|
| 1 | Material and labour for preparation of old painted external steel surfaces of filtration plant of size 2600mm dia and 3100mm length and applying two coats of anti-corrosive bituminous epoxy paint including complete removal of existing treatment by scrapping the surfaces with wire brush, de-scaling etc., at NORA and MRS complete all as specified and as directed. |
| 2 | M&L for preparation of old plastered/painted surfaces and applying one coat of primer followed by two coats of weather-proof exterior grade acrylic emulsion paint (tint to match existing pattern) on RCC OHT walls up to 25 m height, including necessary scaffolding, staging and safety measures, complete all as specified and directed. |
| 3 | M&L for preparation of old plastered/painted surfaces and applying one coat of primer followed by two coats of weather-proof exterior grade acrylic emulsion paint (tint to match existing pattern) on RCC OHT walls up to 23 m height, including necessary scaffolding, staging and safety measures, complete all as specified and directed. |
| 4 | M&L for cleaning of overhead tank of capacity 1 Lakh gallons at a height of 24.3m with dewatering the sump, removing the deposited mud from the overhead tank and washing with bleaching powder including writing of capacity of tank and synthetic enamel paint of white tint over black base complete all as specified and directed by Engineer-in-charge. Note: (Cleaning of the tank must be performed with all necessary measures for safety of working person) |
| 5 | All as per item No. 04 here-in-before but capacity of 0.5 Lakh gallons at a height of 22.8 m |
| 6 | M&L for cleaning of RCC tank of capacity 1 Lakh Ltr with dewatering the tank, removing the deposited mud from the RCC tank and washing with bleaching powder including writing of capacity of tank and synthetic enamel paint of white tint over black base complete all as specified and directed by Engineer-in-charge. Note: (Cleaning of the tank must be performed with all necessary measures for safety of working person) |
| 7 | M&L for cleaning of RCC underground sump of capacity 2.25 lakh gallons, dewatering the sump with water lifting pump, descaling internal surfaces of underground sump with wire brush, removing the deposited mud from inside the sump, washing with bleaching powder and flush water two times and dewatering, applying two coats of lime wash inside the sump including writing capacity of tank, date of cleaning with synthetic enamel paint of white tint over black base (size of letter 5mm wide and 15cm in height) complete all as specified and as directed by the Engineer-in-charge. |
| 8 | M&L for cleaning of Static water tank (SWT) of capacity 0.5 lakh gallons, dewatering the SWT with water lifting pump, descaling internal surfaces of SWT with wire brush, removing the deposited mud from inside the SWT, washing with bleaching powder and flush water two times and dewatering, applying two coats of lime wash inside the SWT including writing capacity of SWT, date of cleaning with synthetic enamel paint of white tint over black base (size of letter 5mm wide and 15cm in height), water level marking inside the SWT and painting the steel mesh and channels of the SWT cover complete all as specified and as directed by the Engineer-in-charge. |
| 9 | M&L for cleaning of Static water tank (SWT) of capacity 0.25 lakh gallons, dewatering the SWT with water lifting pump, descaling internal surfaces of SWT with wire brush, removing the deposited mud from inside the SWT, washing with bleaching powder and flush water two times and dewatering, applying two coats of lime wash inside the SWT including writing capacity of SWT, date of cleaning with synthetic enamel paint of white tint over black base (size of letter 5mm wide and 15cm in height), water level marking inside the SWT and painting the steel mesh and channels of the SWT cover complete all as specified and as directed by the Engineer-in-charge. |
| 10 | Supply and fix cross arms, bracings, support clamps etc made out of mild steel channel or angle section or MS sheet or square bar of required size and shape including door type hinges, door handle, clamp back plate with bolt nuts & washers drilledwelding bending cold or hot in any shape or size painted with two coats of aluminium paint over a coat of red oxide primer complete all as specified and as directed. |
