Tender For Interior Work, Partition And Other Civil Work At Office Building Nagar Parishad Chakradharpur , Vertical Blind Premium Quality Manually Operated Vertical Blinds Of Prescribed Size With Prestressed Micro-Aerated Solar Protection Fabric Of High Tenacity Polyester Yarn With Pvc Coating &Fungistatic Treatment And Should Block The Light Flux & Offer Elimination Of Glare And Sunlight. Fabric For Blinds: Composition: 40% Polyester / 60% Pvc, Weight:400 G/M2 (+/-5%), Thickness:0.45 Mm (+/-5%), Fabric Openess Factor: 4% , Tensile Strength (Warp/Weft): 220/220 Dan / 5Cm, Tearing Strength (Warp/Weft): 30/25 Dan, Fire Retardancy:M2 (Nfp92-507)- Roller Tube Shall Be Of Extruded Aluminum Alloy 38Mm O.D (Or As Per System Dimension) With A Minimum Wall Thickness Of 1.0Mm Duly Anodized For Long Life. Clutch Shall Be Wrap Spring Design With High Strength Fiberglass Reinforced Polyester Assembly And High Carbon Steel Springs To Transmit Motion From Driving To Driven Members Of Clutch Mechanism. Clutch Shall Operate Directionally With The Use Of An Endless Beaded Chain. Clutch Mechanism Shall Be Crash Proof, Prevent Slippage And Shall Raise And Lower Smoothly To Any Desired Height. Clutch Shall Never Need Adjustment. Idler Shall Be Of High Strength Fiberglass Reinforced Polyester,Consisting Of An Outside Sleeve And Center Shaft. Sleeve Shall Provide Bearing Surface For Roller Tube And Rotate Freely On Center Shaft, Providing Smooth, Quiet And Long Wearing Operation. , Door Pining 4 X 3 Wide Bit Of 18 Mm Thick Moisture Resistant Plyboard Shall Be Used On Door Frame & Finished With 0.8 Mm Decorative High Pressure Laminated Sheet Of Plain / Wood Grain In Gloss / Matt / Suede Finish With High Density Protective Surface Layer And Reverse Side Of Adhesive Bonding Quality Conforming To Is : 2046 , Acp Partition Aluminium Partition System Having Minimum Main Frame Size Of Vertical Of 100Mm X 55Mm X 2Mm Thick And Aluminium Horizontal Minimum Size Of 75Mm X 65 X 2Mm Made Out Of Specially Designed Extruded Aluminium Sections To Withstand Support Section And Fabricated, Fixed At All Levels, Elevation And Heights To The Masonry / Rc Walls / Rc Supporting Elements With Necessary Clamps, Brackets And Anchor Fasteners. All Clamps And Brackets Shall Be Mild Steel Hot Dip Galvanized Minimum 80 Microns Thick And Shall Conform To Is: 4759-1996. The Extruded Aluminium Section Shall Be Powder Coated In Approved Colour With A Anodic Coating Of Minimum 15 Microns. Extruded Section Shall Be Of 6063 T5 Or T6 Alloy Conforming To Astm B 221. Any Other Fastening Straps, Nuts, Bolts, Rivets, Washers, Etc. Shall Be In Stainless Steel Ss 304 Grade. , Logo Shall Be Of Approved Design With 4 Mm Thick Acrylic Sheet Finished With Vinyl Coating , Cool White 15 W Led Surface Light Luminaire Class (As Per Cl. 2.1 Section 2 Of Is: 10322 (Part-1) Class I Types Of Led Modules As Per The Is: 16103(Part-2)/2012 Type 3 Photo Biological Safety Of Leds Used Shall Be As Per Is:16108/2012 (Exempt Group) Yes Dc Or Ac Supplied Electronic Control Gear For Led Module Shall Comply Is:15885 (Part 2/Sec.13) Yes Conformity To Indian Standard Is:10322-5-2(2012) Technical Parameters Type Of Fixture Square Material Pvc Color Temperature (+/-10%) 6000K Wattage 5 Watt Constructional All Fasteners Must Be Of Nickel/Chrome Plated Yes The Luminaire Body Must Be Corrosion Resistant Epoxy Powder