|
| 1 | S&F in repair PVC connections 450 mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and as directed. |
| 2 | S&F in repairwaste fittings, 32/40 mm brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and as directed. |
| 3 | S&F in repairPVC waste pipe 32/40 For WHB and sink, complete all as specified and as directed. |
| 4 | S&F in repair 15 mm angle valve/ stop valves, cast copper alloy , chromium plated, fancy type screwed down high pressure with crutch and butter fly handles , screwedwithiron pipes or for union, complete all as specified and as directed. |
| 5 | S&F in repairbib tap brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore, complete all as specified and as directed. |
| 6 | S&F in repair15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts,screwed for iron pipe and fixed, complete all as specified and as directed. |
| 7 | S&F in repairmixing valve 15 mm dia, CP brass fancy including joints to steel pipe or unions for centre hole wash hand basin, including fittings, complete all as specified and as directed. |
| 8 | S&F in repairgrating with 100mm dia of PTMT approved make including fixing with 1:4 CM to floor/ nahni trap etc., complete all as specified and as directed. |
| 9 | S&F in repairgrating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) etc., complete all as specified and as directed. |
| 10 | S&F in repair brass chromium plated overhead shower rose 125mm dia, with revolving joint and shower rod to fixed to 15mm bore pipe, complete all as specified and as directed. |
| 11 | S&F in repair health faucet chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. |
| 12 | S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. |
| 13 | S&F in repair PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and PVC flush pipe 32 mm dia for low level, complete all as specified and as directed. |
| 14 | S&F in repair 32mm brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. |
| 15 | S&F in repair 40mm brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. |
| 16 | S&F in repair brass chromium plated tubular towel rail, 20mm dia, \"D\" type 60cm long between flanges of brass CP, complete all as specified and as directed. |
| 17 | Taking down and refixing in same opening after resecuring, easing and adjustingof Shutters (wooden/glass) of any description exc 1 Sqm and n exc 2 sqm each complete all as specified and as directed. |
| 18 | Taking down and refixing in same opening after resecuring, easing and adjusting of Shutters (wooden/glass) of any description exc 2 Sqm each complete all as specified and as directed. |
| 19 | Resecuring, easing and adjusting with out taking down of Shutters (wooden/glass) of any description n exc 1 Sqm each complete all as specified and as directed. |
| 20 | Resecuring, easing and adjusting with out taking down of Shutters (wooden/glass) of any description exc 1 Sqm and n exc 2 sqm each complete all as specified and as directed. |
| 21 | Resecuring, easing and adjusting with out taking down of Shutters (wooden/glass) of any description exc 2 Sqm each complete all as specified and as directed. |
| 22 | S&F in repair sliding door bolt, 300 mm long,with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections or cast aluminium alloy cincluding a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed. |
| 23 | S&F in repair MS butt hinges 100 mm size, cold rolled, medium weightfixed with screws to wooden frames or welding to steelframes etc complete all as specified and as directed. |
| 24 | S&F in repair extruded aluminium alloy handles, fabricated type, anodised, 150 mm size complete all as specified and directed |
| 25 | S&F in repair aluminium anodized barrel tower bolts of extruded section length of bolt 200mm long complete all as specified and directed. |
| 26 | S&F in repair door closer hydraulically regulated universal type,sutiable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg of extruded aluminium section designation No-3complete all as directed. |
| 27 | Taking down and refixing in same opening toughned glass door 10/12 mm thick including all necessary fitting including floor spring,S/S bracket,lock& S/S handle etccomplete all as specified and as directed. |
| 28 | Taking down shutters of any description n exc 1 sqm each complete all as specified and as directed. |
| 29 | Taking down shutters of any description but exc 1 sqm and n exc 2 sqm each complete all as specified and as directed. |
| 30 | Taking down shutters of any description but exc 2 sqm each complete all as specified and as directed. |
| 31 | Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames), complete all as specified and as directed. |
| 32 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 33 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick with edge lipoping tape allaround 0.8mm thick, comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. |
| 34 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type gauzed door shutter of size 30 mm thick with edge lipoping tape allaround 0.8mm thick, comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,SS wire cloth complete all as specified and as directed. |
| 35 | S&F 125 mm long SS butt hinges including welding in existing MS frame complete all as specified and as directed. |
| 36 | S&F 15 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid floors or concealed, including taking up or down steel tubing and connections including cleaning for re-fixing, 15 mm bore of pipe, complete all as specified and as directed. |
