Tender For Additional / Alternator Cum Special Repair To Ocs Toilet & Allied Works At Ota Gaya.; 2 Item No 01 : Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing from the site. 3 Item No 02 : Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for and removing from the site. 4 Item No 03 : Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 5 Item No 04 : Taking down cement plaster on brick or stone walls etc, including racking out joints, hacking for key, scrubbing down with water etc. 6 Item No 05 : Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. 7 Item No 06 : Taking down chowkhats or frames not exc 1.5 Sqm each (without taking shutters from the frame) complete all as specified and directed. 8 Item No 07 : Taking down chowkhats or frames exc 1.5 Sqm but n exc 4.0 Sqm each (without taking shutters from the frame) complete all as specified and directed. 9 Item No 08 : M & L for providing cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate as incoping and the like including weathering, slightly rounded or chamfered angles and throating complete with using WPC. 10 Item No 09 : M & L for providing 75 mm thick cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection and simillar works finished even and smooth without using extra cement complete.Note: Joints 12 mm wide to the full depth of PCC shall be provided at every 3 m and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provn shall be deemed to be included in the quoted rate. 11 Item No 10 : M & L for providing 25 mm thick cement concrete type B-0, 1 : 2 : 4 using 12.50 mm graded stone aggregate as inflooring, sub-base complete with using WPC. 12 Item No 11 : M & Lreinforced cement concrete (nominal Mix) 1:2:4 type B1 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete. 13 Item No 12 : Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finsished surfaces of concrete complete. 14 Item No 13 : M&L for mild steel TMT bars 10mm dia and over cut to lengh bent to shape required incl cranking bending spirally for hooping for columns hooking ends and binding with and incl ms wire not less than 0.9mm dia complete. 15 Item No 14 : M & L for brick work using fly ash old size bricks straightor curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed. 16 Item No 15 : M & L for brick work using fly ash old size bricks in half brick thick wall, straight or curved on plan exc 6m mean radius built in CM 1:4 complete. 17 Item No 16 : M & L for rendering 15mm thick internal surfaces on fair faces of brick or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement) complete. 18 Item No 17 : M & L for rendering 15mm thick in two layers (10mm and 5mm) on fair faces of brick or concrete surfaces in cement plaster 1:4 using WPC 3% by weight of cement or as per manufacturers instruction (WPC to be measured and paid separately) and finished even and smooth (without using extra cement) complete. 19 Item No 18 : M & L for rendering 10mm thick in ceiling surfaces in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed. 20 Item No 19 : Supply Only integral water proofing compound 21 Item No 20 : Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete. 22 Item No 21 : M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match overand including 15 mm thick screed bed in CM 1:6 complete. 23 Item No 22 : M & L for coloured glazed ceramic tiles in vertical surface 7mm thick350x 250x 7mm/ 450X 350X 7mm, set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10mm thick rendering in cement mortar 1:4as backing for tiles complete all as specified and as directed. 24 Item No 23 : M & L for providing 75mm thick PCC 1:3:6, type C-1, (using 20 mm graded aggregate) as sub base flooring complete and finishing surfaces even and smooth without using extra cement complete. 25 Item No 24 : M & L for machine pressed cement concrete chequered tiles coloured glossy type, lacuered finish 300 x 300 x 25 mm thick with grey cement and pigmentover and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed. 26 Item No 25 : M & L for sand filling under floor or in foundations including watering and consolidation complete all as specified and directed. 27 Item No 26 : M & L for machine pressed precast concrete interlocking paver block coloured rubber moulded, lacuered finish any shape and sizewith grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed. 28 Item No 27 : M & L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete. 29 Item No 28 : M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:6 complete. 30 Item No 29 : M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and polishing complete over and including 10mm thick rendering in Cement Mortar 1:4 complete. 31 Item No 30 : S & F Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete. 32 Item No 31 : S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. 33 Item No 32 : S & F aluminium handle cast type anodized 150mm size complete. 34 Item No 33 : S & F aluminium anodisedbarrel tower bolts of extruded section 200mm long 35 Item No 34 : S & F 100mmstainless steel Butthinges heavy wt cost iron and fixed complete. 36 Item No 35 : S & F stainless steelsliding door bolt with hasp & staple (Bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy size 300mm long. 37 Item No 36 : S & F Aluminium partition, frame/shutters for windows, ventilators sliding/ openable etc icluding joining cleat for fixing, locking arrangement, rubber beading, screwscomplete all as specified.Note : (i) Glazing and wire mesh shall be measured and paid separetely only as the labour element included in the relavent item.