as per direction of EIC.MAKE: ASIAN (Apex Ultima), BERGER (Weathercoat All Guard), NEROLAC (Excel Total) or as per direction of EIC. 36 Epoxy Paint on floor:Finishing with Epoxy paint (two or more coats) of required colour and of approved brand and manufacture at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work as per direction of EIC. MAKE: ASIAN, BERGER, NEROLAC or as per direction of EIC. 37 Khurras:Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 38 Door closer:Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body,with necessary accessories and screws etc. complete. 39 Door stopper:Providing and fixing aluminium hanging floor door Twin rubber stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 40 P&F decorative laminated sheet:Providing & Fixing decorative laminated sheet 1.0 mm thick of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conformingto IS : 2046 Type S, including cost of adhesive of approved quality. 41 Sand filling:Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 42 Aluminium frame work:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)Powder coated aluminium 43 Weather silicon sealant:Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width 44 False Ceiling:Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections consisting of main T runner with suitably spaced joints to get required length, spaced at 1200 mm center to center and cross T, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. all complete for all heights as per specifications, drawings including removing of existing false ceiling with supported frame from site and shifting to defined location within GAIL premises and as directed by Engineer-in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet electro statically polyester powder coated, including factory painted after bending. 45 MS sheet door:1mm thick M.S. sheet door-Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. 46 Synthetic enamel:Painting with synthetic enamel paint of approved brand & manufacture of required colour to give an even shade: (one or more coat) on old / new surface as per manufacture company specification or as per direction of EIC. All materials , labour, tools and tackles, Taxes & duties, loading & unloading transportation complete as per direction of EIC. MAKE: ASIAN (Apcolite Premium Gloss Enamel), BERGER (Luxol High Gloss Enamel), DULUX, NEROLAC (Synthetic Hi-Gloss Enamel), INDIGO or as per direction of EIC. 47 TOUGHENED GLASS 6 MM :Providing & Fixing Toughened glass 6 mm thickness of required shape and size as per approved brand, complete as per directions of EIC. Make : Saint Gobain , Modiguard. 48 Shoring:Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered): 49 JCB / HYDRAULIC EXCAVATOR:Hire - charges include cost of services of operating staff, Cost of lubricating oil, diesel / Petrol/ Kerosene oil , other consumables for running the plant and machinery. The hire charges of plant machinery on per day basis are for single shift of eight working hours. 50 Tractor with trolley:Hire - charges include cost of services of operating staff, Cost of lubricating oil, diesel / Petrol/ Kerosene oil , other consumables for running the plant and machinery. The hire charges of plant machinery on per day basis are for single shift of eight working hours. 51 Kerb Stones:Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). 52 Wood work:Providing and fixing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length. Second class teak wood 53 Beading:Providing and fixing 2nd class teak wood moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board/flush door/wood as per direction of Engineer-in-charge. 