| 11 | Material and labour for PCC 1:3:6 type C-1 (Using 20mm graded stone aggregate) as foundation for GI pipe base complete all as specified and as directed. |
| 12 | Material and labour for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar of 1:6 along with whitewashing on PCC surface with two coat complete all as specified and directed |
| 13 | Demolition of Concrete of any description and in any position not otherwise specifically provided for and removing debris outside MD Land complete all as specified and directed. |
| 14 | M&L 75mm thick PCC type C-2, 1:3:6 (40mm graded stone aggregate) as in path, hard standing, parking floors, etc., complete all as specified and directed. |
| 15 | Demolition of stone tiles/slabs of any description or thickness in floors, aprons etc., laidbedded and pointed in any mortar complete all as specified and directed. |
| 16 | M&L coloured chequered cement concrete tiles 300 x 300mm x 25mm thick set, jointed and pointed in neat slurry in floors with grey cement and pigments over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in cement plaster 1:4 complete all as specified and as directed. |
| 17 | Excavation in trenchesnot exceeding 1.5mtr wide & notexceeding 1.5 mtr deep getting out in soft /loose soil for taking up/laying CI/GI pipe all as specified and directed by Engr-in-charge. |
| 18 | Returning , filling in trenches (Soft/Loose soil) in layers not exceeding 25 cm thick after laying of pipe including spreading, levelling & well ramming including watering as required all as specified and directed by Engr-in-charge. |
| 19 | Removing surplus excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above from the starting point all as specified and directed by Engr-in-charge. |
| 20 | Supply and lay in repiars DI pipe K-7 with flanged / spigot ends (as per the site requirement), centrifugally cast suitable for and including necessary flanges, nut and bolts of 150mm dia size complete all as specified and as directed. |
| 21 | M&L for run lead joint for spigot and socket pipes and fittings of size150 mm dia complete all as specified and as directed. |
| 22 | Material and labour for bends (any radius and angle) tappers any type (straight, bend, increasing, decreasing or double socket) Tee, pieces, single branch, “ Y” junction, double branch, cross (all socket or socket spigot) collars, caps, caps and plugs suitable for CI / DI pipe upto 300mm bore complete all as specified and as directed. |
| 23 | M & L for white washing of inner and outer surfaces of valve chamber of any size including preparation of surfaces, applying two coats of white wash on walls and ceiling in case of PCC cover or one coat of red oxide primer and one coat of synthetic enamel black paint in case of metal cover of valve chamber complete all as specified and directed by Engineer-in-Charge. |
| 24 | M & L for painting of sluice valve of any size from 80 mm to 300 mm dia, including preparation of surface by cleaning, scraping off rust/loose paint, applying one coat of synthetic enamel black paint on the entire valve body, and painting the wheel/handwheel in red synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material and labour for painting on steel surface with synthetic enamel paint two coat over a coat of red oxide incl necessary preparation of new steel surface complete all as specified and directed by Engineer-in-Charge. |
| 26 | Taking down existing pump set (monoblock / non‑clog self‑priming / centrifugal) of following capacity by disconnecting all electrical and mechanical connections; dismantling pump and motor assembly; cleaning, inspecting, and replacing unserviceable gaskets, fasteners, and consumables; lubricating bearings; reassembling, aligning, reconnecting suction and delivery pipelines; making electrical connections; testing and commissioning to ensure smooth operation, complete all as specified and directed.Note: Replacement of any major itemswill be measured and paid for separately. |
| 27 | a) 0.5 to 2 HP |
| 28 | b) 5 to 7.5 HP |
| 29 | c) 10 HP |
| 30 | d) 15 HP |
| 31 | e) 20 HP |
| 32 | f) 40 HP |
| 33 | Material and labour for rewinding of monoblock / non‑clog self‑priming / centrifugal pump motor of following capacity, including removal of burnt‑out winding, cleaning stator slots, providing new super‑enamelled copper winding wire of suitable gauge, inserting insulation materials, varnishing with Class F/H insulating varnish, oven baking, assembling motor with new gaskets and fasteners, testing insulation resistance and performance, reconnecting and commissioning, complete all as specified and directed. |