| 37 | Supplying and laying of CPVC pipes 16mm SDR 11 & Plain CPVC SDR 11 including brass & plain CPVC fittings on walls/ceiling or laying in floorsincluding taking up or down steel tubing and connections 15 mm bore of pipe, complete all as specified and as directed. |
| 38 | S&F 20 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid floors or concealed, including taking up or down steel tubing and connections 20mm bore of pipe, complete all as specified and as directed. |
| 39 | Supplying and laying of CPVC pipes 20mm SDR 11 & Plain CPVC SDR 11 including brass & plain CPVC fittings on walls/ceiling or laying in floorscomplete including all fitting as required at site like elbow,socket,tee etcincluding taking up or down steel tubing and connections 20mm bore of pipe, complete all as specified and as directed. |
| 40 | M & L for cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; andcutting chases for concealed watertubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and as directed. |
| 41 | S&F in repair stainless steel sinks without drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420 mm, andbowl size 410mm x 330mm x 160mm, complete all as specified and as directed. |
| 42 | S&F in repair vitreous china wash down water closet pan (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device, complete all as specified and as directed. |
| 43 | S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and as directed. |
| 44 | S&F in repair vitreous china wash basin, white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified and as directed. |
| 45 | S&F in repair stainless steel wire cloth, 0.63 mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to doors/ steel windows, complete all as specified and as directed. |
| 46 | M&L for welding in repairs exceeding 2.5 cm but not exceeding 5.0 cm in length thickness of metal be welded exc 6 mm but n. exc 9 mm, complete all as specified and as directed. |
| 47 | S&F 4 mm thick sheet glass ordinary quality n.exc 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc including hacking out old broken glass (any thickness size and quality and description) from wooden/steel frames glazed with putty or fixed with beads etccomplete all as specified and as directed. |
| 48 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and including taking down old shutter and refixing in same opening after replacing floor springcomplete all as specified and as directed. |
| 49 | S&F in repair 600x450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooded plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 50 | M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 51 | M&L for light shade vitrified ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 52 | M&L for dark shade vitrified ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 53 | M&L for light shade vitrified ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 54 | M&L for dark shde vitrified ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 55 | M&L for joint free glazed ceramic coloured tiles in vertical surface 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, over and includingbacking coat/ plaster 10 mm thick on fair faces of brick work in CM 1:4 surfaces to receive tiles, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 56 | Taking down cement or cement lime plaster, any description, on brick or stone walls, concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by engineer-in-charge. |
| 57 | M&L for 15 mm thick plaster with ready mix plaster finished even and smooth plaster up to G+5 Building including necessary scaffolding complete all as specified and as directed. |
| 58 | M&L for 5mm thick ready mix plaster on concrete surfaces of ceiling, chajja,etc finished even and smooth, complete all as specified and directed by engineer-in-charge. |
| 59 | M&L for 10 mm thick plaster with ready mix plaster finished even and smooth plaster up to G+5 Building including necessary scaffolding complete all as specified and as directed. |
| 60 | M&L for preparation un decorated plastered surface and applying two coats of Tractor Suprema Acrylic Distemper with Graco spray machine over a coat of wall care putty complete all as specified and as directed. |
| 61 | M&L for complete removal of existing treatment and preparationplastered surface and applying two coats of Acrylic Distemper with Graco spray machine over a coat of wall care putty 1 mm thick complete all as specified and directed. |
| 62 | M&L preparation undecorated plastered surface and applying two coats with Graco-490 spray machine, of GreenPro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6sqm/ltr over a coat of 1mm thick waterproof putty including scaffolding up to G+3 complete all as specified and directed. Note :Application to be done only by applicator authorised by manufacturer also shall be approved by GE before starting of work. |
| 63 | M&L for complete removal of existing treatment from external surface and preparation undecorated plastered surface and applying two coats with Graco-490 spray machine, of GreenPro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6sqm/ltr over a coat of water proof putty including scaffolding up to G+3 complete all as specified and directed.Note :Application to be done only by applicator authorised by manufacturer also shall be approved by GE before starting of work. |
| 64 | M&L for preparation of newly plasered surfaces of ceiling and applying two coat of white wash over a coat of alkali resistant primer, complete all as specified and as directed. |
| 65 | M&L for preparation of old surface of ceiling and applying one coats of white wash, complete all as specified and as directed. |
