|
| 1 | Repair / Routine maintenance, including carrying out daily check of fire alarm / fire fighting system complete with electronic control panel in the following buildings, including providing personnel to attend the fire alarm system faults, testing, checking and replacement of unserviceable minor components i.e. nuts, bolts, washers etc., other than those mentioned in Schedule here-inafter, and fire alarm system consisting of the following:(a) Indicator(b) Electronic hooter(c) Manual call point(d) Smoke detector(e) Heat detector(f) Electronic fire control panel(g) Main / Zone cards(h) Battery of fire panel DC supply(j) All wiring and cable connections(k) Control / Monitor moduleNotes :(A) Contractor shall provide adequate manpower — at least four (4) skilled personnel — for testing of the fire-fighting system of buildings as per schedule issued by the user section. The cost of testing shall be deemed to be included in the item rate.(B) Minor items such as fuses, loop cards, detector circuits, etc., required at site to make the system functional, are included in the item rate.(C)Contractor’s technician and helper shall report daily to JE (E/M) regarding maintenance work at site.(D)Rate is also inclusive of checking battery level of diesel engine pump and ensuring it is charged, if not |
| 2 | Details of Buildings (to be considered while quoting)(i) Kanya, Swati, Meena – G + 13 floors(ii) Chitra, Anuradha, Alaknanda – G + 14 floors(iii) Archana – G + 15 floors(iv) Bharani, Saravana, Vidya, Vijaya – G + 12 floors (13 storeys)(v) Revati, Rohini, Karthikeya, Gemini – G + 9 floors (10 storeys)(vi) Narmada, Tapti, Kaveri, Hoogly, Vishkarma – G + 6 floors (7 storeys)(vii) WNC (O) Mess Main Building, Annex Building, Transit & Himadri Buildings – G + 7 floors (8 storeys)(viii) Chenab, Jhelam – G + 20 floors |
| 3 | Details of Buildings (to be considered while quoting) (i) Dhanush, Brishabh, Tula, Makar, Mesh, “G” Block, “H” Block, Kumbh – G + 14 floors(ii)Jyesta & Dhanista – G + 16 floors, P-37 Building(iii)G Block, F1 Block, AQ Block, AR Block and 200 Sailors Accn – G + 6 floors(iv)Asha-2 ,Asha-3,Asha-4, Asha-5 – G + 5 floors(v)R-41 & R-42 Buildings – G + 21 floors(vi)SHO Building – G + 2 floors(vii)NKG School(viii)F2 to F6 Buildings – G + 5 floors) |
| 4 | Supply and fix in repair detectors complying with and type-certified to EN-45, addressable type multisensor detector with heat and smoke combination (photoelectric/optical) with base, having self-built intelligence, conforming to IS: 11360, complete all as specified and directed.Make: Bosch / Morley / Apollo / GST / Agni / RavelNote: Loop cards, circuits, etc., as required to make the system functional, shall be deemed to be included in the quoted rate and no extra payment shall be made to the contractor. |
| 5 | Supply & fix in repair Maintenancefreebattery duly charged12 V 7.2 AH, ISI marked complete all as specified and directed Make :- EXIDE / TATA / Green / Amaron |
| 6 | Supply, replacement, installation, testing and commissioning of addressable type manual call point, complete all as specified and directed.Make: Schneider / Honeywell / Bosch / Siemens |
| 7 | Supply, replacement, installation, testing and commissioning of microprocessor-based addressable fire alarm/detection control panel, having 2-wire fault-tolerant loop, networkable, with 2 loops, each loop capable of accessing up to 99 detectors and 99 modules, complete with all accessories.Note:(1)The panel shall be capable of indicating the location of all fire/fault conditions of addressable units via their address, and shall include rectifier, loop cards, and LCD display unit for indication of Fire/Fault signals with address.(2)The panel shall have built-in power supply and battery charger with maintenance-free batteries 7.2 Ah, 2 × 12V SMF type, providing minimum 48-hour standby operation, complete as required and complying with EN 54.(3)The work shall include provision of a 15A power point connection from meter room to fire control panel, all as specified and directed by the Engineer-in-Charge. |