(ii) Item shall be paid as per weight of aluminium section (iii)The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin, screws and powder coated fittings such as locking arraangement etc as required, which shall not be measured for arriving the weight (iv) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing. 38 Item No 37 : Supply & fix stainless steel wire cloth. 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete. 39 Item No 38 : Supply & fix 4 mm thick Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane complete. 40 Item No 39 : S & F 4mm thick aluminium composite panel in aluminium frame work complete all as specified and directed. 41 Item No 40 : M & L for applying a thin layer of 1.0mm thick white wall care putty over newly plastered surface toprepare the surface even and smooth complete all as specified and directed. 42 Item No 41 : M & L for preparation of new plasteredsurfaces and applying two coat of oil bound distemper on walls complete all as specified and as directed. 43 Item No 42 :M & L for preparation of new plasteredsurfaces and applying two coat of oil bound distemper in ceilings complete all as specified and as directed. 44 Item No 43 : M & L for preparation of new plastered/decoarated wall surfaces and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. 45 Item No 44 : M & L for providing water proofing treatment over cleaned roof surface with super thermo APP modified polymeric membrane comprising of followings :- (i). Complete removal of existing roof treatment by picking, sweeping clean and washing down with water to remove dust etc from plastered / roof surface / walls and filling the crackes with sealing compound grade A .(ii) Rendering / screed bed 15 mm thick in cement mortor (1:4) mixed with liquid water proofing compound as per manufacturers instructions andfinished the surface fair and even. (iii) Applying evenly a coat of bitumen based primer conforming to IS-3384-1965 @ 0.30 Kg/Sqm.(iv) Applying 3 mm thick APP modified polymeric membrane with non polyster reinforcement of approved make, weight not less than 3.50 Kg/Sqm laid with gas torch and fastedon roof surface with roller. The over laps 100mm and shall be sealed by torch application as per manufacture instructions including vertical surfaces after cutting necessary grooving and making good with PCC 1:2:4 type B-O with sika latex power as per manufacture instructions.(v) Applying two coats of bituminous anticorrosive multi purposealuminium coating (super silver shield) @ 150 gm/sqm per coat over polymeric membrene. Note :- WPC shall be measured and paid separately. 46 Item No 45 : Dismantling of existing sunken treatment including plaster and M & L for water proofing treatment on existing sunken portion with the following specification complete all as specified and directed :-(a) 15 mm thick (average) plaster on sunken floor in CM (1:4) with waterproofing compound as per manufacturer instruction complete all as specified & directed . (b) Apply bituminous primer @0.50 Kkg/Sqm conforming to IS 3384-1965 on prepared surface till the surface is properly impregnated.(c) Apply hot bitumen 85/25 grade @ 1.20 kgs/sqm confirming to IS 702-1988. (d) Laying polymeric water proofing memberae weight not less than 3.0 kgs/sqm as per manufacturer instructions confirming to IS. (e) Apply layer of blown grade bitumen 85/25 @ 1.2 Kgs/Sqm confirming to IS.(f) One spout of 40 mm GI pipe shall be provided in sunken floor and sunken porion shall be filled with lean concrete Type E-2 (1:5:10) using brick aggregate complete. 47 Item No 46 : Dismantling structural steel work including doors, gates, grills but excluding framed truss etc complete. 48 Item No 47 : S & F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 49 Item No 48 : S & F of 1000 ltrs capacity white rotational Moulded ploythene water storage tanks (cylinderical vertical with closed top) three layered hoisted and fixed in position incl dismantling of existing tanks. 50 Item No 49 : M & L Ball brass valves 25 mm, high pressure, with polythene float and flynut incl tank nipple connection for float valve complete, screwed for iron pipe or brass ferrule and fixed 51 Item No 50 : S & F in repair 25mm dia bore CPVC gate valves with handle or wheel head, screwed both ends for pipe and fixed. 52 Item No 51 : S & F in repair 20mm dia bore CPVC gate valves with handle or wheel head, screwed both ends for pipe and fixed. 53 Item No 52 : S & F in repairs CPVC pipes 20 mm outer dia SDR 11 & Plain CPVC SDR 11 includig all fittings on walls/ceiling or laying in floors and taking down steel tubing and connections,including cleaning for refixing or removal to storecomplete. 54 Item No 53 : S & F in repairs CPVC pipes 25 mm outer dia SDR 11 & Plain CPVC SDR 11includig all fittings on walls/ceiling or laying in floors and taking down steel tubing and connections,including cleaning for refixing or removal to store complete. 55 Item No 54 : S & F in repairs CPVC pipes 32 mm outer dia SDR 11 & Plain CPVC SDR 11includig all fittings on walls/ceiling or laying in floorsand taking down steel tubing and connections,including cleaning for refixing or removal to store complete. 56 Item No 55 :S & F of 20mm dia Male Brass Threaded Adaptor (MTA/ MBTA)or Female Brass Threaded Adaptor (FTA/ FBTA) complete. 57 Item No 56 : S & F of 25mm dia Male Brass Threaded Adaptor (MTA/ MBTA)or Female Brass Threaded Adaptor (FTA/ FBTA) complete. 58 Item No 57 : S & F of 32 mm dia Male Brass Threaded Adaptor (MTA/ MBTA)or Female Brass Threaded Adaptor (FTA/ FBTA) complete. 59 Item No 58 : S & F in repair Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, but excuding flushing cistern and flush pipe complete all as specified and directed. 60 Item No 59 : S & F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete. 61 Item No 60 : S & F as in repair of white soft closing seat cover for pedestal pattern water closet including fixing bolts complete. 