54 Welding in existing PPG:Removal of old damaged Polypropylene welding and providing of fresh new welding in existing Polypropylene glass lining with PP strips and double sealing of welding joints with 5MM Welding Rod All material should contain 2% Carbon black and UV stablizer 55 P&F PPG Lining 3.5 mm th.:Testing of existing PPG sheet to identify debounded sheet and damaged lining area, Removal of existing damaged Polypropylene glass lining/FRP, Providing and fixing of 3.5MM thick Polypropylene Glass lining, where as polypropylene sheet will be of 2MM thick with U.V. stabilization, and approx 1.5MM thick adhesive backing of FRP lamination with 450 GSM chopped stand mat and resin, Resin ratio in FRP lamination should not be less than 2.0 KG / m2, Resin make :: Mechamco / Crest or equalant . PPGL sheet should contain 2% Carbon Black and UV stablized Make Sangir Plastics/ Mandhana Polymers 56 P&F FRP Lining:Removal of existing Polypropylene glass lining/FRP, providing and fixing of fresh 5MM thick FRP Lining by vinyl ester and super vinyl ester resin with 300 GSM and 450GSM chopped strand mat and Resin, Resin make should be either of Mechamco / Crest or equivalant. 57 Fire proofing old work:Providing and applying vermiculite cementious (fendolite M II or equivalent) coating as fire proofing material around structural steel members along with surface preparation, reinforcement/mesh support systems, curing compounds, water shed sealing at terminating edges, scaffolding/form work, testing etc. with minimum fire ratings and thickness as mentioned in Technical Specifications including dismantling of existing fireproofing, all equipments, manpower, tools, tackles, and disposal of dismantled material at designated place etc. complete as per detailed scope of work, SCC and Technical specifications as mentioned in Tender document and as directed by Engineer in charge. 58 Fire proofing new work:Providing and applying vermiculite cementious (fendolite M II or equivalent) coating as fire proofing material around structural steel members along with surface preparation, reinforcement/mesh support systems, curing compounds, water shed sealing at terminating edges, scaffolding/form work, testing etc. with minimum fire ratings and thickness as mentioned in Technical Specifications including all equipments, manpower, tools, tackles etc. complete as per detailed scope of work, SCC and Technical specifications as mentioned in Tender document and as directed by Engineer in charge. 59 Stainless steel:Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc.,including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 60 Hand Dryer:Providing and Fixing automatic NO-Touch electric hand-driers complete with all accessories & fittings. 61 Anti Temite Treatment:Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 62 PLUMBING WORKS: PVC pipes 75 mm:Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter 63 PLUMBING WORKS: PVC pipes 110 mm:Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter 64 PLUMBING WORKS: CPVC pipes 20 mm:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal dia Pipes 65 PLUMBING WORKS: CPVC pipes 25 mm:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the wallsetc.25 mm nominal dia Pipes 66 PLUMBING WORKS: Indian type W.C:Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 67 PLUMBING WORKS: European type W.C.:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) W.C. pan with ISI marked white solid plastic seat and lid, with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required as per direction of EICMake: Johnson, Hindware, Parryware, Jaquar. 68 PLUMBING WORKS: Wash basin:Providing oval shape wash basin (white/ off-white) of size 560x450mm or as per existing requirement/ companys manufacture as per approved brand, complete as per directions of EIC. 69 PLUMBING WORKS: Urinal basin :Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with automatic push tap as directed by EIC. 70 PLUMBING WORKS: PVC connection pipe:Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length , 15 mm nominal bore 71 PLUMBING WORKS: C.P. bib cock:Providing and fixing CP bib cock for wash basin as per approved Brand: Hind ware, Johnson, Parry ware, Jaguar or equivalent complete or as per directions of EIC 72 PLUMBING WORKS: Water Tank:Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 73 PLUMBING WORKS: Liquid Soap Container:Providing and fixing PTMT Liquid Soap Container of 400 ml capacity, standard shape with bracket of the same materials with snap fittings of approved quality and colour 74 PLUMBING WORKS: Mirror:Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 75 PLUMBING WORKS: PTMT Towel Rail 600mm:Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms 76 PLUMBING WORKS: Bottle Trap:Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. 