| 8 | Supply and fix in repair canvas fire hose, 63 mm bore, 15 m long, conforming to IS: 636–1988, having male and female brass couplings at both ends, complete all as specified and directed.Make: Minimax / Safex / Dunlop |
| 9 | Supply and fix in repair stainless-steel nozzle, conforming to IS 903 : 1993, size 63 mm × 15 mm bore, suitable for 63 mm dia canvas hose pipe, complete all as specified and directed by the Engineer-in-Charge.Make: Minimax / Safex / Dunlop |
| 10 | Supply and fix in repair hose reel drum complete with 30 metres × 20 mm dia rubber hose pipe, plain 2-ply rayon braided, high pressure type, conforming to IS: 12585, complete all as specified and directed by the Engineer-in-Charge.Make: Minimax / Safex / Dunlop |
| 11 | Supply and fixing in repair MS ERW pipe, 100 mm dia, heavy grade, ISI marked, conforming to IS: 1239, for suction and delivery line of pump and rising main, including all necessary fittings, welding, painting with one coat of red oxide primer and two coats of synthetic enamel paint, and providing PCC supports, all as specified and directed by the Engineer-in-Charge.Make: Jindal / Tata / Zenith / BST / SAIL |
| 12 | Supply and fix in repair gun metal two-way fire brigade inlet, ISI marked, complete with adaptor 80 mm dia × 63 mm dia, including all accessories and testing, complete all as specified and directed by the Engineer-in-Charge.Make: Minimax / Safex / Dunlop |
| 13 | Supply and fix in replacement, installation, testing and commissioning of addressable electronic sounder-cum-strobe, complete all as specified and directed by the Engineer-in-Charge.Make: Schneider / Honeywell / Bosch / Siemens |
| 14 | M & L for repairing of existing unserviceable electronic sounder-cum-strobe, manual call point, and smoke detectors, including repair/replacement of loop cards, complete with opening, soldering of circuits, cleaning, replacement of glass, testing, and painting, all as specified and directed by the Engineer-in-Charge. |
| 15 | Supply and fixing in repair PVC insulated, PVC sheathed, armoured copper conductor cable, size 4-core × 1.5 sqmm, including fixing on walls with saddles and making connections, complete all as specified and directed by the Engineer-in-Charge. |
| 16 | Supply and fixing in repair PVC insulated, PVC sheathed, armoured copper conductor cable, size 2-core × 1.5 sqmm, including fixing on walls with saddles and making connections, complete all as specified and directed by the Engineer-in-Charge. |
| 17 | Material and labour for factory-fabricated hose box made of 18-gauge MS sheet, size 800 mm × 600 mm × 250 mm, with double door having 4 mm thick glass panels and door frame made of 16-gauge MS sheet, painted fire red on the outside and brilliant white on the inside, fixed on wall with necessary nuts, bolts, or by welding to existing MS pipe using supporting angle, complete all as specified and directed by the Engineer-in-Charge. |
| 18 | Material and labour for carrying out servicing of diesel engine pump set of capacity 75/60 HP, including repair and replacement of worn-out or defective spare parts, and preventive maintenance of radiator and all connected assemblies, complete all as specified and directed by the Engineer-in-Charge.The scope of work shall include replacement of the following:(a) Oil filter(b) Fuel filter(c) Air filter(d) Coolant(e) Engine oil (as per the capacity of engine)Servicing shall include checking, cleaning, tightening, lubrication, replacement of consumables, and testing of engine operation after completion of work. |
| 19 | Supply and fix in repair branch pipe, gun metal, 63 mm, ISI marked, with instantaneous inlet, threaded outlet, and 15 mm bore nozzle, complete all as specified and directed by the Engineer-in-Charge. |
| 20 | Supply and fix in repair double-headed outlet hydrant valve (ISI marked) , 100 mm size, having 63 mm outlets with lock pin wheel, ISI marked, complete all as specified and directed by the Engineer-in-Charge. |