Coated / Anodizing Yes Mounting Type Surface Diffuser Material Poly Carbonate (Uv Stabilized) Mounting Fixture Ss Spring Clip Ingress Protection (Ip Rating) As Per Is:10322 (Part 1) Latest Ip20 Electrical Efficiency Management The Total Circuit Power Shall Not Be More Than 110 Percent Of The Value Declared By The Manufacturer (As Per Cl 8 Of Is:16104:2012 Lates) Yes Total Harmonics Distortion 15% Frequency 50 Hertz Ac Power Factor 0.95 Operating Voltage 230 Volt Driver Independent Optical Management Light Color Warm White Reflector Type Diffuser System Lumen Output 900 Lumen System Luminous Flux Efficacy (Lm/W) 100 Brand Any Approved Brand As Per Buyer Requirement , Inverter Set Model (Electric) Optimus 2300 Pure Sine Wave 2000Va/24V Inverter With Red Charge Rc18000 Tall Tabular 150Ah Battery - 2 Batteries Inverter Details- Type: Pure Sine Wave ; Va Rating: 2000Va/24V; Supports: Double Battery Each Of 12 Volt; Peak Load: 1600W; Output Voltage : 220V (Inverter Mode) Battery Details- Type: Tall Tubular Battery; Construction: Rugged, Rated Capacity: 150 Ah/12V, Water Level Indicators: 6 Informative Lcd Display : Smart Lcd Display With Unique Indication That Displays Backup And Charging Time, Along With Mains On, Eco/Ups Mode; Super Fast Battery Charging : Maximum Charging Current 21A For The Faster Battery Charging Inverter Dimensions: 30X32.6X28.4 Cm Battery Dimensions: 50.2 X 19.1 X 44.0 Cm Material: Metal & Plastic Brand: Any Approved Brand As Per Buyer Requirement , Sound Syetem In Conference Hall Ceiling Speaker Ahuja - 8 Nos. Cma 5400 Amplifier - 1 Nos. Cmd 5100 Mike - 1 Nos. Cmc 5200 Mike - 25 Nos. Speaker Wire - 200 Mtr Ceiling Speaker 10 W - 8 Nos Input Power 10W Rms Power Taps On 100V 10/5/2.5W Impedance 1K/2K/4K? Frequency Response 60-15,000Hz Special At 1Khz (1W/1M) 92Db Dimensions Ø204 × H79 Mm Weight 0.89Kg Central Mixer Amplifier - 1 Nos Line Output 1 17.5V Dc/3A Max.; -34Dbv (20Mv) Line Output 2 17.5V Dc/3A Max.; -34Dbv (20Mv) Power Output 50W Rms At 2% Thd, 90W Max.Inputs 3×Mic 0.65Mv/4.7K?, 1×Aux 100Mv/470K? Frequency Response 60-14,000Hz (± 3Db) S/N Ratio 60Db Tone Controls Bass: -10Db At 100Hz, Treble: -10Db At 10Khz Preamp Output 200Mv/600O Line Output 1V/1K? Send Output 200Mv/600O Return Input 200Mv/10K? Speaker Output 4O, 8O, 16O, 70V & 100V Power Requirement Ac: 220-240V, 50/60Hz, Dc: 24V (2×12V Car Battery) Power Consumption 250Va Protections Ac Fuse 1×3 Annual Periodical Maintenance , Dc Fuse 2×10 Amp.Dimensions W483 × H110× D325 Mm Weight 10.50Kg Mike For Principle Authority - 1 Nos Microphone -63Dbv/?Bar (7.5Mv/Pa) Current Consumption 50Ma Max. Mic Auto Switch-Off Time 75 Seconds Approx. Input Line Output Line, Headphone Speaker Max Input 300Mw Controls Priority Switch, Talk Switch, Speaker Volume Control, Headphone Volume Control Dimensions W118 × H70 × D160 Mm Weight 1.05 Kg (W/O Cable) Accessories Foam Windshield, 2.5M Interconnecting Cable Mike For Delegate - 25 Nos Microphone -63Dbv/?Bar (7.5Mv/Pa) Current Consumption 50Ma Max. Mic Auto Switch-Off Time 75 Seconds Approx. Input Line Output Line, Headphone Speaker Max Input 300Mw Controls Talk Switch, Speaker Volume Control, Headphone Volume Control Dimensions W118 × H70 × D160 Mm Weight 1.05 Kg (W/O Cable) Accessories Foam Windshield, 2.5M Interconnecting Cable Speaker Wire Packaging Type Coil Temperature Range Processing And Operating , Deg C (-30 To +80 ) Colour Code Transparent Warranty 1 Year Size (Awg) 20 Width 6 Millimeter Conductors Material Tinned Copper Insulation Material Pvc Thickness 0.7 Millimeter Size (Square Mm) 0.5 Number Of Conductors 2 Power Loss In % 33 Height 2.5 Millimeter Conductor Resistance (Ohms/Km 20 C )(Max) 33 Brand Any Approved Brand Like Ahuja Or Equivalent , Supply, Installation, Testing & Commissioning Of 62 Kva Diesel Generator Set With Amf Panel.Brief Description Of The Equipment Shall Be As Follows:-Diesel Engine Engine Shall Conform To Relevant Is/Bs Specifications And Be Complete With Heat Exchanger, Reciprocating Pump And Cooling Water Pump, Oil Pump,Diesel (Fuel) Tank, Selfstartingmotor, Batteries Of Adequate Ampere Hourcapacity For Self-Starting And To Give At Least Threeattempts At One Time. The Engine Shall Be Capable Of Developing Required Hp At Site Conditions And At 1500Rpm Continuous Duty. Speed Regulation Shall Be Such Thatfrom No Load To Full Load, The Variation In Speed Isminimum, Say Within 5%. Alternator - The Alternator Shall Conform To Is 4722 And Iec 34-1 And Shall Be Of Salient Stationary Pole Revolvingarmature Self-Excited Self Compensated Type Anddesigned For 415 Volts, 50 Hz, 3 Phase Output At 1500Rpm Capacity Of 160 Kva At 0.8 Providing Fixing Lag, At Site Condition.The Voltage Regulation Shall Not Be More Than 5% Over The Full Load Range Including The 5% Speed Regulation Ofprime Mover. The Alternator Shall Be Directlycoupled Tothe Diesel Engine Through Flexible Coupling. The Designshall Be Such That The Harmonics Are Minimum. Thepower Supply Terminals Including The Neutral Shall Bebrought Out In A Suitable Cable Entry Box As Directed.Acoustic Enclosure - The Generating Sets Are Housedinside Ahigh Quality Acoustic Enclosure Having Salient Features & Constructional Features Such As • Compact, Modular Construction And Sleek Design With Lownoise Level (75 Dba) At A Distance Of 1 Meter In Openenvironment.• Soundproof, Weatherproof, And Environment Friendlysilent Set.• The Acoustic Enclosure Is Manufactured, Powder Coated And Lined With Fire Proof Acoustic Material Light Resin Rockwool As Per International Standards & Meeting Latest Cpcb/Local Pcb Norms.• Made Out Of 1.5 To 2 Mm Thick Crca Sheet, Compactsleek Design Confirming To International Standards & Meeting Cpcb/ Local Pcb Norms.• Exhaust Silencer To Be Of Residential Grade Typemounted Outside The Enclosure, Exhausting Toatmosphere.Micro-Processor Based Amf Control Panel: - The Microprocessor Based Control Panel Shall Be Designed Forautomatic On Mains Failure Operation Of The Generatorset. The Panel Shall Be Floor Standing Cubicle Pattern,Fabricated Out Of 14 & 16 Swg. M.S. Sheet And Painted With Powder Coated Of Approved Quality Shade Withappropriate Ventilating Arrangement. The Panel Shall Be Complete With The Inter Connections, Insulators 2Numbers Earthling Plug And Shall Incorporate The Following: Selector Switch Voltmeter - Off/Ry/Yb/Brammeter 0-100 A Selector Switch Ammeter - Off/R/Y/Bvoltmeter 0-600 Vfrequency Meter (Digital)Set Of Current Transformer Of Suitable Ratio Built-In Smps Charger Or Boost Cum Trickle Battery Charger Consisting Of- (A) Transformer/Rectifier (B) Dc Ammeter (C) Dc Voltmeter (D) Charging Rate Selector Switch Set Of Led Lamps For Start Failure, High Temperature Trip, Protection For Ac Generator Main Supply Voltage Monitor