Bids Are Invited For Repair, Maintenance, And Installation Of Plant/ Systems/Equipments (Version 2) - Rsp; Ac Motors; As Per Scope Of Work; 10 4004210216 INSTALN/RELOCN-SPLIT/TOWER AC- 1.5-5TR Scope of Work : INSTALLATION / RELOCATION OF SPLIT / TOWER AC UNIT, CAPACITY: 1.5-5TR JOB INCLUDES: 1. ISOLATION AND DISCONNECTION OF ELECTRICAL CABLES AND ASSOCIATED PIPES. 2. COMPLETE DISMANTLING OF AC UNIT AND SHIFTING DISMANTLED COMPONENTS TO NEW LOCATION. 3. SUPPLY AND INSTALLATION OF 15 MTR COPPER PIPES 4. FABRICATION AND FIXING OF SUITABLE FRAME FOR FIXING THE INDOOR AND OUTDOOR UNITS. 5, SUPPLY, LAYING AND CONNECTION OF ELECTRICAL CABLE 4 X 4 SQMM, 25 MTRS LENGTH. 6. SUPPLY AND FIXING OF MCB/ STARTER. 7. LEAK TESTING OF CONNECTED REFRIGERANT & LINES AND RECTIFICATION. 8. SUPPLY AND FIXING OF SUITABLE PIPE OF 15 MTR LENGTH BETWEEN DRAIN PIPE AND NEAREST DRAIN PIT. 9. FILLING OF GAS IF REQUIRED, ALL CONNECTION AND TESTING OF AC UNIT. 10. ANY JOB NOT SPECIFICALLY MENTIONED BUT REQUIRED FOR COMPLETE THE RELOCATION OF SPLIT AC UNIT IS AT PARTYS SCOPE. Ea 24 20 4004332439 RPR/ O/H OF SPRAYING SYS-VENTILTN CHMBER SCOPE OF WORKREPAIR / OVERHAULING OF SPRAYING SYSTEM IN VENTILATION CHAMBERS. 1. REMOVAL OF CHOKAGES FROM SPRAY PIPES (1/2 INCH CONNECTING THREADED G.I PIPES TO MAIN HEADER) / NOZZLES IN AIR WASHERS AFTER DISMANTLING THEM & FIXING BACK TO THE HEADER. 2. REPAIR OF SPRAY PIPES & THREADING FOR FIXING TO HEADER & NOZZLES. SPRAY NOZZLES THREADED TO SPRAY PIPE & THREADED UNION AT ONE END FOR CONNECTION TO THE HEADERS. 3. REPLACEMENT OF DEFECTIVE BRASS NOZZLES WITH THE NEW ONE. 4. TESTING OF WATER SPRAY SYSTEM. N.B: BRASS NOZZLE REQUIRED WILL BE SUPPLIED BY INDENTOR.THERE ARE 11 TO 13 SPRAY NOZZLES THREADED TO EACH SPRAY PIPE & NOS OF SPRAY PIPES IN COOLING CHAMBER OF EACH VENTILATION SYSTEM IS FROM 15 TO 20.JOBS TO BE CARRIED OUT ON EACH VENTILATION CHAMBER BASIS. ALL OTHER CONSUMABLES & TOOLS TACKELS REQUIRED TO COMPLETE THE JOB REQUIRED ARE TO BE ARRANGED Ea 12 30 4004400068 RPR- RECIRCULATION WTR PUMP-VENT.SYSM SCOPEREPAIR OF RE-CIRCULATION WATER PUMPS (7.5 HP TO 20 HP) OF VENTILATION SYSTEM IN SMS-II. THE JOB CONSISTS OF THE FOLLOWING. (I)REMOVAL FORM BASE & DISMANTLING OF PUMP. (II)REMOVAL OF PUMP IMPELLER FROM CASING, REPAIR, RECTIFICATION & OVERHAULING OF PUMPS. (III)CHECKING OF BOTH SIDE BEARING & REPLACEMENT IF REQUIRED. (IV)DAMAGED KEY WAY TO BE IDENTIFIED & REPAIRED. (V)CHECKING & RECTIFICATION OF MOTOR & PUMP SHAFT