| 34 | a) 0.5 to 2 HP |
| 35 | b) 5 to 7.5 HP |
| 36 | c) 10 HP |
| 37 | d) 15 HP |
| 38 | e) 20 HP |
| 39 | f) 40 HP |
| 40 | Supply only deep groove ball bearings for drive-end and non-drive-end of monoblock / non-clog self-priming / centrifugal pump motor of following capacity, complete all as specified and directed. |
| 41 | a) 0.5 to 2 HP |
| 42 | b) 5 to 7.5 HP |
| 43 | c) 10 HP |
| 44 | d) 15 HP |
| 45 | e) 20 HP |
| 46 | f) 40 HP |
| 47 | Supply only mechanical seal assembly suitable for monoblock / non-clog self-priming / centrifugal pump of following capacity, complete all as specified and directed. |
| 48 | a) 0.5 to 2 HP |
| 49 | b) 5 to 7.5 HP |
| 50 | c) 10 HP |
| 51 | d) 15 HP |
| 52 | e) 20 HP |
| 53 | f) 40 HP |
| 54 | Supply only dynamically balanced bronze/stainless-steel impeller suitable for monoblock / non-clog self-priming / centrifugal pump of following capacity, complete all as specified and directed. |
| 55 | a) 0.5 to 2 HP |
| 56 | b) 5 to 7.5 HP |
| 57 | c) 10 HP |
| 58 | d) 15 HP |
| 59 | e) 20 HP |
| 60 | f) 40 HP |
| 61 | Supply only thrust pads and bushes suitable for monoblock / non-clog self-priming / centrifugal pump of following capacity, complete all as specified and directed. |
| 62 | a) 0.5 to 2 HP |
| 63 | b) 5 to 7.5 HP |
| 64 | c) 10 HP |
| 65 | d) 15 HP |
| 66 | e) 20 HP |
| 67 | f) 40 HP |
| 68 | Supply only machined stainless steel shaft suitable formonoblock / non-clog self-priming / centrifugal pump of following capacity, complete all as specified and directed. |
| 69 | a) 0.5 to 2 HP |
| 70 | b) 5 to 7.5 HP |
| 71 | c) 10 HP |
| 72 | d) 15 HP |
| 73 | e) 20 HP |
| 74 | f) 40 HP |
| 75 | Taking down existing jet pump set of following capacity by disconnecting all electrical and mechanical connections; dismantling pump and motor assembly; cleaning, inspecting, and replacing unserviceable gaskets, fasteners, and other minor consumables; lubricating bearings; reassembling, aligning, reconnecting suction and delivery pipelines; making electrical connections; testing and commissioning to ensure smooth operation, complete all as specified and directed.Note: Replacement of any major items will be measured and paid for separately. |
| 76 | a) 1 HP |
| 77 | b) 2 HP |
| 78 | Material and labour for rewinding of jet pump motor of following capacity by carefully removing burnt-out winding; cleaning stator core; supplying and winding with super-enamelled copper wire of suitable gauge; inserting proper insulation materials; varnishing and oven-baking; reassembling motor; replacing worn-out bearings, bushes, and gaskets as required (measured and paid separately); testing and commissioning to ensure smooth and proper operation, complete all as specified and directed. |
| 79 | a) 1 HP |
| 80 | b) 2 HP |
| 81 | Supply only deep groove ball bearings for drive-end and non-drive-end of jet pump motor of following capacity, complete all as specified and directed. |
| 82 | a) 1 HP |
| 83 | b) 2 HP |
| 84 | Supply only mechanical seal assembly suitable for jet pump of following capacity, complete all as specified and directed. |
| 85 | a) 1 HP |
| 86 | b) 2 HP |
| 87 | Supply only dynamically balanced bronze/stainless-steel impeller suitable for jet pump of following capacity, complete all as specified and directed. . |
| 88 | a) 1 HP |
| 89 | b) 2 HP |
| 90 | Supply only thrust pads and bushes suitable for jet pump of following capacity, complete all as specified and directed. . |
| 91 | a) 1 HP |
| 92 | b) 2 HP |
| 93 | Supply only precision-machined stainless steel shaft suitable for jet pump of following capacity, complete all as specified and directed. . |
| 94 | a) 1 HP |
| 95 | b) 2 HP |
| 96 | Taking down existing pump set by disconnecting electrical and mechanical connections, lifting open‑well submersible pump set of following capacity, from well/pit; cleaning and inspecting pump and motor; replacing worn‑out gaskets, nuts, bolts, and fasteners as required; lowering the pump back into position; reconnecting suction and delivery pipelines; aligning motor; making electrical connections; testing and commissioning for smooth operation, complete all as specified and directed.Note: Replacement of any major itemswill be measured and paid for separately. |
