Tender For Certain Major Revenue And Minor Works (B/R And E/M) At Certain Locations At Chaf Bangalore; 1 COMMON ITEMS APPLICABLE FOR JOB A, JOB B , JOB C & JOB D (B/R & E/M) :- 2 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft loose soil complete all as specified & directed.(Sl no 1 of job a+SL no 1 of Job b+ Sl no 1 of Job c) = 80+20+80=180 3 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense soil complete all as specified & directed.(Sl no 1 of job a+SL no 1 of Job b) = 5+10=15 4 M&L for PCC 1:4:8 Type D2 (40mm graded stone aggregare) in foundations, filling and mass concrete complete all as specified & directed..(Sl no 5 of job a+SL no 3 of Job b+SL no 2 of Job c+SL no 6 of 3 a(i) ofJob c)=5+1+2+2=10 5 M&L for Pre cast cement concrete block masonry with soild blocks, type C1 (1:3:6) using 20mm graded aggregate exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed.(Sl no 6 of job a+SL no 14 of Job b+SL no 3 of Job c+Sl no 12 of 3 a(i) of job c) = 12+12+4+2=30 6 M&L forrendering 10mm thickin cement morter 1:6 and5mm thick in cement morter 1:4 in two layers on fair faces of brick work or concrete surfaceswith water proofing compound @ 200 ml per 50kg of cement or as per manufacturers instruction etc finished even and smooth without using extra cement complete all as specified and as directed.(Note : WPC shall be measured and paid separetely)(Sl no 7 of job a+SL no 17 of Job b+SL no 4 of Job c+Sl no 15 of 3 a(i) of job c) = 100+30+20+50=200 7 M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.(Sl no 6 of job a+SL no 19 of Job b+SL no 5 of Job c)=22.5+1.2+25=48.7 8 M&L for 100 mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring or pavings etc all as specified and directed(Sl no 9 of job a+SL no 6 of Job c) = 50+50=100 9 M&L for 75mm thick Cement concrete type B2, 1:2:4 (using 40 mm graded stone aggregate) asinflooring or pavings etc all as specified and directed(Sl no 10 of job a+SL no 7 of Job c) = 50+50 10 M&L 7.5cm thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required complete all as specified and directed(Sl no 11 of job a+SL no 23 of Job b+SL no 8 of Job c) =8+1+20 11 M&L for machine pressed precast concrete interlocking coloured rubber moulded paver blockwith grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade laid over and including 40-50mm thick M sand cushion all as specified and as directed by Engr-in-Charge.(Sl no 12 of job a+SL no 24 of Job b+SL no 9 of Job c) = 80+10+200=290 12 M&L for providing, cement concretetype B-0 (1:2:4) using 12.5mm graded stone aggregate asin roof kerbs, padding or mud stops, rounded or chamfered on edges all as specified and directed(Sl no 15 of job a+SL no 15 of Job b+Sl no 13 of 3 a(i) of job c) =1+1+1=3 13 M &L for preparing newplastered or un plastered old surface of walls and applying two coats of Cement base paint on walls.(External)including with alkali resistant priming paint complete all as specified and directed.(Sl no 19 of job a+SL no 28 of Job b) =100+30=130 14 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.of hard/dense soil.(Sl no 20 of job a+SL no 29 of Job b+Sl No 5 of Job 5 (c) of job b) =3+7+119=129 15 Removing Excavated soilsexceeding 1.5 Kmbut not exc. 5 Km and depositing where directed.(Sl no 21 of job a+SL no 30 of Job b)=2+8=10 16 M&L for preparation of new surfaces of steel over 10cm in width or girth with two coat of synthetic enamel paint over coat of primer red oxide primer complete all as specified and directed.(Sl no 22 of job a+SL no 34 of Job b+Sl no 65 of 3 a(i) of job c) =70+40+20=130 17 M&L for 75mm thick cement concretetype C-2, 1:3:6 (40 mm graded aggregate) as in plinth protection/sub base of floorcomplete all as specified and directed.(Sl no 23 of job a+SL no 25 of Job b) =50+15=65 18 S & F framed work such as grills, grating, etc.. With ends of bars shouldered and/or rivted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-formig to Fe.290. Gde-E-165 complete all as specified and directed.(Sl no 24 of job a+SL no 33 of Job b) =250+87=337 19 Preparing newly plastered surfaces of ceiling and applying three coats of white washcomplete all as specified and directed.