62 Item No 61 : S & F in repair brass chromium plated health faucet 15 mm with flexible tube (1.5 m long) of stainless steel provided rubber hose and wall hook etccomplete all as specified and directed. 63 Item No 62 : S&F in repair 15 mm dia two way bib taps, cast copper alloy,fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions 64 Item No 63 : Supply & fix in repair brass chromium plated wall mixer (2/3 hole) with provision for connection to shower rose for mixing hot and cold water screwed down for iron pipes suitable for 15mm bore pipe complete all as specified and directed. 65 Item No 64 : S & F in repair chromium plated Shower rose 15 mm size, 125mm long with 300 mm arms including fixing to pipe or union complete. 66 Item No 65 : S & F in repair brass/chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete. 67 Item No 66 : S & F in repair soap dish, any type, fixed to plugs with chromium plated brass screws complete. 68 Item No 67 : S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete. 69 Item No 68 : S&Fin repair PVC floor trap size 75/100mm dia out let with grating including connection to waste pipe with cement jointing including taking down existing trap complete all as specified and directed 70 Item No 69 : S & F in repair vitreous China Urinal, Half stall type, white incl providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing of flush pipe, grating and union for discharge pipe complete. 71 Item No 70 : S & F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) 72 Item No 71 : S & F Vitreuos china wash hand basin size 560x450mm oval shape counter type incl brackets or fixed to walls with anchor fasteners all cutting for and pinning in end of brackets or erecting stand, and inclusive of fixing and supply and waste pipeand CP waste coupling32 mm dia complete fixed. 73 Item No 72 : Supply & fix in repair brass chromium plated single lever mixerfor wash hand basin for mixing hot and cold water screwed down for iron pipes suitable for 15mm bore pipe complete. 74 Item No 73 : S & F PVC connections 15mm size with PTMT nuts of length 600mm complete. 75 Item No 74 : S & F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete. 76 Item No 75 : S&F in repair 15 mm dia bore bib taps, cast copper alloy chromium plated fancy type with crutch alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed. 77 Item No 76 : S & F in repair 15 mm dia bore fancy type chromium plated stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. 78 Item No 77 : Taking down and refixing of 15 mm dia Bib taps/Stop valves/Angle valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe. 79 Item No 78 : Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store measured overall as fixed along the centre line over fittings and accessories) complete. 80 Item No 79 : S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors and connecting with manholes or disposal place all as specified and as directed. 81 Item No 80 : S & F 110mm dia borePVC (SWR) bends with access door all as specified and as directed. 82 Item No 81 : S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls all as specified and as directed. 83 Item No 82 : S & F 110mm bore PVC (SWR) vent cowl with rubber ring joints,fixed to pipes all as specified and as directed. 84 Item No 83 : S & F of PVC (SWR) junction single, (Single T) 110 mm bore equal or unequal with acess door complete. 85 Item No 84 : M&L for PVC (SWR) pipessingle socketed, in any length with rubber ring joints, laid in trenches or in floors/walls of 75 mm bore of pipe etc complete all as specified and directed 86 Item No 85 : S&F PVC (SWR) bends ISI marked any radius of 75 mm borewithaccess door complete all as specified and directed. 87 Item No 86 : S & F of PVC (SWR) junction single, (Single T) 75 mm bore equal or unequal with acess door complete. 88 Item No 87 : Taking down copper /aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc.Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces ofwalls, floors etc complete all as specified and directed at site. 89 Item No 88 : Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch/Busbar including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed. 90 Item No 89 : Taking down carefully copper/aluminium Sub main wiring of any size fromsurface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. 91 Item No 90 : Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan bladesand deposit to MES store yard of AGE E/M complete all as specified and as directed. 92 Item No 91 : Taking down water heater ( geyser) any type after disconnecting all necessaryconnections and deposit to MES store yard of AGE E/M complete all as specified and as directed. 93 Item No 92 : M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts gradeISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches,including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly includingcutting, chasses and makinggooddisturbed surface to match with existing finish with plaster complete all as specified and directed for the following :- 94 (a) One light point controlled by one, one way switch 5 Amps 95 (b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator 96 (c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board. 97 (d)One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad. 98 Item No 93 : Description all as per item No 92 here in before butusing 2.5 sq mm single core copper conductor cable of multistranded FRLSH insulated unsheathed 1100 volts grade for 5/15 ampspointincluding necessary running of2.5 sq mm copper FRLSH wire as earth continuity conductor along with wiring and connecting to the common eath dolly. 99 Item No 94 : S & F modular switch piano flushtype, single pole, one way, and 5/6 Amp single module complete all as specified. 