| 97 | a) 0.5 to 3 HP |
| 98 | b) 5 HP |
| 99 | c) 7.5 HP |
| 100 | Material and labour for rewinding of open-well submersible motor of following capacity, including removing burnt-out winding, cleaning stator slots, providing new super-enamelled copper wire of suitable gauge, inserting insulation materials such as slot liners, wedges, and varnishing with Class F/H insulating varnish, baking in oven for proper curing, assembling motor with new gaskets and fasteners, testing insulation resistance and no-load performance, lowering motor in position, reconnecting to supply, and commissioning for satisfactory operation, complete all as specified and directed. . |
| 101 | a) 0.5 to 3 HP |
| 102 | b) 5 HP |
| 103 | c) 7.5 HP |
| 104 | Supply only deep groove ball bearings (drive end and non‑drive end) suitable for open‑well submersible motor of following capacity, complete all as specified and directed. . |
| 105 | a) 0.5 to 3 HP |
| 106 | b) 5 HP |
| 107 | c) 7.5 HP |
| 108 | Supply only mechanical seal assembly of appropriate size and make for open‑well submersible pump following capacity complete all as specified and directed. . |
| 109 | a) 0.5 to 3 HP |
| 110 | b) 5 HP |
| 111 | c) 7.5 HP |
| 112 | Supply only bronze/stainless steel impeller, dynamically balanced, suitable for open‑well submersible pump of following capacity, complete all as specified and directed. . |
| 113 | a) 0.5 to 3 HP |
| 114 | b) 5 HP |
| 115 | c) 7.5 HP |
| 116 | Supply only thrust pads and bushes suitable for open‑well submersible pump of following capacity, complete all as specified and directed. . |
| 117 | a) 0.5 to 3 HP |
| 118 | b) 5 HP |
| 119 | c) 7.5 HP |
| 120 | Supply only dynamically balanced stainless steel shaft suitable for open‑well submersible pump of following capacity, complete all as specified and directed. . |
| 121 | a) 0.5 to 3 HP |
| 122 | b) 5 HP |
| 123 | c) 7.5 HP |
| 124 | Taking down existing multi‑stage submersible pump set of following capacity by disconnecting all electrical and mechanical connections; lifting from well/pit using lifting arrangement; dismantling pump and motor assembly; cleaning, inspecting, and replacing unserviceable gaskets, fasteners, and minor consumables; lubricating bearings; reassembling, lowering back into position; reconnecting suction and delivery pipelines; making electrical connections; testing and commissioning for smooth operation, complete all as specified and directed.Note: Replacement of any major items will be measured and paid for separately. |
| 125 | a) 1 to 3 HP |
| 126 | b) 5 to 7.5 HP |
| 127 | c) 10 HP |
| 128 | d) 15 HP |
| 129 | e) 17.5 HP |
| 130 | f) 20 HP |
| 131 | Material and labour for rewinding of multi‑stage submersible pump motor of following capacity by carefully removing burnt‑out winding; cleaning stator core; supplying and rewinding with super‑enamelled copper wire of correct gauge; inserting proper insulation materials; varnishing and oven‑baking; reassembling motor; replacing worn‑out bearings, bushes, and gaskets as required (measured and paid separately); testing and commissioning to ensure smooth and proper operation, complete all as specified and directed. . |
| 132 | a) 1 to 3 HP |
| 133 | b) 5 to 7.5 HP |
| 134 | c) 10 HP |
| 135 | d) 15 HP |
| 136 | e) 17.5 HP |
| 137 | f) 20 HP |
| 138 | Supply only deep‑groove ball bearings (drive end and non‑drive end) suitable for multi‑stage submersible pump motor of following capacity, complete all as specified and directed. . |
| 139 | a) 1 to 3 HP |
| 140 | b) 5 to 7.5 HP |
| 141 | c) 10 HP |
| 142 | d) 15 HP |
| 143 | e) 17.5 HP |
| 144 | f) 20 HP |
| 145 | Supply only mechanical seal assembly suitable for multi‑stage submersible pump of following capacity, complete all as specified and directed. . |
| 146 | a) 1 to 3 HP |
| 147 | b) 5 to 7.5 HP |
| 148 | c) 10 HP |
| 149 | d) 15 HP |
| 150 | e) 17.5 HP |
| 151 | f) 20 HP |
| 152 | Supply only dynamically balanced bronze/stainless steel impeller suitable for multi‑stage submersible pump of following capacity, complete all as specified and directed. |
| 153 | a) 1 to 3 HP |
| 154 | b) 5 to 7.5 HP |
| 155 | c) 10 HP |
| 156 | d) 15 HP |
| 157 | e) 17.5 HP |
| 158 | f) 20 HP |
