Tender For Special Repair To Bldg No P-05 At Adhoc Transit Camp, Matiana Under Ge 863 Ews; 1 Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr in Charge. 2 Demolition of reinforced cement concrete in any position complete all as specified and directed by Engr in Charge. 3 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr in Charge. 4 Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engr in Charge. 5 S&F pre-painted galvalume aluminium zinc coating GI based corrugated/crimped steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in Charge. 6 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in Charge. 7 Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling complete all as specified and directed by Engr in Charge. 8 M&L for stone walling of squared rubble, uncoursed, well bonded, bedded and solidly hearted, built inCM 1:6 complete all as specified and directed by Engr in Charge. 9 M&L 1:3:6 type C-1 precast cement concrete (20mm graded stone aggregate) block masonary with solid blocks exc 10 cm in width and not exc 20cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr in Charge. 10 M&L for providing reinforced cement concrete 1:2:4type B1 ( 20 mm graded stone aggregate) as chajja , shelves etc complete all as specified and directed by Engr in Charge. (Note :- Reinforcement shall be measured and paid separately under respective item) 11 Use & waste form workrough finished surfaces of concrete to chajja ,shelves , troughs and similar items including edges complete all as specified and directed by Engr in Charge. 12 S&F mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing wire complete all as specified and directed by Engr in Charge. 13 M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) complete as in levelling of floor etccomplete all as specified and directed by Engr in Charge. 14 M&L for light shade Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm,as infloors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe shade of tiles over and including 15mm thick cement screed bed or bedding layer in CM (1:6) complete all as specified and directed by Engr in Charge. 15 M&L forlight shade Vitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in Skirting set and jointed in cement slurry over and including 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr in Charge. 16 M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles, throating and necessary form work complete all as specified and directed by Engr in Charge. 17 Taking down cementplaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr in Charge. 18 M & L for rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brick-workor concrete surfaces in cementmortar 1:4 using WPC 3% by weight of cement (WPC to be measured and paid separately) and finished even and smooth (without using extra cement) complete all as specified and directed by Engr in Charge. 19 M & L for rendering 10 mm thick on stone masonry surfaces or surface other than fair face of brick-workor concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement) complete all as specified and directed by Engr in Charge. 20 Supply only integral water proofing compound of approved brand/make. complete all as specified and directed by Engr in Charge. 21 M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of Chalk whitening complete all as specified and directed by Engr in Charge. 22 M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over a coat of wall care putty on walls,complete all as specified and directed by Engr in Charge. 23 Taking down chowkats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames) complete all as specified and directed by Engr in Charge. 24 S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed by Engr in Charge. 25 S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDMrubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete all as specified and directed by Engr in Charge. 26 S&F 4.8 mm thick tinted glass selected type quality n exc 0.5 Sqm in each pane for aluminum doors/ windows including rubber gasket/neoprene pad etc complete all as specified and directed by Engr in Charge. 27 S&F 4.8 mm thick tinted glass selected type quality exc 0.5 Sqm in each pane for aluminum doors/ windows including rubber gasket/neoprene pad etc complete all as specified and directed by Engr in Charge. 28 M&Lfor5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC/aluminiumframe as per specificationscomplete all as specified and directed by Engr in Charge. 29 S&F mortice brass lock vertical type size 100mm with 4 levers complete all as specified and directed by Engr in Charge. 30 S & F 100 mm butt hinges, medium weight, cold rolled mild steel and fixed. complete all as specified and directed by Engr in Charge. 31 S & F 150mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr in Charge. 32 S & F 200 mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr in Charge. 33 S & F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring overall length of cover plate 140mm complete all as specified and directed by Engr in Charge. 34 S&F Aluminium (die cast ) body door closer hydraulically regulated designation No 3 universal type, suitable fo door shutters of 851 to 1000 mm in width andof weight between 61 to 80 Kg. complete all as specified and directed by Engr in Charge. 35 M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed by Engr in Charge. 36 M & L for preparation of old steel surfaces of any description , over 10 cm in width or girth not otherwise described one coat of synthetic enamel paint complete all as specified and directed by Engr in Charge. 37 M&L 50 mm thick PCC (1:3:6) C-1 using 20mm graded stone aggregate as in plinth protection etc. finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. 38 Dismantling wrought iron or mild steel work of any description nototherwise provided complete all as specified and directed by Engr in Charge. 39 S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting platesetc confirming to Fe 410-W (grade -E-250) quality B complete all as specified and directed by Engr in Charge. 40 Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness inclduding cover fillets complete all as specified and directed by Engr in Charge. 