| 66 | M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint, complete all as specified and as directed. |
| 67 | M&L for preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint, complete all as specified and as directed. |
| 68 | M&L for brick work with sub class \"B\" bricks, straight or curvedon plan exceeding 6 m mean radius built in CM 1:6, including demolition of brick work built in cement mortar or cement lime mortar, complete all as specified and as directed. |
| 69 | Cutting of vegetable plant (girth not exceeding 300mm) from roof, terrace, chajjas etc digging out the roots and making good the surface in PCC 1:2:4 type B1 with surfaces finished to match complete including scaffolding etc, complete all as specified and as directed. |
| 70 | S&F 500 ltr capacity tripple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, including dismantling of water tanks of capacity500 litres, complete all as specified and as directed. |
| 71 | S&F 1000 ltr capacity tripple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, including dismantling of water tanks of capacity1000 litres, complete all as specified and as directed. |
| 72 | S&F 2000 ltr capacity tripple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, including dismantling of water tanks of capacity2000 litres, complete all as specified and as directed. |
| 73 | S&F ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20/25 mm bore and fixed, complete all as specified and as directed. |
| 74 | S&F in repair gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20/ 25 mm bore, complete all as specified and as directed. |
| 75 | Demolition of reinforcementConcrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) demolition, (reinforcement cut as required to facilitate demolition) complete all as specified and as directed. |
| 76 | M&L for RCC 1:2:4 (Nominal Mix) typeB-0 using 12.5 mm graded crushed stone aggregate as in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like, complete all as specified and as directed. |
| 77 | M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including muld seel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed. |
| 78 | All as per item no77.00 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, complete all as specified and directed. |
| 79 | M&L for from work to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter, complete all as specified and as directed. |
| 80 | S&F stainless steel butt hinges, size 100 mm complete, complete all as specified and as directed. |
| 81 | S&F stainless steel barrel tower bolts, 150 mm long, complete all as specified and as directed. |
| 82 | S&F stainless steel handles, 150 mm long, complete all as specified and as directed. |
| 83 | M&L for SS railing buffing with sand paper with mechanincal means including cleaning of surface with soap and a clean sponge /brush, preparation of surface to make the railing to its original finish all as specified and as directed. |
| 84 | S&F in repairSteel rolling shutters of 1.25 mm thick , including ball bearing and safety lever lock, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type all as specified and directed. |
| 85 | S&F Sheet glass, ordinary quality and glazing with oil putty in square each pane of 4.8-5 mm thickness including hacking out old broken glass (any thickness ,size,quality or description) from metal frame including punching out or drilling out old glazing pin/clipsall as specified and directed. |
| 86 | Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed. |
| 87 | M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 88 | S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 89 | M&L for preparation of undecorated steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coat of synthetic enamel paint over a coat of red oxide zinc chrom primer complete all as specified and directed. |
| 90 | S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specifiedand as directed. |
| 91 | S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specifiedand as directed. |
| 92 | S&F 2 mm thick fibre glass reinforced translucent/coloured plain sheeting with side lap fixed with coach screw and washer in roof, wall etc including dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specifiedand as directed. |
| 93 | S& F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed. |
| 94 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and webof 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including 4 mmNon asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws in ceiling including dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 95 | S & F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame including dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover filletsas per specification and drawing complete all as specified and as directed. |
| 96 | Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 97 | M&L 4 to 6 mm thick ACP(aluminium composite panel) plain/wood grain finish fixed with screws under or above kitchen plateform and cup boards including Aluminium frame work,locking arragementand all fitting including dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 98 | S & FPVC magnetic catches 40 mm complete all as specified and as directed. |
| 99 | S&F in repair Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc fitting complete all as specified and as directed. |
| 100 | S&F stainless steel 25 mm dia (minimum wall thickness 1.00 mm) of approved quality curtain rod with two numbers stainless stell brackets/hook (either wall to wall or else) as per approved quality and diesign (for each 01 mtr of rod) fixed in brick/concrete wall and same finished knobs on each end of each piece of curtain rodcomplete all as specified and directed. |