(Sl no 6 of job d+SL no 27 of Job b)=45+12=57 20 M&L cutting chases, pinning in, makinggood to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps,cills, sunshades, shelves, lintels, etc.;and cutting chases for concealedwater tubing or concealed conduitwiring, etc. and making good,cutting exceeding 20cm girth complete all as specified and directed(SL no 16 of Job a+Sl no 18 of 3 a(i) of job c)=20+=22 21 S&F for pre-painted galvalume aluminium zinc coating GIbased carrugated steel sheet 0.50 mm th of ancolour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws acomplete all as specified and directed(SL no 17 of Job a+Sl no 19 of 3 a(i) of job c)=170+12=182 22 Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridge of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directedNote : For shed with SNCOs mess(SL no 18 of Job a+Sl no 20 of 3 a(i) of job c)=40+1 23 M&L for Formwork to sides and soffits of rough finished surfaceof floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed(Sl no 24 of 3 a(i) of job c+Sl no 5 of Job b)=4+15=19 24 M&L for Formwork to soffits of rough finished surface of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed(Sl no 26 of 3 a(i) of job c+Sl no 6 of Job b)=2+12=14 25 M&L for Formwork to edges/sides of rough finished surface of roof slab 15cm thick complete all as specified and directed.Sl no 27 of 3 a(i) of job c+Sl no 8 of Job b =5+12=17 26 M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shaperequired, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clipscomplete all as specified and directed.(Sl no 30 of 3 a(i) of job c+Sl no 12 of Job b)=50+200=250 27 M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm diain stirrups, spacers and binderscomplete all as specified and directed.(Sl no 31 of 3 a(i) of job c+Sl no 13 of Job b)=10+100=110 28 M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified and as directed.(Sl no 14 of 3 a(i) of job c+Sl no 16 of Job b)=50+20=70 29 Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc(Sl no 1 of 3 a(i) of job c+Sl no 2 of Job d)=20+118=138 30 M&L for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable connected to common earth and earth dolly with suitable copper lugs drawing into and including rigid non-metallic PVC concealed conduit of 20mm dia or higher, medium grade complete with all PVC conduit accessories, including metal flush box of 1.60 mm thick suitable for modular switches/ sockets/fan regulators including modular white cover plate and modular metal flush box with frame of required modules at site, blanking plates,brass screws, cup washers etc including all cutting / chases etc in stone/ brick masonary/ walls, pinning in stone walls / brick walls and pointing in cement mortar 1:3 to ends or edges of landing etc for concealed conduit wiring using heavy duty stone drilling/cutter machine and making good to the disturbed surfaces to match the existing complete all as specified and directed for the followings:- 31 One light/ceiling fan/ point/ exhaust fan/ bell Pointcontrolled by one, one way switch 06 Amps(Sl no 1.01,1.02,1.03,1.06 of Job c+ Sl no 1 of 2(b) Job b )=6+1+1+1+5=14 32 One 3 pin, 06 Amps socket outlet point on independent board controlled by one, one way 06 Amps switch(Sl no 1.04 of Job c+ Sl no 2 of 2(b) Job b)=10+2=12 33 One 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch.(Sl no 1.05 of Job c+ Sl no 3 of 2(b) Job b )=1+1=2 34 All as per item No 29 above but point wiring with 2.5 Sqmm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete(Sl no 2.00 of Job c+ Sl no 4 of 2(b) Job b)=10+2=12 35 S&F modular switch, 10 Amps, single pole, one way, 230 volts, one module complete all as specified and directed (Sl no 3.00 of Job c+ Sl no 5 of 2(b) Job b )=19+8=27 36 S&F modular switch, with indicator, 16 Amps, single pole, one way, 230 volts complete all as specified and directed (Sl no 4.00 of Job c+ Sl no 6 of 2(b) Job b)=10+2=12 37 S&F modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified and directed (Sl no 5.00 of Job c+ Sl no 7 of 2(b) Job b)=11+3 38 S&F modular socket outlet 02 in 01, 03 pin,16 Amps, 02 module with shutter complete all as specified and directed(Sl no 6.00 of Job c+ Sl no 8 of 2(b) Job b)=10+2=12 39 S&F ceiling rose, 65 x 50 mm surface type with 3 terminals incl connection complete all as specified and directed(Sl no 9.00 of Job c+ Sl no 9 of 2(b) Job b )=8+5=13 40 S&F on surface/wall mountedLED batten, robust extruded aluminium housing and intigrated electronic drive20 watt, 4 feet, with accessories including connection with 2 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed (Sl no 11.00 of Job c+ Sl no 15 of 2(b) Job b)=6+5=11 41 ITEMS APPLICABLE FOR JOB A(B/R) :- 42 Excavation in post holes each not exc 0.50 cum in any type of soil , getting out, returning filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 cm ,watering and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed. 43 M&L for cement concrete Type C2 1:3:6 (40 mm graded aggregate) in foundations ,filing and mass concrete complete all as specified and directed. 44 S&F Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates etc complete all as specified and directed. 45 S&F Plates (plain or chequered) channels,distance pieces, cleats etc square cut or notched including riveted, bolted or welded attachment complete all as specified and directed 46 ITEMS APPLICABLE FOR JOB B(B/R & E/M) :- 47 Use and waste of Formwork to sides flat rough finished of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 48 Use and waste of Formwork to rough finished surfaceof concrete flat chajjas, troughs and similar items including edges complete all as specified and directed. 