77 PLUMBING WORKS: PTMT Grating 100 mm:Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid, having 150 mm nominal size square, 100 mm diameter of the inner hinged round grating 78 PLUMBING WORKS: S.W. gully trap:Providing and fixing S.W. gully trap P type 150x100 mm 79 PLUMBING WORKS: C.I. Rectangular cover:Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg 80 PLUMBING WORKS: C.I. cover and frame:Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg 81 PLUMBING WORKS: Angle valve :Providing and fixing C.P. Brass angle valve 15 mm nominal bore 82 PLUMBING WORKS: Pressmatic auto closing wash basin Pillar cock:Providing C.P. push type pillar cock for wash basin with pressmatic auto closing system as per approved brand, complete as per directions of EIC. Brand : Johnson model no. PRS 031, Hindware, Parryware, Jaguar or equivalent 83 PLUMBING WORKS: C.P HEALTH FAUCET:Providing C.P. health faucet with 8mm dia 1m long flexible tube & wall hook with all necessary fittings and accessories as per approved brand, complete as per directions of EIC. Brand : Hindware, Johnson, Parryware, Jaguar or equivalent 84 ELECTRICAL 85 Fresh air exhaust:Providing and Fixing Fresh air exhaust fan 300 mm with louvers 86 Flameproof Exhaust Fan:EXHAUST FAN, FLAME PROOF, 450 MM HEAVY DUTY INDUSTRIAL FLAME PROOF (EX-D) EXHAUST FAN 450 MM SWEEP DIA,1440 RPM COMPLETE WITH LOUVERS ALL REQUIRED ACCESSORRIES SUITABLE FOR APPLICATION IN GAS GROUPIIC PLEASE SUPPLY THE MATERIAL WITH FOLLOWING SPECIFICATIONS: FLAMEPROOF EXHAUST FAN, IMPELLER SIZE 18, SINGLE PHASE, 230-250V AC, CFM 4000, Ex-d, GAS Gr. IIA, IIB, IIC, IP-66, ZONE-1, 2, T6, DIE CAST ALUMINIUM/LIGHT METAL BODY, WITH GLAND AND LOUVRES ALONG WITH TEST CERTIFICATE. 87 4 Ft. 22W LED Tube Lights:LED TUBE 4FT 22 W 110-280 V RETROFIT TYPE 88 Flexible Copper Wire (Red,Black, Green):WIRE,CU,1Cx2.5MM2,BLACK,PVC INS COLOUR: BLACK, FLEXIBLE CROSS SECTION: 2.5 MM2 Voltage : 1100V Number of Cable Strands : Multi Strand Conduction Material : Copper as per Class-2 of IS: 8130 Flame Retardant Low Smoke Cable. ISI Marked. Recommended make - Polycab India Limited, Havells India Limited, Finolex Cables Limited, Prime Cable Industries Pvt. Ltd, KEI Industries Limited, Torrent Cables Limited, Universal Cables Limited. 89 Switch & Socket :SWITCH,SP,6A,W16401A,ANCHOR CODE-W16401ACURRENT: 6A POLE: ONE , 240 V, 6 A ,ISI Marked, 1 Way Switch to IS:3854/1997 with latest amendments 90 Ceiling Fan 1200 mm sweep size (52 W):CEILING FAN,1200MM,230V,ORIENT,3 BLADE CEILING FAN,1200MM,230V## MAKE: ORIENT, 3 BLADE## 91 Flameproof IIC group Lights 45 watt:LED FIXTURE 45W,T6,EXD,IIC,WELL GLASS LED FIXTURE,45WATT, WELL GLASS FIXTURE, SINGLE PHASE AC FLAMEPROOF,EX-D, GAS GROUP:IIC, TEMP CLASS:T6 IP:66 CLASS:A,TOUGHENED GLASS WITH STAINLESS STEEL WIRE MESH PROTECTION 92 Flexible armoured Cable 3CX2.5 Sqmm:Flexible armoured Cable 3CX2.5 Sqmm 93 Switch & socket outside Battery Room:SWITCH,SP,6A,W16401A,ANCHOR CODE-W16401A CURRENT: 6A POLE: ONE WAY: ONE CURRENT: 6A POLE: ONE WAY: ONE ISI Marked, 6A, 1 Way ,Bell Push Switch to IS:3854/1997 with latest amendments Rated Voltage (Volt) 230 Volt 94 FLP SWITCH&SOCKET,IIC, 16A,3P,230/24V:FLAMEPROOF PLUG & SOKET, COMPLETE CURRENT: 16A,3 PIN, ZONE 1 & 2 GROUP:IIC ONE NO. OUTLET WITH STEP DOWNTRANSFORMER (230/24V) INPUT:230V,OUTPUT: 24V MATERIAL: DIE CASTALUMINIUM ALLOY CABLE ENTRY 2X3/4 INCHET WITH ONE NO. 3/4 INCH ET FLP DOUBLE COMPRESSION CABLE GLAND AND ONENO.PLUG OF SS/BRASS NICKLE PLATED.