41 S&F 8mm thick calcium silicate board (size 600mmX600mm) of siliceous and calcareous material reinforced with cellulose fibre in grid incl aluminium anodised snap grid frame 605X605 mm for false ceiling (Angle 25mm X 25mm , Main tee 38mmX23mm ,Sub tee 23mmX23mm) incl necessary hanging arrangement complete all as specified and directed by Engineer in Charge.Note: The rates of Scaffolding is deemed to be included in the quoted rate. 42 Taking down wall panelling and similar work complete all as specified and directed by Engr in Charge. 43 M& L for Hollow PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES schedule part-I & II complete all as specified and directed by Engineer in Charge . 44 M&L 75 mm thick PCC in 1:4:8 type D-2 using 40mm stone aggregate as in sub base etc complete all as specified and directed by Engr in Charge. 45 M&L 60mm thick Coloured (Yellow & red) interlocking (M-35) cement concrete tiles with grey cement and pigment of approved design & pattern as approved by GE. complete all as specified and directed by Engr in Charge. 46 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed by Engr in Charge. 47 M & L forpoint wiring using approved colour coding as per IS by using FRLS PVC insulated 1.5 Sqmm multistranded,1100 volt grade copper conductor cable unsheathed type, alongwith 1.5 Sqmm FRLS PVC insulatedstranded copper conductor cable for continous earthing in & incl casing capping point wiring with accessories having ISI mark for one light/fan/bell point/5 amp indep/power point/same board controlled by one switch complete all as specified and directed by Engr in Charge. 48 All as per item No 2 here-in-before but for one multipin socket outlet 5 Amp but using 2x 1.5 + 1 x 1.5sqmm multistranded FRLS copper cable onthe independent board complete all as specified and directed by Engr in Charge. 49 All as per item No 2 here-in-before but for one multipin socket outlet 5 Amp on the same board with other switches complete all as specified and directed by Engr in Charge. 50 All as per item No 2 here-in-before but for one multipin socket outlet 15 Amp,but using 2 x2.5 +1 x 2.5sqmm multistranded FRLS copper cable, independent board complete all as specified and directed by Engr in Charge. 51 S & F in replacement of switch piano type 5 Amp, 230 Volt, flush type single pole one waycomplete all as specified and directed by Engr in Charge. 52 S & F in replacement of socket outlet multipin 5 Amp 230 Volt flush typecomplete all as specified and directedcomplete all as specified and directed by Engr in Charge.. 53 S & F in replacement of switch piano type 15 Amp, 230 Volt, flush type single pole one waycomplete all as specified and directed by Engr in Charge.. 54 S & F in replacement of socket outlet multi pin 15 Amp 230 Volt flush type complete all as specified and directed by Engr in Charge. 55 S& F In replacement offorLamp holder, PVC/Polycarbonate type with back plate suitable for Angle/batten fittings complete all as specified and directed by Engr in Charge. 56 S&F of rechargeable led bulb minimum 4 Hrs Battery backup 9 Watt B-22 Base complete all as specified and directed by Engr in Charge. 57 S& F in rplacement of Ceiling rose, 3 terminal, PVC isolated body complete all as specified and directed by Engr in Charge. 58 S & F in replacement of LED light fitting 20W, 220 volt AC, having colour temperature daylight (6500K), Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr in Charge. 59 S & F in replacement ofsheet metal enclosure double door distribution board single pole and neutral, 8 way 240 volt with 100 amps rated bus bar complete with bus and neutral linkcomplete all as specified and directed by Engr in Charge. 60 S & F in replacement of MCB 6 to 32 amp rating 240V, 10KA B curve, Single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr in Charge.d. 61 S & F in replacement of MCB SPN 40 amp2 amp rating 240V, 10KA B curve, Single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr in Charge. 62 Supply & laying LT UG XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 Volts grade cross-sectional area 16 sqmm 2 core as per IS specification laid through GI pipe/on floor/wall complete all as specified and directed by Engr in Charge. 63 Supply and laying of GI pipe light galvanized with all fitting laid in trenches for cable proctection of 50 mm bore complete all as specified and directed by Engr in Charge. 64 M & L in replacement of Earthing complete with galvanised steel earth plate electrode 600×600×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mmdia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on complete all as specified and directed by Engr in Charge. 65 Supply and fixing Building LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermalmanagement in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr in Charge. 66 Excavation in trenches not exc. 1.5 m wide and not exc 1.5 mtr deep in hard soil for laying / taking up/ taking down of cablesand getting out and leveling of bottom surface to required level all as specified and directed by Engineer- in- Charge. 67 Returning filling in,. Including spreading, leveling,. Watering and well ramming soil in layers not exceeding 25 cm thick complete all as specified and directed by Engr in Charge. 68 Removing excavated material (i.e. soil) from site to a distance n. exec 50 mtrs away and depositing where directed at a level n. exc. 1.5 mtr above the starting point all as specified and directed by Engineer-in-Charge. 69 S & F ofWall fan 450 mm minimum 1400 rpm 125CMM220 Volt copper winding motorcomplete all as specified and directed by Engr in Charge. 70 Supply and fixing air termination single pointed aluminium rod 12 mm 300 mm long include fixing on aluminium flat saddle on roof/wall with ms clamp/ nut bolt washer complete all as specified and directed by Engr in Charge. 71 M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised earth strip 32 x 6 mmmeans of bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 40 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion.complete all as specified and directed by Engr in Charge. 72 M & L for GI strip 32 mm x 6 mm complete with saddles and fixing screws for fitting the strips complete all as specified and directed by Engr in Charge. 73 M & L test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hex. Head screw all as directed by Engineer-in-charge. 74 S & F in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC, having colour temperature daylight (6500K), Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling including connecting up three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr in Charge.