KEY WAY,COUPLING SHAFT HOLES KEY-WAYS & NECESSARY REPAIR . (VI) REPLACEMENT OF DAMAGED KEYS WITH NEW ONE AS REQUIRED. (VII)REAPAIR/ REPLACEMENT OF DAMAGED/WORN OUT IMPELER SHAFT BY NECESSARY MACHINING. (VIII)ASSEMBLY OF PUMP IMPELLER WITH NECESSARY PACKING, GLAND PACKING AND ALIGNMENT FOR FREE MOVEMENT. (IX)FIXING OF COUPLING & CONNECTION WITH DRIVE (EACH COUPLING IS HAVING 4 NOS HOLES). (X)TESTING OF PUMP FOR REQUIRED PRESSUE & LEAKAGES. N.B:-NECESSARY RUBBER BUSHES, WASHERS, NUT & BOLTS REQUIRED FOR THE COUPLING TO BE SUPPLIED BY THE PARTY. Ea 36 40 4002031018 DISMANTLING OF MOTORS,5-10KW,LIFT<20M & SCOPEDISMANTLING OF HORIZONTAL / VERTICAL MOUNTED PUMP MOTORS (ELECTRICAL MOTORS) OF RATING: 5 KW TO 10 KW INSTALLED AT DIFFERENT UNITS/ AREAS/LOCATIONS OF TE (WS). THE SCOPE INCLUDES DECOUPLING, DISMANTLING OF COUPLING GUARD,/COUPLING, REMOVAL OF FOUNDATION BOLTS, SHIFTING THE MOTORS AND PLACING THE SAME ON THE PUMP HOUSE FLOOR OR AT A SUITABLE PLACE READY TO TRANSPORT POSITION AS PER DIRECTION OF THE EXECUTING OFFICER /ENGINEER IN CHARGE / REPRESENTATIVE OF HOS, TE(WS). LIFT UP TO 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES, LIFTING DEVICE REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY / AGENCY. Ea 50 50 4002031019 DISMANTLING OF MOTORS,>10-25KW,LIFT<20M DISMANTLING OF HORIZONTAL / VERTICAL MOUNTED PUMP MOTORS (ELECTRICAL MOTORS) OF RATING: ABOVE 10 KW TO 25 KW INSTALLED AT DIFFERENT UNITS/ AREAS/LOCATIONS OF TE (WS). THE SCOPE INCLUDES DECOUPLING, DISMANTLING OF COUPLING GUARD,/COUPLING, REMOVAL OF FOUNDATION BOLTS, SHIFTING THE MOTORS AND PLACING THE SAME ON THE PUMP HOUSE FLOOR OR AT A SUITABLE PLACE READY TO TRANSPORT POSITION AS PER DIRECTION OF THE EXECUTING OFFICER /ENGINEER IN CHARGE / REPRESENTATIVE OF HOS, TE(WS). LIFT UP TO 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES, LIFTING DEVICE REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY / AGENCY. Ea 50 60 4002031020 DISMANTLING OF MOTORS,>25-50KW,LIFT<20M DISMANTLING OF HORIZONTAL / VERTICAL MOUNTED PUMP MOTORS (ELECTRICAL MOTORS) OF RATING: ABOVE 25 KW TO 50 KW INSTALLED AT DIFFERENT UNITS/ AREAS/LOCATIONS OF TE (WS). THE SCOPE INCLUDES DECOUPLING, DISMANTLING OF COUPLING GUARD,/COUPLING, REMOVAL OF FOUNDATION BOLTS, SHIFTING THE MOTORS AND PLACING THE SAME ON THE PUMP HOUSE FLOOR OR AT A SUITABLE PLACE READY TO TRANSPORT POSITION AS PER DIRECTION OF THE EXECUTING OFFICER /ENGINEER IN CHARGE / REPRESENTATIVE OF HOS, TE(WS). LIFT