| 159 | Supply only thrust pads and bushes suitable for multi‑stage submersible pump of following capacity, complete all as specified and directed. . |
| 160 | a) 1 to 3 HP |
| 161 | b) 5 to 7.5 HP |
| 162 | c) 10 HP |
| 163 | d) 15 HP |
| 164 | e) 17.5 HP |
| 165 | f) 20 HP |
| 166 | Supply only dynamically balanced stainless steel shaft suitable for multi‑stage submersible pump of following capacity, complete all as specified and directed. . |
| 167 | a) 1 to 3 HP |
| 168 | b) 5 to 7.5 HP |
| 169 | c) 10 HP |
| 170 | d) 15 HP |
| 171 | e) 17.5 HP |
| 172 | f) 20 HP |
| 173 | Taking down existing Star‑Delta starter of the following capacity from the panel or mounting by carefully disconnecting all incoming and outgoing electrical connections; opening the enclosure; cleaning all contacts; tightening terminals; checking the operation of main, star, and delta contactors, overload relay, star‑delta timer, and single‑phase preventer; lubricating mechanical parts; replacing unserviceable minor parts such as control fuses, indicating lamps, and auxiliary contacts as directed; reassembling, reconnecting, testing, and commissioning the starter to ensure proper functioning, complete all as specified and directed.Note: Spare parts shall be measured and paid for separately. |
| 174 | a) 5 to 7.5 HP |
| 175 | b) 10 to 17.5 HP |
| 176 | c) 20 HP |
| 177 | d) 40 HP |
| 178 | Supply only main contactor, AC3 duty, 3‑pole, suitable for operation of Star Delta Starter of followingcapacity complete all as specified and as directed. . |
| 179 | a) 5 to 7.5 HP |
| 180 | b) 10 to 17.5 HP |
| 181 | c) 20 HP |
| 182 | d) 40 HP |
| 183 | Supply only star contactor, AC3 duty, 3‑pole, suitable for operation of Star Delta Starter of followingcapacity complete all as specified and as directed. |
| 184 | a) 5 to 7.5 HP |
| 185 | b) 10 to 17.5 HP |
| 186 | c) 20 HP |
| 187 | d) 40 HP |
| 188 | Supply only delta contactor, AC3 duty, 3‑pole, suitable for operation of Star Delta Starter of followingcapacity complete all as specified and as directed. |
| 189 | a) 5 to 7.5 HP |
| 190 | b) 10 to 17.5 HP |
| 191 | c) 20 HP |
| 192 | d) 40 HP |
| 193 | Supply only overload relay, adjustable range, suitable for protection of Star Delta Starter of followingcapacity complete all as specified and as directed. . |
| 194 | a) 5 to 7.5 HP |
| 195 | b) 10 to 17.5 HP |
| 196 | c) 20 HP |
| 197 | d) 40 HP |
| 198 | Supply only electronic Star–Delta timer, adjustable 0–30 seconds, suitable for automatic Star–Delta starter of followingcapacity complete all as specified and as directed. |
| 199 | a) 5 to 7.5 HP |
| 200 | b) 10 to 17.5 HP |
| 201 | c) 20 HP |
| 202 | d) 40 HP |
| 203 | Supply only single‑phase preventer (SPP) for protection against phase failure/reversal, suitable for operation of Star Delta Starter of followingcapacity complete all as specified and as directed. |
| 204 | a) 5 to 7.5 HP |
| 205 | b) 10 to 17.5 HP |
| 206 | c) 20 HP |
| 207 | d) 40 HP |
| 208 | Supply and fix in replacement Star‑Delta starter outdoor‑type centrifugal/jet pump controller (Star‑Delta starter) suitable for pump of following capacity, 440 V, 50 Hz, consisting of indicating lamp, voltmeter, ammeter, selector switch, and MCB (Make: L&T / Siemens / BCH), complete in and including outdoor weatherproof enclosure fabricated from 3 mm thick CRCA sheet, powder coated, of suitable size with front‑opening door, locking arrangement, and MS angle mounting legs and all necessary accessories, complete all as specified and directed. |
| 209 | a) 5 HP |
| 210 | b) 7.5 HP |
| 211 | c) 10 HP |
| 212 | d) 15 HP |
| 213 | e) 17.5 HP |
| 214 | f) 20 HP |
| 215 | g) 40 HP |
| 216 | Taking down existing DOL starter upto 5 HP capacity from the panel or mounting by carefully disconnecting all incoming and outgoing electrical connections; opening the enclosure; cleaning all contacts; tightening terminals; testing the operation of contactor, overload relay, and single‑phase preventer; lubricating mechanical parts; replacing unserviceable minor parts such as control fuses, indicating lamps, and auxiliary contacts as directed; reassembling, reconnecting, testing, and commissioning the starter to ensure proper functioning, complete all as specified and directed.Note: Spare parts shall be measured and paid for separately |
| 217 | Supply only main contactor, AC3 duty,1/ 3‑pole, suitable for operation of DOL starter of followingcapacity complete all as specified and as directed. |