49 M&L for RCC (Nominal mix) type B1 1:2:4 using20mm graded aggregate for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 50 M&L for RCC (Nominal mix) type B1 1:2:4 using20mm graded aggregate for RCC Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. 51 M&L for RCC (Nominal mix) type B1 1:2:4 using20mm graded aggregate for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 52 M&L for rendering 5mm thick on concrete surfaces of ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed. 53 M&L for 75mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring or pavings etc complete all as specified and directed. 54 M&L for 100 mm thick PCC 1:2:4 type B2 (using40 mm graded aggregate ) as inhard standing/ floor finishes etc. laid in alternate panels complete all as specified and directed. 55 M&L for sand fillingunder floors or foundation, and receiving to interlocking tiles, complete all as specified and directed. 56 M&L for preparation of newly plastered surface of wall and apply three coats of white wash complete all as specified and as directed. 57 S&F steel window/ventilator with side hung shutter including projecting type hinges with steel handles and steel peg stay and with glazing bars complete with dovetailed or welded complete all as specified and directed. 58 S&F 4mm thick sheet glass ordinary quality and fixed with aluminium beading in square not exc. 0.50 sqm in each pane complete all as specified and as directed. 59 S&F Sheet metal enclosure double door type for TPNDBs (when MCB to be used) 4 way 415 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. 60 S&F MCB TPN, 415 volt any rating from 63 amps C series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed. 61 S&F MCB Single pole and neutral 240 volt any rating from 40 amps C series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed. 62 S&FMCBsingle pole 240 volt any rating from 10 to 40 amps C series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed. 63 S&F Sub main wiring with6.00 Sqmm nominal cross sectional area, two single core, 1100 volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 6.00 Sqmm nominal cross sectional area, single core, 1100 volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit not less than of 25 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases, pinning etc in stone/ brick masonary/ walls and making good to the disturbed surfaces to match the existing complete all as specified and directed. (Note : One run of earth continuity conductor, one run of PVC conduit and two runs of copper conductor shall be together taken as one length for measuring unit length) 64 S&F GI pipe Medium grade 50mm dia including all fittings to provide the water supply for the proposed Building complete all as specified and directed. 65 S&F GI pipe Medium grade 40mm dia including all fittings to provide the water supply for the proposed Building complete all as specified and directed. 66 S&F GI pipe Medium grade 25mm dia including all fittings to provide the water supply for the proposed Building complete all as specified and directed.. 67 Excavation in trenches, not exc.1.5 m wide and not exc. 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, cesspits, manholes, pier holes, etc. n. exc.10 Sq m on plan and not exc. 1.5 m in depth in soft/loose soil and getting out complete all as specified and directed. 68 Removing of surplus soil to a distance not exceeding 50 mtr and depositing at a place not exceeding 1.5 mtr specific wide above the starting point complete all as specified and directed. 69 S&F Gun metal globe or gate valve with iron wheel head,screwed both ends for iron pipe of size 50 mm complete all as specified and directed. 70 All as per Item No 68.00 here-in-before but of size 40 mm 71 All as per Item No 68.00 here-in-before but of size 25 mm 72 Cutting of existing GI/CI water main pipe line upto 80-150 mm bore in position for making branch connection (insertion of GI Tee) including excavation and earth work complete all as specified and directed.Note : GI fittings such as tee, elbows, collar, reducer etc joint and jointing material for fixing of cast iron fittings shall be measured and paid separately. 73 S&F DOL starter single phasefor 5 HP submersible pump Single Phase 230 Volts complete all as specified and directed. 74 M&L for submersible pump of capacity 5 HP head 23 mtr discharge 380 LPM,delivery size50mm with SS Impeller & Casingwith1 phase motor 230 volts and all connection complete all as specified and directed. Note:(01 pumpis considered for reserve) 75 Supply and laying cable XLPE insulated armoured heavy duty electriccable with aluminium conductor 1100 volt grade having cross sectional area of size 25 Sqmm 3.5 core complete all as specified and directed. 