| 21 | Supply and fix in repair single-headed outlet hydrant valve (ISI marked) , 100 mm size, ISI marked, having 63 mm outlet with lock pin wheel, complete all as specified and directed by the Engineer-in-Charge. |
| 22 | Supply and fix in repair sluice valve (ISI marked) , 150 mm size, both ends flanged, with high tensile stainless steel spindle, cast iron body conforming to IS: 14846, ISI marked, PN-1.6, including all joints with rubber or fibre board, nuts, bolts, and washers, complete all as specified and directed by the Engineer-in-Charge. |
| 23 | Supply and fix in repair sluice valve (ISI marked) , 100 mm size, both ends flanged, with high tensile stainless steel spindle, cast iron body conforming to IS: 14846, ISI marked, PN-1.6, including all joints with rubber or fibre board, nuts, bolts, and washers, complete all as specified and directed by the Engineer-in-Charge. |
| 24 | Supply and fix in repair non-return valve (NRV) (ISI marked) , 150 mm size, ISI marked, both ends flanged, with high tensile stainless steel spindle, cast iron body, including all joints with rubber or fibre board, nuts, bolts, and washers, complete all as specified and directed by the Engineer-in-Charge. |
| 25 | Supply and fix in repair non-return valve (NRV) (ISI marked) , 100 mm size, ISI marked, both ends flanged, with high tensile stainless steel spindle, cast iron body, including all joints with rubber or fibre board, nuts, bolts, and washers, complete all as specified and directed by the Engineer-in-Charge. |
| 26 | Supply and fix in repair foot valve (ISI marked), 150 mm dia, ball type (Model B-5), pressure rating 10/15 Kg/cm², ISI-marked, fixed in position at the specified location, including M & L for making flanged joints, repair of connected portions, and making good existing PCC surface, complete all as specified and directed by the Engineer-in-Charge. |
| 27 | Supply and fix in repair foot valve (ISI marked), 100 mm dia, ball type (Model B-5), pressure rating 10/15 Kg/cm², ISI-marked, fixed in position at the specified location, including M & L for making flanged joints, repair of connected portions, and making good existing PCC surface, complete all as specified and directed by the Engineer-in-Charge. |
| 28 | M & L for disconnecting motor from pump of any make and model, removing bearings using suitable bearing puller gear, and fixing new bearings at DE / NDE ends, including necessary cleaning, greasing, alignment and testing to ensure smooth operation without vibration, for the following motor capacities: |
| 29 | (a) Pump coupled with 75 HP motor — Bearing size 6215 ZZ & 6216 ZZ Make of Bearings: SFC / NBC / SKF |
| 30 | (b) Pump coupled with 60 HP motor — Bearing size 6312 ZZ & 6311 ZZMake of Bearings: SFC / NBC / SKF |
| 31 | (c) Pump coupled with up to 15 HP motor — Bearing size 6307 ZZ & 6309 ZZMake of Bearings: SFC / NBC / SKF |
| 32 | Supply and fix self-lubricated, asbestos-free, non-metallic and non-graphite gland packing of sizes 8 mm to 12 mm, complete all as specified and directed by the Engineer-in-Charge.Make: Champion / Techno or other approved commercial equivalent |
| 33 | Material & Labour for scraping of paint on complete pump, motor, base frame and accessories, including removal of old paint, cleaning, and preparation of surfaces, followed by application of one coat of red oxide primer and two coats of synthetic enamel paint of approved shade, for motors of capacity 15 HP to 75 HP, complete all as specified and directed by the Engineer-in-Charge. |
| 34 | Supply and fix compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and similar structures, including caps, bases, splices, etc., built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, and gusset plates, of steel grade Fe 410-W (Gde E-250), quality B, complete all as specified and directed by the Engineer-in-Charge. |
| 35 | Supply and fix in repair heavy-duty rubber vibration pads for pump base frames, as per approved sample, suitable for the following sizes of pump sets: |
| 36 | (a)50 to 75 HP |
| 37 | (b) 05 to 15 HP |
| 38 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), including removal of debris outside MD land, complete all as specified and directed by the Engineer-in-Charge. |