| 101 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. |
| 102 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. |
| 103 | S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 104 | S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed. |
| 105 | S&F in repair 40 mm continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed. |
| 106 | S&F in repair 100 mm mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and as directed. |
| 107 | S&F in repair 150 mm mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and as directed. |
| 108 | S& F in repair 100 mm mild steel, semi-barrel tower bolt, open cover, with sheet pressed barrel, stove enamelledblack with bright bolt complete all as specified and as directed. |
| 109 | S& F in repair 150 mm mild steel, semi-barrel tower bolt, open cover, with sheet pressed barrel, stove enamelledblack with bright bolt complete all as specified and as directed. |
| 110 | S&F in repair 100 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed. |
| 111 | S&F in repair 150 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed. |
| 112 | S&F in repair 300mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. |
| 113 | S&F in repair 300 mm aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 114 | S&F in repair300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 115 | S&F in repair 100mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed. |
| 116 | S&F in repair 150mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed. |
| 117 | S&F in repair 100 mm aluminium handles, cast type, anodised complete all as specified and as directed. |
| 118 | S&F in repair150 mm aluminium handles, cast type, anodised complete all as specified and as directed. |
| 119 | S&F in repairMS mortice lock(4 lever), vertical type, size 100 mm complete all as specified and as directed. |
| 120 | S&F in repair brass mortice lock(4 lever), vertical type, size 100 mm complete all as specified and as directed. |
| 121 | S&F in repair brass knobs 35-40mm dia complete all as specified and as directed. |
| 122 | Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 123 | M&L for 75 mm thick Cement concrete type D- 2, 1:4:8 (40 mm graded crushed stone aggregate) as in flooring sub base complete all as specified and as directed. |
| 124 | M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer throughvibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed. |
| 125 | M&L for 18-20 mm thick granite work (of any type) (table rubbed and polished) as in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in cement mortar1:6, including Dismantling stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar, aprons etc complete all as specified and as directed. |
| 126 | M&L for kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over and including screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in cement mortar 1:6, including Dismantling stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar, aprons etc complete all as specified and as directed. |
| 127 | M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 128 | Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar complete all as specified and as directed. |
| 129 | Demolition of cement concrete in of any description and in any position, complete all as specified and as directed. |
| 130 | M&L for cement concrete type B0(1:2:4), using 12.50 mm graded stone aggregate, of average thickness 25 mm, as in roof padding alongwith liquid water proffing compound, complete all as specified and as directed. Note: liquid water proofing compound shall be paid and measured seperately. |
| 131 | M&L for cement concrete type B1 (1:2:4), using 20mm graded stone aggregate as in roof kerbs or mud stop rounded or chamfered on edge etc., complete all as specified and as directed. |
| 132 | M&L for screed bed or bedding layer of mortar15 mm thick for laying floor finishes in cement mortar 1:4, mixed with water proofing compound complete all as specified and as directed.(water proofing compound shall be paid seperately) |
| 133 | Supply only liquid water proofing compound, complete all as specified and as directed. |
| 134 | M & L for APP based polymeric water proofing membrane minimum weighing not less than 3.5 Kg/sqm and 3mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm laid over and including applying evenly primer by torch application including cleaning of surface complete all as per approved manufacturer\"s instructions. complete all as specified and directed by Engineer-in-Charge.Note:-The water proofing treatment shall be carried out by manufacturer or their auth applicators as per manufactures instruction and as directed by Engr in Charge. |
| 135 | M & L for preparation of undecorated plastered surfaces and applying one coat of heat resisting paint over a coat of priming paints on APP membrane complete all as specified and as directed. |
| 136 | S&F 75mmPVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in wall including all fitting and stack clamp (50mmx5mm flat iron and 16mm dia round iron stays) as site requirement including breaking up 75mm diadrain pipes (PVC drain pipe) laid in trenchs /wall complete all as specified and as directed. |
| 137 | S&F 110 mmPVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in wall including all fitting and stack clamp (50mmx5mm flat iron and 16mm dia round iron stays) as site requirement including breaking up 110/75mm diadrain pipes (PVC drain pipe) laid in trenchs /wall complete all as specified and as directed. |