UP TO 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES, LIFTING DEVICE REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY / AGENCY. Ea 30 70 4002031021 DISMANTLING OF MOTORS,>50-150KW,LIFT<20M DISMANTLING OF HORIZONTAL / VERTICAL MOUNTED PUMP MOTORS (ELECTRICAL MOTORS) OF RATING: ABOVE 50 KW TO 150 KW INSTALLED AT DIFFERENT UNITS/ AREAS/LOCATIONS OF TE (WS). THE SCOPES INCLUDES DECOUPLING, DISMANTLING OF COUPLING GUARD,/COUPLING, REMOVAL OF FOUNDATION BOLTS, SHIFTING THE MOTORS AND PLACING THE SAME ON THE PUMP HOUSE FLOOR OR AT A SUITABLE PLACE READY TO TRANSPORT POSITION AS PER DIRECTION OF THE EXECUTING OFFICER /ENGINEER IN CHARGE / REPRESENTATIVE OF HOS, TE(WS) . LIFT UP TO 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES, LIFTING DEVICE REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY Ea 20 80 4002031022 DISMANTLING OF MOTOR,>150-400KW,LIFT<20M DISMANTLING OF HORIZONTAL / VERTICAL MOUNTED PUMP MOTORS (ELECTRICAL MOTORS) OF RATING: ABOVE 150 KW TO 400 KW INSTALLED AT DIFFERENT UNITS/ AREAS/ LOCATIONS OF TE (WS). THE SCOPES INCLUDES DECOUPLING, DISMANTLING OF COUPLING GUARD,/ COUPLING, REMOVAL OF FOUNDATION BOLTS, SHIFTING THE MOTORS AND PLACING THE SAME ON THE PUMP HOUSE FLOOR OR AT A SUITABLE PLACE READY TO TRANSPORT POSITION AS PER DIRECTION OF THE EXECUTING OFFICER /ENGINEER IN CHARGE / REPRESENTATIVE OF HOS, TE(WS). LIFT UP TO 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES, LIFTING DEVICE REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY / AGENCY. Ea 20 90 4002051683 INSTALLATION MOTOR,>10-25KW,LIFT<20M & L INSTALLATION /ERECTING OF HORIZONTAL/VERTICAL PUMP/ COMPRESSOR/ BLOWER, MOTOR OF RATING OF ABOVE 10KW TO 25 KW AT DIFFERENT UNITS/LOCATIONS/AREAS OF TE-WS. THE MOTOR SHALL BE CHANGED FROM HORIZONTAL POSITION TO VERTICAL POSITION OR VICE VERSA AT SITE AS PER REQUIREMENT. THE SCOPE SHALL INCLUDE FITTING OF COUPLING IN THE MOTOR SHAFT, PLACEMENT OF MOTOR IN POSITION / BASE FRAME, FIXING OF FOUNDATION BOLT, ALIGNMENT AND COUPLING. ALIGNMENT SHALL BE CHECKED/ CERTIFIED BY ENGINEERING IN-CHARGE OR REPRESENTATIVE OF DGMTE-WS(HOS).LIFT OF 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY. Ea 50 100 4002051684 INSTALLATION MOTOR,>25-50KW,LIFT<20M & L INSTALLATION /ERECTING OF HORIZONTAL/VERTICAL PUMP/ COMPRESSOR/ BLOWER, MOTOR OF RATING OF ABOVE 25KW TO 50 KW AT DIFFERENT UNITS/LOCATIONS/ AREAS OF TE-WS. THE MOTOR SHALL BE CHANGED FROM HORIZONTAL POSITION TO VERTICAL