With Under/Over Voltage Adjustable Setting. Set Of Control Relays Set Of Indicating Lamp Load On Set, Load On Mains, Start Failure,High Temperature Trip, Low Oilpressure, High Temperature Warning, Battery Low.Push Buttons For Start, Stop, Reset/Alarm Acknowledge/Dg/Mains Supply Contractors Close/Open And Test Toggle Switch For Hooter On/Off 3 Phase 4 Wire Unbalanced Type , External Logo As Per Approved Design Of Size 885 Mmx 750 Mm Made Up Of Acrylic Material. , Projector With Screen Technology Lcd Projection Method Front And Rear Both Native Resolution 1920 X 1080 (Full Hd) Brightness (Lumens) 4000 Contrast Ratio (Minimum) (Pixels )( X :1) 1000 Optical Zoom Yes If Yes, Optical Zoom (%) 135 Availability Of Lensyes Remotely Controlled Ye If Yes, Type Of Projector Long Throw (Above 2.5) Aspect Ratio 16:09 Keystone Correction Automatic & Manual Both Type Of Light Source Led Minimum Life Of Light Source (In Normal Mode) (Hours)30000 Lamp Hour Counter (In-Built) Yes Inbuilt Speakeryes If Yes, Wattage Of Speaker2 3D Projection Capabilityno Interactive Featureyes Power Consumption In Sleep Mode (Watts)327 Power Consumption In Normal Mode (Watt) 3 Noise Level In Echo Mode (Db)35 Noise Level In Normal Mode (Db)34 Power Supply 210V-240V, 50 Hz Dimensions (Length X Breadth X Height) (Mm X Mm X Mm) 325 X 240 X 106 Mm Weight (Kg) 2.5 Minimum Operating Temperature (Degree C) -18 Maximum Operating Temperature (Degree C) 36 Minimum Operating Humidity ( % Rh) 10 Maximum Operating Humidity ( % Rh) 65 Ports & Connectivity Number Of Hdmi In Port 2 Number Of Hdmi Out Port 2 Audio In Yes Audio Out Yes Video In Yes Storage Media Port Yes If Yes, Supported File Formats Mpeg -1,Mpeg-2,Dvd-Lpcm Number Of Usb Type A 1 Number Of Usb Type B 1 Wi Fi Connectivity Yes Wireless Screen Share Yes Lan Connectivity Yes Brand Any Approved Brand Like Hp, Dell Or Equivalent Screen Is Made Up Of 18 Mm Thick Moisture Resistant Plyboard & Finished With 0.8 Mm Decorative High Pressure Laminated Sheet Of Plain Grain In Gloss / Matt / Suede Finish With High Density Protective Surface Layer And Reverse Side Of Adhesive Bonding Quality Conforming To Is : 2046 , Ptz Camera , Electric Podium , Integrative Panel For Conference Hall , Wood Flooring 25 Mm Wooden Planking, Tongued And Grooved In Flooring, Including Fixing With Iron Screws Complete With Second Class Teak Wood , False Ceiling Providing 12Mm. Flat Pressed Particles Board Ceiling With Ceiling With 120X60mm. Sal Wood Beams At 122Cm. Centers And 60X40mm . Sal Wood Runners At 122Cm Centers Including Cost Of 2 Coats Of Wood Preservative Paint Of Approved Make, Fixing At Site And Taxes All Complete As Per Approved Drawing, Building Specification And Direction Of E/I. , Wall Panelling Providing Wall Panelling Witn 3.5Mm Thick Teak Veneered Decorative Ply Wood: Of Standard Make. Fitted And Fixed Over, 50X12mm Sal Wood Beads At 122Mm Centres Properly Screwed To Walls Including Cost Of Spirit Polishing Over Ply Wood And 2 Coals Of Wood Preservative Paint Over The Beads Of Approved Shade And Make All Complete As Per Specification And Directionofe/I , Wall Painting Providing Two Coats Of Plastic Emulsion Paint Of Approved Shade_And Make Over A Coat Of Cement Primer Over New Surface Including Preparing Plastered Surface By Rubbing Smooth With Pumice Stone Or Fine Sand Paper, Applying Putty Wherever Required, Scaffolding Do-