| 39 | Material and labour for cement concrete (1:2:4), type B-2 (using 40 mm graded stone aggregate) as in support of base frame, with MS bolts placed in concrete, and hardstanding finished even and fair without using extra cement, complete all as specified and directed by the Engineer-in-Charge.Note: Location and size of bolts shall match the existing arrangement. |
| 40 | Supply and laying in replacement of copper PVC insulated, unarmoured power cable, 1100 volts grade, conforming to IS 7098 (Part I) – 1988, of sizes given below, including fixing on walls with saddles and providing HDPE pipe of suitable size for mechanical protection where required, complete all as specified and directed by the Engineer-in-Charge. |
| 41 | (a)35 Sq mm Single core |
| 42 | (b)25 Sqmm Single core |
| 43 | (c)16 Sqmm Single core |
| 44 | Material and labour for disconnecting motor power cables of various sizes from electrical motors of different capacities and decoupling from the pump sets; removing and taking down carefully and transporting to authorised workshop; dismantling stator and rotor; rewinding stator assembly with super-enamelled copper winding wire of suitable gauge matching existing size; cleaning of slots and core using carbon tetrachloride solution; applying two coats of insulation varnish; keeping stator assembly in a heating chamber to improve insulation strength; reassembling the motor completely; transporting back to site; coupling pump to motor and checking for proper shaft alignment to ensure vibration-free operation; connecting power cables to motor and testing complete for the following capacities: |
| 45 | 60/75 HP |
| 46 | up to 15 HP |
| 47 | Supply and fix in repair battery 12V, 180 AH, suitable for diesel engine pump, complete all as specified and directed by the Engineer-in-Charge. |
| 48 | Supply and fix in repair DOL / Star-Delta starter, suitable for 5 HP to 10 HP pump set, with current relay range 7.5–16 Amp, 3-phase, 430 Volts, 50 Hz, complete all as specified and directed by the Engineer-in-Charge. |
| 49 | Material & Labour for Construction of brick masonry valve chamber in repair, size 1.2 × 1.2 × 1.2 m (internal dimensions), with foundation in PCC (1:4:8) type D-2 over 15 cm thick hardcore of broken stone, 23 cm thick brick walls built in cement mortar (1:4), internal and external plaster 15 mm thick in CM (1:3), top finished even and smooth, 10 mm thick MS plate cover on 50×50×6 mm angle frame embedded in PCC (1:2:4) type B-1 coping, hinged and lockable with holdfasts, including one coat of red oxide primer and two coats of synthetic enamel paint on steel surfaces, and earthwork in any type of soil including disposal of debris outside MD land, complete all as specified and directed by the Engineer-in-Charge. |
| 50 | Rubbing with emery paper for removing rust and loose paint on firefighting pipelines, fittings, motors, pumps, cabinet boxes, valve chamber covers, hydrant posts, fire brigade inlets and related components, including cleaning and applying one coat of red oxide primer and two coats of red synthetic enamel paint, for buildings up to G+15 floors, complete all as specified and directed by the Engineer-in-Charge. |
| 51 | Supply and laying (in replacement) of spigot and socket ductile iron water tubing, class K-9, 150 mm bore, with cement mortar lining on the inner surface and one coat of bituminous paint over the exposed surface, ISI marked, conforming to IS 8329:2000, including rubber joint of suitable size, laid on roof, floor, or trenches with proper alignment, tested against leakage before backfilling, complete all as specified and directed by the Engineer-in-Charge. |
| 52 | Material and labour for cast iron / ductile iron specials conforming to IS 1538 / IS 3523, spigot / socket or flanged fittings such as bends, tees, collars, flanged sockets, spigots, tapers and tail pieces, suitable for 100 / 150 / 200 / 250 / 300 mm bore pipes, complete all as specified and directed by the Engineer-in-Charge.(Note: Joints and jointing materials shall be measured and paid separately.) |