76 Cutting of existing road for crossing of MS/DI/CI/GI pipes for laying of any size pipes including necessary exacavation and earth work including repairing the same as per existing with pre mix bituminuos carpet complete all as specified and directed. 77 S&F Earthing of machinery/equipment Installed at power house/substation with galvanised steel earth plate electrode 600 mm × 600 mm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised iron strip 32 x 6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing complete all as specified and directed. 78 ITEMS APPLICABLE FOR JOB C(B/R & E/M) :- 79 Taking down chowkat or frame with shutter (without taking off shutter from the frame) not exc 1.5 sqm each, making good disturbed surfaces and removing materials from site of work complete all as specified and directed. 80 Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc 1.5 sqm but n exc4sqm each, making good disturbed surfaces and removing materials from site of work complete all as specified and directed. 81 Dismantling floor, hearth or wall tiling incl cement mortar bedding ( but not backing) and rubbish off the premisies complete all as specified and directed. 82 Cutting openings, through brick walls for door, window,and other openings orenlarging existing openings.converting window into door,openings, etc or cutting out ,defective brick work for,under-pinning, including,providing, fixing and removing shoring, cleaning and stacking bricks,removing surplus serviceable bricks, hard-core to store and rubbish not exc 50mcomplete all as specified and directed. 83 M&L for type B-2, 1:2:4 (40 mm graded aggregate) as in pilasters buttresses columns, pillars, boundary pillars and posts (incl caps and bases)complete all as specified and directed. 84 M&L for25 mm thick cement concrete type B11:2:4 using 20 mm graded stone aggregate as in levelling concrete finished even and fair to recive floor finshes, complete all as specified and directed. 85 M&L for Non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.18 sqm but n exc 0.38 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles,laid over and including cement screed bed 15 mm thick in cement mortar 1:6 laying floor finish complete all as specified and directed. 86 M&L for vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm light shed, in floors etc laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to matchcomplete all as specified and directed. 87 M&L for vitrified ceramic coloured tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqmlaid over and including 10mm thick rendering in cement mortar 1:3 on vertical surfaces such as skirtings, dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shadecomplete all as specified and directed. 88 M&L Glazed ceramic tiles coloured of size 450X 300X 7mm thick as vertical surface set and jointed in neat cement slurry and pointed in white or colour cement mixed with pigment to match the shade of the tiles with 10 mm th rendering in cement mortar 1:3 for laying wall finishes complete all as specified and as directed. 89 M&L Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and tabil top for fixing wash basin and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite shade includingscreed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishescomplete all as specified and directed. 90 S&F roof trusses (framed), trussed, purlins,crane gantries, rails and fastnings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. fe-410 (gde E-250)complete all as specified and directed.Note : Location of work is shed with SNCOs mess 91 S&F plates (plainor chequered) channels,distance pieces, cleats etc.square cut or notched including riveted, bolted or welded attachment complete all as specified and directed.Note : Location of work is shed with SNCOs mess 92 S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders;framed balusters; walk ways; railings; framework of water tanks and framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.Note : Location of work is shed with SNCOs mess 93 M&L for RCC (nominal mix) M-25 using 20mm graded agg for RCC Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. 94 M&L for RCC (nominal mix) M-25 using 20mm graded agg Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 95 S&F Powder coated Aluminium windows/cubboard shutter oftwo tracks outer frame top, side sections, bottom frame(track) with guide track of size 92.5x31x1.50mm with slidingwindow shutters two nos with 5mm thickPVC plain coloured sheet frame top and side bottom section with wheel track and inner locking section of size 40X18X1.5mm inculding 5mm thick plain colour PVC sheet complete all as specified and directed. 96 S&F Pressed steel frames for doors size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc complete all as specified and directed. 97 S&F Pressed steel frames for doors size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc complete all as specified and directed. 