| 218 | a) 0.5 HP |
| 219 | b) 1 HP |
| 220 | c) 2 HP |
| 221 | d) 3 HP |
| 222 | e) 5 HP |
| 223 | Supply only overload relay, adjustable range suitable for protection of DOL starter of followingcapacity complete all as specified and as directed. |
| 224 | a) 0.5 HP |
| 225 | b) 1 HP |
| 226 | c) 2 HP |
| 227 | d) 3 HP |
| 228 | e) 5 HP |
| 229 | Supply only single‑phase preventer (SPP) for protection against phase failure/reversal, suitable for DOL starter of followingcapacity complete all as specified and as directed. |
| 230 | a) 0.5 HP |
| 231 | b) 1 HP |
| 232 | c) 2 HP |
| 233 | d) 3 HP |
| 234 | e) 5 HP |
| 235 | Supply only control accessories including fuses, indicator lamps, push buttons, and necessary control wiring for DOL starter of followingcapacity complete all as specified and as directed. |
| 236 | a) 0.5 HP |
| 237 | b) 1 HP |
| 238 | c) 2 HP |
| 239 | d) 3 HP |
| 240 | e) 5 HP |
| 241 | Supply and fix in replacement outdoor‑type centrifugal/jet pump controller (DOL starter) suitable for following pump, 440 V, 50 Hz, consisting of indicating lamp, voltmeter, ammeter, and MCB (Make: L&T/Siemens/BCH), complete in and including outdoor weatherproof enclosure fabricated from 3 mm thick CRCA sheet, powder coated, of suitable size with front opening door, locking arrangement, and MS angle mounting legs; including all necessary accessories, complete all as specified and directed |
| 242 | a) 0.5 HP |
| 243 | b) 1 HP |
| 244 | c) 2 HP |
| 245 | d) 3 HP |
| 246 | e) 5 HP |
| 247 | Supply and fix in repair panel‑mounted LED indicator lamp, 22 mm, 230 V AC, with suitable colour lens (R/Y/G) for starter/control panel of jet pump motor of following capacity, complete all as specified and directed. |
| 248 | Supply and fix in repair panel‑mounted push button switch, 22 mm, heavy‑duty type with NO/NC contacts, suitable for starter/control panel of jet pump motor of following capacity, complete all as specified and directed. |
| 249 | Material and Labour for taking up/lifting out submersible pumpset of upto 7.5 HP capacity from open well / bore well using tripod chain pulley or any other suitable method, dismantling from MS/GI/HDPE pipe any size, opening pump set and carrying for repairs connecting back to pipe and lowering the submersible pumpset into open well / bore well in original position after repairs complete all as specified and as directed. |
| 250 | Material and Labour for taking up/lifting out submersible pumpset of 10 to 20 HP capacity from open well / bore well using tripod chain pulley or any other suitable method, dismantling from MS/GI/PVC pipe of any size, opening pump set and carrying for repairs connecting back to pipe and lowering the submersible pumpset into open well / bore well in original position after repairs complete all as specified and as directed.Note for item No. 71 & 72 : a) Unit rate quoted deemed to include labour cost including T&P for taking up & lowering the submersible pump from bore well/open well along with delivery pipe. b) Cost for repair work and replacement of spares will be measured and paid Separately under relevant items of sch. |
| 251 | Taking down existing unserviceable sluice valve of following sizes from the existing position and supply and fixing sluice valve CI body class PN 1.6 heavy duty flanged ends cast iron wheel with SS spindle conforming to IS short body including replacement of corroded nuts ,bolt, washers and gasket all as specified and as directed. |
| 252 | (a) 100mm dia |
| 253 | (b) 150mm dia |
| 254 | (c) 200mm dia |
| 255 | Material and Labour for opening the top of the Sluice valve of the following sizes carefully and taking out the gate incl spindle & checknut scrapping/Cleaning refacing, regrinding of gate of sluice valve and spindle, refixing the spindle, gate check nut and top of Sluice valve including repacking stuffing box of sluice valve spindle by replacement of gland packing rope of suitable size and reassembling including replacement of rubber gasket, Bolts, Nuts etc and making the sluive valve serviceable complete all as specified and directed NOTE : (i) Rate quoted deemed to include M&L cost for repair to sluice valve. (ii) Rubber gasket, bolts, nuts shall be measured and paid Separately as supply only under relevant items of sch here-in-after. |
| 256 | a). 100 mm dia |
| 257 | b). 150 mm dia |
| 258 | c). 200 mm dia |
