Maintenance of completed scheme under Nazul A/C-II/HZ. Sub Head :-Providing and Installing open gym equipments with Buyback of old equipment in DDA parks under the jurisdiction of Horticulture Civil Division-IV,Hort. Zone, DDA (Specialized Work).; 1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m inwidth or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(a) All kinds of soil. 2 Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.(a) All kinds of soil 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a) 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a)1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 5 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :(a) 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 6 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 7 Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light traffic parkingetc, of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colour & pattern over 50 mmthick compacted bed ofsand, compacting and proper embedding/layingof inter locking paver blocks into the sand bedding layer through vibratorycompaction by using plate vibrator, filling the joints with sand and cuttingof paver blocks as per required size and pattern, finishing and sweepingextra sand. complete all as per direction of Engineer-in-Charge.(a) 60 mm thick cement concrete paver block of M-35 grade withapproved colour, design & pattern. 8 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 9 Dismantling SBR (Styrene Butadiene Rubber) tile flooring manually/ by mechanical means, including stacking of serviceable material and disposal of unserviceable material, with all leads and lifts, complete as per direction of Engineer-in-Charge. 10 Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. hollow tube frame or as decided by Engineer-in-Charge (Payment of M.S. frame shall be paid separetely). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. 11 Total 12 Modified estimate cost after using correction factor on DSR 2023 on account of GST @ 0.973 on Schedule A 13 Amount after applying cost-index @ 3%, say total A 14 Schedule BAir Walker: Providing and fixing air walker with below specifications:1. Dimensions (LxWxH): 1100 x 450 x 1300mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. ‘U’ shaped main frame of NB 80mm (G.I.) ‘C’ Class Pipe, Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe.4.Handle frame pipes of NB 32mm (G.I.) ‘C’ Class.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored.9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly.15. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use.17. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. 18. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 15 Sit up station : Providing and fixing Sit up stationin a pair with below specifications:1. Dimensions (LxWxH): 1500 x 1150 x 650mm2. Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe.4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)5. Perforated MS Sheet for Back Support.6. The back support Fixed on its top is made of perforated MS sheet of 2mm thickness.7. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick.8. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.9. Zinc primer paint is applied at all welding points prior to finishing.10. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.11. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.12. Once the concrete is set, the equipment is fixed on to it.13. High tensile steel with galvanized nut bolts are used for assembly.14. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.15. Self-Explanatory stainless steel label fixed on equipment for ease of use.16. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.17. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 16 Air Swing: Providing and fixing air swing in a pair with below specifications:1. Dimensions (LxWxH): 1150 x 900 x 1250 mm2. Fabricated with main post of NB 100 mm (G.I.) ‘C’ Class Pipe of approved make.3. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe.4. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.18. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.19. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 17 Horse rider station: Providing and fixing horse rider station with below specifications:1. Dimensions (LxWxH): 1000 x 600 x 1100 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe.4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.9. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.18. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.19. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years20. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 18 Leg Press: Providing and fixing leg press in a pair with below specifications:1. Dimensions (LxWxH): 2000 x 550 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe.9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmentalfriendly.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly.15. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use.17. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.18. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 19. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 19 Pull Chair:Providing and fixing Pull Chair in a pair with below specifications:1. Dimensions (LxWxH): 2400 x 800 x 2000 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe.4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.18. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.19. Cost of earth work and concrete in foundation to be paid for separately.including maintenance cost for 2 years. 20. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 20 Seated Chest Press:Providing and fixing Seated Chest Press in a pair with below specifications:1. Dimensions (LxWxH): 1800 x 700 x 2000 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use. 18. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. 19. Cost of earth work and concrete in foundation to be paid for separately. including maintenance cost for 2 years. 20. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 21 Arm wheel: Providing and fixing arm wheel in a pair with below specifications:1. Dimensions (LxWxH): 850 x 800 x 1800 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipesmust be (G.I.) ‘C’ Class Pipes.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.9. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.11. High tensile steel with galvanized nut bolts are used for assembly.12. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.13. Self-Explanatory stainless steel label fixed on equipment for ease of use.14. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.15. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years16. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 22 Elliptical Exerciser:Providing and fixing elliptical exerciser with below specifications:1. Dimensions (LxWxH): 1200 x 550 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.13. High tensile steel with galvanized nut bolts are used for assembly.14. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.15. Self-Explanatory stainless steel label fixed on equipment for ease of use.16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.17. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.18. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 19. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 23 Double cross walker: Providing and fixing double cross walker with below specifications:1. Dimensions (LxWxH): 1600 x 600 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe.5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored.9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly.15. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use.17. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.18. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 19. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 24 Twister: Providing and fixing triple twister with below dimensions:1. Dimensions (LxWxH): 1300 x 1300 x 1300 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe.4. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. Foothold plate of made of MS Sheet Metal of 3mm thickness.6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all the welding points prior to finishing.9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.10. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use.15. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.16. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 25 Rowing machine: Providing and fixing rowing machine with below specifications:1. Dimensions (LxWxH): 1250 x 800 x 1150 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe.4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.9. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.18. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range.19. Cost of earth work and concrete in foundation to be paid for separately.Including maintenance cost for 2 years 20. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 26 Weight Assisted Shoulder Press Weight Assisted Shoulder Press of minimum size 1350x1600x1150mm fabricated with main post of G.I. ‘C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘ C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI C Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. Cost of earth work and concrete in foundation to be paid for separately.including maintenance cost for 2 years. . This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 27 Weight Assisted Chest PressWeight Assisted Chest Press of minimum size 1100x1500x1300mm fabricated with main post of G.I. ‘ C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘ C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI C Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. Cost of earth work and concrete in foundation to be paid for separately.including maintenance cost for 2 years.This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 28 Weight Assisted Lat Pull DownProviding, designing and fixing of Weight Assisted Lat Pull Down of minimum size 1200x1300x1650mm fabricated with main post of G.I. ‘ C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘ C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI C Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. Cost of earth work and concrete in foundation to be paid for separately.including maintenance cost for 2 years. . This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. 29 Weight Assisted Rowing MachineWeight Assisted Rowing Machine of minimum size 1500x1450x1650mm fabricated with main post of G.I. ‘ C’ Class of NB 65 mm and othersupport and handle frames of NB 50 mm G.I. ‘ C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges andburrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI C Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Chest support to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by atleast 2 KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. Cost of earth work and concrete in foundation to be paid for separately.including maintenance cost for 2 years. 30 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(i) Air Walker. 31 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(ii) Sit up Station. 32 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(iii) Air Swing. 33 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(iv) Horse rider station. 34 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(v) Leg press. 35 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(vi) Pull chair. 36 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(vii) Seated chest press. 37 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(viii) Arm wheel. 38 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(ix) Elliptical exerciser. 39 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(x) Double cross walker. 40 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(xi) Twister. 41 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(xii) Rowing machine. 42 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(xiii) Weight Assisted Shoulder Press. 43 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(xiv) Weight Assisted Chest Press. 44 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(xv) Weight Assisted Lat Pull Down. 45 Buy-back of old gym equipment in as-is condition including taking away from site without dismembering, with dismantling, loading, transportation, and disposal, all complete as per direction of Engineer-in-Charge.(xvi) Weight Assisted Rowing Machine. 46 Total absolute amount of items from 27(i) to 27(xvi) “X” 47 Total B = (sum of item no. 11 to 26 ) + X 48 NOTE: Buy-back rates of old gym equipment in item no. 27 are fixed and Contractor Enhancements will not be applicable on them. SCHEDULE CComprehensive annual maintenance cost for five year of all the open gym equipments (Item no. 11 to 26 of Schedule B) 49 Comprehensive annual maintenance of open gym equipment (Item No. 11 to 26 of Schedule B) for 3rd year after completion of initial two years free maintenance by the agency, complete as per direction of Engineer-in-Charge. 50 Comprehensive annual maintenance of open gym equipment (Item No. 11 to 26 of Schedule B) for 4th year complete as per direction of Engineer-in-Charge. 51 Comprehensive annual maintenance of open gym equipment (Item No. 11 to 26 of Schedule B) for 5th year, complete as per direction of Engineer-in-Charge.
