|
| 1 | Dismantle all types of plain cement concrete works up to 150 mm thick stacking serviceable Materials at site andremoving rubbish as directed within a lead of 75 Metre in ground floor including roof. |
| 2 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars in ground floor including roof. |
| 3 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.In ground floor including roof. |
| 4 | Earth work in excavation of the foundation tranches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing spreading or stacking the spoils within a lead of 75Mtr as directed. The Item including necessary trimming the sides of tranches, levelling, dressing and ramming the bottom, bailing out water etc. as required complete. Depth of excavation not exceeding 1500 mm. |
| 5 | Earth work in filling in foundation trenches or plinth with good earth obtained from excavation of foundation in layers not exceeding 150mm including watering and ramming etc. layer by layer complete. (Payment to be Made on the basis of the Measurement of finish quality of work). |
| 6 | Supplying labours for taking out old Paver blocks carefully, stacking the same in proper stack and depositing the spoils as directed within a lead of 150 m. |
| 7 | Carefully lay old paver blocks in line and level to match with existing paver surface including Providing bedding layer of medium sand (50 to 80 mm average thick) over prepared concrete base and compacted by heavy duty vibrator plate compaction (joints filled with fine sand) as per specification including all lead, lifts, materials, labours etc. complete in all respect. |
| 8 | Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 9 | Provide and lay Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 10 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes.Pakur Variety |
| 11 | Ordinary Cement concrete (mix 1:1.5:3)with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.Pakur Variety |
| 12 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout propswith required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (a)Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work. |
| 13 | (b) 25 mm to 30 mm shuttering without staging in foundation |
| 14 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction, with Tor / Mild Steel. JSW / JSPL /SHYAM/SRMB/BMASL /ELECTROSTEEL / SSL. For works in foundation, basement and upto roof of ground floor/upto 4 m |
| 15 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge |
| 16 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary [Excluding cost of chipping over concrete surface]15 mm thick plaster(1:6)(a) In Ground Floor |
| 17 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 18 | Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth |
| 19 | Supplying, fitting and fixing in position G. I. pipes of TATA make for underground works with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbow, nipple, short piece etc. including cost of all materials, jointing materials, cutting pipes, making threads, cutting trenches up to 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made separately.)(i) 15 mm.dia. medium quality |
| 20 | (ii) 20mm.dia. medium quality |
| 21 | (iii) 25mm. dia. medium quality |
| 22 | (iv) 50mm.dia. medium quality |
| 23 | (v) 100 mm dia. medium quality |
| 24 | (vi) 150 mm dia. medium quality |
| 25 | Labour for dismantling G.I. pipe with fittings.(i) 15 mm. |
| 26 | (ii) 20 mm. |
| 27 | (iii) 25 mm. |
| 28 | (iv) 40 mm. |
| 29 | (v) 50 mm. |
| 30 | (vi) 100 mm. |
| 31 | Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).(i)15 mm |
| 32 | (ii)20 mm |
| 33 | (iii) 25mm. |
| 34 | (iv) 40mm. |
| 35 | (v) 50mm. |
| 36 | Supplying, fitting and fixing bib cock or stop cock. Supplying, fitting and fixing Chromium plated Bib Cock Short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 37 | Supplying, fitting and fixing Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO / ATLAS or equivalent)-15 mm dia. |
| 38 | Renewing high pressure polythene ballcock of approved quality with polythene ball and aluminium lever complete for pipe of dia.:(a) 25mm. dia. |
| 39 | Labour for hoisting plastic water storage tank -upto 1500 litre capacity.(a) Upto 1st story from G.L. |
| 40 | Labour for lowering plastic water storage tank and stacking in places as directed -upto 1500 litre capacity.(a) From 1st floor to G.L. |
| 41 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 42 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer1500 litre capacity |
| 43 | C.I. sluice valve with flanged ends drilled to as per I.S. 1358/62 and having all castiron components as per I.S. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 MT per sq. cm. Spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to I.S. 780/71, painted black all over with asphalt base paint tested to 21 Kg. (hydraulic pressure) per sq. cm. valve opening to anticlockwise3 direction, fitted and fixed complete. (i) 100 mm. |
| 44 | (ii) 150 mm. |
| 45 | Sluice valve chamber with C.I. heavy cover with locking arrangement, (weight not less than 25 kg) (size of chamber 450 mm X 600 mm inside upto 900 mm depth) 250 mm thick cement brick walls (6:1), 150 mm thick cement concrete (6:3:1) bedwith stonechips, 20 mm thick cement plaster(6:1) for inside wall and 15 mm thick cement plaster (4:1) for outerwalls including rounding corners. |
| 46 | Supplying fitting and fixing cast iron spun pipe conforming to I.S. 1536/1976 with all necessary specials including cutting tre4nches in any soil or through masonry, concrete etc. if necessary and mending good all damages including jointing pipes with Tyton joints as per manufacturer’s specifications and filling up the trenches all complete but excluding the cost of masonry or concrete work, if required. (a) Class A : (i)100 mm. nominal dia |
| 47 | (ii) 150mm nominal dia |
| 48 | Supplying, fitting and fixing brass ferrule including connection with G.I. pipes of TATAmake of following dia. and upto 450mm long with screw,jamnut,sockets etc.,complete in all respect, including cutting trenches in all sorts of soil and filling up the trenches as per directionof the Engineer - in - Charge.(i) 15 mm dia |
| 49 | (ii)20 mm |
| 50 | (iii) 25mm. |
| 51 | Supply of UPVC pipes & fittings conforming to IS-13592-1992(A) (i)Single Socketed 3 Meter Length 110 mm |
| 52 | (B) Fittings.(i) Plain Tee110mm. |
| 53 | (ii) Door Tee110mm. |
| 54 | (iii) Bend 450110mm. |
| 55 | (iv) Bend 87.50110mm. |
| 56 | (v) Vent Cowl.110mm. |
| 57 | (vi) Pipe Clip. 110mm. |
| 58 | (C ) Rubber Lubricant |
| 59 | (D) Solvent Cement |
| 60 | Removing chokage of water closet. |
| 61 | Removing chokage of urinal and waste trap. |
| 62 | Renewing brass spindle and valve of stop cock/bib cock/push cock/pillar cock.15 mm dia |
| 63 | Supplying & laying Double Wall Corrugated (with external annular corrugation and smooth internal walls) High Density Polyethelene Pipes conforming to IS 16098 (Part-II):2013 having Stiffness Class of SN 8 with Ring Stiffness not less than 8.00 KN/Sqm. and Impact Resistance TIR value not more than 10% including necessary jointing materials for nonpressureunderground Drainage, Sewerage & Cross drainage application.(i) 150mm internal dia. |
| 64 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz.socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket,reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respectincluding cost of all necessary fittings as required,jointing materials andtwo coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories,specials. Payment for painting will be made seperately)(i) 15 mm |
| 65 | (ii) 20 mm |
| 66 | (iii) 25 mm |
| 67 | (iii) 40 mm |
| 68 | (iv) 50 mm |
| 69 | Supplying, fitting and fixing push cock of heavy quality and of approved make and brand.PTMT Push Cock (20 mm F/T) with spout ( Prayag or equivalent) |