| 259 | d). 300 mm dia |
| 260 | Supply and fixing Non return valve 150 mm, cast iron, PN-1.6 class with flanged ends with by-pass arrangement at both sides complete fitted with GI pipe incl connected accessories and joining materials complete all as specified and as directed. MAKE: Kirlosker/Upadhyaya/RMCO |
| 261 | All as per item no 75 here-in-before but non return valve of size 100mm all as specified and as directed. |
| 262 | All as per item no 75 here-in-before but non return valve of size 50mm all as specified and as directed. |
| 263 | Taking down the existing unserviceable hand pump from tube/ bore well by disconnecting mechanically and kept at site and Lifting the connection rod along with column pipe from bore hole and Segregating componets for carring out repair work including replacement of unserviceable chain along with chain link and plunger with nylon wahshers and lowering in the bore well and refixing the pump in its position complete all as specified. Note: Rate quoted includes labour cost lifting/Lowering of pipe. |
| 264 | Supply and fix terminal plate with MS cover suitable for the folllowing capacity motors of any make |
| 265 | (a) 0.5 to 5 HP Capacity Motor |
| 266 | (b) 7.5 to 10 HP Capacity Motor |
| 267 | (c)15 to 17.5 HP Capacity Motor |
| 268 | (d) 40 HP Capacity Motor |
| 269 | Supply and fix the following items |
| 270 | (a) Gasket Sheet of 4mm thickness |
| 271 | (b) Gasket Sheet of 6mm thickness |
| 272 | (c) Asbestos Graphited Gland Packing rope of size 8mm to 16 mm |
| 273 | (d) GI bolt & Nuts with double washers in different sizes |
| 274 | Supply and fixing Pressure gauge of size 4\" (Scale 0 to 14 kg/cm2) suitable for 20/40 HP Centrifugal Pump set without any water leak alongwith connected items including taking down old unserviceable one all as directed. |
| 275 | Material and labour for preparing the surface of MS pipe line,valve chamber door and panel board and painting with two coat of synthetic enamel paint of existing colour over a coat of red oxide primer including scrapping out of old fadded paint all as specified and as directed |
| 276 | Supply and Fix contactor 3 pole with AC1 duty coil 40 Amps AC-1 duty rating at 415V, 50Hz, power poles 3 Auxillary contact arrangement NO/NC and taking down the existing unserviceable one all as specified. |
| 277 | Supply and Fix contactor 3 pole with AC1 duty coil 18 Amps AC-1 duty rating at 415V, 50Hz, power poles 3 Auxillary contact arrangement NO/NC and taking down the existing unserviceable one all as specified. |
| 278 | Replacement of worn‑out transparent nylon type Love Joy spider suitable for following pump capacity by dismantling existing coupling, removing damaged spider, cleaning the coupling hubs, and fixing new Love Joy spider including necessary nuts, bolts, and alignment; reassembling and testing for smooth operation, complete all as specified and as directed. |
| 279 | a) 1 to 5 HP |
| 280 | b) 5 to 15 HP |
| 281 | c) 20 to 40 HP |
| 282 | Supply and lay / lowering PVC insulated stranded copper conductor cable flat type water proof 3 core 1100 voltage grade of Following sizes suitable for submersible pumpset complete all as specified and directed. Make:- Asian/Polycab. |
| 283 | a) 2.5 sqmm suitable for submersible pumpset complete all as specified and directed. |
| 284 | b) 4 sqmm suitable for submersible pumpset complete all as specified and directed. |
| 285 | b) 6 sqmm suitable for submersible pumpset complete all as specified and directed. |
| 286 | c) 10 sqmm suitable for submersible pumpset complete all as specified and directed. |
| 287 | Material and labour for Earthing complete with GI earth plate electrode of size 600mm x 600mm x 6 mm thick buried directly in ground vertically to a depth of not less than 2.25 m deep below normal ground level, with top edge of the earth plate at a depth of not less than 1.5 mtr below ground connected to GI earth strip 32 x 6mm by means of GI bolts and nuts, washers and GI earth strip protected by GI pipe light grade 40mm bore upto 7.5 mtr and connecting to LT switch gear panel etc as per site requirement including necessary excavation, earth work in any type of soil, PCC 1:3:6 type C-1 earth chamber, 40mm thick RCC cover with 6mm dia MS bars 10cm C/C on both ways as reinforcement complete all as shown in electrical plate No 3 of MES Schedule Part 1 connected to earthing test points complete all as specified and as directed Note :- (i)Quoted rate deemed to include necessary earth work, PCC chamber, RCC cover, reinforcement, removal of surplus soil, site clearance etc. (ii) GI earth strip 32 x 6mm, GI tubing light grade 40mm bore upto 7.5 mtr deemed to be included in the rate quoted by the contractor. (iii) Beyond 7.5 mtr the GI earth strip 32 x 6mm & GI pipe light grade 40mm bore shall be measured under relevant item of the schedule. |