100 Item No 95 : S & F modular switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified. 101 Item No 96 : S & F modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified. 102 Item No 97 : S & F modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified. 103 Item No 98 : S & F for Ceiling rose, surface Bakelite with 3 terminals, ISImarked for batten fitting complete all as specified 104 Item No 99 : S&F lamp holder, PVC/ polycarbonate with back plate suitable for batten fittings all as specified and directed 105 Item No 100 : M & L forSub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable sizeincluding concealed in wall etcone run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit 106 Item No 101 : S & F for sheet metal enclosed busbar chamber of 200 A capacity 4 way in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. 107 Item No 102 : S & F for sheet metal enclosure MCBDBSPN12 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. 108 Item No 103 : S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, C curve complete all as specified and as directed. 109 Item No 104 : S & Ffor MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, C curve complete all as specified and as directed. 110 Item No 105 : S & Ffor metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Ampsincluding removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed 111 Item No 106 : S & F for energy efficient exhaust fan of 300 mm sweep made of metal body e complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan forconnection and making suitable size ofhole to existing brick wall for fan basecompelte all as specifiedand directed.(Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be includedin overall rate quoted). 112 Item No 107 : Re-fixing of exhaust fan of 300 mm sweep made of plastic/steel body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan forconnection and making suitable size ofhole to existing brick wall for fan basecompelte all as specifiedand directed. 113 Item No 108 : S & F LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 114 Item No 109 : Refixing electric water heater, storage type steel/ PVC body of capcity upto 50 litre complete with all accessories such as saftey valve, NRV, suitable connection pipe all as specified and directed 115 Item No 110 : Supply and fix electric water heater, storage type with heating element upto 2 KW capacity, BEE 5 star rated ISI marked complete with accessories such as saftey valve, NRV, suitable connection pipe all as specified and directed 116 Item No 111 : M & L for earthing complete with galvanized earth plate electrode 600mmx 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvenised earth lead wire of 4 mm dia by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 5 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work PCC(1:3:6) type C-1 pit with precast RCC Cover slab 40 mm thick in PCC(1:2:4) type B-1 reinforced with 6 mm dia MS bars @ 100 mm c/c both ways with funnel wire mesh and 20 mm dia GI pipe medium grade as watering pipe and connected to earthing point complete all as specified and as directed. 117 Item No 112 : Excavation in trenches not exceeding 1.5min width and not exceeding 1.5mdeep, in soft/loose soil for foundation, laying of pipes, wells, cesspits, manhole, pier holes & getting out complete all as specified and directed. 118 Item No 113 : M & L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in foundation filling, mass concrete etc complete all as specified. 119 Item No 114 : S & F of DWCPE (SN8) 180 (OD)/(ID) mm dia pipe and testing sewage line incl all items/fittings and activities to execute and make sewer line functional complete all as specified. 120 Item No 115 : M&L for cutting into existing manholes for connecting new drains, dia of pipe 180/200mm,making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished, and reforming benching as required complete all as specified and directed. 121 Item No 116 : M&L for Rendering 15mm thick in cement mortar 1:4 on fair facesof brick workor concrete surfaces, using waterproofing compound as per manufacturers instruction, finished even and smooth without using extra cementcomplete..Note:- (WPCshall be measured and paid separately) 122 Item No 117 : M&L for precastreinforced cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in manholes covers and similar articles, set in cement mortar 1:4 including necessary form workand similar articles complete all as specified and directed. 123 Item No 118 : M&L for mild steelTMT bars 10mmdia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 124 Item No 119 : M&L for Formwork to faces of walls,retaining walls, abutments,parapets and staircase railingsand similar work includingattached pillasters, buttresses,etc.; vertical or to batter complete all as spd. 125 Item No 120 : S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps all as specified and directed . Make : Supreme/ Finolex. 126 Item No 121 :M&L for providing concrete bed in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in bed to drain pipes, dia of 110mm, including packing under and haunching against the sides of the pipes completely after pipes are laid and tested complete all as specified and directed.Note: Width of concrete bed shall be outer diameter of drain pipe plus 30cm. 127 Item No 122 : S&F PVC SWR bends of 110 mm bore. 128 Item No 123 : S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia. 129 Item No 124 : Returning, filling in trenches including spreading, leveling,watering and well ramming in layers not exc 25cm thick complete all as specified and directed. 130 Item No 125 : Removing excavated material to distance not exc50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.