98 M&L for PCC 1:3:6 type C-1 using 20mm graded aggregate as filled in pressed steel foor frames etc complete all as specified and as directed. 99 M&L for PCC 1:3:6 type C-1 using 20mm graded aggregate as in hold fast block including necessary form work etc complete all as specified and as directed. 100 S&F for 35 mm thick factory made second class hard wood plain framed panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commecrcial ply or 12mm veneered particle board with commecrcial veneering on both face. The size of rail and stile as per IS 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. 101 S&F 35mm thick IIst class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, divided into squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats, complete all as specified and directed. 102 S&F Powder coated Aluminium windows of three tracks outer frame top, side sections, bottom frame(track) with guide track of size 92.5x31x1.50mm with slidingwindow shutters two nos with glass and one no with wire mesh(total 3 nos shutter) frame top and side bottom section with wheel track and inner locking section of size 40x181.5mm inculding glass 4 mm thick and aluminium wire cloth, 0.45mm nominal dia wire and average width of aperture 1.40mm complete all as specified and directed. 103 S&F Powder coated Aluminium Frame work for grills Deco-grill Model DG-104 (10mm)making shape and riveted with rivetsand fixed with suitable channel complete necessary fixing arrangements etc.,completed and directed by Engr-In-Charge. 104 S&F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. 105 S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed. 106 S&F 100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed. 107 S&F floor door stopper of aluminium alloy body overall length of cover plate 150mm and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 108 S&F 18 to 19mm thick pre-laminated partical board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination, and fixed with screw and Continuous (piano) hinges, 125mm longHasp and staple and prepare kitchen cabinatewith shutter (and one ortwo selfas per site requirement for sorage) and hanging on wall and also fixed totimber frame work where required complete all as specified and directed. 109 S&F kitchen sink faucet mixer tap ,Chrome polished ofAtom pull down, mechanical docking ,deck mounted , dual spray models,360° swivel water saving aerated flow complete all as specified and directed.Make:kohler or any techno-commerically equivalent make in Moen Haelyn. 110 S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm, fixed as in repairs, complete all as specified and as directed. 111 S&F in repairs 15mm pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure,with or without lettered hot or cold with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed. 112 S&F PVC connection pipe 600mm long 15mm dia both end having brass coupling nut and PVC washer complete all as specified and directed. 113 S&F in repairs vitreous China wash basin, white flat back, size 550x400mm including brackets, 32mm dia CP waste coupling, waste pipe, short connection complete cutting for and pinning in ends of brackets or ereesing stand complete all as specified and directed. 114 S&F Rotational moulded polythylene 500 litres capacity waterstorage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including20 mm ball valve high prressure oof PTMT with epoxy coated alu rod & high density plastic ball complete all as specified and directed. 115 S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specified and directed. 116 S&F CP two way stop cock with all accessories complet all specified and directed. 117 S&F in repairs 15 mm bore fency typeCP bib tapscast copper alloy with crutch or butterfly nuts , handle, screwed down for iron pipe complete all as specified and directed. 118 S&F gratings doom,100mm dia of PTMT (minimum weight 25 gms) complete all as specified and directed 119 S&F gratings doom,125mm dia with waste hole of PTMT (minimum weight 40 gms) complete all as specified and directed 120 M&L application for two coats of synthetic enamel paint on new wooden surfaces over coat of pink primer to new surfaces including preparation of surfaces,over 10cm width or girth complete all as specified and directed. 121 S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor,includingcomplete all as specified and as directed . 122 S&F 75mm PVC (SWR)pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor,including complete all as specified and as directed. 123 S&F 110mm bore PVC (SWR) bends any radius complete all as specified and as directed. 124 S&F 75mm bore PVC (SWR) bends any radius complete all as specified and as directed. 125 S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. 126 M&L for preparation of new plastered surfaces of wall surfaces andapplying two coats of oil bound distemper over a coat of alkali resistant priming paint complete all as specified and as directed. 