POSITION OR VICE VERSA AT SITE AS PER REQUIREMENT. THE SCOPE SHALL INCLUDE FITTING OF COUPLING IN THE MOTOR SHAFT, PLACEMENT OF MOTOR IN POSITION / BASE FRAME, FIXING OF FOUNDATION BOLT, ALIGNMENT AND COUPLING. ALIGNMENT SHALL BE CHECKED/ CERTIFIED BY ENGINEERING INCHARGE OR REPRESENTATIVE OF DGMTE-WS (HOS).LIFT OF 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY. Ea 30 110 4002051685 INSTALLATION MOTOR,>50-150KW,LIFT<20M & INSTALLATION /ERECTING OF HORIZONTAL/VERTICAL PUMP/ COMPRESSOR/ Ea 20 BLOWER, MOTOR OF RATING OF ABOVE 50KW TO 150 KW AT DIFFERENT UNITS/LOCATIONS/AREAS OF TE-WS. THE MOTOR SHALL BE CHANGED FROM HORIZONTAL POSITION TO VERTICAL POSITION OR VICE VERSA AT SITE AS PER REQUIREMENT. THE SCOPE SHALL INCLUDE FITTING OF COUPLING IN THE MOTOR SHAFT, PLACEMENT OF MOTOR IN POSITION / BASE FRAME, FIXING OF FOUNDATION BOLT, ALIGNMENT AND COUPLING. ALIGNMENT SHALL BE CHECKED/ CERTIFIED BY ENGINEERING IN-CHARGE OR REPRESENTATIVE OF DGMTE-WS (HOS).LIFT OF 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY. 120 4002051686 INSTALLATION MOTOR,>150-400KW,LIFT<20M & INSTALLATION /ERECTING OF HORIZONTAL/VERTICAL PUMP/ COMPRESSOR/ BLOWER, MOTOR OF RATING OF ABOVE 150KW TO 400 KW AT DIFFERENT UNITS/ LOCATIONS/ AREAS OF TE-WS. THE MOTOR SHALL BE CHANGED FROM HORIZONTAL POSITION TO VERTICAL POSITION OR VICE VERSA AT SITE AS PER REQUIREMENT. THE SCOPE SHALL INCLUDE FITTING OF COUPLING IN THE MOTOR SHAFT, PLACEMENT OF MOTOR IN POSITION / BASE FRAME, FIXING OF FOUNDATION BOLT, ALIGNMENT AND COUPLING. ALIGNMENT SHALL BE CHECKED/ CERTIFIED BY ENGINEERING INCHARGE OR REPRESENTATIVE OF DGMTE-WS (HOS). LIFT OF 20 METERS & LEAD UP TO 50 METERS. ALL TOOLS AND TACKLES REQUIRED FOR THE JOB SHALL BE ARRANGED BY THE PARTY. Ea 20 130 4002292228 MKG RACK & DOOR F/NEW ELEC STORE SMS-II MAKING OF RACKS AND DOORS FOR NEW ELECTRICAL STORE AT SMS-II. THE RACKS WILL BE FABRICATED WITH ANGLES, CHANNELS & PLATES. WELDING M/C AND OTHER TOOLS AND TACKLES REQUIRED FOR EXECUTION OF THE JOB WILL BE ARRANGED BY PARTY. STRUCTURAL MATERIALS LIKE ANGLE, CHANNEL & PLATES REQUIRED FOR EXECUTION OF THE JOB WILL BE SUPPLIED BY INDENTOR. Ea 10 140 4002292227 MKG PORTABLE CBL STRAND W/THE ROLLER MAKING OF PORTABLE CABLE STRAND WITH THE ROLLERS & STRUCTURALS AS PER THE SKETCH ATTACHED. (FIG. - II) . STRUCTURAL MATERIALS REQUIRED WILL BE SUPPLIED BY INDENTOR. ALL OTHER CONSUMABLES, TOOLS AND TACKLES REQUIRED FOR EXECUTION OF JOB WILL BE ARRANGED BY PARTY. Ea 30