| 288 | Supply and fix on pole/buried in ground Earth continuity conductor GI strip 32mm x 6mm fixed to wall on batten or buried in ground or drawn in conduit/pipe or fixed to poles complete. |
| 289 | Supply and fix for MCCB 4 Pole, 415 V, Adjustable Thermal & fixed Magnetic release 125 Amp with breaking capacity 16 KA,ICS=100%ICU complete all as specified and as directed. Make : Legrand/ Siemens /schneider/ABB Note : Including taking down old unserviceable. |
| 290 | All as per item No 38 here-in-before but MCCB 4 Pole, 415 V, Adjustable Thermal & fixed Magnetic release 200 Amp with breaking capacity 36 KA,ICS=100%ICU complete all as specified and as directed. |
| 291 | All as per item No 38 here-in-before but MCCB 4 Pole, 415 V, Adjustable Thermal & fixed Magnetic release 100 Amp with breaking capacity 16 KA,ICS=100%ICU complete all as specified and as directed. |
| 292 | All as per item No 38 here-in-before but MCCB 4 Pole, 415 V, Adjustable Thermal & fixed Magnetic release 160 Amp with breaking capacity 25 KA,ICS=100%ICU complete all as specified and as directed. |
| 293 | Supply and fixing MCB,4 pole,415 Volts 63 Amps, 10KA \"C\" series Including taking down old unserviceable ,Make:Legrand/Siemens/Schneider/ABB |
| 294 | Supply and fixing MCB,4 pole,415 Volts 32 Amps,10KA \"C\" series Including taking down old unserviceable, Make:Legrand /Siemens/Schneider/ABB |
| 295 | Material and labour for preparing the old surface of centrifugal pump with motor along with MS Frame of following capacity and painting with two coat of synthetic enamel paint of approved tint including scrapping out of old fadded paint and writing the SM/MES.No as directed all as specified and as directed |
| 296 | a) Upto 2 HP |
| 297 | b) 3 HP |
| 298 | c) 5 to 10 HP |
| 299 | d) 15 HP |
| 300 | e) 20 HP |
| 301 | f) 40 HP |
| 302 | Taking down existing damaged/corroded mild steel base frame of pump set by disconnecting pump and motor assembly, removing old frame, supplying and fixing new MS base frame of same size and gauge, including cutting, welding, drilling, grinding, and applying one coat of red oxide primer and two coats of synthetic enamel paint; refixing pump and motor on new frame with proper alignment, reconnecting electrical and mechanical connections, and testing for smooth operation, complete all as specified and directed. |
| 303 | a) upto 15 HP |
| 304 | b) 15 to 40 HP |
| 305 | Supply and fix first aid kit box fabricated from high‑grade GI metal with front transparent glass and painted in red and white colour; complete with wall‑mounting arrangement, hinges, and locking provision, complete all as specified and directed |
| 306 | Supply only complete first aid medical kit containing adhesive bandages, crepe bandages, medical tapes, antibiotic treatment application, pain‑relief gel, antiseptic solution, burn‑dressing gel‑soaked pads, burn‑treatment cream, disposable gloves, scissors, Paracip tablets (10 Nos), soaking cotton, and other standard first aid materials, complete all as specified and directed |
| 307 | Material and labour for printing water supply distribution line diagram on flex, fixed in metal frame of size 1.5 m × 1 m and securely mounted on wall by removing old flex board, complete all as specified and directed by Engineer‑in‑Charge.Note: Line diagram to be printed on flex shall be provided by Engineer‑in‑Charge. |
| 308 | Supply and fix sign board fabricated with metal frame of size 1 m × 0.6 m and 3 mm thick metal sheet, duly painted with name of installation written, by removing old sign board; including stand made of angle iron and PCC foundation work for fixing in ground, complete all as specified and directed. |
| 309 | Supply and fix notice board of size 1 m × 0.6 m × 0.2 m made of soft board wood covered with 12 mm thick cotton cloth, duly fixed on wall with necessary arrangements, complete all as specified and directed |