127 M&L for applying2 mm thickwall care putty on wall including preparation of new surfaces plastered or unplastered surfaces complete all as specified and directed. 128 M&L for preparing newplastered or unplastered old surface of walls and applying two coats of Cement base paint on walls including with alkali resistant priming paint complete all as specified and directed. 129 S&F modular Bell push 6 Amps, one module 240 volts complete all as specified and directed. 130 S&F Ding Dong Bell, AC, 230 volts, Single Pole incl connection complete all as specified and directed. 131 Cutting into or through the stone walls / brick wallsbuilt in cement mortar or cement lime mortar and walls of cement concrete suitable sizefor housingfor sunk box using heavy duty stone drilling/cutter machine and making good the disturbed surface complete all as specified and directed. 132 S&F ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, hum free, AC, 230 volts, 100 watts complete all as specified & directed 133 S&F Ceiling fan complete with three blades,down rod, accessories230 V, 1200 mm sweep, min air delivery 210 CFM, BEE 5 star rated with brushless direct current motor incl connection including taking down old fan any sweep and depositing to MES store yard complete all as specified & directed. 134 S&F Exhaust fan 300 mm sweep heavy duty, steel body, AC, single phase 230 volts, 50 Hz, with blades, frame and louvers shutter with necessary hole drilling in wall and making good the disturbed surfaces incl connection including taking down old fan any sweep and depositing to MES store yard complete all as specified and directed. 135 M&L for sub main wiring with 2.5 Sqmm nominal cross sectional area, two single core, 1100 volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 2.5 Sqmm nominal cross sectional area, single core, 1100 volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit not less than of 20mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases, pinning etc in stone/ brick masonary/ walls and making good to the disturbed surfaces to match the existing complete all specified & directed. (Note : One run of earth continuity conductor, one run of PVC Conduit concealed in wall and two run of copper conductor together taken as one length for measuring unit length) 136 M&L for sub main wiring with 10.00 Sqmm nominal cross sectional area, four single core, 1100 volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 10 Sqmm nominal cross sectional area, single core, 1100 volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit not less than of 25 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases, pinning etc in stone/ brick masonary/ walls and making good to the disturbed surfaces to match the existing complete all specified & directed. (Note : One run of earth continuity conductor, one run of PVC conduit and four runs of copper conductor together taken as one length for measuring unit length) 137 Cutting chases, pinning in Stone walls/ brick walls etc.making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc, for concealed conduit wiring a into or through the stone walls built in cement mortar or cement lime mortar and walls of cement concrete suitable for housing 25mm dia conduit pipe using heavy duty stone drilling/cutter machine and making good the disturbed surface complete all specified & directed. 138 S&F Sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 12 way, with 200 Amps rated copper bus bar and double door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting / civil wk etc in wall as required complete all as specified & directed. 139 S&F MCB SPN 40/63 amps, 240 Volts, AC of breaking capacity 10 KA,C curve and connections by using suitable copper lugs complete all as specified & directed. 140 S&F MCB SP, AC, 240 volts of 06 to 32 Amps capacity c curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed. 141 ITEMS APPLICABLE FOR JOB D(B/R) :- 142 S&F for 7 feet long 4 pipes pulley operated cloth drying system consisting of aluminium pipe of outer dia 22 mm,inner dia 19.80 mm (4 Nos), made up of detrin with rope guide mounted on channel pair of length 24 feet ( distance between two pipe is adjustable) locking system to hide rope knot,channel to be mounted or fixedwith self taping screws provided in kit.Rope shall be HDPE pipe double core of 4 mm dia fixing to ceilingall as specified and as directed 143 M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished smooth and even without using extra cement complete all specified & directed. 144 M&L for rendering 10 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement complete all specified & directed. 145 M&L Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper using mechanical means over a coat of chalk whitening complete all specified & directed.