| 53 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth, and getting out in soft / loose soil, complete all as specified and directed by the Engineer-in-Charge. |
| 54 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil, complete all as specified and directed by the Engineer-in-Charge. |
| 55 | Removing excavated material, exceeding 250 m but not exceeding 500 m, and depositing where directed, complete all as specified and directed by the Engineer-in-Charge. |
| 56 | Material and labour in repairs for run lead joint, size 150 mm bore, in existing pipeline, using pig lead, including pumping out / bailing out water, necessary excavation and earthwork in any type of soil, to repair the joints and restore functionality, complete all as specified and directed by the Engineer-in-Charge. |
| 57 | Supply and fix in repair hydrant valve wheel, complete all as specified and directed by the Engineer-in-Charge. |
| 58 | Supply and fix in repair hydrant stainless steel female coupling, 63 mm dia, complete all as specified and directed by the Engineer-in-Charge. |
| 59 | Supply and fix in repair / replacement of gun-metal gate valve (ISI marked) in existing line, with iron wheel head Class I, made of brass, screwed both ends for GI pipe with union, ISI marked, complete all as specified and directed by the Engineer-in-Charge, of the following sizes: |
| 60 | 25 mm bore |
| 61 | 40 mm bore |
| 62 | 50 mm bore |
| 63 | Supply and fix in repair MS ERW pipe, 150 mm dia, heavy grade, ISI marked, conforming to IS:1239, for suction and delivery of pump and rising main, including all necessary fittings, welding, painting with one coat of red oxide primer and two coats of synthetic enamel paint, and providing PCC supports, complete all as specified and directed by the Engineer-in-Charge. |
| 64 | Supply and fix in repair MS ERW pipe, 80 mm dia, heavy grade, ISI marked, conforming to IS:1239, for suction and delivery of pump and rising main, including all necessary fittings, welding, painting with one coat of red oxide primer and two coats of synthetic enamel paint, and providing PCC supports, complete all as specified and directed by the Engineer-in-Charge. |
| 65 | Material & Labour for Earthing complete with galvanised steel earth plate electrode, size 600 × 600 × 6 mm, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, surrounded on all sides by 15 cm thick packed layers of charcoal dust and common salt in alternate layers, connected using galvanised iron strip 25 × 4 mm as earthing lead, secured by bolts, nuts, check nuts and washers of galvanised iron or steel, protected by GI pipe light grade 40 mm dia up to 7.5 m long connected to the main control board,Also including GI pipe light grade 40 mm bore for watering, with funnel and wire mesh, RCC pit cover 50 mm thick, and PCC chamber pit in PCC (1:2:4) type C-2, including excavation, backfilling and disposal of surplus soil not exceeding 50 m distance, and making a suitable test point connection as per Plate No. 3, with testing on completion, complete all as specified and directed by the Engineer-in-Charge. |
| 66 | Supply and fix in repair 32 Amp, 415 Volt, 50 Hz, AC MCB, triple pole and earth enclosure, complete with a three-pin and earth plug with socket, including all necessary connections, complete all as specified and directed by the Engineer-in-Charge. |
| 67 | Material and labour for cleaning of existing valve chamber, including removal of unwanted materials such as plastics, soil, debris, mud, etc., and depositing where directed, complete all as specified and directed by the Engineer-in-Charge. |
| 68 | Supply and fix in repair pressure gauge, 150 mm dia, range 0–10 Kg/cm², oil-filled type, as per approved sample, complete all as specified and directed by the Engineer-in-Charge.Note: The quoted rate shall include provision of adaptor / ferrule / check nut and any necessary alteration to MS or CI pipe for tapping, if required. |
| 69 | Supply and fix in repair 150 mm bore hand-operated butterfly valve, capable of withstanding pressure not less than 15 Kg/cm², complete with all accessories and fittings, all as specified and directed by the Engineer-in-Charge. |
| 70 | Supply and fix in repair 100 mm bore hand-operated butterfly valve, capable of withstanding pressure not less than 15 Kg/cm², complete with all accessories and fittings, all as specified and directed by the Engineer-in-Charge. |
| 71 | Taking out existing unserviceable lid cover of PVC water storage tank and supplying and fixing FRP lid cover on existing PVC tank, including complete closing and locking arrangement accessories as per BMC specification, complete all as specified and directed by the Engineer-in-Charge of the following :- |
| 72 | 5000 Ltrs PVC tank |
| 73 | 3000 LtrsPVC tank |
| 74 | Attending water supply breakdowns of 150 / 100 mm dia CI / DI / MS / GI pipeline at any position, location, or depth, including excavation, earthwork, cutting of pipes, welding, replacement of damaged pipes or fittings (flanges, bends, collars, nuts, bolts, gaskets, run lead joints, etc.), and testing and making good disturbed surfaces after rectification, complete all as specified and directed by the Engineer-in-Charge.Notes:(a) Items such as run lead joint, CI/DI/MS fittings or pipes, and nuts/bolts shall be measured and paid separately under relevant Schedule ‘A’ items.(b) Items such as welding, gasket, etc. are deemed to be included in the quoted rate.(c) Contractor shall complete breakdowns within 24 hours of complaint; otherwise, a panel recovery of ₹2500 per breakdown shall be imposed. |
| 75 | Material and labour for cutting existing DI pipes (150 mm or 100 mm bore or any size) and reducing for insertion of DI fittings to the required length in any position or location, complete all as specified and directed. |
| 76 | Supply and fix in repair hose drum adaptor connection (shank reducer), 63 mm dia, complete all as specified and directed by the Engineer-in-Charge. |
| 77 | Supply and fix in repair stainless steel lock pin for 63 mm dia coupling, complete all as specified and directed by the Engineer-in-Charge. |
| 78 | Supply and fix in repair PVC female blank cap of hydrant (with chain), complete all as specified and directed by the Engineer-in-Charge. |
| 79 | Supply and fix in repair PVC water storage tank, 5000 Ltr capacity, minimum 3-layer, ISI marked, including hoisting and fixing in position, disconnecting existing tank connections, providing new tank fittings and reconnection up to 50 mm dia GI pipe, replacing tank nipples and GI fittings as required, complete all as specified and directed by the Engineer-in-Charge. |
| 80 | Supply and fix in repair automatic battery charger, 12V, 10 Amps, suitable for 180 AH diesel engine pump, complete all as specified and directed by the Engineer-in-Charge. |
| 81 | Supply and fix in repair 20 mm dia stainless steel shutoff nozzle, conforming to IS:903, complete all as specified and directed. |
| 82 | Supply and fix in repair non-return valve (ISI marked) or washer for fire brigade inlet and hydrants, complete all as specified and directed by the Engineer-in-Charge. |
| 83 | Supply and fix in repair soft starter, 3-phase, 415 Volt, with comprehensive motor protection, programmable overload protection, built-in RTD and thermistor input, constant current adaptive acceleration and deceleration for smooth starting and stopping of motor, complete all as specified and directed for the following capacities: |
| 84 | 75 HP |
| 85 | 60 HP |
| 86 | Supply and fix in repair brass float valve (ISI marked), high-pressure type with polyethylene flat float and fly nut, complete, screwed for GI pipe 40 mm bore, including necessary GI fittings such as elbow, reducer, nipple, etc., complete all as specified and directed. |
| 87 | Supply and fix in repair approved quartz bulb sprinkler, 15 mm dia, pendent type, conforming to IS:15106, chrome plated with rosette plate, with temperature rating 68°C, complete with universal deflector, as approved by T.A.C., complete all as specified and directed.Make: Tyco / Viking / Spraysafe |
